Search Documents

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group's mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By M. C. Williams

As the flaws in the population balance model (PBM) comminution model are examined more deeply, further errors and problems were discovered. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalization assumption. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions.

Jan 1, 1993

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By S. Lin, Y. J. Wang

Fan stall is a notorious phenomenon of axial flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts on the stability of the ventilation system are very complicated and not well understood. Results from laboratory experiments indicated that, when a fan is working across its stall zone (i.e., the pronounced trough on the fan characteristic curve), some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a nonachievable quantity range of the branch, because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). This paper discusses these important characteristics of ventilation systems by using results from tests on laboratory tubing networks.

Jan 1, 1998

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By R. B. Berg

Montana sapphires were first discovered in alluvial deposits in the Helena area in 1865 and subsequently were discovered in other alluvial deposits in southwestern Montana and also in a lamprophyre dike at Yogo in central Montana. From about 1900 until the late 1930?s, when synthetic sapphire began to come into widespread industrial use, Montana sapphire mines produced large quantities mainly for watch bearings with lesser production for the gemstone market. The Yogo deposit is now mined for the gemstone market and two of the alluvial deposits are mined to produce sapphires for the fee-sieving of sapphire-bearing gravel and for the direct sale of gemstones. The generally pale-colored sapphires from the alluvial deposits in southwestern Montana are heated to enhance their colors whereas the generally blue sapphires from the Yogo deposit require no treatment. Markets for sapphires from both the alluvial deposits and the Yogo deposit are strong. In spite of reported historic production in excess of 70 tonnes, mineable resources appear to remain at most major deposits. Also abundant untested lamprophyre dikes in central Montana may host sapphires similar to those at the Yogo deposit.

Jan 1, 2009

By K. A. Natarajan

This paper deals with the various electro- and biochemical mechanisms involved in the bioleaching of multisulfide minerals such as those containing copper-lead-zinc and copper-nickel-iron. Galvanic series for sulfide minerals consisting of pyrite, chalcopyrite, galena, sphalerite, pentlundite, and pyrrhotite in an acid bacterial leaching system is illustrated, and the role of relative electrochemical activity on selective dissolution is discussed. Typical leaching results are shown to illustrate the practical applicability of galvanic effects in bioleaching of multisulfides. Attachment of Thiobacillus fewooxidans onto chalcopyrite and sphalerite mineral substrates is illustrated through scanning electron micrographs. The role of high-metal-tolerant, specially adapted strains in the leaching of multimetal concentrates is also outlined.

Jan 1, 1987

By Charles N. Speltz

The cost of transportation of industrial minerals frequently is higher than the cost of the product. When a mine, industrial-mineral plant, or customer is served by a single railroad, because of the lack of competition, that railroad may in- crease rates and/or reduce service so that the economics of that mine, plant, or customer are affected adversely. Transloading of industrial minerals from rail-to-truck or truck-to-rail to improve economics and sales of product is not a new concept. However, transloading to create competition and reduce freight costs or to improve service is a relatively new concept brought on by the recent mergers of many of the main-line railroads, both in the eastern and western United States. For example, in 1998, with completion of the Burlington Northern/Santa Fe (BNSF) and the Union Pacific/Southern Pacific mergers (UPSP), the western United States has only two main-line railroads. The industrial-mineral producer, to reduce the cost of transportation or increase the level of service, must evaluate potential transloading opportunities in light of higher prices and reduced service brought on by reduced railroad competition. This paper discusses industrial-mineral transloading and examines the case history of the Tucker Hill perlite project in southern Oregon. The Tucker Hill project is a classic study of industrial-minerals transloading where the project would have failed without the transloading.

Jan 1, 1999

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By Kenneth P. Neumann

The development of the Cyprus Thompson Creek Molybdenum Deposit near Challis, Idaho, began in 1967 when the first mining claims were staked on the intrusive rock outcrop. Exploration drilling continued for the next 14 years. During 1978, a decision was made to develop the deposit. In December, 1980, approval of the Environmental Impact Statement was received and construction of facilities and waste rock removal began. By the middle of 1983, 126 M metric tons of rock had been removed and all facilities were completed. The high work ethic of Cyprus Thompson Creek employees combined with innovation has made the mine one of the most efficient in the United States today.

Jan 1, 1983

By Ahmed I. A. Salama

This paper describes the development of computer density control for heavy media cyclone circuit at the Coal Research Laboratories of CANMET. The control objective is to reach and maintain the medium density set point in minimum time. A description of the mechanical components and instrumentation are presented. The control strategy and computer software are discussed. Testing and evaluation of the installed system are presented.

Jan 1, 1989

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By William Gleason

"On April 4, 2017, the largest earth-pressure-balance tunnel boring machine (TBM) ever built finally completed its 2.7-km (1.7-mile) journey beneath Seattle, WA, nearly four years after it began boring the SR-99 tunnel that will eventually replace Seattle’s Alaskan Way Viaduct.By now, readers of this publication are familiar with the ordeal that began on Dec. 6, 2016, when the machine overheated and shut down. Until that point, the TBM, named Bertha, had grabbed headlines for being the largest in the world with a 17-m (57.6-ft) diameter face. But after the incident that stopped the progress, the headlines suddenly stopped focusing on the engineering marvel of the tunnel project and began asking what went wrong. Just 300 m (1,000 ft) into the tunneling journey the machine was stuck, unable to move forward and impossible to retract.The project’s contractors, Seattle Tunnel Partners,(STP JV) – a design-build consortium comprised of Dragados - USA, Tutor Perini, say a 20-cm (8-in.) steel well-casing buried in the path of the machine caused the problems that halted the TBM. The Washington State Department of Transportation (WSDOT) disagrees, and the issue over who ultimately pays for the repairs is now with the courts.Eventually, engineers determined the best way to get Bertha back to work was to dig a 36-m (120-ft), deep concrete lined shaft pit in front of the machine and lift the 1.8-kt (2,000-st) cutterhead out for repairs. The repairs took two years but eventually the machine resumed mining in January 2016. In April 2017, the TBM finished building the tunnel, breaking through at the tunnel’s north end near Seattle’s Space Needle, with little to no ground surface movement measured on the entire alignment.While the cause of the TBM breakdown and who should pay for repairs was debated above ground, the work below ground continued. David Sowers, deputy program administrator, engineering and program management with WSDOT, told Mining Engineering during the 2017 Cutting Edge Conference in Seattle that in addition to the technical marvel that the tunnel became, the fact the parties involved were able to work through the unprecedented challenge is a great example of how to overcome challenges on massive projects."

Jan 12, 2017

By R. Hipsley, D. Arbonies, P. Dobak

South Arturo is a “Carlin-type”, breccia-hosted, oxide gold deposit located at the north end of the Carlin Trend. The discovery hole was drilled in July 2005 from mine dumps 1,000 feet south of the Dee open pit. Discovery hole (BD-72) encountered a cumulative 245 feet @ 0.056 opt Au beneath 850 feet of post mineral Tertiary Carlin Formation. Oxidation extends to depths greater than 2,000 feet in the deposit area. The deposit is presently in definition drilling stage with approximately 190,000 feet of drilling completed to date. A resource estimate is in progress. This paper will focus on the discovery and descriptive characteristics of the mineralization.

Jan 1, 2007

By E. A. Domínguez

Kaolin deposits of Patagonia (Argentina) were formed by ?in situ? alteration of volcaniclastic rocks or by erosion, transportation, and deposition of residual clays in small basins. The mineralogy, geochemistry, grain size distribution, and specific surface area of natural and washed kaolins were studied in order to point out the relationships with the ceramic process. Primary kaolins are coarse-grained, kaolinite+quartz±halloysite, with a very low specific surface area. Sedimentary clays are either kaolinitic?smectitic and very fine-grained or kaolinitic with a coarser particle size distribution. An interdependence between mineralogy, chemistry, particle size distribution, texture, surface activity and ceramic behavior was found. Plasticity is strictly dependent on surface activity and expandable clay minerals. Slip rheology is affected by soluble salts, smectite, and tubular halloysite. Kaolinite-halloysite play an opposite role versus smectite-I/S in slip casting and tile pressing. Kaolinite and quartz are beneficial for drying behavior while expandable clay minerals increase drying sensitivity. Firing behaviour is mainly affected by minor components supplying fluxing oxides.

Jan 1, 2010

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By E. S. Erickson, R. L. Stone

Introduction Evidence from blast furnace operations has indicated that using pellets with a higher ISO low temperature reducibility, a lower SiO2 content, and better resistance to low temperature degradation results in considerable coke savings and improved furnace operation. Although these benefits could not be directly related to reducibility differences alone, we believed there was sufficient evidence of the advantages in improved pellet reducibility to warrant laboratory investigation of ways and means to effect such improvements. It is well known that pellet reducibility can be significantly altered by changes in the basicity and the amount of non-iron oxide constituents. Past work (Friel and Erickson, 1980, 1982; Saeki et al., 1977; Thanning, 1974) has shown that with increased MgO contents, and at optimum CaO/S1O2 ratios, significant improvement in low temperature reducibility can be attained. The improved properties of such fluxed pellets have reportedly led to increased blast furnace efficiency and productivity (Saeki et al., 1977; Ilmoni, 1975). Less well known, however, is exactly what factors control reducibility in acid pellets. Because of this gap in knowledge, studies were undertaken of the factors affecting reducibility in acid pellets and to estimate their relative significances in modifying reduction behavior. This paper describes that part of our work done to determine the effect of bentonite on reduction behavior. Our approach was to first examine the effect of bentonite's presence on as pure an iron oxide as possible (i.e., a magnetite "superconcentrate" containing about 0.2% SiO2) so as to eliminate any gangue-binder interaction. The next step was to look at bentonite effects on concentrates with only limited amounts of gangue (containing about 1% SiO2), but of two different types, simple and complex silicates. Last, we

Jan 1, 1988