Search Documents

By Charlie Sons

Pit and underground mine operators typically use a lot of big equipment tires. Just as typically, they spend a lot of money they shouldn't on these tires. That's because tire use and maintenance are not given enough attention. That often occurs because mine management and personnel do not know the basic facts of tire use and care. If a piece of large equipment is damaged or ruined, a good explanation better he forthcoming. A ruined tire is often just a shoulder shrug. But that sort of fatalistic acceptance can cost tens or hundreds of thousands of dollars a year extra for big equipment tires. That does not have to be. There are some basic tire considerations that, if followed, will extend tire life and lower tire costs. Most companies have the inevitable conflict between the production department, which resists any restrictions that may reduce productivity, and the maintenance department. Production success is based on meeting a schedule of yards moved, while maintenance success is based on availability and equipment cost. When production falls behind schedule and equipment speeds are increased, maintenance may soon find its tire costs rapidly increasing, unless everyone understands the tires' vulnerability to damage. Unless the production department understands the problem, or restraint is applied by top management, costs may become exorbitant. At one job site, tire costs alone exceeded $250,000, to move 55 dam3 (72 000 yd3) of dirt on an 11-km cycle. The operation temporarily caught up with its schedule, but tire costs and attendant downtime soon made this a not-for-profit exercise. Because an operator must always attempt to move payload at the lowest cost, there are cases when higher than normal tire costs must be accepted. For example, in pioneering work with tandem engine scrapers, steep grades shorten tire life to less than normal. But the steep grades make shorter haul cycles possible, yielding more trips per hour than alternative earth-moving methods.

Jan 1, 1982

By M. Paventi, M. J. Scoble, B. B. Mohanty

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1998

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By P. K. Mululi, T. M. Yegulalp

The number and type of trucks and shovels used are two important factors in determining the optimal design parameters of an open-pit mining system. The characteristics of the arrival and service-time distributions of the trucks determine the performance measures of a truck-shovel system when it is modeled as a closed queuing network. In all of the previous analytical queuing studies of truck-shovel systems, trucks are assumed to be identical with respect to their arrival and service-time distributions. This assumption, although desirable for reducing computational difficulties, causes either underestimation or overestimation of the performance measures, depending on the number and types of equipment used in the model. The relative error in performance measures could be significant when the number of different types of trucks and shovels is large. In this paper, an analytical method is proposed to model the truck-shovel system as a multiple-class closed queuing network. This approach provides the capability of estimating system performance measures for planning purposes when the truck fleet is not necessarily composed of identical trucks. An example of truck-shovel systems is presented to show how the incorporation of different types of trucks affects performance measures.

Jan 1, 1998

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

By C. G. Tester

Automatic tripper control systems can be reliable and as such are suitable for use in the mining industry. Proper application of fundamental engineering principles provides the means for the reliability. Some of the principles are: (1) Be sure the system designer designs a system that does the job operations people want done; (2) Use sound logic design practices to avoid internal electrical problems; (3) The design must be maintenance oriented; and (4) Use good quality components. I would like to discuss a tripper control installation at Kennecott Copper Corporation, Chino Mines Division, in Hurley, New Mexico, and how these principles apply to this tripper control system. First, however, I will expand on the principles to clarify just what is meant. First, "Be sure the system designer designs a system that does the job operations people want done.? Operator acceptance is often the key to the success or failure of an automatic control system. One of the best ways I know of to get operator acceptance is to give him a system that he wants. I don't mean to imply that if bad practices or procedures exist that they should be incorporated in the control system. I do think that many designers feel they haven't done their job if the control system doesn't do things drastically different than the old manual method. Good engineering principles dictate that the job should be done right and if the manual method was right it can very likely be right for the automatic method.

Jan 1, 1973

By K. Hanumantha Rao, K. S. E. Forssberg, H. R. Manouchehri

The fundamentals of electrical separation, the electrical properties of minerals, the principal methods used for charging minerals and their mechanisms, the effective factors controlling the acquisition of charges by minerals, the general configuration of commercial electric separators and the forces operating during electrical separation of minerals are reviewed and presented.

Jan 1, 2000

By John J. Stetler

The Companhia Vale do Rio Doce in Brazil operates one of the most extensive systems in the world for the mining, transportation, processing, pelletizing and shipping of high grade hematite iron ore and pellets. Current shipping of unbeneficiated, sized, high grade ore from its ports at Tubarão and Vitória is now at the rate of 17,500,000 metric tons annually. An increase in this annual rate is now under study. Using the technology and facilities of Lurgi (1) and Arthur G. McKee company CVRD undertook a program to process and pelletize two types of fines - "Blue Dust" and ?Itabira Fines?. Blue Dust is a high grade fine ore which was bypassed while mining the direct shipping ores and which, also, exists as a very large ore body called the Conceição Mine. Itabira Fines is a lower grade of fine ore which is comprised of in-situ fines and, also fines which are generated in sizing the direct shipping ores for a rigid specification market.

Jan 1, 1970

By D. H. Carlson, J. H. Johnson, C. F. Renders

Introduction Diesel-powered vehicles are used extensively in underground mines throughout North America. The bulk of the diesel vehicles found in underground mining operations are used for loading and ore haulage, as well as for transportation of personnel and supplies. Along with the advantages of using diesels underground is the disadvantage associated with diesel-tailpipe particulate-matter emissions (DPM). The concentration of DPM in the ambient air of US underground metal mines is not now regulated by the Federal Mine Safety and Health Administration (MSHA). However, recent studies have shown DPM to be mutagenic (National Institute of Occupational Safety and Health, 1988), and the American Conference of Governmental Industrial Hygienists (ACGIH) has recommended that the exposures of per¬sonnel to DPM be limited to an 8-hr time-weighted average concentration (threshold limit value or TLV) of 0.15 mg/m3 (Anon., 1995). The authors, while making measurements in a number of US underground mines that use diesel haulage equipment, found mine air DPM concentrations ranging from 0.2 to 2.36 Mg/M3 (McCawley and Cocalis, 1986; Watts et al., 1989; Cantrell et al., 1991; Haney, 1992; US Bureau of Mines, 1992; Watts, 1992; Watts et al., 1995). If the proposed DPM TLV were to be adopted as a permissible exposure limit (PEL) for US underground mines, the proposed limit of 0.15 mg/m3 PEL would be lower than any of the concentrations measured in the earlier studies and would represent more than a 15-fold reduction from the maximum 2.36 mg/m3 concentration. A 0.15 mg/m3 PEL would also represent a 4.5-fold reduction from the average 0.68 mg/m3 measured mine ambient air DPM concentration reported in this paper. Other diesel tailpipe emissions that are now regulated underground include carbon monoxide (CO), with a PEL of 50 ppm; nitrogen dioxide (NO,), with a PEL of 5 ppm; nitric oxide (NO), with a PEL of 25 ppm; and sulfur dioxide (SO,) with a PEL of 5 ppm. Because the concentrations of these gaseous pollutants and DPM are affected by the state-of-maintenance (Waytulonis,1992), it is important that a means be developed to measure emissions from engines that are now in service to determine when maintenance is needed. The current study was the result of an inquiry by mine¬maintenance personnel who had been receiving complaints about high concentrations of diesel soot (DPM) in mine headings from load-haul-dump (LHD) vehicle operators. Mine-maintenance personnel were searching for an objective test to determine if the diesel tailpipe particulate emitted was excessive. The mine was also evaluating electronically controlled, two-cycle, naturally aspirated, direct-injection diesel engines on some of their JCI (John-Clark Inc.) load-haul-dump (LHD) vehicles. These LHD vehicles were used to haul freshly blasted ore from mine headings to a feeder breaker. The feeder breaker breaks down the larger chunks and feeds the broken ore onto a conveyor. Michigan Technological University, in past studies, developed an emissions-measurement apparatus (EMA) ca¬pable of measuring diesel vehicle tailpipe pollutant concentrations (Chan et al., 1992; Chan et al., 1993; Carlson et al., 1994). At the time of the study reported here, most of the mine's LHD vehicles used a 12-cylinder, four-cycle, naturally aspirated prechamber diesel engine. The study was undertaken in cooperation with mine maintenance supervisors from late 1992 through July 1993. The objectives were to compare diesel exhaust emissions between the 6-cylinder, two-cycle, electronically controlled, direct-injected diesel engine and the 12-cylinder, four-cycle, prechamber diesel engine and to, then, use the data collected, in conjunction with mine ambient air measurements, to demonstrate the application of the "deterioration factor" (Chan et al., 1992), which is a measure of the state-of-maintenance of mine-vehicle engines that are now in service. The information would be used to identify vehicles that need maintenance to reduce emissions. The data reported here are unique in the sense that they combine underground diesel vehicle ambient and tailpipe

Jan 1, 1999

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source' of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

In 1992, the United States economy grew at a rate of 2%. The Gross Domestic Product rose to $5,946 billion. With 257 million people - 635,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose I 1 % to 1.2 million units. New car production rose 4% to 5.7 million units. Truck and bus production rose 20% to 4 million units. The rate of inflation was 3.5% and the prime rate of interest was 6.25%. The Producer Price Index (1982 =100) was relatively unchanged from 1991 as follows: fuels and related products and power 80, metals and metal products 119, chemicals and allied products 126 and nonmetallic mineral products 117. Energy Imports of crude and refined petroleum, costing $50 billion, rose 3% to 455 Mm3 (2.9 billion bbl). Domestic petroleum production fell 1 % to 582 Mm3 (3.5 billion bbl). Petroleum supplied about 41 % of US energy, natural gas 24% and coal 23%. Coal production, 60% from surface operations, rose 1 % to 914 Mt (1 billion st). About 78% was used to generate electricity and 3% was coked. Exports valued at $4 billion included 57 Mt (63 million st) of metallurgical coal and 39 Mt (43 million st) of steam coal. Ura¬nium mining, including recovery from phosphates, fell 18% to 3 kt (3300 st) U308.

Jan 1, 1993

By Haydn H. Murray

Kaolin is defined and described as an industrial mineral. In addition the types of deposits -primary and secondary are defined and the genesis of kaolin from feldspars and other minerals discussed. The major deposits of the world found in the United States, Great Britain, Brazil, and Czechoslovakia are described along with many of the minor kaolin deposits. Four areas which have very large deposits of kaolin could, with technological breakthroughs to reduce viscosity significantly, become important factors in supplying the world markets which are increasing year by year.

Jan 1, 1977

By Martin P. Corriveau

It is not news to anyone in the mining industry that federal action in the prevention and abatement of air pollution has seriously affected the industry both directly and indirectly. It is the purpose of this paper to review how the development of federal action is directly affecting the coal mining industry's number one customer, the fossil-fuel-fired steam generating power plants and, consequently, the industry itself indirectly. In essence, Public Law 84-159 of 1955 as amended by the Clean Air Act of 1963 and its revisions in 1967 and 1970 progressively tightened federal coordination and management of air pollution control programs throughout these United States. The Environ- mental Protection Agency (E.P.A.) set up to direct the programs was charged to establish National Air Quality Standards, Standards of Performance for New Stationary Sources, and National Emission Standards for Hazardous Air Pollutants.

Jan 1, 1973

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By J. W. Shuster

Test of trolley-diesel prime power is another step in the search to exploit the unused potential of electric wheel driven haulage trucks. The output of the present engine - a 700 horsepower diesel - is not adequate to exploit fully the 1200 horsepower potential of the two electric wheel drive motors. Power was supplied to a modified 100-ton haulage truck through a double wire trolley system. The vehicle was tested with various payloads on a 7% adverse grade haul road. More significant conclusions developed are: Power - Horsepower to propel the vehicle can he more than doubled to improve truck cycle time. Productivity - Trolley power up adverse grades can improve [producivity] rates from 18 to 36%, dependent upon haul road profile.

Jan 1, 1968

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6)tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of a longwall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

Jan 1, 2000

By J. D. Morgan

Demand for nonfuel minerals depends in large measure on economic activity, which rose in each quarter of 1985. However, despite 1.7 million new housing starts and a 7% increase in motor vehicle production, many domestic metal mining operations experienced continued difficulties as a result of import competition, greater use of newer engineered materials, emphasis on multi-unit housing, and downsizing of motor vehicles. Recognizing the continued difficulties of the domestic metal mining industry, many corporations made major efforts to retrench and rationalize - selling, closing, or spinning off less profitable operations, renegotiating labor contracts, and inviting increased participation by foreign firms. About 15% of US energy was imported in 1985. This included $52 billion worth of crude oil and refined products, adding significantly to the overall merchandise trade deficit of $149 billion. With the exception of a few large-bulk, low-value raw materials, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult US nonfuel minerals trade deficit totalled $17 billion. The US continued to rely on imports for many important strategic minerals in 1985 (see accompanying Table). Increased pressures for protection included major mineral products such as steel, ferroalloys, and copper. But President Reagan, in his Feb. 1986 "Economic Report to the Congress" stated: "Our international trade policy rests firmly on the foundation of free and open markets." He also stressed the need for fair trade and more open markets internationally. The National Critical Materials Council, created by law in the latter part of 1984, was activated in the latter part of 1985. Its first public hearing was held in January 1986. The Council is to review the nation's materials posture and advise the President on such matters. Compared with 1984, the value of US raw nonfuel mineral output rose 2%, to $24 billion. This supported the production of $244 billion worth of processed materials of mineral origin. Raw steel production - a major indicator of both material use and mineral production - fell 4% to 81 Mt (89 million st). Consequently, domestic iron ore production fell to 49 Mt (55 million st), about 97% pelletized. Iron ore imports fell 7% to 16 Mt (18 million st). Raw steelmaking capacity fell 4% to 117 Mt (129 million st). Pacts with 16 leading steel exporting nations have been negotiated in an effort to reduce import penetration of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 40% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production increased slightly to 49 kt (54,000 st). Mine shipments of tungsten, another mineral tied to steel production, also fell slightly to 1.1 kt (1200 st) of contained metal. Even the domestic aluminum smelting industry suffered reverses as high stocks and low prices reduced production 16% to 3.5 Mt (3.8 million st). Similarly, imports of bauxite fell 7% and alumina 10%. Production of magnesium metal fell 6% to 136 kt (150,000 st), while titanium metal production remained unchanged at 22 kt (24,000 st). Copper mine production was unchanged at 1.1 Mt (1.2 million st). Copper refinery production fell slightly to 1.1 Mt (1.2 million st). Lead mine production rose 24% to 400 kt (440,000 st). Zinc mine output was down 10%, to 225 kt (250,000 st). Refined lead production increased 28%, to 510 kt (560,000 st). Primary slab zinc production fell 5% to 240 kt (260,000 st).

Jan 5, 1986

By R. Mensah-Biney

The NC State University Minerals Research Laboratory (MRL) and Waste Reduction Partners (WRP) of the Land of Sky Regional Council joined efforts in 2000 to initiate a technically sound and practical program for the management of high-volume coal combustion by-products (CCBs) in North Carolina. The accumulation of CCBs from coal burning boilers throughout the state of North Carolina posed a substantial storage problem, and the area was overripe for an effective management program, which would be environmentally sustainable. In particular, the public utility generators had filled storage ponds on their properties, and the storage overload had grown to critical proportions. Much the same situation existed for paper mill biosolids, which were stored on site in landfill cells along with daily output of CCBs from the mill boilers. A conversion process via the patented pyro-process12 (US Patent No. 5,342,442) to produce synthetic light weight aggregates (LWA) from CCBs and paper mill sludge was conceived to process large quantities of both these waste materials. MRL and WRP initiated and formed a consortium that brought together academia, private industry and state agencies to evaluate the production of LWA by the pyro-process. The industry partners included representatives from the power companies, industrial ash generators, expediters for coal ash products, as well as concrete block manufacturers. It was important to welcome interested parties from not only the western North Carolina area and other parts of the state but also from neighboring states including Tennessee, South Carolina and Georgia. Membership of this consortium evolved during the intervening years to include the following participants and supporters: Progress Energy Carolinas; Duke Energy; Santee Cooper; Full Circle Solutions; Land-of-Sky Regional Council; NC Department of Pollution Prevention and Environmental Assistance; Ecusta Business Development Center; Blue Ridge Paper Products; Jackson Paper and Manufacturing Company; Miller Perlite; Appalachian Products; General Shale Brick; Metromont Materials; Small Business Technology Development Center of the University of North Carolina system and North Carolina State University The initial development program conducted at the Minerals Research Laboratory (MRL) was to formulate an acceptable LWA product, which fulfilled user specifications for light weight concrete block and structural concrete application. Support work and program coordination efforts were furnished by retired technical volunteers in WRP. The work advanced steadily, using proven technologies well established in the mineral industry, to generate a very satisfactory LWA. The consortium then concluded that a more comprehensive CCB conversion program would have more appeal for full scale manufacture and commercialization, if a variety of products from CCB separation were generated. This product assortment would include bottom ash, low carbon fly ash, recovered carbon of high purity, as well as the synthetic LWA. The bottom ash would serve the concrete block market, the fly ash was in demand for ready-mix concrete, and the high carbon product could be pelletized and used as a fuel for reburn or by the steel industry, and the LWA was a sought-after component for light weight concrete applications. After scouting all these potential markets and finding them to be viable, the consortium then inaugurated an integrated pilot plant program for the CCB separation and conversion. The plan was organized in three (3) parts: (1) Phase I ? bench scale evaluation studies (2) Phase II continuous pilot plant evaluation and (3) Phase III ? conceptual commercial plant design including marketing efforts and attraction of business entrepreneurs to build a full scale manufacturing plant. Phase II would serve to validate the process in a continuous mode and produce substantial quantities of products for preliminary marketing efforts and for demonstration-of-use purposes. The consortium agreed to the name, CAROLINA ASH PRODUCTS, (CAP), for the integrated pilot plant program. The products generated might be designated with the CAP label as: bottom ash would be named CAP Granules, low carbon fly ash would become CAP Ash, recovered high carbon product would be CAP Carbon, and LWA would have the name CAP Stone. Phase II of the program processed 20 tons (18 t) of ponded ash from Progress Energy storage at a rate of 600 lb (271 kg) of raw ash per hour with favorable results. PRELIMINARY STUDIES Prior to committing laboratory research and development effort as well as support and coordination activities to this program, it was necessary to determine (1) the level of need for a freshly launched CCB reutilization program in this state and (2) what degree of versatility was necessary for such a process. State agency records and a survey of recent boiler operations indicated that in the state of North Carolina at least 77 facilities manage CCBs from their boiler operations. Despite continuing development efforts in more eastern parts of the state, the use of CCBs for commercial applications has not increased to a level which alleviates the need to store vast quantities in private monofills on the generator?s property. More than 1.25 million tons (1.13 million t) of CCBs are landfilled in NC annually, with 300,000 tons (271,985 t) per year generated in western NC alone. Many different boiler types, which span both very old units and those that are modern and efficient, were to be found. These included stoker-fired units, pulverized coal boilers, slag-tap furnaces, and fluidized bed combustion boilers covering a range of sizes. Any systems designed to separate CCB components from all these sources and convert them to useful secondary products would need broad processing latitude and flexibility. Up to the present there has been a paucity of research done in the western part of the state to find productive alternatives to storage in landfills. With tipping fees in our largest landfill now approaching $40 per ton ($44 per t) and escalating transportation fees (about $200 per truckload up to 40 tons, traveling a distance of 25 miles), the problem has become urgent both economically and ecologically. A well-designed, integrated wet process for CCB separation into value-added products had much potential to be less expensive than landfilling as well as to provide saleable materials with acceptable profit margins. These preliminary investigations also revealed that other major waste streams, in particular paper mill sludge and municipal and animal waste biosolids were important candidates for priority attention. Since these biosolids could furnish the organic component of a synthetic LWA product, they could be consumed as part of the same program. This added interest value to a growing list of partners to support and participate in the program.

Jan 1, 2009

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011