Search Documents

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By Louis A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (such as shown by figure 1) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening (3), is excluded from consideration herein.

Jan 1, 1964

By J. D. Isbister

Coal is the most abundant and most economical source of energy in the United States, however, combustion of coal results in release of pollutants to the environment. The release of sulfur dioxide and oxides of nitrogen during combustion of coal contributes to the deterioration of the environment. Energy independence in the United States must include the increased use of coal reserves. Increased reliance on coal for energy will dictate the necessity for making coal a cleaner fuel. New technologies employing a variety of techniques from harsh chemical treatment to mild physical separations to clean coal are rapidly becoming available. Success for any coal cleaning process is in economics which translate into efficient removal of sulfur with high recovery of combustibles as well as low capital and operating costs for the process. Conventional coal cleaning processes remove water soluble sulfates and a portion of the pyritic sulfur and ash from coals. Removal of additional sulfur from coals requires more advanced coal cleaning techniques. Coal contains many organic sulfur forms which are the most difficult of the sulfur types to remove from coal. The heteroaromatic sulfur species, such as the comlex thiophenes, are the most commonly found organic sulfur forms. These sulfur forms are resistant to chemical attack and are considered to be refractory compounds. Atlantic Research Corporation has developed an "unique" microorganism, CB1 (Coal Bug 1), capable of oxidizing thiophenic sulfur in coal to form water soluble sulfates.

Jan 1, 1986

By K. K. Bhattacharyya, S. Bhattacharya, S. Dey

Coal batch flotation tests were conducted both with and without collector and with one- and two-stage additions of frother. The recovery of combustibles and the flotation rate constant were found to be higher with two-stage frother addition, both with and without collector.

Jan 1, 1998

Perhaps the most significant development in China's base metal sector is the discovery of major copper porphyries in northern Jiangxi Province and the adjacent southern Anhui Province. At the center of the new exciting district is the proposed Dexing copper complex, located some 350 km east of Nanchang, the provincial capital of Jiangxi. This project represents China's first attempt to put together a major large-scale open-pit operation, comparable in magnitude to Arizona porphyry operations. With the aid of Fluor Mining and Metals, the Chinese plan to develop a 135-175 kt/d open-pit mine, a matching large-scale mill, and the infrastructure needed to accommodate the big operations. An operation of this magnitude would significantly reduce China's import requirements by some 75%. China imports of the red metal are running around 200 kt/a. Under the direction of the Ministry of Metallurgical Industry, the Chinese are currently operating a 10-kt/d mine and mill with equipment primarily of Chinese origin. Dexing engineers told ME that they are considering a possible scale-up to 20 kt/d. How this effort will ultimately jell with the major expansion program is largely a matter of conjecture. Fluor Mining and Metals received a $10-million contract in December 1978 to develop a preliminary engineering and design program. While the original plans called for a 175-kt/d capacity complex, the Chinese subsequently decided to scale it down somewhat. The current proposal is around a 135 kt/d, which would in- elude the existing operation, according to Dexing engineers. Completion of the engineering and design phase is expected by March 1980 and a go-ahead decision will likely be made at that time. The value of the engineering and construction contract is estimated between $800 million and $1 billion. At right, mined ore is dumped 150 m down the mountain to a holding pocket below for rail haulage to the processing plant. Below, a Chinese miner tackles the universal problem of hard toes in the pit with a jack leg. Reserves and Early History The Dexing mineralization consists of three principal ore bodies, including the Chushahung on the north mountain, and the Tungchang and Fuchiawu on the south mountain. Combined ore reserves are estimated by mine geologists at 1.7 Gt of 0.4-0.5% copper. As is characteristic of porphyries, the ore contains important associated values of molybdenum, rhenium, pyrite, gold, and silver. There is also some secondary calcocite and bornite with an oxidized capping. Historically, copper was recovered with iron from the pregnant solutions emanating from the Tungchang deposit as early as the Tang Dynasty (700 AD). Modern day exploration was conducted by the Bureau of Geology in 1956 and reserve figures were es-

Jan 3, 1980

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By Y. A. Attia

Auriferous sulfide ores often contain very finely disseminated gold and other precious metal particles inside the sulfide crystals. The encapsulation of precious metal particles gives rise to the refractory nature of such ores to current extraction methods. As a result, these fractions are frequently lost in the tailings. The purpose of this work was to investigate the feasibility of pretreating these refractory tailings with bioleaching before employing standard extraction techniques such as cyanidation. Leadville gold ore tailings containing auriferous pyrite were first concentrated by froth flotation. The pyrite concentrate was treated for different periods of time with 12 weeks adapted thiobacillus ferrooxidans before cyanide leaching. The bioleaching of the concentrate before cyanide leaching increased the gold extraction from 32% to 95% and that of silver from 48% to more than 98%.

Jan 1, 1987

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By Milton E. Wadsworth, M. Ken Han

The kinetics of leaching of galena in hydrochloric acid solutions with sulfur dioxide gas have been investigated experimentally. The leaching method is then applied to complex sulfide concentrates to evaluate its selective leaching capability and to develop a new hydrometallurgical lead extraction process based upon the method. The leaching reaction follows a linear rate with an activation energy of 61.9,KJ/mole. The rate Is of first order with respect to the product [H+] [Cl-] . Excel lent selective leaching capability f s demonstrated and an attractive hydrometallurgical process flow sheet is proposed.

Jan 1, 1989

By A. Dale Wunderlich

With the price of precious metals at an 18-year low, every ounce of metal produced is important. The theft of metals from mining and refining sites can mean the diffrence between profit and loss for many mining companies. Low metal prices do not reduce the potential for the theft of precious metals. History has shown that the price of gold has little to do with the desire for employees to steal precious or base metals. There is actually evidence that the theft of precious metals increases when the price of this commodity goes down. Several of the major precious metal thefts in the past year took place at silver mines when the price of silver was less than 16 cents/g ($5/oz). How does the lowest gold price in 18 years affect the need for security at precious metals properties? There is no short answer to this question. One reason is because the exposure to theft of precious metals is unique to each property. This makes it important that each property be evaluated individually. More than 95% of all precious metals thefts can be attributed to those working at the mine site. So preventing employee theft is the primary concern. One consideration is the location of the property. Gold selling at any price is still an attractive commodity in countries where the employees are making between US$400 and US$600 a month. It is not uncommon for employees at mines in countries where low wages are the norm to consider the value of a gram or two of gold to be a significant amount of money. A gram or two of gold a day may not seem like much. But if 15 employees steal two grams a day, that equates to a significant amount of money during a year. The type of property where the precious metals product is being recovered is also important. For example, a property with a gravity circuit is more likely to suffer from the theft of gold product than a property where all gold is finely disseminated and the only gold seen in the ore body is through a microscope. Gravity circuits increase an operation's exposure to theft because the grinding circuit that is associated with a gravity circuit often becomes a giant concentrator. Areas such as the bottom of grinding-mill pump boxes, cyclone-feed-pump clean out traps and the sumps often become locations where precious metals concentrate (Figs. 1 and 2). Muck concentrations in these locations can be as high as 25% to 40% of gold or silver. Not long ago, muck was removed from a barren-solution sump at a Merrill Crowe circuit that had concentrated to more than 40% gold. At a milling site in the Pacific Rim, residents of the community adjacent to the mine learned about the value of the concentrates in the sump under the ball mill and committed an armed rob¬bery. While several of their co-conspirators held the em¬ployees at bay with machetes, the others emptied the contents of the sump into buckets and removed it from the site. Armed robbery is not as common as employee theft. However, while this article was being written, an armed robbery occurred at a gold property in Central America. Armed perpetrators took as hostages the night shift employees at a process plant and used cutting torches that were on site to cut into the high-security and gold-storage areas. The perpetrators then stole a company vehicle to remove the stolen gold buttons and sludge from the site. Unfortunately, this type of activity goes on regularly. But managements of most mining companies are reluctant to discuss theft scenarios. So information pertaining to the theft of precious metals seldom becomes a newsworthy item. An audit conducted at a mine site with a gravity circuit recommended that the gravity recovery area be shut down until adequate protection could be provided. Although it was not connected with the audit, it was necessary to shut down the gravity area for a pro¬longed period because of problems with the gravity table. In the two months that followed, gold production at the site increased by about 31 kg/month (1,000 oz/month). It is difficult to attribute all of this increase to the theft of concentrates. But there was a good chance that at least part of the increase was due to the fact that concentrates were being stolen from the gravity area.

Jan 1, 1998

By F. L. Pirkle, W. C. Bagby

The International Mineral Valuation (IMVAL) Committee, founded in 2012, develops strategies for conducting mineral valuations. These strategies have been developed into a mineral asset valuation template called the International Mineral Property Valuation Standards Template and is part of IMVAL's work to establish consistent international standards for mineral property valuation and reporting. This template is a living document that is updated from time to time and is based on three core values or pillars (Fundamental Principles): Competence, Materiality, and Transparency. Objectivity, Independence, and Reasonableness may be applied as required by national codes or standards. The Template harmonizes international standards for valuation of mineral assets as real property and represents a consensus of current good practices. It is not a stand-alone reporting code and does not supersede existing national reporting standards. The Template deals with mineral-property valuation as distinct from mineral-project evaluation. INTRODUCTION In his 1989 book, “The New Realities”, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, California, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized.” (p. 209) The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze, and interpret data that are material to a mineral valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality, and transparency, the three pillars of mineral valuation (“minerals valuation”, “mineral-property valuation”). The International Mineral Valuation Standards Template (“IMVAL Template”, IMVAL”, “Template”), third edition dated May 2018, defines mineral valuation as: “The estimation of the Value of a Mineral Property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the Valuation conclusion) or to refer to the preparation of the estimated Value (the act of valuing).” (p. 14) Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The Template deals with Valuation, which is distinct from Evaluation. The distinction inherent in these defined terms is that Valuation addresses the estimation of value of a Mineral Property, whereas Evaluation addresses the broader assessment of a Mineral Property for an investment decision.” (p. 2)

Jan 1, 2019

By J. C. Judd

The U.S. Department of the Interior, Bureau of Mines investigated solvent extraction methods for recovering gallium from filtrates produced from sulfuric acid leaching of hydrometallurgical zinc residues. These filtrates typically had pH values of 0 to 0.5, too high an acid content for effective gallium recovery by traditional extractants. Of the nine extractants studied in batch tests, 0.3M octyl phenyl acid phosphate (OPAP) in a kerosene diluent was the most effective extractant for gallium recovery, extracting up to 99.9 pct of the gallium. This high extraction was possible when the iron in solution was maintained in the reduced ferrous state. Batch tests also showed that a 1.5M-H2SO4 strip liquor recovered 98 pct of the gallium from the loaded OPAP. A continuous solvent extraction system was designed and operated based on McCabe-Thiele analyses of equilibrium loading and stripping isotherms. When 12 L of leach filtrate containing 0.32 giL Ga and 20 giL Fe were pumped through the system in 32 hr, results showed that 95 pct of the gallium was extracted in four stages at an A:O ratio of 1:1. Stripping the loaded solvent with a 1.5M-H2S04 liquor recovered 94 pct of the gallium in four stages at an A:O ratio of 1:4. A two-stage, 50-pct-phosphoric acid strip successfully removed ferric iron from the OPAP, allowing high gallium extractions to be maintained.

Jan 1, 1990

Acid Mine Drainage (AMD) is the most serious environmental problem facing the Canadian Mineral Industry today. Acid Mine Drainage results from oxidation of sulphide minerals (e.g. pyrite or pyrrhotite) contained in mine waste or mine tailings. It is characterised by acid effluents rich in heavy metals that are released into the environment. A new acid remediation technology is presented in this paper by which metallurgical residues from the aluminium extraction industry are used to construct permeable reactive barriers (PRB) to treat acid mine effluents. It describes column tests performed to simulate a PRB using Bauxsol?, a chemically and physically treated bauxite refinery residue, as a reactive material. This experimentation shows promising results for the Bauxsol? PRB method in neutralizing pH and removing metals from acidic mine effluents.

Jan 1, 2006

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

"The 35th Annual American Mining Hall of Fame Awards Banquet and Fundraiser, sponsored by the Mining Foundation of the Southwest (MFSW), will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 2, 2017. This year, the Foundation will honor one living Hall of Fame inductee, two Medal of Merit recipients, four honorees from Mining’s Past and an Industry Partner for their respective contributions to the mining industry.Gary J. Goldberg will be the 2017 Hall of Fame Inductee and will serve as the keynote speaker at the awards banquet. Goldberg was appointed president and chief executive officer and joined the board of directors of Newmont Mining Corp. in March 2013. Prior to this appointment, he served numerous companies in key positions including Rio Tinto Minerals, US Borax and Coal & Allied Industries. At every appointment, he was able to improve safety concerns and reduce injury rates. While serving as chairman of the National Mining Association, Goldberg launched the CORESafety initiative and US Borax was the first mining company to receive the California Governor’s Environmental and Economic Award.The Medal of Merit will be awarded to John C. Lacy, a shareholder of DeConcini McDonald Yetwin & Lacy, P.C. and a director of the Global Law Center at the University of Arizona’s Law School. Lacy’s law practice concentrates on mining and public land law and encompasses transactional and title consideration involving acquisition of mineral rights. He played a crucial role in the revisions to the mining law of the Republic of Bolivia and the English translation of the mining laws and regulations of Mexico. Lacy’s expertise in mining law impelled the University of Arizona James E. Rogers College of Law to approach him to head the new Global Mining Law Center in 2015. The program now partners with the Lowell Institute for Mineral Resources and offers cross-listing of courses"

Jan 10, 2017

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By H. Colijn

Introduction Bulk commodity prices are ever increasing. This forces buyers and sellers in world markets to look more carefully at methods for obtaining an accurate accounting of commodity transactions in commerce and materials utilization in processes. Weighing and sampling inaccuracies can result in loss of income, product quality, and cost controls. So weighing and sampling accuracies are extremely important. They are the key components of managing the quantity and quality control aspects of bulk materials handling. This article will confine itself to the weighing systems and will deal with various aspects of system design, calibration, and operations. Emphasis will be placed on new developments and requirements in this field. Weighing methods To measure the gravimetric pull on a body being weighed (the load), the gravimetric force must be countered by an opposing force. Measuring this counter-balancing force thus becomes the measurement of weight. The conventional even-arm balance shows the concept of balancing an unknown mass with an equal known counterbalancing mass. But the loads encountered in industry generally range up to many thousands of pounds. So it is obvious that the even-arm approach is not practical. Thus, with the exception of direct load-bearing load cells, most of the weighing equipment uses some form of lever system. This is usually a combination of first- and second-class levers, to gain a mechanical advantage. These levers permit the load force to be counter-balanced and hence measured within a practical range. Lever systems not only perform this force-reducing action, they also serve to focus the load force at a single point, for convenient measurement. They align the force vertically in one direction so that measurement accuracy will not be affected by unrelated side forces. There are five basic methods of gravimetric weight measurements. That is, there are five basic types of opposing forces. • The first is the standard weight counterbalance. It uses a known weight to counterbalance the load directly or through a lever system.

Jan 9, 1988

By Bernard Lippe

The successful construction project is one in which the component construction operations are completed within the scheduled time and cost parameters. Most construction projects, however, are subject to delays and/or disruptions which adversely affect the time (start, duration, and completion) and cost aspects of the project. DELAYS Delays fall into two categories: Compensable Delays for which the contractor is entitled to contract time extensions and additional money as compensation for the extra expenses generated by the delay or obstruction to job progress, and Non Compensable Delays, for which the contractor may or may not receive an extension of time but no additional compensation. Compensable Delays Compensable delays may take the form of holds or suspensions on all or certain segments of a project by the owner, failure of the owner or his Engineers to approve shop drawings, cuts or material samples within a reasonable period of time, failure of the Owner or his Engineer to properly coordinate the job, discovery of design deficiencies in the plans and specifications which prevent the continuation of construction until

Jan 1, 1974

By P. R. Dugan

The ultimate objectives and interest in removal of sulfur from high sulfur coal include: (a) reduction of the atmospheric load that con- tributes to the problem of acid precipitation; (b) reduction of ash which contributes to decreased energy transfer in boilers and the problem of ash disposal; and (c) alleviating the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. The cost of sulfur removal in relation to the value of refined coal will govern the development of an emerging coal-refining industry. The value of refined lower sulfur coal will be influenced by the national commitment to the environment as well as economic considerations.

Jan 1, 1986

By K. W. Lentz

The Maybell Mill of, Trace Elements Corporation, Unit of Union Carbide Corporation is located approximately five miles northeast of Maybell, Colorado, and twenty-five miles northwest of Craig. It is located in the midst of the uranium ore deposits whose presence, made it possible. In November 1953 Russel Cutter, Chief Geologist for the original Trace Elements Corporation, picked up high readings on a scintillometer while flying over this area. Later, with George Morehouse, Chief Engineer for the original. Trace Elements Corporation, he started a search for surface indications. In this search, they found an out crop which can be regarded as the discovery lode on this property. The actual locating of claims and acquiring free lands and state lands was begun in March 1954. During 1955 enough drilling was done to indicate that a sufficient tonnage of ore existed to make possible a mill. These ore deposits are located in the Browns Park formation which is an unconsolidated sandstone with a few hard lime ribs running through it. The geologists tell us that this region was once a vast basin which became filled with wind blown sand and volcanic tuff, Later on, ground waters brought uranium into the basin which precipitated out in the sand. During the late summer and fall of 1955, a small pilot plant was operated under the supervision of John L. Chapman testing these Browns Park ores. During the operation of the pilot plant, three small open pits were developed and the ore from these pits shipped to Union Carbide Nuclear Company, Division of Union Carbide Corporation, at Rifle. To date all ore is being mined from open ptis. In the fall of 1956 the original Trace Elements group signed a contract with: the AEC for a mill at Maybell and on November 5, 1956, Union Carbide acquired the Trace Elements Corporation properties and contract. During the next two months, intensive research was carried out on the Browns Park ores by our research lab at Rifle. They also checked some of the metallurgical results which had been obtained through the operation of the pilot plant by the original Trace Elements group. During this period, a report on Trace Elements Corporation ores was also prepared by the Colorado School of Mines Research Foundation. This report contained data on representative samples of the ore tested for the original Trace Elements group. From this research and study a flow sheet was decided upon.

Jan 1, 1959