Search Documents

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By N. D. Jagger

In order to maximize the benefits obtained from flocculating agents when used as settling aids in high rate and conventional thickeners, it is often necessary to dilute the thickener feed prior to flocculant addition. In some cases, no flocculation at all is possible unless dilution water is used. The most common method of diluting thickener feed has been to recirculate some of the thickener overflow by means of a centrifugal pumping system. This represents a significant capital and operating cost. Supaflo Technologies of Australia has developed and patented an internal recirculation method known as Auto Dilution (or "Autodil") which is based on the principle that an hydraulic head differential exists between the inside and outside of the feedwell because of the higher S. G. of the pulp inside the feedwell, By installing non-return ports in the feedwell wall at the appropriate level, supernatant solution flows into the feedwell at a calculated rate and dilutes the feed without any need for external recirculation of overflow.

Jan 1, 1993

Unless otherwise indicated, pounds are US avoirdupois, feet are US, and gallons are US.

Jan 1, 1985

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By F. S. Knoll

The high tension process which separates materials based on relative differences in surface conductivity has been very successful in recovering non-ferrous metals from municipal waste. Aluminum is by far the largest constitutent of the total non-ferrous metal fraction; accounting for >95% in most localities. Wire and insulation mixtures from industrial wastes have been treated commercially for several years by a high tension process initially developed for use in the iron ore industry. The wire and insulation application was a forerunner of municipal waste dry treatment technology. In the past eighteen months the rotating-drum-type electrostatic separator has undergone extensive testing and development in order that the process might be efficiently adapted to the recovery of aluminum from municipal waste.

Jan 1, 1974

By William J. Miles, Raymond E. Blair

The oil and gas drilling industry is the largest user of "functional" industrial minerals for well drilling and completion. (Functional industrial minerals can be defined as those used for performance characteristics rather than composition.) This industry's use of industrial minerals involves complex mining, processing, and distribution of products. The cost of these products at the well site reflects the complexity of distribution to typically remote locations and the cost of service. Table 1 illustrates the use of functional industrial minerals by the drilling industry. The total tonnage shown is almost 2 1/2 times larger than the 3.3 Mt (3.6 million st) of kaolin used by the paper industry for filling and coating, another major use for functional industrial minerals. Drilling fluids are an indispensible part of a drilling operation. These fluids perform several functions simultaneously. They cool and lubricate the drill bit, remove formation cuttings, increase the specific gravity of the fluid to counteract formation fluid pressures, provide a filter cake on the wall of the drill hole to prevent drilling fluid loss to the formation, protect the porosity of producing zones, and prevent reaction of the formation or formation fluids with the drilling mud. When porosity of a formation exceeds the ability of the drilling fluid to form a wall cake, it is referred to as lost circulation. Because these fluids are being constantly formulated for changing formation conditions, they require a skilled technician or drilling mud engineer on the site at all times. Drilling fluids are composed of oil or water as the liquid phase, and industrial mineral products and chemicals to control chemical and physical properties. The basic function of viscosity and suspension result from the use of gelling clays and chemical and mineral dispersants; specific gravity of the mud is adjusted with mineral weighting agents; filtration control is maintained by clays and various natural and synthetic polymers; platey minerals and scrap products are used for controlling lost circulation in porous or fractured zones; salts are added to the mud to inhibit shale and clay swelling; chemicals are added for pH adjustment, prevention of corrosion, and as scavengers for formation fluid components. Because of the clay component, drilling muds have rheological properties different from conventional fluids, behaving as Bingham plastic fluids as opposed to the Newtonian behavior of water and oil. Newtonian fluids will begin to flow with the application of any force, however small. Bingham plastic fluids require a finite force or shear stress (yield value) before flow begins. Thixotropy is another property of clay-based drilling fluids. At rest they form a gel structure that suspends the weighting agents and rock cuttings. These gels break down when a finite force is applied and circulation is restored. At the bit where shear rates are the greatest, the viscosity or resistance to flow decreases, so hydraulic pressures and pumping costs are minimized. A drilling rig provides a means of rotating a hollow pipe attached to a cutting bit. A mud pit or tank is used for mixing the drilling mud and its components. A centrifugal pump delivers this fluid to the drill ripe and down to the bit

Jan 10, 1983

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By K. Wenrich

The uranium industry has made a dramatic turnaround in the past three years that even the most optimistic economist was not willing to predict during the uranium downswing of the 1990s. Uranium reached a 30-year low in February 2001 of $6.50/lb. By the end of February 2006 it had soared to $38.50/pound. This nearly 600% increase in the uranium spot price within 4 years dwarfed the increase in gold price that has barely mustered a 100% increase. The initial slow rise from $6.50 in February 2001 to $10.75 in April 2003 (fig. 1) was primarily driven by the decrease in the value of the dollar. Since then several factors have contributed to the soaring price: (1) The awakening of many to the simple fact that uranium supply has not met demand for several years and that the world’s stockpiles are being drawn down, (2) How sharply this fragile supply can be impacted by disasters at the world’s major uranium production facilities, such as a) the flooding of the McArthur River Mine in the spring of 2003, b) fires at Olympic Dam, c) the potential that Rossing, with an annual capacity of 4000 tonnes uranium might close by 2007, (3) the withdrawal of Tenex from the HEU (highly enriched uranium) feed agreement, and (4) the announcement by the Chinese of their intent to build 30 new nuclear reactors.

Jan 1, 2007

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By Richard L. Stein

INTRODUCTION Increasing a miner's chance of surviving a disaster requires advance planning for emergencies, adequate training of personnel, and the provision of proper survival equipment. It is extremely important that fires and toxic gases be detected early, and that warning systems such as stench, audible and visual alarms, and communications systems be provided to allow timely escape. However, situations do occur where timely warning is not provided and immediate escape is not possible, regardless of the precautions that are taken. Under such circumstances, a combination of new per¬sonal protective devices and old techniques can provide protection that is adequate to save a miner's life. SELF-RESCUE EQUIPMENT Self-rescuers are devices which provide a short-term supply of respirable air under the potentially lethal con¬ditions following a mine disaster. Functioning either as filtration devices for the elimination of carbon monoxide (CO) or as oxygen supplies, self-rescuers allow an endangered miner a limited amount of time in which to effect an escape or reach a place of temporary safety. Carbon-Monoxide Self-Rescuers For almost 50 years, filtration self-rescuers have protected miners' lives following explosions or fires. Designed to eliminate carbon monoxide from inhaled air, the first of these devices was approved in the 1920s and has evolved into the two units that are approved today-the Mine Safety Appliance (MSA) W-65 and the Draeger 810. Both of these units rely on the cata¬lytic conversion of very toxic carbon monoxide to rela¬tively safe levels of carbon dioxide (CO,). As shown in Figs. 1 and 2, both of these filtration self-rescuers operate in the same manner. On inhalation, the mine air passes through both coarse and fine filters that remove the dust, preventing the dust from coating the chemical beds or entering the miner's mouth. The air then passes over a drying agent that removes water vapor; this is required to prevent the water vapor from poisoning the catalyst. Subsequently, the dried air passes over the Hopcalite catalyst, where carbon monoxide is converted to carbon dioxide. Then, the air passes through a heat exchanger that reduces the temperature of the inhaled air. Finally, the air is inhaled by the user. Air exhaled by the user passes through the heat ex¬changer and exits the device through an expiratory valve. Both units of this type are subject to certain limita¬tions: 1) The units do not protect the user against oxygen¬deficient air; when air is inhaled through this type of self-rescuer, the device only removes the carbon mon¬oxide. If the mine air contains less than 15% oxygen, anoxia is inevitable. Symptoms of anoxia include dizzi¬ness, shortness of breath, quickened pulse, and deeper and more rapid respiration while the victim is at rest. During heavy exertion such as would be expected dur¬ ing escape efforts, a 15% oxygen level can cause loss of consciousness. 2) The units do not protect against excessive levels of carbon dioxide. Available data on carbon monoxide and carbon dioxide concentrations following explosions or fires are limited, but there are indications that the carbon monoxide concentration can rise to 2% and the carbon dioxide concentration can reach 5 or 6% of the mine air (by volume). In some situations, the in¬haled air could contain up to 6 or 7% carbon dioxide. At a carbon dioxide concentration higher than 2%, breathing patterns can be affected adversely. At a con¬centration of 6 or 7%, the effects include severe respira¬tory distress, with unconsciousness resulting from exer¬tion such as that needed for escape activities. 3) The units do not protect against high inhalation temperatures. The catalytic oxidation of carbon mon¬oxide to carbon dioxide is an exothermic reaction that evolves a large amount of heat. As the carbon monoxide concentration increases, the temperature of the inhaled air also increases. Available data show that above 1.5% carbon monoxide, the air inhaled through some self¬rescuers can be as high as 90°C (194°F). At those

Jan 1, 1982

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By S. G. McDowell

Automation techniques are used during the design stage of continuous miners to decrease the time required and ensure the accuracy of the design. This is followed by automated manufacturing processes to reduce manufacturing time and improve the quality and consistency of parts. Combined, the result is a more reliable machine that can provide ongoing production capability. With the use of automation to enhance operator effectiveness and monitor machine condition, the productivity of machines is also improved. Productivity of continuous miners doubled over a 10-year span (Fig. 1). Although this article focuses on the continuous miner, it should be recognized that production increases of the continuous miner would not be realized without increased capabilities throughout the rest of the mining system. There are several aspects of automation that have played a role in providing increased continuous miner productivity. Though some are considered indirect, they still had significant influence on the overall result. Basically, productivity increases are obtained by cutting, loading and transporting the coal at a maximum rate. In addition, these tasks must be consistent, with minimal downtime. Therefore, the miner had to improve in operational capability and reliability. Automation techniques used during machine design, manufacturing and operation have all played significant roles in achieving higher productivity.

Jan 1, 1991

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By S. D. Thompson

Since 1965 several researchers have independently developed computer models for designing gathering belt and surge bin capacities in underground coal mine belt systems. Table 1 summarizes the models applicable to U.S. mining systems. Most of the models, employ the Monte Carlo simulation technique. Basically, the belt loading at each loading point is randomly produced from probability distributions. In some cases, a combination of deterministic calculations and probability distributions are used to simulate the loading. Once the loading is simulated, it is systematically moved through the belt system in a deterministic fashion based on belt speeds, belt lengths, and storage bin discharge rates. The coal flowing from each loading point is tracked as it moves through the belt system. When the loading from tm different sources combines on a belt or in a surge bin, checks are made to determine if capacities have been exceeded. If capacities have been exceeded the amount of spillage is calculated. At the end of the simulated time period, the cumulative spill- age is used to evaluate the belt and surge bin capacities. Naturally, a considerable amount of spillage indicates the capacities are unacceptable. Acceptable capacities are generally indicated by minimal spillage. Numerous trial simulations are often necessary to find the acceptable capacities.

Jan 1, 1987

By G. I. Karydakis

Geothermal energy is an important energy asset which can play a significant role in providing energy resources to cover energy needs of a country while it can play a primary role in a particular region where it is abundant. Greece is especially rich in geothermal energy. The collision of Euroasiatic and African plates coupled with the strong tectonic tension, particularly in north Greece, resulted in the formation of important geothermal fields of low, medium and high enthalpy. These fields are in the Aegean islands, in central and east Macedonia, in Thrace and in central Greece. This work presents and analyzes information about the drilling activity for exploration and production of geothermal fields of low, medium and high enthalpy in Greece for the past thirty years. The number and type of wells drilled together with the spatial and the yearly distribution are given. Depth data has been analyzed according to the fluid temperatures and to the geological formations. Cost data are presented and analyzed for the total number of wells drilled giving also the cost per meter drilled.

Jan 1, 2006

By Huo Zuzhao

The main feature of caving methods is to draw ore from the overlying waste rock. Research on the movements of ore and waste plays a very important part in reducing ore loss and dilution and raising the economic benefits. This paper gives the basic theory of computer simulation of ore-draw, exposses the physical significance of mathematical model, puts forword a new formula of similarity characteristic value, brings forth a method of adjusting similarity, introduces the major functions of the simulation program and describes the ore draw control and stope parameter selection through computer simulation.

Jan 1, 1986

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By R. H. Kuhlman

The purpose of this paper is to describe the roles of cement and concrete in construction in general and, more specifically, as construction materials of the Southeast. For purpose of this discussion, the Southeast will include the geographic area composed. of the following 13 states: Alabama, Arkansas, Florida, Georgia, Kentucky, Louisiana, Mississippi, North Carolina, South Carolina, Tennessee, Texas, Virginia and West Virginia. In one sense, cement by itself is not a construction material. It is a finely ground manufactured mineral product, usually gray in color. Cement is mixed with water and sand, gravel, crushed stone, or other aggregate to form concrete, the rock-like substance that is the most widely used construction material in the world. Because cement is seldom used by itself for construction but is usually a component of concrete, there is no such thing. as a "cement" sidewalk, a "cement" highway, or "cement" building. Neither is "portland" a brand name. It is a generic term used to describe any cement that hardens in the presence of water and is made to standard specifications .. For all practical construction purposes, therefore, all cement is "portland." The name "port-land" was selected by the English inventor of the product in 1824 because concrete made with his product resembled natural building stone quarried on Portland, an English island. Although portland cement is not the final material which finds its way into completed construction, as the principal component of the most widely used construction material in the world, the location and process of its manufacture warrant some discussion

Jan 1, 1977