Search Documents

By M. Scaggs

"Respirable dust in underground coal mines has long been associated with lung diseases, and regular dust sampling is required for assessing occupational exposures. At present, respirable dust concentration and crystalline silica content are commonly determined, but considering recent and yet unexplained increases in the incidence of lung disease amongst miners in specific geographic regions, more information about specific dust characteristics is urgently needed. While particle-level dust analysis is ideal, it is impractical for large numbers of dust samples because it is both time and cost intensive. Thermogravimetric analysis (TGA), however, is an alternative option, which offers the ability to determine the total coal to mineral mass ratio in a dust sample – analogous to proximate analysis of bulk coal samples for determining ash content. Here, preliminary development of a TGA method for this purpose is presented. The method is being developed to evaluate dust collected on mixed cellulose ester (MCE) filters using approved permissible sampling equipment. INTRODUCTION Based on the particle size, airborne mine dust can be classified in three categories: inhalable dust (< 100 µm in size), thoracic dust (< 25 µm in size), and respirable dust (< 5 µm in size) (Ramani et al., 2003). The World Health Organization (WHO, 1999) defines inhalable dust particles as those which can be breathed into the nose and mouth, and thoracic dust particles as those which can penetrate airways of the head and enter the airways of the lung. On the other hand, respirable dust particles can penetrate beyond the terminal bronchioles into the gas-exchange regions (alveoli) of the lungs (WHO, 1999). Hlavay (1992) reported that the seriousness of the damage in the lungs and respiratory tract is based on amount of dust remaining in these organs, and the amount of dust depends on the extent of dust exposure, the size distribution of the dust particles, and the capability of the body for dust elimination. Inhalation of respirable coal dust by miners can cause a disabling and potentially fatal lung disease which is called coal worker’s pneumoconiosis (CWP). Silicosis is another fatal lung disease caused by inhalation of respirable silica dust. In CWP and silicosis, dust particles deposit in the lungs, damage the lung tissue, and ultimately cause scarring which cannot be reversed (Colinet, 2010). While overall incidence occupation-related lung disease amongst coal miners in the US has been declining for over 40 years, it appears that there has been a recent increase in specific locations in Central Appalachia (CDC, 2006; Pollock et al. 2010; Suarthana et al., 2011). Although this trend is yet unexplained, one theory is that particular dust characteristics in these locations may be a factor (Hassan and Lau; Page & Oraniscak 2002). For example, several studies have indicated that different coals may generate different amounts of respirable dust (e.g., see Page, 1993 and Litton and Page, 1994), and the surrounding geology may also play a role in terms of the types of dust particles generated. Although respirable dust concentration and crystalline silica content are commonly determined as part of regulatory compliance sampling, more information about specific dust characteristics (e.g., size, shape and composition) is urgently needed."

Jan 1, 2015

By D. T. Maiers, P. L. Wichlacz, P. A. Pryfogle, J. H. Wolfram

The effects of metal solution concentration, biomass density, length of exposure time, and pH were determined for biosorption of molybdenum (Mo) and chromium (Cr) by three organisms. Results indicate that it is possible to sorb Mo and Cr from dilute solutions. Differences were observed in the abilities of an organism to sorb Mo and Cr as well as among respective abilities of the three microorganisms. This suggests an inherent selectivity of the organism which may afford the means to control a sorption-based process. Results also indicate that the metal sorption abilities of these microorganisms depend on duration of exposure, biomass density, solution pH, and the metal concentration of the solution. Each of these parameters suggests an additional means of controlling the sorption process.

Jan 1, 1989

By John A. Wolfe

The concepts of sea floor spreading and plate tectonics provide more logical explanations of some geologic processes than were possible a few years ago. I plan to premise my discussion of the regional features of Philippine porphyry copper deposits on this tectonic basis, recognizing that parts of the picture can be explained in other ways, but in the belief that this is the best explanation of the whole. The sequence of events which results in the formation of Porphyry deposits (Figure 1) can be summarized as the result of collision of crustal plates, subduction of the oceanic plate, emplacement of a serpentine ultrabasic diapir, formation of a dioritic magma at depths of 300 to 500 km, rise of the magma to a sub crustal or intra-crustal chamber, eruption of andesitic volcanoes, emplacement of diorite or differentiation of the magma into more acidic products, multiple intrusion of hypabyssal rocks and hydro-

Jan 1, 1973

By G. H. Schnakenberg

In 1986, the US Bureau of Mines (USBM) embarked on a major research effort to develop technology that could substantially reduce worker exposure to face hazards by simply relocating the equipment operators to an area of relative safety. This reduced-exposure mining system (REMS) research effort enhances the USBM&apos;s ongoing health and safety efforts aimed at reducing and controlling dust and noise and reducing accidents through training and better mining practices. This paper reports on the progress made on the developing research and demonstrates the technologies required for the computer-assisted teleremote operation of continuous mining machines, haulage systems and roof bolting machines.

Jan 1, 1997

ICMM’s vision is ‘a viable mining, minerals and metals industry that is widely recognised as essential for modern living and a key contributor to sustainable development’. The ICMM Sustainable Development Framework provides the basis for achieving this vision by assisting the industry to improve its performance. Two years on from the first SDIMI conference, significant progress has been made in further developing and implementing the Framework. To fulfill their commitment to implement and report performance against the ten sustainable development principles in the Framework, ICMM’s corporate members have committed to report ‘in accordance’ with the GRI 2002 Sustainability Reporting Guidelines and the Mining and Metals Sector Supplement, developed by the GRI and ICMM. While much remains to be done, development of the Supplement and the commitment to reporting mark an important milestone for ICMM and the sector.

Jan 1, 2005

By James L. Poole

The gold and silver markets from the late 1960&apos;s to the present are reviewed and the outlook for these metals in the 1980&apos;s is presented. Included in this discussion is a summary of the basic supply and demand balance for gold and silver since the mid-1960&apos;s. an explanation of the price formation for the metals, some of the relationships between the prices of these metals and selected economic parameters, and how these factors affect the outlook.

Jan 1, 1981

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By A. M. Marabini, G. Belardi, V. Alesse, E. Spaziani

The objective of this investigation was to verify the effectiveness of commercial and synthetic depressing agents in a complex oxidized zinc mineral flotation flowsheet using sodium sulfides and amine. The flotation tests were run on a finely-disseminated calamine ore grading 16.96% Zn and containing smithsonite, hemimorphite, cerussite, calcite, quartz and iron oxide, present essentially in colloidal form. The reagents used in the testing can be grouped into four classes: guar, starch, celluloses and acrylic polymers having various degrees of substitution and molecular weights. The depressants exhibiting the greatest selectivity towards the gangue (considered as a whole) are tripolyphosphate, polycarboxylic acids, methylcarboxylate guars and ethyl hydroxylic starch. In the rougher stage, the Zn recovery ranged from 70% to 80%, and the Zn grade ranged from 27% to 29%. In the Zn-Fe2O3 separation, the compounds ensuring the most efficient separation are the tripolyphosphate and the polycarboxylic acids. In the Zn-SiO2 separation, the compounds that exhibit the best separation efficiency are tripolyphosphate and guar of methylcarboxylic sodium salt. In the case of the Zn-Ca separation, methyl-carboxylic guar exerts the best depressing effect and does not adversely affect the Zn recovery. The separation provided by ethyl hydroxylic guar is also good, although not as good as the preceding reagent. Regarding the Zn-Al separation, the tripolyphosphate, the celluloses and the carboxylate guars are the best depressants. A hypothesis is advanced to interpret the depressing action of the most effective reagents.

Jan 1, 1995

By C. P. Lazzara, R. W. Pro, A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effectiveness of automatic water sprinkler systems in the extinguishment of incipient conveyor belt fires under ventilated conditions. Large-scale experiments were conducted using a double strand conveyor belt configuration. Standard response, pendent-type sprinklers, with activation temperatures of 100°C, were installed above and between the two strands of belting, in accordance with Federal standards for sprinkler system installations in belt drive areas. Experiments at airflows of 1.1 and 4.6 m/s showed that the sprinklers activated later, the peak heat release rate was larger, and more betting was consumed at the higher airflow. In experiments with 74°C, fast response, directional sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of bett consumed was slightly higher at the lower airflow. Experiments were also conducted with 100 °C, standard pendent sprinklers installed above the top belt, in accordance with the National Fire Protection Association (NFPA) Standard 123 for sprinkler system installations in conveyor belt drive areas in underground coal mines. In these experiments, the heat release rate and amount of betting consumed was larger at the higher airflow.

Jan 1, 1995

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By W. H. A. Timm

Lake Dufault Mines, Limited, is located ten miles north of Noranda, Quebec. Following discovery of a copper-zinc orebody late in 1961, metallurgical investigations of diamond drill core were conducted by Lakefield Research Limited during 1962 and 1963. These were followed by pilot-plant tests in May and June of 1964, utilizing underground development ore. Milling operations commenced on August 16, 1964, and reached rated capacity of 1,300 tons per day by October 1, 1964 (Figure 1). Since that time, tonnage was gradually increased to a maximum of 1,400 tons per day and since January 1, 1968, gradually decreased to the present rate of 1,100 tons per day due to an increase in the hardness of the ore. The ore milled from start-up until January, 1968, was mainly massive sulphides, consisting of a complex mixture of iron, copper, zinc and minor amounts of lead sulphides with important associated values in gold, silver and cadmium (aver- age specific gravity 3.8). From January, 1968, until the present, the ore being processed is described geologically as a boxwork of sulphide stringers of chalcopyrite, pyrite and pyrrhotite and some local dissemination in siliceous rhyolite (average specific gravity 2.9) supplemented by the massive copper-zinc ore. The limited size of the orebody and the mining method employed (open stoping by blasthole and slash and bench methods) would have made grade control from the mine difficult and expensive. It was decided to try to cope with grade variations in the mill. The resulting rapid and wide swings in mill heads, hardness and specific gravity have presented many and varied challenges for the mill personnel.

Jan 1, 1970

By T. Gouri Charan, G. V. Rao

A spherical agglomeration process for the separation of scheelite fines of less than 30 µm in very low concentration of 0.04% WO3 in a binary mixture with quartz fines of less than 30 pm has been described. A concentrate containing 14% WO, with more than 90% recoveries could be achieved by means of anionic sodium sulfo succinate collector at pH 3.5 and also with commonly used anionic sodium oleate at pH 10.5 as per the conceptual flowsheet suggested. Such a process is envisaged as commercial potential for the recovery of fine-grained scheelite present in the tailings of gold plants as found in India.

Jan 1, 1991

By B. J. Scheiner

The presence of organic materials in gold ores cyanidation. The presence of organic materials interferes with gold extraction by The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95 pct. This paper by the Bureau of Mines, U.S. Department of the Interior, discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By J. Winterton

Cripple Creek and Victor Gold Mining Co. is developing a full-scale pad injection program as part of the overall operational plan for the Valley Leach Facility. As part of the development process the mechanics of the injection methodology are evaluated in the context of physical injection measurements, outcome from geophysical monitoring, and gold leaching theory. The results indicate that hydraulic fracturing analogies advanced heretofore do not accurately describe injection phenomena in unconsolidated and noncohesive material typical of leach pads. A new interpretation is presented and extended to define operational strategies for maximizing gold production.

Feb 27, 2013

By Randy Sandrik

Sampling has evolved at two large underground limestone mines as conditions and product requirements have grown tougher over 100 years of mine life, requiring innovative techniques to insure delivery of high purity limestone. Sampling insures delivery of consistent product to customers at the lowest possible cost. Statistical considerations have evolved from simple data collection to predictive and process capability analysis. Sample methods include borehole samples, face (using a proprietary face-sampling device), and total plant feed automatic, process, and final product sampling. Lessons learned, while keeping costs at historically low numbers, include the importance of geological models, exploration drilling density, face sampling, and blending of ore.

Jan 1, 2005

By R. L. Grayson, T. L. Dickinson, C. G. Anderson

Sponsored by the EPA, USGS, DOE, and NSF through the Committee on Earth Resources, the National Research Council’s Committee on Material Flows Accounting of Natural Resources, Products, and Residuals, created in August 2002, studied the value that material flows accounting, which can track the flow of a material from the time it is extracted to its ultimate disposal, may provide for making better integrated economic, social, and environmental policy decisions. This could be a crucial technology for the mining industry to incorporate. This paper will recount the statement of tasks, the study process, and the science-based conclusions and recommendations reached.

Jan 1, 2004

By W. Nazarewicz

The introduction of continuous papermaking in the early 1800&apos;s was the beginning of the industry as we know it today. Since that time, the majority of the paper produced has employed an acid process. However, in the mid 1960?s, European producers began a transition to an alkaline papermaking process. Early European mill conversions to alkaline papermaking begun in the 601s, accelerated during the 1970&apos;s influenced by the dramatically higher cost for OPEC energy as well as the high cost of fiber and imported filler clay.

Jan 1, 1986

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990