Search Documents

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By Sigmund D. Schwarz

INTRODUCTION In late 1970, an experimental geophysical program was undertaken at the Lake Huron Tunnel for the purpose of developing a geophysical technique that could be applied to determining the thickness of rock above the crown of the tunnel and identifying anomalous geologic conditions ahead of the face as the tunnel was advanced. The Lake Huron Tunnel is an 18.5 foot diameter machine bored tunnel having a total length of approximately 6 miles. The easternmost 4.5 mile section of the tunnel extends offshore beneath Lake Huron. At the time this study was started, approximately 1.5 miles of bore remained to be completed at the east end of the project. The tunnel is part of a raw water intake for the City of Detroit water supply. The Lake Huron Tunnel is bored in Antrim shale, a dense marine shale of Mississippian or Devonian age. The west end of the project encountered banded brown shale containing numerous calcareous concretions ranging in size from a few inches to more than 16 feet in diameter. As the tunnel was advanced in an easterly direction, a transition was encountered into very uniform gray shale. One set of prominent vertical joints was encountered with a strike running approximately 15 to 20 degrees askew of the tunnel axis. Bedding is essentially flat. Variable quantities of salt water and natural gas occur in the rock. The results of exploratory drilling carried out for preliminary design studies indicated that as little as 30 to 35 feet of rock cover could be expected under the lake at the east end of the project.

Jan 1, 1997

By H. G. Fleshman

The economics of western sodium bentonite (also known as Wyoming Bentonite) is covered from exploration to delivery to the final user. Included are costs of exploration, evaluation of ore bodies, mine permitting, stripping, loading, hauling through stockpiling, blending, processing and shipping. Since western bentonite is one of the industrial minerals marketed throughout the world, the various markets and freight costs are included.

Jan 1, 1984

By Richard Louis Viner, William D. Leech, Walter A. Mergelsberg

With the construction management team established and a full funding agreement secured the Washington Metropolitan Area Transit Authority (WMATA) now has the manpower and the financial resources to continue Metrorail construction into the 1990's. This paper describes WMATA's new role as construction manager after the transition from Bechtel Associates and gaining the full funding agreement with the Urban Mass Transit Administration (UMTA) and regional governments to complete 84.7 Metrorail miles (136km). The authors review the most recent station and line tunneling projects. WMATA's contractors have employed the state of the art soft ground and hard rock tunneling equipment and methods - an earth pressure balance TBM, a closed face TBM, and the New Austrian Tunneling Method (NATM). In final, the paper previews future underground work to be let under the funding agreement.

Jan 1, 1987

By William F. Riggs

In the fresh application of a frother, collector, or the change of any particular reagent, the interaction caused by this change is often overlooked since we attempt to solve a problem or improve a situation with use of a particular reagent without regard for the Interactions or side effects. When a particular reagent is added to a flotation circuit or substituted for another reagent, a series of chemical reactions occurs which. In turn, will create different physical responses. This discussion will provide a series of examples which have actually been experienced by the author.

Jan 1, 1994

By H. L. Bourne

Not everyone understands the concept of mineral royalty. Mineral royalty is a fee paid to a landowner by someone who extracts a mineral commodity from the owners property. The royalty contract between the lessor and lessee contains clauses and conditions that are significant to both parties, e.g., annual m1n1mum, escalation factor, duration of the lease, reclamation and assignability. Comparison of royalty rates requires knowledge of many conditions that influence the value of a given deposit. People in several different professions benefit from shared royalty information.

Jan 1, 1989

By Steven A. Atkin, William D. Schrand

Closure plans for open pit mines require the prediction of final pit lake water chemistry. The geochemical models used for water quality predictions make assumptions about the physical and chemical behavior of the water in the lake; however, few pit lakes have been well documented to provide empirical data for model design. The pit lake at the Sleeper Mine has been characterized with regular water chemical analyses and regular, continuous, multi-parameter profiles through the water column. The lake has undergone repeated periods of chemical and thermal stratification, punctuated by rapid turnover events resulting in vertical homogenization within the water column.

Jan 1, 2000

By B. Stewart, R. Li

Coal waste materials inhibit the direct establishment of vegetation due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss #1 coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980s with little topsoil resources available for final closure. The refuse was acidic (Total S = 0.38%; pH = 3.6), black in color and high (70%) in coarse fragments. The refuse also had a low water-holding capacity (4.5% in < 2.0-mm fraction). A small plot experiment was established on the refuse pile to evaluate the effects of liming rates (50% and 100% of lime requirements) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from <4.0 to >6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only. This was due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Applica¬tion of 27Mg ha`1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and this appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity of leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile. Therefore, long-term water-treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 2000

By Dominic F. Howarth

Cuttability and borability assessment methods in rock and coal are reviewed. TBM, roadheader and coal cutting machine boring rates can be predicted from a knowledge of machine, intact rock property and rock mass parameters. Results that were obtained from a detailed analysis of two TBM borability prediction methods and comparison with data from twenty case histories, show that a simple, low-cost method that uses one machine parameter and one rock parameter compares very favourably with a sophisticated, high-cost method that also includes details of rock mass characteristics (discontinuity, type frequency and orientation).

Jan 1, 1987

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the con¬ventional petroleum production cycle in then-known fields within the U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oil-or bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67% of the OOIP will remain in place at the end of the

Jan 9, 1980

By K. Biswas

In general, it cannot be assumed that the strength of coal pillars remains constant over long time periods. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing load-bearing capacity of the pillars. This paper discusses a unique approach to determine the time dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15 and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar and the strength profiles were determined for each hole using the Borehole Penetrometer. The strength data were treated statistically to establish time dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 1999

By Otis M. Clarke

Domestic bauxite used in aluminum production comes from Arkansas where syenite was lateritized forming bauxite. Part of the residual bauxite and kaolinized syenite were eroded, deposited downdip, lateritized with bauxite formed in place, and covered by sediments. The unconsolidated overburden causes problems in mining. Bauxite for refractories and chemicals comes from Alabama and Georgia. Sediments were deposited in karst lakes and were lateritized forming bauxite and kaolin. Ferruginous bauxite in Washington, Oregon and Hawaii, derived from weathered basalt, can be used in aluminum production.

Jan 1, 1984

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920&apos;s, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

Improvements in cost efficiency, noise control, environmental design and ergonomics ? the mining and construction industries are facing demands on many fronts. The international manufacturers of construction machinery are responding to these challenges, and they will be presenting their innovations in all these fields at bauma 2013. bauma, the international trade fair for mining and construction machinery, mining vehicles, and building material machines, takes place from April 15 to 21, 2013 at the Messe Munchen exhibition center in Munich, Germany. The last bauma, in 2010, attracted 3,256 exhibitors from 53 countries, and more than 420,000 visitors from more than 200 nations. Covering a total of 555,000 m2 (5.97 million sq ft) of exhibition space, bauma is one of the largest trade shows in the world. This year?s fair is expected to surpass the 2010 figures. Here are some examples of the new developments visitors can expect to see at the show.

Jan 1, 2013

By S. W. Swerson

25.1-THE PURCHASING FUNCTION The word "purchase" means "to obtain by paying money or its equivalent; to buy for a price." This definition is all too simple to properly describe the word "purchase." One should consider the basic objectives of purchasing-to procure the right material, of the right quality, in the right quantity, at the right time, from the right source at the right price. Here it should be noted that in purchasing it is recognized that the best quality or grade of materials may be the only grade to purchase for a specific job. However. there are other jobs where the medium, standard or poor grade of materials is the right quality, as the lesser grade will perform adequately. In some companies the purchasing department makes the decision as to the right quality, while in others this function is shared with other departments. Years ago in business the owners controlled the purchase of required materials and services by performing the task themselves. The owners obtained the type materials and services they needed and paid the price demanded. This function was performed along with all the other duties requisite to the owner of a business, namely, clerical, hiring and firing of personnel, financial management, etc. As companies grew in size, clerical duties were assigned to other personnel and the owner usually retained the purchasing authority. This same division exists today in many small companies. However, in the larger companies, the purchasing function has been assigned to a separate department. Importance of the Purchasing Function-The larger the company the greater the need for a separate department to perform the purchasing function. Today the purchasing agent for most larger progressive companies has policy-making authority. Therefore, it is reasonable for him to report to the president or vice president of his company. Studies of several hundred companies show the purchasing department head reporting to top management 87.5% of the time. This fact in itself is indicative of the importance of recognizing that effective purchasing requires a department staffed with specialists in the field of procurement with knowledge and experience sufficient to perform in today&apos;s complicated business atmosphere. In the manufacturing field it is a common axiom that usually half of the company&apos;s dollar expenditures are for materials. If a purchasing department functions properly and the right product or service is purchased and a savings accomplished, the contribution to the net profit of the company is much greater, as opposed to sale dollars, where only a small portion is carried forward to net profit. Thus, the importance of the purchasing department and the contribution it can make to the success of the company are obvious. 25.1.1-THE PURCHASING FUNCTION 1. Responsibilities of the Purchasing Function-The purchasing agent in performing his function is acting as an agent for the company and others in the company requiring materials and services. Accordingly, he is committing the company for materials and services subject to certain limitations which the board of directors may stipulate. In view of this, the purchasing agent,&apos;^ position must of necessity he

Jan 1, 1973

Simulation has established itself as an accepted tool for the design and optimization of complex minerals processing plants. This paper addresses the use of simulation as a tool for the design and optimization of carbon-in-pulp and carbon-in-leach (CIP/CIL) plants. The complex, interactive nature of CIP/CIL plants makes detailed experimentation an expensive and time consuming approach to CIP/CIL plant design and/or optimization. This paper discusses a simulation-based software tool that can make the process of CIP/CIL plant design and/or optimization much more cost effective. Many of the issues and problems pertaining to the use of simulation for CIP/CIL design and operation are generic. Thus, this paper also attempts to highlight generic issues that must be solved before simulation will become a more widely used design and optimization tool. Requirements for the application of simulation for CIP/CIL plant design and optimization are highlighted. Similar problems and issues can be identified for most mineral processing plants.

Jan 1, 1994

By M. Fan

Coal has in general a wide range of density from minus 1.3 to plus 2.0 g/cm3 because of its variations in purity, rank, and porosity, etc. The coal density has great impact on froth flotation performance, but much less attention has been paid to particle density than particle size. Our previous research results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different density fractions (minus 1.3, 1.3-1.4, 1.4-1.5, 1.5-1.6, 1.6-1.8, 1.8-2.0, 2.2-2.2, and plus 2.2 g/cm3) of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50-mm-inside-diameter column, and a 152-mm-inside-diameter column. It was found that nanobubble has the biggest impact on the flotation performance of 1.4-1.8 g/cm3 medium-density coal particles.

Feb 23, 2014

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant&apos;s ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator&apos;s end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969