Search Documents

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By T. Gupta, T. Ghosh

Rare earth elements (REEs) and their compounds are essential in a multitude of mundane and sophisticated applications such as renewable energy technologies, catalysts, medicine, and defense applications. The global supply deficit could be attributed to the destabilization of REE market that has, as a result, incentivized indigenous production of REEs. Cost-effective and environmentally benign opportunities are being explored for the production of REEs from non-conventional mineral sources including coal and coal by-products to stabilize the supply chain. Coal from Healy coal mine and Wishbone Hill deposits in Alaska have been quantified for REEs and were found to possess elevated total REE concentrations as compared to world average levels (60– 70 ppm). The objective of the study was to concentrate the REEs in the froth phase by froth-flotation of the fine size fraction (< 75 μm). A Box-Behnken design of experiment was employed to ascertain the main and interaction effects of operational parameters on response variable by analyzing 3D response surfaces. Experiments were carried out to maximize REE recovery and concentration by modeling and optimization of three operating variables (frother dosage, pulp density (% solids), and collector dosage). Based on the results, the optimum flotation conditions for maximum recovery at an elevated concentration of REEs in the froth fraction was obtained at 4.2% solids and 32.7 ppm of frother dosage for Healy sample and 10% solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic relationship between the input and response variable was found to be independent of collector dosage suggesting good surface hydrophobicity and floatability of the two coal samples.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By MATT RENAUD, Mustafa Kumral

Mining corporations have spread their operations worldwide in the last few decades. The reason behind widening operations geographically can be seen as it being part of a risk diversification strategy. Given that the technical, financial and social risks are high, favorable deposits, taxation regimes and legislative frameworks create incentives for international mining operations. On the other hand, international mining activities add the risks of permitting, investing, operating and decommissioning to the corporations. These risks could emerge from defaulting, corruption, resource nationalism, social license to operate, and political and legislative uncertainties and instabilities.

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

During dusk, nighttime and dawn operations, effective illumination is a crucial component of safety for getting on/off mobile surface mining equipment and for preshift inspections. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers examined whether illuminance levels could be improved for ingress/egress systems and preshift walkaround inspections of equipment using light-emitting diode (LED) area luminaires. Illumination and glare were key metrics evaluated. Although headlamps provided adequate illumination, LED area luminaires illuminated a much broader area compared to the narrow spot lighting of the headlamp. Hence, the use of additional area luminaires can increase slip-trip-fall (STF) hazard awareness and detection. Furthermore, a commercially available luminaire demonstrated better results than a custom LED luminaire relative to discomfort and disability glare.

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.

By SK SAHOO, UK SINGH, SK SHARMA, GSP SINGH

Surface mining accounts for most coal production in Indian geo-mining conditions compared with underground methods, whose implementations are in deeper coal reserves and for lower stripping ratio in a congested operating space. The bord-and-pillar method is the preferred underground method in India for reasons of flexibility and investment cost. While previous researchers conducted field investigations on intact overburden conditions, this study focuses on the strata control issues in a bord-and-pillar depillaring working under the influence of the dead-load condition of voluminous and fragmented softcover of overburden dump material. The modeling results helped in ascertaining the criticality of strata behavior and rib-pillar stability in actual mining conditions when compared with the conventional intact overburden.

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining the health and safety of miners. This paper evaluates potential real-time monitoring solutions for detecting and reducing diesel particulate matter (DPM), mine fires and dust in situ and examines the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limits. In this study, relevant documents, including research papers, trade publications and manufacturer website information, are reviewed to identify research gaps. This paper also includes evaluations of contemporary sensors (airflow, gas, dust and silica), control system and software technologies, data transport systems, the Industrial Internet of Things (IIoT), ventilation network simulators and control devices to identify potential health and safety research gaps. Examples of some mines in Canada, Australia and the United States that have been using ventilation monitoring and controls are included as well. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

By EREN KOMURLUR, ATILA GURHAN CELIK, IBRAHIM GUNES

In this study, laboratory and site studies were performed to investigate the usability of a new insertion apparatus designed for the split-set type of friction bolts. The new apparatus decreases the friction during the bolt insertion by a temporary diametric compression of the split tubes. According to the results, the new precompression apparatus was found to be advantageous in terms of the insertion practicality and prevention of the buckling problem. By allowing increases in the ratio of bolt diameter to drill-hole diameter, the new apparatus was found to supply relatively high normal stresses and friction capacity in drill holes after opening its clamping mechanism.

By Qingming Feng, Jinhong Zhang

This study investigates the application of fly ash as a high-strength, water-resistant precast construction material through geopolymerization. The experimental results show that working conditions such as water content, sodium hydroxide (NaOH) concentration, curing temperature and curing time significantly affect the mechanical properties of the geopolymer matrix. Through optimization, compressive strength above 100 MPa was achieved, and the optimum working conditions were found to be NaOH concentration of 10 M, water content of approximately 14 to 15 percent, and curing at 90 °C in an oven for one day or at ambient condition for three weeks. Water-soaking tests show that the geopolymerization product has high water resistance without losing noticeable compressive strength even after one month of soaking time. The findings provide a novel method to apply fly ash as a high-strength, water-resistant precast construction material.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By P. Dhar, H. R. Kota, M. Thornhill

A very high-grade calcite deposit located in northern Norway consists of CaCO3 ore with minor silicate and sulphide impurities. Cationic (Tallow-1,3-diaminopropane, Duomeen T) collector has been used in the purification of calcite by flotation with an aim of achieving calcite concentrate for its use in value-added products in a variety of industries. The feasibility of sulphide flotation from calcite by this cationic collector has been initially judged from Hallimond flotation and zeta potential on pure mineral systems and the results illustrate the removal of sulphide from calcite ore at neutral pH region. The adsorption mechanism of diamine on both the sulphide minerals was found to be the same by zeta potential studies. The variations in zeta potential are in good agreement with the adsorption of diamine molecular and ionic species as a function of pH. FTIR studies also showed the adsorption of diamine species in agreement with the zeta potential and Hallimond flotation results. Furthermore, the removal of sulphide impurities with selective flotation by diamine collector was performed in bench-scale flotation with the calcite ore and the results indeed showed that the calcite concentrate could meet the quality requirements for its use in the paper industry for coating and filler purposes.

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

One way to upgrade iron ore is to process it into pellets. The pelletizing process is multifaceted, involving complex fluid dynamics with highly turbulent, high-temperature flow in intricate geometries. This makes it hard to perform measurements during operation, so a useful tool for better process understanding is computational fluid dynamics (CFD), where the challenge is to perform efficient and trustful simulations of complicated problems. A validated simulation model can be valuable for increased process control and development. In this paper, the flow field and coal combustion process in a pilot-scale iron-ore pelletizing kiln is simulated using a CFD model. The objective of this work is to apply a coal combustion model to enable an investigation of thermal effects from the flame on the surrounding flow field.

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By M. Mustafa Kahraman, Sean Dessureault, W. Pratt Rogers

Most contemporary mines have considerable amounts of data. Structured and unstructured large data sets are colloquially named big data. Much of the data in mining operations come from a variety of systems, each with different databases and reporting environments. Standard technology deployments create a Bsilo-ification^ of data leading to poor system benefit. Through modern server monitoring and systematic approach, data utilization and value can quantifiably be measured. The Data Utilization and Value Index (DUVI) can quantify business intelligence best practices and user interaction. This study seeks to provide a data management tool to measure data utilization across the process of converting data into action.

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means of controlling gases and dust. In order to study longwall ventilation in a controlled environment, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers built a unique physical model called the longwall instrumented aerodynamic model (LIAM). The LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel. It has an 8.94 by 4.88 m (29 by 16 ft) footprint with a simulated face length of 220 m (720 ft) in full scale. LIAM is built with critical details of the face, gob and mining machinery, and scaled to preserve the physical and dynamic similitude. This paper discusses the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering and display technologies have generated increased accessibility to virtual reality. Virtual reality allows for the creation of dynamic, high-fidelity environments to simulate dangerous situations and test conditions and to visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers developed a virtual-reality framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization and training. This paper describes the features of VR Mine, including mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.