Search Documents

By R. B. Krog

Airflow patterns in longwall bleeder systems are affected by gob permeability and porosity and the condition of the gateroad entries after mining. As longwall panels are mined, areas of the caved zone and portions of the remaining gateroad entries become inaccessible, making direct ventilation measurement impossible. Mine operators are left to estimate direction and amount of airflow in the gob and the surrounding gateroads. The most readily available locations are where air enters the worked-out area, approved measurement point locations (MPLs) and/or evaluation points such as bleeder evaluation points, intake evaluation points, and the outer bleeder entry. Ventilation models (network or Computational Fluid Dynamics, CFD) can model the gob and the surrounding bleeder system but calibrating these models is difficult without field data. NIOSH installed a tube sampling system ahead of a longwall face and, as the face retreated, released a slug of tracer gas (SF6) to determine transportation times and flow rates in the inaccessible gateroads. The data was used to calibrate both network and CFD ventilation models for a longwall panel. Both model types were used to predict the airflow patterns in the gob and to determine the airflow rate from the longwall tailgate corner back to the bleeders.

Jan 1, 2011

By S. Chander

The fundamentals of flotation are reviewed with an objective to understand the limitations in predicting the performance of a sulfide mineral flotation system and in its scale-up from laboratory studies to plant practice. The difficulties can often be traced back to complex interactions between chemical and physical parameters and nonequilibrium effects. The physical and chemical changes that occur during the long sojourn of sulfide minerals that begins with mining, continues through crushing and grinding, and ends when they emerge from the flotation cell as a concentrate, are reviewed. The benefits of new techniques that have become available in recent years to identify and estimate the amount of surface species are discussed.

Jan 1, 1999

By N. R. Joshi, A. D. Agate

It is estimated that more than 80% of phosphate rock output in the world is used for fertilizer production. In India, there are only a few high-grade deposits of phosphate ores; therefore, most of the requirement for phosphatic fertilizers is satisfied with imported DAP (diamino phosphoric acid). Due to the drain on foreign exchange reserves, this import-dependent, essential commodity is in short supply in India and, therefore, is sparingly used by farmers. In addition, of the added phosphorus, normally 80% becomes unavailable to plants because phosphorus complexes are formed in soil, causing deleterious effects on plants. In our laboratory, this problem was tackled by using a bacterial consortium of phosphorus-solubilizing bacteria. It resulted in the speeding up of seed germination and increasing available phosphorus in the soil by 14%, over a period of 80 days. To use the low-grade deposits of phosphatic rocks available in India near Hirapur, Madhya Pradesh, India, which contain high amounts of iron, beneficiation through microbial means was used for phosphorus removal. Beneficiation was achieved partially through removal of extra iron by oxidizing ferrous iron from the ore by a Thiobacillus species after removal of impurities containing both silica and iron, instead of sieving and cleaning the ore using different techniques. This resulted in a cleaner ore, with nearly 70% of such impurities removed. The factors for beneficiation technique were standardized at the laboratory level and are being used for scaling up of the process. Thus, the beneficiation of phosphatic rock from Hirapur will be an important first step of phosphorus production in India.

Jan 1, 1999

By Edward J. Budill

One of the most dramatic innovations in the materials handling industry has been the development of stacker cranes and automated material handling systems. The stacker crane with its many capabilities and the development of reliable industrial automation controls have combined to produce dramatic achievements in an area once characterized by inefficiency lack of management attention, and capital investment. In many areas of application however, stacker cranes and high rise storage systems have been designed and installed with insufficient thought given to their integration into the overall operations of the plant or distribution facility. This paper will look at some new and interesting breakthroughs in the integration of stacker cranes and high rise storage systems into the total manufacturing plant system. In this paper we will refer to both bridge type stacker cranes and aisle stackers. The bridge type stacker crane was developed first and was initially developed with forks or other handling devices hoisted up and down a rigid or telescopic mast. This mast system was suspended from a trolley mounted on an overhead crane bridge. Today, the primary application of the bridge type stacker is in warehousing systems for handling basic metal products such as coils, bars, sheets and plates. There is no question that the bridge type stacker has achieved notable results in storage and handling of these commodities. However, a new area for stacker crane application has been developing which in many cases over-shadows the accomplishments in the storage area. This is the application of the bridge stacker as an integral part of the manufacturing processes, or in other terms the production applications of stacker cranes. The stacker crane has a number of attributes which makes these applications very important. First, the crane bridge provides the stable platform for the mounting of machinery which can accommodate the hoisting and lateral movement of large capacity loads. Today stacker cranes are being built with capacities of up to 30 - 40 tons. The bridge cranes can easily accomplish accommodation Of these large tonnages. Secondly, the mast system provides a stable platform for the mounting of a wide variety of manipulating devices which can be used for the placement of material into manufacturing processes, the extraction of this material from these processes, and movement to other points in the process area. These attributes combined with excellent operator control and safety have led to development of the stacker crane as a production tool.

Jan 1, 1973

By Louis W. Riggs

The primary concern in dealing with contractual arrangements for construction is getting the work completed satisfactorily, in the shortest time, and for the least expense for the owner--while assuring that all other parties associated with the contract make a reasonable profit for their effort. In our complex construction climate of today, achieving all of these is usually not possible. Somewhere between the beginning of design and the completion of the work, disagreements and delays arise which can destroy the best of intentions. Assuming that all parties associated with the contract are acting honorably and professionally, the disagreements generally arise through inappropriate contract types or through flawed contract documents. These flaws can be either sins of omission or commission, but we must find a way to lessen, if not completely eliminate, their impact. Disagreements and delays are directly related to the extra cost which the owner and the other involved parties must suffer. Usually the attorneys are the only ones who come out on the positive side. Inappropriate or defective contract documents can be the result of inadequate time for preparation and review, laziness in not searching out the proper terms and language, insufficient recognition of the proper assignment of risks, or just ignorance as to what is right and what is wrong for the particular project. They can also result from a client, particularly a public agency, providing rigid general conditions and format requirements with which the engineer is not allowed to tamper. Arguments

Jan 1, 1979

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By Carlos Viramontes Aldana

Mining in Mexico is one of its post traditional activities, whose influence in the development of important cities and communications has been decisive. Precious metals and, to some extent, copper and tin were known and used before the Colonial period, but from the sixteenth century to tie end of the nineteenth century, mining and metallurgical industries were concentrated in the precious metals, mainly silver. This silver was exported to Spain and other countries under the Spanish. Rule, Mexican peso was known world wide since the end of the sixteenth century and Mexico ranked as the first silver producer since the eighteenth century.

Jan 1, 1985

By R. J. Wahrer

In 1996, the Office of Surface Mining (OSM) and the U.S. Fish and Wildlife Service (FWS) completed an Endangered Species Act (ESA) programmatic Section 7 consultation. From the resultant Biological Opinion, it was found that coal mining operations conducted under federally approved state regulatory programs would not likely jeopardize the continuation of federally listed species nor result in the destruction or adverse modification of critical habitats. The requirements of the ESA and their integration into the SMCRA permitting process and the responsibilities of the regulatory agency, the FWS and the coal operator will be discussed. Guidance on the development of protection and enhancement plans will be provided and site-specific examples given.

Jan 1, 2003

By K. Whiting

In October 1993, the first two of a series of full scale passive biological treatment cells were constructed to treat mine drainage from the Burleigh Mine (located approximately 48 km west of Denver, Colorado in the Clear Creek/Central City Superfund Site). The two cells are each 19-21 m long, 10.7 m wide and 1.2 m deep. Each cell contains approximately 216 cubic meters of substrate (composted manure) and is designed to treat 60 L/min of mine flow. One cell is designed as an upflow reactor and the other cell is designed as a downflow reactor. The differences in flow hydraulics and treatment efficiencies will be tested in these two cell for approximately nine months before the remaining cells are built to treat all the discharge. The substrate material was selected based on a series of bench scale tests. During the tests, the amount of metals removed was determined. The design flow rate was based on a sulfide generation rate of 400 nanomoles of sulfide generated per cubic centimeter of substrate per day. Metal removal results for the first three months of operation of the two cells will be presented and compared to results of bench and pilot studies at other sites.

Jan 1, 1994

By P. R. Hervey

Quartz is the second most widely used electronic material, with approximately 3,000 tons of single crystals used each year. Virtually all of this material is synthetic; grown with a technique called hydrothermal growth. We will review the basics of hydrothermal growth, the feedstocks for these crystals, and the challenges to improving the growth process. We will also review the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 1999

By R. Bruce Tippin

because of the mineral's high monetary value and the spotty occurrence of free gold in the deposit. Setting up a plant sampling procedure by simply applying the usual statistical sampling theory was questionable. Two sampling concepts were considered in the sampling study: o a sufficient number of assays can be taken such that the average determined from these individual samples represents a known quantity of ore. o a sufficient weight of sample can be taken such that when assayed it represents a known quantity of ore. The test program included evaluation of sampling techniques, sample preparation and analytical methods. The overall sampling program is depicted in Figure 2.

Jan 1, 1985

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By Richard E. Gertsch

The recent upswing in mining coincided with increased environmental concern. These trends have significantly increased regulation, but have not always provided sound environmental protection. Throughout, mining has remained passive, reacting to initiatives from outside. The high road to environmental protection must be an active strategy. The mining industry must take the lead and develop an environmental program effective in price and protection. It must involve all levels of mining. The mining industry should be the real environmental activist. We have the most to gain by sound environmental protection and the most to lose if the environment decays.

Jan 1, 1991

By Erich U. Petersen

Chemical zoning studies of mineralization can be useful in guiding exploration efforts. They permit one to determine the limits of mineralization and to correlate mineralized intervals in drill holes. Fahlore minerals are well suited for zoning studies because they are common minerals found in a variety of deposits, exhibit chemical diversity, and record the chemical evolution of migrating hydrothermal fluids. Zoning information in the form of metal ratios preserved in fahlore minerals was used to determine ore body limits in the Orcopampa precious metal system, Peru, and to correlate between multiple ore horizons in a sediment hosted massive sulfide (SHMS) currently under investigation. The current generations of electron microprobes provide the most efficient, accurate and economic way to analyze the tens to hundreds of sample required to successfully describe and use zoning information at the mine scale.

Jan 1, 1991

By D. Y. Geng

Longwall mining is a relatively new mining method in the United States. Early trials in the eastern and central coal fields were not successful, mainly because, among others, the face supports did not have sufficient capacity. It was not until in the late 1960's, when the high- capacity self-advancing powered supports became available, that longwall mining was successfully reintroduced. Since then the number of mines employing the longwall method has been steadily increasing. It has reached approximately 7.5% in 1981. Currently longwall mining is used mainly in the Appalachian coal field. The seam depth ranges from 150 to 2500 ft. but mostly between 300 and 1400 ft. The seam thickness ranges from 32 to 144 inches with the majority between 40 and 100 inches. Nearly all longwall mining are in flat or nearly flat seams extracting in single slice, although one inclined and one thick seam longwall mining have been either operated or initiated in Colorado.

Jan 1, 1983

By N. Nemeth

The filter is an apparatus designed to hold the filter medium. At such a medium takes place the entire liquid-solid or gas-solid separation process. Hence, the medium is really the essence of filtration. Yet, the medium, an originally clean porous substance with trapped solids in it, is perhaps the most neglected part of filtration research. Basically three problems prevail at the medium: 1) Penetration of solids and their blinding of the medium and the influence of such blinding on the resistance to flow. ii) The behavior of the medium in long term repetitive filtration. iii) The filter effect phenomenon whereby the flow rate on filtering an apparently clear liquid through a medium decreases with time. This study undertakes to investigate these fundamental processes.

Jan 1, 1968

By J. Hilgers

Metal prices are often predicted by relying on time trend projections of various economic indicators or even the trend in price itself Thus, time is the underlying explanatory variable acting through at best, a limited selection of economic variables. The price prediction method described in this paper differs from this by analyzing hundreds of economic variables to develop a few principle components that automatically capture the fundamental changes in the economy and delete duplicate or irrelevant information. This leaves a few principle variables to describe a state-space representation of the economy which can then be used for prediction. Forecasts of the price of a metal are then made based on these principle variables.

Jan 1, 1995

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By W. K. Utt

This report discusses U.S. Bureau of Mines' research involving modem vehicle position determination techniques in surface mining. The applications would include haul trucks, power shovels, and drilling rigs. Accurate position determination of these vehicles in near real-time is expected to result in safer and more efficient mining operations. The requirements for a vehicle position monitoring and warning system were determined. After screening several concepts, the global positioning system (GPS) and a radar positioning system were selected for further evaluation. A state-of-the-art GPS receiver was taken to a surface mine to assess the feasibility of receiving the satellite signals. A state-of-the-art radar positioning system was evaluated with regard to accuracy.

Jan 1, 1995

By D. Kang

The adsorption behavior of silver in ammoniacal solutions on to activated carbon has been studied. The parameters affecting the adsorption of silver on to activated carbon included temperature, agitation speed, concentration of cations and anions as well as that of ammonia. It was found that the adsorption of silver from ammoniacal solutions was dependent upon the initial silver concentration in the solution and other factors. The recovery of silver from ammoniacal solutions was found to be not so effective as the case with gold reported earlier. The adsorption rate was relatively slow overall, despite a rather fast initial adsorption. The apparent activation energy for the adsorption was measured to be 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1998