Search Documents

By M. Deul

For the first half of the 21st Century the USA will rely on the same mix of fuels as for the past 50 years: Petroleum will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in severe stress on gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging ‘piggy-back’ trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By Friedrich Steinhäusler

RADON SOURCES AND CONTROL MEASURES IN THE MINING ENVIRONMENT Most of the contamination of the mine atmosphere by radon 222 is due to radon emanating from solid or fractured ore surfaces of walls, roof and floor. Also radon gas emanates from broken ore either from storage in backfilled mined-out areas as applied in e.g. shrinkage stopping methods or from ore spillage along intake airways mainly due to the use of trackless haulage. To a lesser extent water itself can represent an additional source of radon, which emanates into air from open drainage ditches or seepages along intake airways. The contribution from water can be controlled effectively by isolating the water from the primary intake air system, e.g. by diverting the water through pipes and/or sealing of seepages by grouting. However, control of radon emanating from rock surfaces creates a major technical problem with significant impact on the economic aspects of mining operations, if adequate radiological conditions must be maintained. Basically this can be achieved by suppressing the emanation process itself, confining already emanated radon or by removal of radon from the mine atmosphere. Extensive research has been carried out on the rate of radon emanation as a function of barometric pressure changes (Pohl-Rüling and Pohl, 1969). It could be shown that the radon supply consists of a permanent and variable component. The former results from the surface of the rock and depends mainly on the emanating fraction of its radium 226 content; the latter originates from within the rocks and is a function of the suction effect of decreasing barometric pressure, rock porosity and fissures. The practical application of this barometric pump effect for depressing the rate of radon emanation, e.g. by pressurizing the mine atmosphere, is limited due to high costs for providing a sink for absorption of radon and air as well as lack of permeability in most uranium ore bodies (Schroeder et al., 1966). Mine air cleaning by removal of radon can be achieved with the use of cryogenic methods, chemical removal, adsorption into charcoal beds, use of a gas centrifuge or general ventilation techniques. Technical problems have so far prevented the application of any of these methods other than ventilation. It is common practice to use the age-of-air concept, i.e. fresh air is delivered to the worker as directly as possible and removed quickly afterwards thereby maintaining the air "young". Engineering principles for quantity distribution of air through underground working areas are straightforward for general mining situations where radon constitutes an environmental contamination problem. However, in cases of high uranium ore content this concept may result in high costs with regard to installation and energy requirements for effecting both frequent air changes as well as sufficient heating of the air in cold seasons. Taking into account that the investment in ventilation systems is a major cofactor for the overall ore production costs this can be a limiting and decisive component in the assessment of the economic feasibility of specific mining operations and mineral reserves in general. Effective control of the radon flux from the rock surface prevents the initial contamination of the mine air with radon directly at the source. A radon diffusion barrier for practical application in mining requirements should fulfill the following requirements: - reduction of radon emanation rate by at least an order of magnitude - high mechanical strength - ease of sealant application onto surface to be coated - water resistant - low fire hazard - resistant to temperature changes encountered in mines - high cost efficiency in relation to exposure reduction achieved (direct and indirect costs) - low degree of maintenance. In the past several materials have been tested as sealants for controlling the emanation of radon from surfaces of rock and building materials. Epoxy paints reduce radon emanation rate only by a factor of 2 to 6 (Auxier et al., 1974; Eichholz et al., 1980; Keith Consulting Engineers, 1980). Although it is possible to prevent the escape of more than 99 % of the radon to the environment with gel seals over 80 mm thick (Bedrosian et al., 1974), practical applicability is very limited. Multilayer coatings of epoxy resins with various additives require meticulous preparation and flawless application of seamless four-layer coatings in four days to impede radon diffusion (Culot et al., 1976), otherwise results from this method have not been totally satisfactory (Leung, 1978). Aluminium foil laminated with polyethylene and paper on each side is under test as radon barrier but results are not available yet (Ericson, 1980). However, this method has the inherent disadvantage that possible malfunctioning electrical installations can cause fire or electrical shock through the sealant. Polyurethane foam coatings have been used on stoppings as very effective sealants. It does, however, represent a potential danger of spontaneous ignition and it is expensive (Rock, 1975). Thus, there is still need for a material which has similar properties as outlined above. In the following results are reported from investigations on the suitability of various materials as radon diffusion barriers.

Jan 1, 1981

By B. Goertz

Since the turn of the century the mining industry in the United States has had a number of serious mine explosions, fires and ground fall disasters that have led to a major re-evaluation of mine communication and rescue practices. One of the hindrances of current underground communication technologies is the potential of lost or cut connections when a serious accident, such as an explosion, fire, inundation or major ground fall, takes place. The Mine Improvement and New Emergency Response Act of 2006 (MINER Act)1 mandated that each underground coal mine in the U.S. must provide for two-way wireless, post-accident communications between underground and surface personnel as well as electronic tracking of underground workers One area that has gained renewed attention in the mining sector is Through-The-Earth (TTE) communication. TTE technology has a major advantage in that transceiver devices can be carried by miners and set up quickly during an emergency, since they require no wire connection to the surface. TTE technology uses ultra-low frequency (1 to 4 kHz) electromagnetic waves, requiring relatively large wire loop antennas and highly sensitive receivers. The signal bandwidth is narrow and the permissible antenna currents in coal mines are restricted, which has led to limited usability of TTE technology in the past, as evidenced in research studies conducted by the U.S. Bureau of Mines in the 1970s. Yenchek (2012)2 pointed out that recent advances in receiver and signal processing technology have enabled voice and text communication capabilities and much improved sensitivity that offers new possibilities for TTE communication in mining applications. One company that has been developing such technology is Vital Alert Communication Inc. Vital Alert has been providing TTE communications since 2003 with a growing focus on emergency response and portable systems. The company?s Canary® Go System is one such product that looks to provide reliable communication capabilities in a portable, user friendly unit that can be utilized both for normal operation and mine rescue scenarios. Researchers at the Colorado School of Mines (CSM) have tested the Canary Go TTE communications system in the CSM Edgar Experimental Mine to determine signal propagation distances, signal quality and aspects of practical application.

Feb 23, 2014

By Gerald L. Finfinger, Michael A. Trevits

Since 1964, the US Bureau of Mines has been conducting a comprehensive program of research on the origin and control of coal bed gas. Several extensive databases have been developed during the work representing information from every major coal producing region in the United States. Gas content measurements have been made on 885 coal samples from 15 states representing 221 coal beds. Records indicate that the range of gas content varies from zero to over 640 ft3 per ton (20 cm3 per gm). During the conduct of the research program, several drilling and completion techniques have been developed or refined to divert and collect coal bed gas before it enters the mine environment. Such techniques include horizontal, cross-measure and vertical boreholes. Samples of gas collected from boreholes drilled under the program indicate that the primary gas constituent is methane which comprises 97 pct, the remaining hydrocarbons make up approximately 0.2 pct. Nitrogen and carbon dioxide account for the majority of the remaining gases at average concentrations of 1 pct each. Surveys have been made on the total daily gas emissions from underground coal mines. In fact, the most recent survey indicates that 180 mines had emissions in excess of 100 Mft3 per day (2.8 Mm3 per day). Furthermore, total mine emissions were in excess of 300 MMft3 per day (8493 Mm3 per day). An analysis of the data showed that there appears to be no relationship between in-place gas content and coal bed gas composition. Furthermore, no correlation was observed between in- place gas content and daily mine emissions. In a general sense, the higher the gas content the higher the relative gas emissions. Perhaps a more direct relationship would be observed if more complete emissions information (including gob gas borehole production) was available.

Jan 1, 1989

By Robert A. Haney, Scott G. Vail, Kenneth G. Fields

The Mine Safety and Health Administration, in cooperation with IMC Global Operations, Inc., conducted a joint study to determine the effectiveness of the technology currently in use at the mine to control diesel particulate exposures. IMC Global operates an underground potash mine using diesel-powered equipment to extract minerals. IMC uses a variety of technologies to control worker exposures to diesel particulate. These technologies include: ventilation, low sulfur fuel, oxidation catalytic converters (OCC), maintenance and work practices. The study was conducted over a two-week period, two shifts per day. During the first week (six shifts), baseline data on exposures and diesel particulate emissions were obtained. New OCC's were installed over the weekend on all equipment on the test section. During the second week (six shifts), data were collected to assess the effectiveness of the new OCC devices. In addition to exposure and diesel particulate emissions data, mine ventilation, engine exhaust temperatures and mine operational data were obtained. The primary means of determining diesel particulate concentrations was the respirable combustible dust (RCD) method. Gas concentrations carbon monoxide (CO), carbon dioxide (CO,), and nitrogen dioxide (NO,) were measured using passive dosimeter badges and gas bottles. Results of measurements of diesel particulate, gases, and air- flows were analyzed to determine the effectiveness of airflow and oxidation catalytic converters for controlling diesel particulate exposures. The use of oxidation catalytic converters resulted in reductions of both workers' exposures and diesel emissions.

Jan 1, 1997

By F. R. Corwin, M. S. King, R. W. Zimmerman

A model has been developed to relate the velocities of seismic waves in unconsolidated permafrost to the porosity and the extent of freezing. The permafrost is idealized as an assemblage of spherical quartz grains imbedded in a matrix which itself is composed of spherical water inclusions in ice. The theory of Kuster and Toksöaz, based on wave-scattering considerations, is used to determine the effective elastic moduli, and hence the wave speeds. The model predicts Vp and Vs to be decreasing functions of both the porosity and the water/ice ratio, and Vp/Vs to be an increasing function of these two parameters. The theory has been applied to laboratory measurements of shear and compressional wave velocities in thirty-three permafrost samples from different sites in the North American Arctic. Although no direct measurements were made of the extents of freezing in these samples, the data are consistent with the predictions of the model. The theory can be used to infer the extent of freezing of the water in the pore spaces, based on knowledge of the porosity and either of the two wave speeds.

Jan 1, 1986

By James R. Aggson, Verne E. Hooker

GENERAL CONSIDERATIONS The design of a mine or any underground opening in rock is similar to the design of any other structure, such as a building or a bridge, in one important way. This similarity lies in the fact that the stability of the structure is a function of the loads that will be applied during the structure's expected lifetime. In the case of an underground opening, the applied load is the product of the existing in situ stress field and the concentration of this field that is produced by the extraction of a load¬bearing material. Thus, a knowledge of the in situ stress field is considered a basic requirement in the design process and essential to the eventual stability of the underground structure (Duvall, 1976; Obert, 1972; Merrill and Peterson, 1961; Dahl and von Schonfeldt, 1976; Hedley and Wilson, 1975). The in situ stress field can be used along with the physical properties of the rock masses involved, the ge¬ometry of the various rock types, the geometry of the openings involved, and a failure criterion to evaluate structural stability of a planned mine by theoretical or numerical techniques. This same information can be used to investigate ground control problems in existing mines. In situ rock stress determinations can be separated into three categories: the determination of applied stress, also called the absolute or field stress; the deter¬mination of concentrations of the field stress near open¬ ings; and the determination of changes in rock stress as load-bearing material is removed. The applied stress field is more difficult to determine than are stress changes. Various instruments and techniques have been developed to determine applied rock stress and stress changes in rock. ABSOLUTE OR FIELD STRESSES Theoretical Considerations In the absence of actual measurements, it is often assumed that at any point, the vertical stress is equal to the weight of the overlying material. [ ] where S„ is vertical stress, S is average weight density of overburden rock, and h is depth from the surface. This is normally consistent with actual experience. The horizontal stresses are assumed to be equal and related to the vertical stress through the Poisson effect. [] where Sh is horizontal stress, S„ is vertical stress, and v is Poisson's ratio. The derivation of Eq. 2 is dependent on lateral con¬finement of the rock mass. An increasing amount of information is rapidly becoming available which indi¬cates that the in situ stress field at a particular location cannot simply be assumed to be a gravity-induced stress distribution in which the secondary principal stresses in the horizontal plane are due to confinement and Pois¬son's effect. Rather they can be a complex function of gravity loading, regional stresses, structural features, ex¬cavation geometries, and variations in surface and/or possibly basement rock topography. Furthermore, the underground principal stress dis¬tribution is not necessarily vertical and horizontal as is often assumed. The deviation of the three-dimensional stress distribution from vertical and horizontal can be due to a combination of both topographic (Hooker, Bickel, and Aggson, 1972) and structural features.

Jan 1, 1982

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By B. G. McNish

Neutron Activator Laboratory Analyzer used for Rapid Analysis for Ore Blending, Stripping, and Mine Control BAUXITE is a rock and not a mineral. Since it is a rock, its mineral content varies depending upon the parent material, the topographic location of the deposit and the severity of the weathering and oxidation processes which produced it. At Bauxite, Arkansas the major mineralogical constituent of the bauxite is gibbsite with ~IL- purities of silica, iron oxide, and titania minerals. Minor amounts of other minerals are found. Chemical composition varies from 45% to 60% alumina, 5% to 25% silica, 1% to 15% ferric oxide, and 1% to 3% titania. The Arkansas bauxite region is located entirely within the north- central area of the West Gulf Coastal Plain near the northwestern boundary with the Interior Highlands. The region trends northeast-southwest and is about 42 kilometers long. It is divided into two districts; one in Saline County and the other in Pulaski County. The Saline District is the most important since it has produced most of the bauxite. This district is located at Bauxite, Arkansas and the deposits are found around the flanks of the Saline Dome. It is roughly square-shaped and is about 190 square kilometers in area. The source rock for the deposits is a Late Cretaceous, grey, nepheline syenite.

Jan 1, 1979

By T. Naarttijärvi

The Fabian ore body near Malmberget, Sweden, has an ore reserve of 5 Mt of predominately low grade iron ore, containing 40-55% Fe. Mining began in 1971 with a new method called slot block caving. About 2 Mt were mined, but poor fragmentation resulted in too much secondary blasting. This decreased mucking efficiency to such an extent that the method was abandoned after only 40% of the ore volume had been mined. At this stage a large stope (180 x 30 x 100 m) had been excavated. Although the exposed area was quite large, no caving action occurred in the hanging wall or in the ceiling. LKAB decided in 1977 to introduce sublevel stoping using 105-mm-diam holes. This was the first time large diameter holes were used underground in Sweden. The method had been evaluated in collaboration with the University of Luleå (LuH), the Swedish Detonic Research Foundation (SveDeFo), and the Swedish Mining Research Foundation.

Jan 3, 1982

By A. Davis, K. Nelson, C. Webb

Abandoned mines in parts of the Black Hills of South Dakota have the potential for acid rock drainage. For this work, ten sites were examined on Black Hills National Forest land or on private land whose drainage could affect Forest Service land. Water samples from all the sites had pH values less than 6. Results of analyses from water samples and rock samples showed a correlation between metals content and pH. Acid-base accounting was used to determine acid drainage potential of the sites. One site (King of the West Mine) had a high potential for acid generation; fortunately, little or no surface runoff leaves the mine site. Six sites appeared to have moderate potential, including the Minnesota Ridge Mine, which currently is being remediated. Three of the sites had low acid drainage potential.

Jan 1, 2004

By Brad C. Lewis

The coal mining industry has experienced a general trend toward longwall operations. An increasing percentage of underground coal is being mined by longwalls. And productivity in longwalls is likewise increasing. Operators of longwalls, however, have not yet reached a state of mining euphoria. Competitiveness within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. [Figures 1, 2 and 3] present trends in the industry. Longwall mines, as defined here, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Nonlongwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation. Annual percent increases in productivity appear to have peaked in the 1985-1987 time frame. This was due, in part, to implementation of technological advancements and improvements in management-labor relations. The results shown in [Fig. 3] aroused the author's curiosity. The first question was "Have technological advancements to increase productivity peaked?" It does not appear so.

Jan 1, 1990

By George H. K. Schenck

Decisions to develop deposits of calcareous materials for cement production are based largely on anticipated markets for heavy construction which utilizes concrete. The geologist should understand the fundamental factors that underlie such management decisions, so that his field work and reports will more effectively relate to the information requirements of managers in the cement industry. The paper examines the relationships that exist between exploration and development of calcareous raw materials for cement manufacture and changing factors in the marketing of cement. Continued overcapacity, improved technology, changing distribution patterns, ease of entry, economics of scale, and the nature of product demand are some of the characteristics of the cement industry that are basic to decisions regarding exploration programs and property development.

Jan 1, 1966

By Yong Kang, Renhuan Yu, Xinquan Liu, Liangying Chu, Qian Luo

In grinding-classification circuit, overgrinding, resulted from the fact that hydrophobic materials have higher density than hydrophilicmaterials, has been known as a knotty problem. By using of the air-sparged hydrocyclone (ASH) as classifier, in this pair, the overgrinding of hydrophobic materials has been successfully minimized. Compared with the conventional hydrocyclones, the ASH has less fine hydrophobic particles in the underflow and less large particles in the overflow, which shows that the recovery of fine hydrophobic particles in the overflow has been improved in the ASH.

Jan 1, 1995

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Cat 994 class) as primary loading equipment in open pit iron ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Data were gathered on loader selection rationale; operating and maintenance experience; and production, availability, and cost information. Brief time studies were conducted to indicate machine performance and utilization. The paper summarizes the field data and includes economic comparisons of wheel loaders versus cable shovels in an iron ore application.

Jan 1, 1996

By Chee Theng

"Keep calm and carry on mining. That has long been the conventional wisdom in the mining industry, a largely cyclical one that has weathered roller-coaster booms and busts. But in the years from 2002 to 2016, an unprecedented steep rise in commodities prices that lasted a decade and then took a sharp turn downward had made it hard for gold and silver miners to stay the course.“The last 15 years highlighted some of the structural and inherent challenges that our industry has, from product price uncertainty to long lead times to the capital intensity of our business,” said Mitchell Krebs, president and chief executive officer of Coeur Mining, who was the luncheon speaker at the American Exploration & Mining Association’s 122nd Annual Meeting held Dec. 5-9, 2016, in Reno, NV.Looking back, Krebs said, “We were given this enormous gift of a commodities super cycle, and the industry kind of blew the opportunity.” While gold prices rose 319 percent and silver prices rose more than 200 percent over the 2002 to 2016 period, the XAU index of 30 gold and silver mining companies’ stock prices went up by only 20 percent.Entering 2016, precious-metals prices have made a comeback, with gold rallying strongly from a six-year low at the start of the year. This time, the industry is ready. Companies are leaner and meaner, with lower costs, reduced debt and an increased focus on higher grades and quality ounces. Although opportunities were missed in the past, the industry has got its act together and is now well positioned to take advantage of a price upswing and even to show profits when prices fall, as they did in August 2016, pushed down by a strong dollar."

Feb 1, 2017

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011