Search Documents

By D. W. Hill

By seeking to define the social and political parameters of both established and potential uses of the underground, this paper will attempt to formulate and state the problem posed in the realms of public choice for obtaining more rapid development and more beneficial use of the underground environments. Essentially, the paper will pursue the following outline: 1. Established policies and established uses of the underground 2. Potential uses of the underground for social benefit 3. Constraints on development and policy a. Psychological constraints b. R & D plus physical constraints c. Economic constraints d. Public choice and policy contraints (both governmental and non-governmental) e. Legal and other structural constraints 4. Defining the problem from the social standpoint 5. Suggestions for surmounting the constraints and meeting the problem: some hypotheses for the future.

Jan 1, 1974

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By Homer S. Anderson

To clarify what r mean about this long title, I would like to define the term technology. A standard definition of the word "technology" is "a technical method of achieving a practical purpose". Incidently, another definition of the term is merely "technical language". The same dictionary defines the word "technology" as "having a special, usually practical, knowledge of mechanical or scientific subject." Naturally, the practical purpose of the subject with which we are concerned is solving of problems we encounter in the mining industry. I might further describe the subject of this discourse by defining the term "manager". An old definition, "one who dispenses the duties of his position with care and economy." In line with the above definition most of the technology with which we in the mining industry are confronted with deals with some form of cost reduction. This may be related to the speed of doing an operation or to saving of labor or supply costs. These can be improvements of an existing method or the result of new processes or inventions, such as new machinery.

Jan 1, 1974

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By James L. Crowe

Electric-power-generating plants fired by fossil fuels are faced with increasingly stringent requirements for control of sulfur emissions. Several approaches for limiting these emissions, or for operating such facilities in an environmentally acceptable manner, are being pursued. Some of the approaches are based on the use of naturally occurring carbonate rocks or of materials derived from them. This paper discusses primarily the carbonate-rock-based processes being developed for control of sulfur dioxide emissions from fossil-fueled electric-power-generating plants. It includes a discussion of the role of carbonate rock materials in removal of sulfur dioxide from stack gases after combustion, capture of gaseous SO2 during the combustion process, and removal of sulfur from fuel prior to complete combustion. Materials derived from carbon- ate rocks are generally used in processes which convert the sulfur to a throwaway product, but there are also proposed processes in which the sulfur is converted to a useful product and the absorbent is regenerated for reuse.

Jan 1, 1974

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By A. D. Rovig

Metallurgical evaluation of autogenous grinding of Anaconda's Berkeley Pit ores indicated that tonnage throughput increases, at a finer flotation feed size, were possible by converting autogenaus mills to steel ball mills. In addition, initial test work showed that the improved grind resulted in slight recovery gains in subsequent flotation processing.

Jan 1, 1974

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974

By Maurice Deul

Limestone can be used effectively in treating acid mine water. Aside from a lower cost than for other treatment agents, limestone has the advantages of easy storage and effectiveness even when impure and in slack sizes. Limestone incorporated into waste piles in layers or as riprap can inhibit acid formation; limestone rubble packed in a mine entry offers promise in formation of a low-cost autogenous resilient seal.

Jan 1, 1974

By Luis de la Pe[n]a Porth

The present process refers to a method for efficiently obtaining high purity metallic copper from copper ammonium sulfite. Essentially, this process consists of submitting the copper ammonium sulfite to the action of heat and pressure with the object of obtaining by the decomposition of it, metallic copper, ammonium sulfate, sulfur dioxide, and sulfuric acid.

Jan 1, 1974

By Alberto Tarsitani

The existing Rome-Florence railroad capacity is inadequate for the traffic volume. To increase this capacity and to reduce the traveling time the Italian National Railroad Administration has decided to provide an additional 400% of rail capacity. This new rail line will be known as the Direttissima Roma-Florence line. It is planned to operate the trains on this connection at speeds of 250 km per hr. Table 1 lists the main design characteristics. [TABLE 1. Design Characteristics Design speed250 km per hr Maximum inclination80 00 (0.8%) Minimum curve radius3000 m Minimum vertical curve radius30,000 m Maximum superelevation in curve 425 mm Type of rail60 kg per m welded] The new rail line will be connected to the existing one by means of high speed switches called "interconnections" so that parts of the new line can be used also by local trains. Construction works for this new line have been divided by the railroad administration into eight sections. Five of these have already been committed to joint ventures. Castiglione Tunnel is a part of the fifth section, 42 km in length, which has been awarded to Consorzio Ferrofir which is a joint venture composed of the construction firms of Astaldi - Di Penta - Lodigiani - Sogene.

Jan 1, 1974

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

By Kenneth L. Schellie

In preplanning the reclamation of a pit or quarry the geology of the site is the name of the game! The planner must know the parameters of the deposit, the quantity and kind of earth materials to be removed, and the amount and nature of the materials to be left behind or wasted as the result of processing the marketable product. With many states and most local jurisdictions requiring reclamation plans prior to the issuance of mining permits, the need for accurate and complete data concerning the geology of the site becomes increasingly important. The producer need only know that marketable materials are available in sufficient quantity to make the mining operation economically feasible-the planner, in order that the land may be reshaped for a useful purpose, must have reasonably precise information as to the dimensions and configurations of the pit or quarry following extraction and the amount and type of materials available on the site (or in some cases offsite as well). Therefore the geology of the site is of major significance in determining the land forms and use capabilities of the property upon completion of the mining process.

Jan 1, 1974

By Thomas G. Langton

The demand for mineral raw materials, especially in the major industrialized nations, has grown rapidly during the past three decades. One consequence of this growth has been an increasing reliance by the large industrialized countries upon nondomestic mineral supplies. These mineral supplies, to a large extent, have been developed by capital from the major industrialized countries. Until recently, most foreign mining ventures were either wholly-owned subsidiaries or joint ventures between two or more mining companies. The recent rise of economic nationalism has substantially changed the business climate and parameters under which foreign investors operate. This paper describes some of the underlying reasons for this change and notes how investors have adapted to the new business conditions.

Jan 1, 1974

By William R. Groseclose, Cecil E. Tackett

Since 1965 when the first mole was used on Bureau work, the Bureau of Reclamation has completed 17 tunnels of over 5,000 feet in length. The longest was 12.8 miles. Total length of the 17 tunnels was 376,207 feet, or over 71 miles. The finished diameter varied from 7 feet 0 inch to 18 feet 0 inch with 82 percent (58 miles) being less than 12 feet 0 inch in diameter when lined. All of these tunnels except one are gravity flow, water conveyance tunnels with relatively flat gradient. One is a low-head pressure tunnel. All were constructed by contracts resulting from fixed-price bids. Starting in 1964 the Bureau of Reclamation initiated the practice of giving several options in the specifications on methods of tunnel excavation. Since that time, construction work has been completed on 17 tunnels. Of this number, 11 were mole excavated and 6 were excavated by conventional drill and blast methods. In general, there has been 2 feet of mole excavation for every 1 foot of drill and blast. Cost comparisons are based on only 13 tunnels because the Bureau has 4 recently completed tunnels that have pending claims; therefore, final cost data are not available. Some definite trends show from the data available; however, the number of completed tunnels in some categories is so small the results cannot really be considered a trend. As more data become available, the indications will become more reliable. The information is presented to indicate general trends and comparisons and cannot be meaningfully used for a one-on-one comparison because of individual tunnel differences not considered.

Jan 1, 1974

By Robin P. Gardner

The mechanistic approach to comminution consisting of incorporating particulate breakage functions into a suitable population balance equation has been developed by a number of researchers over the past decade or so. (1) To date this approach has been developed and demonstrated primarily for batch-operated, laboratory or small-scale ball mills. However, since industrial mills are mostly quite large and operated in the continuous mode; suitable population balance models and methods for obtaining the necessary breakage and other model parameters must be developed. This paper describes and investigates a radioisotope tracer technique for this purpose, Population balance models previously developed(2,3) are adapted for this study.

Jan 1, 1974

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By Richard Newcomb

Since the report of the 1972 Rapid Excavation Conference in the city of Chicago, speculation has continued concerning the estimates of tunneling demand. Little has been published that would persuade me to modify substantially the rather tentative estimates that originated with the National Academy of Sciences-National Academy of Engineering (NAS-NAE) study of 1968 which were recomputed by the United States in the survey of the Organization for Economic Cooperation and Development (OECD) in 1970. The OECD estimates, of course, hedged the really difficult question of forecasting civil construction tunneling demands. In the United States contribution, this was done by predicting both an upper and lower bound for important categories of demand. A discounting procedure was then applied to each of the major sectors of expenditures, permitting a forecast that reflected the current subjective assessment of how extensively and how likely cities were to adopt plans that required tunneling. This was done for water, utilities, transportation and other novel underground facilities. The purpose of this paper is a modest one. In it I wish to describe the efforts made since 1972 to generate more thoughtful and more robust estimates of urban sector demands, and to apply what has been learned to the most difficult category of predictions: those for urban mass transit systems. The estimates of the Underground Construction Research Council funded by the National Science Foundation have been described at an earlier panel of this Conference. The principal effort I am familiar with is that of

Jan 1, 1974

By R. P. Benson, D. H. MacDonald, D. R. McCreath

1 - INTRODUCTION The Canadian Shield is well known as being among the older exposed areas of the earth's surface. Except for local zones, its extent from the Arctic to central North America is characterized by strong and durable crystalline rocks. It is generally regarded as highly competent for tunnelling and underground excavation and, as a result, many openings are excavated in it with minimal temporary support. If hydraulic efficiency is not a factor, tunnels do not usually require continuous concrete linings. A high percentage of the crystalline rocks of the Shield are of metamorphic origin and as such one of the dominant characteristics is their foliation. Zones of sheared or faulted rock are common in the Canadian Shield, particularly in association with foliation. These zones may be created during the late stages of the metamorphic process, leaving shear zones as an integral feature of foliated rock. As foliation is a preferred direction of weakness, deformation and rupture during subsequent tectonism may also create parallel shear zones. These "foliation shear zones", as described by Deere (1973), are an adverse feature of the otherwise durable rocks of the Canadian Shield. The zones may range from faults of major proportions to seams only a fraction of an inch thick. If fault gouge or alteration products exist in the zone the strength of the rock mass may be great1y reduced. As foliation is usually continuous, large unstable wedges of rock may be created if the opening is subparallel to the foliation. The effect on the construction of underground openings in terms of excavations, support and scheduling can be significant.

Jan 1, 1974