Search Documents

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By K. D. Luxbacher, J. T. Davis

"A wind tunnel was designed to examine air flow, heat transfer and layering near an active fire at a working face. This tunnel simulates an active entry in an underground coal mine including an attached cross-cut of similar dimensions. A steel rectangular duct 1 ft. (0.305 m) tall, 3 ft. (0.914 m) wide and 10 ft. (3.05 m) long composes the main body of the tunnel and represents a mine entry. Air flow is generated by an exhausting centrifugal fan attached to one end of the crosscut. This fan was sized to supply air velocities based on Froude scaling. A 6 in. (15.25 cm) propane burner is used to simulate fires of various heat release rates at the working face. Thermocouples are used to map heat layering in the tunnel. Ports are installed for the introduction of tracer gases into and from sampling the system. Barometric, differential pressure, and temperature sensors are also included to monitor environmental conditions. Details about the design and testing of the system are presented including an overview of how the tunnel was scaled to accurately represent fire and flow phenomena. Finally, the proposed use of the tunnel for better understanding of mine fire phenomena and prevention is given. INTRODUCTION Fires in underground mines have been a concern since the dawn of mining. While technological advancements, regulations and best practices have improved both fire detection and firefighting techniques, mine fires continue to represent high risk events. From 2006 through 2015, fires accounted for 1.06% of fatalities in underground coal mines and 0.85 percent of fatalities in all underground mines in the United States (U.S. Department of Labor, 2006 to 2015). In addition to the risk of loss of life, mine fires can cause millions of dollars in equipment damages and lost production revenue. Extensive research has been conducted on how fires occur and spread in underground mines. In addition to testing conducted by government agencies such as the Mine Safety and Health Administration (MSHA) and the National Institute for Safety and Health (NIOSH) (e.g.(Liming, 2006), researchers like Verakis and Dalzell (Verakis, 1988) and Lowndes, et. al. (Lowndes, 2004) have furthered this field by studying ignitions and propagation of conveyor belt fires. While the studies of belt fires in mines are extensive, studies focused on fires at the working face are few in number. The particularly confined space and limited access to a working face, coupled with less robust, temporary ventilation controls create a unique environment that warrants special attention. Separate from studies on mine fires, the use of tracer gases to characterize flow patterns in normal mining ventilation is well established. In 1982, Timko and Thimons (Timko, 1982) outlined current and future applications of sulfur hexafluoride (SF6). However, little experimentation has been conducted to study specifically how tracer gases might be used to evaluate active mine fires and the fires’ effect on the surrounding mine environment (e.g.(Lindsay, 2014). In order to better understand the dynamics of smoke layering from a fire in an enclosed space, a small-scale apparatus was designed to map smoke layering and to examine other aspects of fire behavior at a working face. In addition to studying smoke flow around an active fire, experiments will be conducted using tracer gases in order to determine how they might be used to evaluate an underground fire."

Jan 1, 2017

By Zhongxue Li, Shuang Gao, Zhixin Zhen, Yiqing Zhao, Xuan Qin

If not well-managed, a mine-tailings facility may become a major source of risks, endangering the community and environment, and damaging the reputation of the minerals industry regarding sustainability. Identifying, characterizing, and mitigating the hazards and risks associated with tailings facilities have been critical to the maintenance of community-safe and environmentally sound mine-tailings facilities. Herein, a complex network model for characterizing the hazards and risks associated with the lifecycle of tailings facilities is presented. In this approach, the hazards are modeled as vertices of the complex network, and the interactions among the hazards are modeled as edges of the complex network. The complex network for modeling the hazard and risk spreading of mine-tailings impoundments is analyzed and characterized by using network metrics such as the network density, geometrical characteristics, characteristic path length, network efficiency, and clustering coefficient. The degree distribution of the network obeys a power-law distribution, indicating that the network for characterizing the risk spreading associated with a tailings facility is scale-free. According to the results of calculations and existing research results, the network is ultrasmall-world. By analyzing the change of the global network efficiency under four kinds of different methods to remove network nodes and edges, network nodes with higher between centrality (BC) are identified as critical. The removal of those critical nodes helps mitigate risks associated with a tailings facility and reveals the vulnerabilities to BC attacks.

Jan 1, 2017

By Gustavo A. Aristizábal-H, Oscar J. Restrepo-B, J. Alejandro Delgado-J

"In Antioquia region of Colombia – South America most of extractive activity is developed as artisanal and small-scale level, exploiting different types of minerals resources but predominantly gold. This is not only an ancestral livelihood of hundreds of families in this region, but also their unique way of subsistence. However, that situation has not had a positive effect in the sustainable development of this territory because of several unsustainability factors mainly related to mercury use for gold extraction, the incorrect management of tailings and the informal way in which miners perform their activity. In 2010 Antioquia was the place with the highest contamination by mercury in the world with serious effects in ecosystems and health of habitants of this region (Veiga 2010) This paper presents a Socio-Technical Model focused on strengthening capabilities and social capital of artisanal and small-scale miners and its surrounding communities in Antioquia region. This is based on processes of evaluation, design and implementation of appropriate technologies to obtain “clean minerals” without using mercury and with a right management of tailings. In gold extraction it is about gravitational methods of concentration, which take advantage of high density of this element. These methods not only are cleaner but more profitable for miners. Notwithstanding its technical origins, the current model proposes a holistic framework that manages the elimination of mercury in mining not only as a technology transfer matter. Thus, more than formalization the strengthening process seeks to promote a business vision in miners and to develop productive chains in surrounding communities, this means to improve the skills of artisanal and small-scale miners to organize in a corporative way and to help surrounding communities to provide support and supply services to mining and even to other companies. Besides, the articulation with local institutions drives to reinforce their functions of control and accompaniment. In shorthand, this effort aims to empower local institutions, miners and surrounding communities in such a way they are able to face together their own development challenges in a sustainable way."

Jan 1, 2017

By N. K. Dumakor-Dupey, K. J. Bansah

"We made site visits to determine potential environmental issues caused by artisanal and small-scale mining (ASM) in the Tarkwa Mining Area (TMA) of Ghana. Activities of the diggers were observed to degrade vegetation, land and water. Improper handling of mercury was also identified as a major threat to people and ecosystem. Large abandoned pits and trenches posed fall traps to farmers, hunters and wildlife. We argue that lack of adequate monitoring and regulatory enforcement by Ghanaian authorities, together with inappropriate mining processes, probably due to lack of technical expertise are contributing factors to the environmental issues of artisanal and small-scale mining in the TMA. INTRODUCTION Environmental degradation caused by artisanal and small-scale mining (ASM) has been a major concern to many people and governments around the world. ASM is often associated with health, safety and environmental issues in communities where it is practiced (Kitula, 2006; Asiedu, 2013; Sousa et al., 2010). Some of the environmental issues that have been reported include land degradation, mercury contamination, cyanide release, and pollution of rivers/streams. These issues have been attributed to improper mining methods, inefficient technology, lack of technical training and environmental awareness, and lack of regulatory enforcement (Serfor-Armah et al., 2005; Bansah et al., 2016a; Hentschel et al., 2002). In Ghana, ASM typically occurs in rural communities, providing jobs to many people and contributing towards socioeconomic growth of the country (Banchirigah & Hilson, 2010; Bansah et al., 2016b; Osei-Kojo & Andrews, 2016). As a result of the environmental issues, many people have called on government to develop drastic measures to control ASM operations. It is in this regard that this paper examines potential environmental issues caused by ASM in the Tarkwa Mining Area in Ghana, and suggests mitigation measures to ensure environmental sustainability. ASM in the area comprises of registered (licensed) and unregistered (unlicensed) operations that adopt surface or underground mining methods to exploit gold-bearing materials. Surface operations typically involve clearing of vegetation, removal of overburden, excavation of mineral deposit, washing/grinding of excavated gravels and processing with mercury. Except grinding, washing and mercury recovery, underground operations are conducted below ground with limited impact on the surface. Alluvial mining is also commonly practiced in streams and along river banks. These activities can have devastating impact on biodiversity of the ecosystem. To achieve the objective for this study, field visits were made to ASM sites to observe operations and interact with diggers. Visits were also made to host communities of ASM and government officials to obtain their perspectives on ASM in relation to environmental impact. The study area (Tarkwa Mining Area) is located in the Western Region of Ghana (see Figure 1). It is endowed with natural resources such as gold and manganese. Hence, mining is the major economic activity in the area. ASM is widespread, with 15 registered operations and several unregistered mines. The environmental issues observed in the study have been grouped into three main categories: vegetation and land depletion; water quality and pollution issues; and mercury contamination issues."

Jan 1, 2017

By T. Gupta, T. Ghosh

"Rare Earth Elements (REEs) and their compounds are essential for numerous modern high tech applications such as renewable energy technologies, catalysts and defense applications. The destabilization of REE pricing owing to the global demand and supply deficit has forced many countries to re-evaluate the possibility of indigenous production of REEs. Cost effective and eco-friendly opportunities are being widely explored for extraction of REEs from non-conventional mineral sources such as coal and coal byproducts to stabilize the supply chain. Coal from Central Alaska (Healy Coal Mine) and Southern Alaska-Cook Inlet (Wishbone Hill) province have been found to possess elevated REE concentrations as compared to average world coal estimates. The objective of the study is to enrich the REEs in the fine size fraction (-75 Microns) from Healy and Wishbone Hill by froth flotation technique. A Box-Behnken design was applied for modeling and optimization of some operating variables on the flotation to maximize REE enrichment. The variables studies were frother dosage, pulp density (% Solids) and collector dosage. Experiments were carried out using a statistical design and the main and interaction effects on response variable was evaluated by analyzing 3D response surfaces. Based on the experimental results the optimum flotation conditions for maximum REE enrichment in the froth fraction was obtained at 4.2% Solids and 32.7 ppm of frother dosage for Healy coal sample and 10% Solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic equation for modelling and optimizing the response variable is found to be independent of collector dosage for both the coal samples. INTRODUCTION Alaskan coal deposits are distributed in three major coal provinces and are in Cretaceous and Tertiary rocks. The climate, vegetation type and sedimentation process has attributed to low sulfur content (averaging 0.3 percent) in Alaskan coals compared to other coal deposits found across the globe. In Central Alaska-Nenana and Southern Alaska-Cook Inlet coal province coal resources are contained in Tertiary rocks while bulk of the Coal resource in North Slope coal province is contained in Cretaceous and Tertiary coal bearing rocks [1]. Coals from Central Alaska- Nenana (Healy) and Southern Alaska-Cook Inlet province (Wishbone Hill) have been found to possess elevated concentrations of critical REEs as compared to the amounts present in world coals (Figure 1). The Wishbone Hill deposit is considered a relatively small deposit, with about 14 million tons of identified reserves, compared to Healy which has over 500 million tons identified [2]. The REE concentrations up to 286 ppm and 524 ppm on ash basis have been reported by Gupta et al. in 2016 with elevated concentrations Ce, La, Y and Nd which are expressed to be of critical importance by US Department of Energy. Accordingly, the two coal samples possess the potential to be used as a REE resource in the near future under favorable socio-economic and geo-political scenarios. [3, 4]"

Jan 1, 2017

By M. Ge, C. Mborah

"The acoustic emission/microseismic monitoring (AE/MS) technique has widely been used in the mining environment for the monitoring of rock mass stability. A successful implementation of the method is hinged on being able to accurately determine the P- or S-wave arrival which is then used in the determination of the source of an event. Determination of the arrival phase is usually performed visually by a human expert. However, the mining environment is characterized by high noise levels and different noise types of varying intensities. Therefore, performing manual phase picking on time series data acquired from the AE/MS monitoring system can sometimes be tedious and time consuming if not impossible. In this paper, a proposal for improving manual P-wave phase arrival picks is discussed. The method involves the filtering of the AE/MS data using a stationary discrete wavelet transform (SDWT) method. After filtering, appropriate scales/levels of the multi-level decomposition process are then selected for further processing. The first step in the picking process after filtering, requires the computation of the signal power and the root mean square (RMS) using the signal amplitudes at each scale. The preliminary P-phase arrival time is picked using the results of the calculated power and RMS values respectively. The calculated RMS values are then superimposed on the calculated power values to determine the final arrival picks. If the arrival time picks obtained by both methods coincide or are within 5 to 10 sample points, the pick is considered reliable. The accuracy of the method was verified using AE/MS data from two datasets obtained from two separate underground mines. The results of the study showed that the picking method is reliable and robust. Based on the data studied, it can be concluded that the method will help reduce the time usually spent in processing AE/MS data from mines. INTRODUCTION A successful identification and location of the source of acoustic emission/microseismic (AE/MS) events is mainly dependent on the onset time of the P-wave phase. In many seismic networks, initial picks are performed by picking algorithms followed by manual picks by human experts. If the waveform signal-to-noise ratio (SNR) is low, the P-wave onset time picks by the human expert is generally reliable and accurate [1]. However, for waveforms with high SNR, picking of the P-wave onset could be a major challenge. Also, due to the volume of data acquired daily, manual processing could be stressful and time consuming [2]. These challenges continue to provide motivation for alternative means of providing reliable and efficient ways of improving manual phase picking. The AE/MS technique has been an intergral part of safety monitoring in mines [3] due to its capacity to identify zones of instability in a monitoring area. To obtain an accurate source of an AE/MS event however depends on the quality of the data used for P-wave phase picking [4, 5]. AE/MS data from mines are generally contaminated with excessive background noise generated by the different mining operations. The AE/MS signals of interest are mostly buried in background noise which makes it difficult to pick the P-wave phase arrivals [4]. Processing AE/MS data acquired in noisy environment remains a major challenge due to the weak nature of AE/MS signals [6]. As noted by [4] most of the data recorded in the mine environment are mainly due to events not related to AE/MS events of interest. The complexity of data in this type of environment makes the detection and picking of P-wave arrival by human experts a very difficult task."

Jan 1, 2017

By Z. Jin, D. DePaoli, P. Zhang

"Phosphate beneficiation in Florida generates more than one tonne of phosphatic clay, or slime, per tonne of phosphate rock produced. Since the start of the practice of large-scale washing and desliming for phosphate beneficiation, more than 2 Gt of slime has accumulated, containing approximately 600 Mt of phosphate rock, 600 kt of rare earth elements (REEs) and 80 million kilograms of uranium. The recovery of these valuable elements from the phosphatic clay is one of the most challenging endeavors in mineral processing, because the clay is extremely dilute, with an average solids concentration of 3 percent, and fine in size, with more than 50 percent having particle size smaller than 2 µm, and it contains nearly 50 percent clay minerals as well as large amounts of magnesium, iron and aluminum. With industry support and under funding from the Critical Materials Institute, the Florida Industrial and Phosphate Research Institute in conjunction with the Oak Ridge National Laboratory undertook the task to recover phosphorus, rare earths and uranium from Florida phosphatic clay. This paper presents the results from the preliminary testing of two approaches. The first approach involves three-stage cycloning using cyclones with diameters of 12.4 cm (5 in.), 5.08 cm (2 in.) and 2.54 cm (1 in.), respectively, to remove clay minerals followed by flotation and leaching. The second approach is a two-step leaching process. In the first step, selective leaching was conducted to remove magnesium, thus allowing the production of phosphoric acid suitable for the manufacture of diammonium phosphate (DAP) in the second leaching step. The results showed that multistage cycloning with small cyclones is necessary to remove clay minerals. Selective leaching at about pH 3.2 using sulfuric acid was found to be effective for removing more than 80 percent of magnesium from the feed with minimal loss of phosphorus.IntroductionFlorida phosphate ore, or “matrix,” as it is called locally, contains three different mineral groups that have to be separated from each other: (1) phosphate minerals, (2) clay minerals and (3) quartz, or sand. As mined, the phosphate and sand particles are embedded in compacted mud, or clay-balls. Before separation can begin, all of the particles must be liberated from the matrix of mud. The very first unit operation in the beneficiation process is to disaggregate the various particles. This actually starts while the matrix is flowing through the multimile pipeline from the mine to the beneficiation plant. While in the pipeline, the matrix is exposed to shear forces as it passes through the various centrifugal pumps along the pipeline. These intense shear forces cause a significant percentage of the sand and phosphate particles to be liberated from the clay-balls by the time they arrive at the plant. Once they reach the plant, the first goal is to finish disaggregating the clay, and follow that by making a size separation at 1 mm. This processing is conducted in the washer, consisting of a large rotating trammel screen and a few stages of log washer, screens and hydrocyclones. In all of the currently operating beneficiation plants, the washer is a large structure that receives the matrix, screens it and then discharges a pebble phosphate product sized larger than 1.0 mm and a slurry of liberated clay, sand and phosphate particles that are smaller than 1.0 mm."

Jan 1, 2017

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By Zhe Liu, Liping Xiao, Jichi Bai, Xuefei Luan

"In order to study the removal efficiency of Cu2+ from acid mine drainage by prepared bentonite-steel slag composite particles, adsorption experiment was carried out. The composite particles were characterized by X-ray Diffraction analysis technique (XRD), Scanning Electron Microscopy (SEM) and Fourier Transform Infrared spectrometer (FTIR). The results show that: the composite particles can release alkali to neutralize the acid of acid mine drainage; the adsorption and chemical precipitation of Cu2+ occurred in the whole reaction process; the removal amount of composite particles on Cu2+ was 9.88 mg/g when the reaction reached equilibrium; the FTIR spectra revealed the existence of surface complexation; the SEM micrographs suggested that the composite particles would continue to adsorb and coagulate Cu2+ after the composite particles surface adsorbing Cu2+ and forming precipitate, namely, there was synergistic reaction of adsorption and coagulation; the XRD patterns further showed the existence of cation exchange and revealed that the states of Cu2+ in the surface of the composite particles was Cu-Si-O mineral phase and CuO(Cu(OH)2) polymerization precipitation. The bentonite-steel slag composite particles which can play a role of adsorption-coagulation synergism are excellent multifunctional green environmental mineral materials to treat acid mine drainage containing heavy metal ions.Introduction It is reported (Zuo and He 2013) that with the rapid development of industry, the world demand for mineral resources is increasing, while the problem of mine environmental pollution is becoming more and more serious due to the large amount of mining. The pollution of mine wastewater has become a global problem, in which acid mine drainage (AMD) is one of the most serious waste water. It is also reported (Cong and Zhao 2003) that acid mine drainage containing high concentrations of heavy metals and having low pH value, causing serious negative influence to the mining production and ecological environment. Acid mine drainage is one of the most serious environmental pollution to the mining industry. In recent years, it has been widely concerned by scholars at home and abroad."

Jan 1, 2017

By N. Duru

"Gravity concentration is still a challenging area in the mineral industry. This is mainly because of the fine size valuable mineral losses to the tailings during its application. But the recent developments in centrifugal separation methods and their mutual application with conventional separation techniques has increased mineral recoveries. In this paper, field application of conventional gravity separation methods with the combination of 2” diameter hydrocyclone cluster unit and a multi gravity separator (MGS) was discussed. Additionally, particle size distribution and chromite content of the plant streams is presented and initial laboratory test results were compared with the actual plant data throughout the paper. As expected, field data showed derivations from the laboratory tests but the combination of MGS and conventional gravity separation techniques resulted in gravity separation of -0.1 mm chromite particles. INTRODUCTION The purpose of this mineral processing plant project was to investigate the possibility of upgrading chromite ore from 12% to 48% Cr2O3 and having final tailings assay as 2% Cr2O3. For this reason, initially a set of laboratory gravity separation studies were conducted to evaluate the performance of combination of 2” diameter hydrocyclone cluster and multigravity separator. After obtaining successful results from the laboratory work, a feasibility study was initiated. Economical results of the feasibility study showed that an achievable high net present and return on investment values. Following the investment decision; engineering, equipment procurement, construction of the processing plant was completed in eighteen months. This paper focuses on the initial laboratory test work results, operational data of the 2” diameter hydrocyclones and MGS units; resulted chromite recoveries. Processed ore has the chromite associated with serpentine and olivine minerals. The chromite particles are generally in round shapes with sizes between 50 µm to 1600 µm and average size of 450 µm. The microscope images of the chromite and associated formations are presented on Figure 1.Chromite is formed in mixture with iron oxides, with varying amounts of magnesium, aluminum. The average chemical composition of the representative drill core samples of the ore deposit is given on Table 1."

Jan 1, 2017

By D. Yokom, T. Katsabanis, E. Tremblay

"The mining industry has always faced the problems of replacing retired mining professionals, retaining their knowledge, continuously developing the skills of local talent and employing under-represented groups. In expansionary scenarios the industry faces the additional challenge of increasing available talent. New talent has traditionally come from current mining programs; however, these programs have been declining in numbers, and those that remain face challenges such as fluctuating enrollments, and reduced budgets. Queen’s University and Northern College have partnered to develop an innovative new program that offers online mining education to engineering technologists seeking to upgrade their skills and obtain a Bachelor’s degree. The high quality, flexible curriculum, offered online, includes a wide range of learning activities that promote interaction (student-to-student, student-to-instructor, and student-to-content), and is enabled by modern learning technologies (an integrated learning platform, as well as a variety of types of purpose-built video, web conferencing, and simulation software). The program issues block transfer credit to college graduates, and consequently reduces the time to completion when compared to other Bachelor’s degrees in Mining. The curriculum has been carefully designed to enhance a balance of technical, managerial, and societal skills for students. The program also includes short summer field school sessions, where students gain practical application skills under the direct supervision of engineering experts. THE NEEDS OF INDUSTRY Canada is the world’s largest exporter of minerals, and the contribution of this sector to Canada’s gross national product is more than three times that of the automotive industry, representing approximately 4% of Canadian GDP (MiHR, 2015)1. According to a recent report by the Canadian Mining Industry Resources Council (MiHR, 2016)2, despite the recent downturn in commodity prices, the industry will continuously need to attract new engineers to replace talent retirements and prepare for the possibility of expansion when the industry recovers. As past experience indicates, the challenges during expansion times are severe and the effects on education counter-productive. For example, during the prolonged expansion cycle of 2006-2012, several new programs were started worldwide, and mining became the profession of choice for many young students. During the subsequent downturn in the industry, many of these programs face dwindling enrollments, placing their sustainability in question. However, there is a continual need by industry to retain employees, as well as attract and train local talent, while providing educational opportunities to its employees. High potential college graduates can find themselves reaching a ceiling in their advancement due to their lack of a University degree. Furthermore, there exists an under representation of women, immigrants, and Aboriginal peoples in the labour force, and engineering fields in general1,2. Traditional mining engineering programs have tried to respond to the needs of industry, as well as meet the needs of students seeking diverse and successful employment careers. These programs tend to cater to the educational needs and aspirations of a general population, and their ability to grow and respond to changing industry needs is constrained by the number of students they can attract, as well as the resources available to them in a steady-state scenario."

Jan 1, 2017

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By D. K. Adjei, G. Ofori-Sarpong, R. K. Amankwah

"Mercury (Hg) is toxic and has long-term effect on the muscle tissues, the brain and the central nervous system functions due to its bioaccumulation and biotransformation effect. Hg pollution around the world is high and this has attracted much global concern such as the Minamata Convention on Mercury, held in 2013. For several years, mercury has been the chemical of choice for Artisanal and Small-Scale Mining (ASM) gold extraction, accounting for about one-third of the global mercury consumption. A greater percentage of this ends up in the environment through open burning of amalgam, spillage and indiscriminate disposal of waste. To break this wall of mercury pollution, it is very important for the mercury used to be recycled through the use of mercury retort units. This brings into the limelight, the Lantern Retort which tries to synergise the high conductivity of steel and the see-through effect of glass, thus, improving the amalgamation process. A research conducted on improving the original Lantern Retort arrived at an appropriate distillation length of 5.08 cm which was used in redesigning a more efficient retort. The improved Lantern Retort recovered about 98% of the mercury used. INTRODUCTION Artisanal and Small-scale mining (ASM) is an informal mining activities which employ quite simple tools such as pickaxes, sluice boxes, shovels, chisels, metal bars, mattocks and water pumps for mining and processing of gold ores. The artisanal and small-scale mining (ASM) sector has served as source of employment for many people in developing countries including Ghana (Aryee, 2001; Hilson and Potter, 2003; Amankwah and Anim-Sackey, 2004; Amankwah et al., 2010) and has provided a substantial amount of foreign exchange through its activities (Hilson, 2001; Styles et al., 2010). Hentschel et al. in 2003 estimated that about thirteen (13) million people are said to be engaged directly in the small-scale mining activities worldwide. However, an estimated 100 million people are said to depend on this sector for their livelihood mainly in developing countries. In China alone, a projected number between 3 and 15 million people are engaged in artisanal and small-scale mining activities (Hentschel et al., 2003), whilst in Ghana, it is estimated that more than 1,000,000 people are employed directly or indirectly in the artisanal and small-scale mining activities, with 10% being women (Amankwah and Anim-Sackey, 2004; Amankwah and Ofori-Sarpong, 2014). In Ghana, ASM gold production has grown from a low of 2.2% in 1989 to a high of 34% in 2014. This figure is estimated to increase with proper documentation. This indicates that the sector has made significant socioeconomic impact on many individuals and communities as a whole. Notwithstanding the above positive contributions, the sector has also contributed to negative impacts on human, aquatic life and the environment in general due to indiscriminate mercury emission. This ‘pollution wall’ needs to be broken, and several interventions have been put in place including the use of retort units like the lantern retort (Adjei et al., 2014; Amankwah and Ofori-Sarpong, 2014)."

Jan 1, 2017

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By Bilgehan Kekec, Sertac Dündar, Niyazi Bilim

"Knowledge of the abrasion resistance of aggregates is important when using them for asphalt and concrete mixes and highway construction materials. In this study, the usability of natural building stone waste as aggregates for different engineering applications was investigated. To this end, test samples were obtained from a number of natural stone quarries and stone cutting factories. The abrasion tests were carried out on the test samples and results were compared between samples. The abrasion strength values were determined with both the Micro-Deval (MDe) and the Los Angeles (LA) abrasion test methods. A correlation coefficient was also determined between the LA and MDe tests results using an appropriate statistical model.Introduction The rapid consumption of natural resources has led researchers to work on the efficient utilization of such resources. To this end one can convert waste into useful raw materials, or determine alternative uses of the industrial waste materials. This has become increasingly important as storing or dumping waste may result in environmental problems. In addition, the use of industrial waste in a different application of the construction industry prevents rapid consumption of limited natural resources and can mitigate environmental problems related to raw material production, Industrial waste such as blast furnace slag, fly ash, building demolition material, marble waste and dismantled asphalt have been used as highway and concrete materials (Ahmed 1993, Ramaswamy and Aziz 1992, Schroeder 1994, Ceylan and Manca 2013, Holtz and Eighmy 2000, Hebhoub et al 2011). It is very important to analyze whether these aggregates are of the required quality in terms of their application and their economic life. This analysis can be carried out using various tests such as the Micro-Deval and the Los Angeles abrasion tests, sieve analysis, durability chemical resistance, peeling and adhesion, and freezing-thawing tests (Erdem et al 1996). Specifications for aggregates also include terms that define the grain shape, cleanliness and surface textures."

Jan 1, 2017

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"INTRODUCTION Drill and blast (DnB) represents the most important, and sometimes the most costly processes in a mine.. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum B. O. and Temeng V. A. 2015). The use of available information to improve the DnB processes can be the difference between a highly expensive process and an optimized one. Mining operations have access to several types of data sets and key information from a wide variety of different systems. This information is normally used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during, and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration, and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety, and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the DnB process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting this data across multiple sites, it becomes valuable to create auditable, automated, and sustainable processes for handling the information. In many cases the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Barbara H. Wixom, Hugh J. Watson, 2007). Our initial implementation plan for the DnB solution included using data stored at the sites; however we learned early on in the process that much of the work for aggregating and supplying the required data was already completed. The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, highlighting the value of using an EDW for managing Drill&Blast information; and to discuss how technical challenges encountered during the implementations were resolved. This paper is targeted at users that want to better manage their DnB data or try to set up standardized workflows for using this information. This case study will discuss the process of implementing a DnB workflow at multiple sites within Freeport McMoRan Inc (FMI) using both data at the sites and information available using the EDW. The paper will begin with an overview of the project. The discussion will then describe how DnB processes were used to set up daily workflows in order to provide information for evaluating process and making decisions. The final section will discuss some of the technical challenges and how they were solved, as well as possible next steps for further improving the workflow."

Jan 1, 2017

By A. Juganda, Jr. Bogin, S. A. Lolon, J. F. Brune, J. W. Grubb

"A longwall gob is mainly filled with broken rocks from the collapsed roof and becomes a porous medium where explosive methane-air mixtures can accumulate. In bleeder ventilation systems, this mixture can migrate out of the gob into the longwall face and other active areas in the mine during barometric or ventilation-induced pressure changes. When external pressures change, the gob does not perceive this disturbance instantly but with a delay due to air flow resistance in the porous gob material. The delay of gob response to outside pressure changes increases the pressure differential across the gob and may cause an outflow of explosive air mixtures from the gob into the adjacent bleeder entries. With computational fluid dynamics (CFD) modeling, researchers at the Colorado School of Mines have evaluated the impact of gob pressure fluctuations on the outgassing of the explosive gas zones (EGZs), the magnitudes and rates of pressure changes, the volumes as well as the potentials location of outgassing if it occurs. INTRODUCTION The air pressure field in underground mines is controlled by many factors such as operating fan settings, ventilation controls, surface atmospheric conditions, and other local events that can intermittently disturb mine pressure, including blasting, roof falls, or inundations. Mine fan settings are rarely changed. Mine atmospheric pressure fluctuations due to adjustments in ventilation controls occur more often during the mining process. Atmospheric conditions and barometric pressures can generate fluctuations in mine pressure on a large scale. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Investigations conducted in coal mines in the United States, Australia, Poland, and South Africa observed higher methane emissions from the gob during periods of falling atmospheric pressures, which led to mine explosions (McIntosh, 1957; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Belle, 2014; Wasilewski, 2014; Lolon et al., 2015). Falling external pressures are understood to cause potential outflow of explosive mixtures from the gob, while rising pressures may push fresh air into the gob. This phenomenon is widely known as gob breathing. The actual processes that trigger gob breathing are not fully understood, nor are the parameters that contribute to the process. Other major events such as roof falls or fan failures can also change the pressure conditions in the mine. In contrast to atmospheric pressure changes, these events can change mine pressures much more rapidly or immediately. TIME LAG AND GOB BREATHING CONCEPT In a bleeder ventilation system, the pressure in the gob is designed to be lower than that of the headgate entries and the longwall face. Air from the gob and gate entries flows towards the tailgate-bleeder returns. When the external pressures are disturbed, this designed pressure arrangement may change, potentially resulting in increased outflow from or inflow into the gob."

Jan 1, 2017