Search Documents

By J. C. Draper

The Duquesne Light Company and GAI Consultants, Inc. conducted a demonstration program aimed at establishing permanent vegetative cover directly on acidic, deep coal mine refuse. Several plots were treated with formulas varying in soil amendment application rates and plant species. Periodic monitoring of refuse chemistry has indicated when maintenance applications of seed and soil amendments were required. To establish drainage control, the site had to be regraded. The most successful formula was applied to the entire site. Specific treatment for acidic spots has been initiated. Results of the program indicate that adequate permanent vegetation has been established.

Jan 1, 1983

By W. R. Boehme

The test work was done in two parts. In Part I, five 6 x 16 mesh activated coconut shell carbon samples made by four different manufacturers were evaluated as to their gold loading rate and total gold loading. The five carbon samples tested are not identified by manufacturer and are simply designated as Types A through E. Then from the carbons tested, a suitable highly active carbon was selected for subsequent studies on impurity effects upon loading, Part II. Test Procedures The procedures and tests descriptions are given for the ultimate gold carbon loading tests and the dynamic gold carbon loading tests.

Jan 1, 1983

By Richard J. Fantel

The U.S. Bureau of Mines performed engineering and economic analyses on 130 domestic phosphate mines and deposits, all containing demonstrated resources, of which 73 are in the Southeastern states of Florida and North Carolina, to determine the domestic availability of phosphate rock. Of the total domestic resources studied (6.4 billion tons of recoverable rock) over 60 percent is found in these two Southeastern states. At an estimated cost of $30 per ton, in January 1981 dollars, approximately 1 billion tons of rock is potentially recoverable from Southeastern deposits, increasing to 3 billion tons at $45. In addition, there is nearly 6 billion tons of recoverable rock at the inferred level (some presently unmineable) in Florida and Georgia.

Jan 1, 1983

By M. Howe

This is a study of the impact of cyanide from mining waste on riparian communities, primarily vegetation, near Whitewood Creek, down-stream from Homestake Gold Mine in Lead, South Dakota. Cyanide is used in gold processing and the effluent, until fairly recently, was discharged directly into Gold Run Creek which empties into Whitewood Creek. Vegetation, soil, and water were collected from four different sites over a six month period, and samples tested for cyanide concentration. Data indicate a relationship between cyanide in soil and its uptake by certain plants, also, that the Homestake cleanup effort has made the stream viable again.

Jan 1, 1983

By David B. Ashley

Risks in underground construction are often viewed as technical in nature; "running ground, " "squeezing ground" and "chimneys" are terms that appear in construction managers' nightmares, and occasionally in their underground projects. Financial consequences of these and other project risks are reviewed. Special attention is paid to sources of cost overruns. From this study a structure evolves for setting priorities for risk management actions; these actions can also be tested for impact and potential effectiveness. Finally, case study reviews of six underground projects indicate the "state of the practice" for financial risk management.

Jan 1, 1983

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By S. A. Shoop

Vibrations from thirty-seven blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations reported in the U.S. Bureau of Mines studies. Regulations based on USBM data could then be too conservative or lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1983

By Timothy N. Dunne, Joseph M. Gonzalez

This paper presents the case history of a comprehensive geotechnical investigation for the Crosstown Transport Facility, a 10,880 m long, 3.2 m diameter pressure tunnel proposed for construction in San Francisco, California. The proposed tunnel would be part of the City and County of San Francisco's Clean Water Program, and its purpose would be to convey stormwater and sewage from the east side of the City to the Pacific Ocean. Tunneling conditions were defined by surface geologic mapping, 94 exploratory borings, surface and borehole geophysics, aquifer testing, Goodman Jack testing, pressuremeter testing, and laboratory testing. Through the use of advanced coring techniques and a strictly controlled drilling fluid system, core recovery averaged 90 percent in the sheared and fractured rock of the Franciscan Formation. As a result, over 1,400 linear meters of rock core was recovered and is available for examination.

Jan 1, 1983

By Scott G. Britton

Until now, only the range of typical construction projects which are repeated over and over during the life of a coal mine have been discussed. This chapter looks at underground construction projects which occur only once or twice during the life of any given mine and are major construction projects in both time and cost. These projects usually require the services of an outside engineering and construction firm with hands- on experience in design installation. Because of this involvement with engineering and construction firms (EIC), the role of the construction engineer will change from one of actively de- signing and directing tasks to one of planning, inspection, and quality control. To reflect this role change in the discussions, the focus of this chapter will be changed to a broad overview of project participation. Of course, the projects under consideration in this chapter could easily fill more than one book on their design and installation. In addition, major construction projects are extremely site specific, requiring months of data collection about site geology, physical conditions, and potential excavation and construction requirements. Therefore, no attempt shall be made to discuss any detailed construction aspects as was done in earlier chapters. The purpose of this chapter is to present the fundamental concerns of a staff engineer or supervisor. This engineer does not make the decisions on choosing the EIC firm, but assists and interacts with their project team to accomplish the goals set forth by higher management. The construction topics to be reviewed fall into three main categories. The first category is highlighted by the installation of a main surge bin; the second is typified by the construction of an underground shop; and the third category encompasses special projects such as rotary dumps, crusher stations, and foremen's offices. These categories highlight the differences between degrees of mine responsibilities for project completion. The first topic is usually a turnkey project by an E/C firm for a given mine. The second topic represents the leading role of the mine in the project with a contractor as a support service or equipment supplier only. The third topic, special projects, is an example of a joint venture-between a contractor (leading partner) and mine management. These roles can change with any given project, but the changes in management responsibilities for the construction engineer can be nicely illustrated for the purposes of this text. The first step toward constructing major mine projects is to analyze the mine which influence their design. From the mine management standpoint, these parameters should reflect the role the mine will play in the project construction. In other words, what is the nature of the proposed mine environment and what are the material, labor, and time requirements needed to assist or direct the chosen engineering and construction firm? Answering these questions requires some basic project planning and cost estimation work. Here, only a general treatment is necessary, since detailed discussions of these topics will follow in Chapters 8 and 10. For those persons interested in the role of the EIC contractor, I suggest beginning by reviewing the article by Beall, "The Role of an Engineering and Construction Contractor," presented in the October 1980 issue of Mining Engineering magazine.

Jan 1, 1983

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983

By Vic Miller

Highly variable milling properties within a geologically complex porphyry copper deposit owned by Kennecott Corporation in Nevada made it necessary to estimate the copper recovery and concentrate grade in areas where actual test data was lacking. The estimation was made by first determining the relationships between the desired metallurgical properties and the ore's petrology (i.e. copper mineral type, rock type and copper grade). This relationship was then combined with the already estimated rock type, mineral type and copper grade data in the mineral block model to predict the milling properties.

Jan 1, 1983

By Bo R. Arvidson

High-energy product permanent-magnet materials of rare-earth cobalt alloys are being used in applications where space or weight are at a premium cost. New applications like friction-free bearings are also made possible. However, such magnet materials have not been commercially used in magnetic separators until now due to the high cost for the overall magnetic flux generation relative to commonly used ceramic magnets or AlNiCo magnets. The design of the new high-intensity permanent- magnet roll separator (PERMROLL) takes advantage of the unique properties of rare-earth cobalt magnets rather than just substituting for conventional magnet materials now in use for magnetic separators. Hence, the new generation of high-intensity magnetic-roll separators has some unusual characteristics that make known magnetic separation applications more economically attractive, and even expands the magnetic separation technology area to include applications for which no other feasible methods are presently known.

Jan 1, 1983

By J. C. Reid

Pre-cambrian scheelite deposits in Northeastern Brazil are widespread in a high grade metamorphic terrain. Previously these deposits had been interpreted as contact-metasomatic. In this paper, a volcanigenic model is invoked based on the volcanic setting (proximal to distal) and the absence of associated felsic intrusives and spatially associated metasomatic skarns. The tungsten was introduced into sediments by volcanic- exhalative processes and subsequently remobilized and further concentrated by heat and metamorphis fluids associated with high-grade metamorphism and migmitization. An alternative syngenetic - diagenetic model is discussed which requires the transport of tungsten by heteropoly acids and deposition of the tungsten as a function of Eh and Ph conditions and different clastic depositional environments. While such stratabound tungsten deposits are considered rare in North America, the hypotheses developed in this paper may open new areas for exploration.

Jan 1, 1983

By W. W. Atkinson

This paper describes some concepts developed in a geologic data recording system at the Victoria, Nevada breccia pipe-skarn copper mine. The recording system is not fundamentally new, but represents expansion of earlier ideas. The paper is based on the philosophy that a high quality geologic data base is necessary and that it should be complete, clear, standardized, neat, quantitative, and readily useable. It may be multi-colored or simply black and white. Graphic, descriptive and quantitative recording of data is essential. A format for core logging is presented and discussed and as well as a multiple overlay system for recording data gathered in surface mapping.

Jan 1, 1983

By Kenneth P. Neumann

The development of the Cyprus Thompson Creek Molybdenum Deposit near Challis, Idaho, began in 1967 when the first mining claims were staked on the intrusive rock outcrop. Exploration drilling continued for the next 14 years. During 1978, a decision was made to develop the deposit. In December, 1980, approval of the Environmental Impact Statement was received and construction of facilities and waste rock removal began. By the middle of 1983, 126 M metric tons of rock had been removed and all facilities were completed. The high work ethic of Cyprus Thompson Creek employees combined with innovation has made the mine one of the most efficient in the United States today.

Jan 1, 1983

By James F. Albus, Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area Applications in industrial minerals grinding include calcium carbonate, talc, barytes, mica, diatomaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc The basic principles can be extended to provide continuous drying and delivery of discrete par¬ticles from a wet process slurry The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques Mean particle sizes in the order of 1 micron are achievable from pre-milled feeds, or maintained from similar slurries in the drying mode Aspects of feed preparation and multi-stage processing are discussed

Jan 1, 1983

By David E. Thompson, Edward S. Plotkin

The Massachusetts Bay Transportation Authority (MBTA) Red Line Extension Northwest is nearing the final stages of construction. The 3. 1 mile extension of the Red Line from the existing Harvard Square Station in Cambridge, Massachusetts to Alewife Brook Parkway in Cambridge, includes a large, near surface, hard rock, rapid transit chamber at Porter Square in Cambridge (Figure 1).

Jan 1, 1983

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983

By D. Y. Geng

Longwall mining is a relatively new mining method in the United States. Early trials in the eastern and central coal fields were not successful, mainly because, among others, the face supports did not have sufficient capacity. It was not until in the late 1960's, when the high- capacity self-advancing powered supports became available, that longwall mining was successfully reintroduced. Since then the number of mines employing the longwall method has been steadily increasing. It has reached approximately 7.5% in 1981. Currently longwall mining is used mainly in the Appalachian coal field. The seam depth ranges from 150 to 2500 ft. but mostly between 300 and 1400 ft. The seam thickness ranges from 32 to 144 inches with the majority between 40 and 100 inches. Nearly all longwall mining are in flat or nearly flat seams extracting in single slice, although one inclined and one thick seam longwall mining have been either operated or initiated in Colorado.

Jan 1, 1983

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983