Search Documents

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

Froth flotation processes are carried out in flotation cells that are grouped into banks, and these banks are interconnected, forming a flotation circuit. A literature review shows the existence of papers related to flotation circuit design based on mathematical programming. However, due to the complexity of solving the mathematical model in most of the work, it is considered that a small number of species is present in the feed to the circuit, which differs from practice. In addition, simple bank models are generally used. This paper presents a methodology for designing mineral concentration circuits that overcomes the problems mentioned. It allows the use of more suitable cell or bank models and the inclusion of several species. The methodology is based on two phases. The first phase identifies the set of optimal structures using discrete values of stage recoveries, solving several mixed integer linear programming (MILP) problems. In the second phase, the optimal design for each of the structures obtained in the previous phase is determined using a suitable model for the recovery at each cell or bank, which results in a mixed integer nonlinear programming (MINLP) model. The design of a copper concentration plant with eight species and the design of a zinc concentration plant with three species and five size fractions by species are used to validate the proposed methodology. The structure of the cells in the rougher and cleaner banks deliver structures that are novel.

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By RICKARD HANSEN

Vehicle fires in underground mines pose a certain risk for which measures to prevent or mitigate the fires are highly important. Fire protection measures can be divided into active and passive measures, where active measures require an external power to work in the event of a fire, and passive measures could include an existing partition preventing fire spread. As passive fire protection does not rely on activation, it is expected to provide high reliability and a robust solution, and should be considered during the design process. This paper investigates passive fire protection measures that could be implemented in the design of mining vehicles. It was found that passive fire protection should include the use of several measures simultaneously to ensure fire protection throughout the different phases of a fire. Threshold distances for fuel components were calculated, and it was found that combining hydraulic hoses and electrical cables resulted in larger threshold distances. A pool fire along the underside of a vehicle will pose a certain risk, and passive measures should be focused on ignition prevention, making high demands on the insulation/shielding along the underside. Any occurring tire fire may pose a challenge, and the priority should be on preventing ignition. Potential measures include shielding the wheelhouse and applying fire-resistant sealings.

By RIINA SALMIMIES, ANTTI HAKKINEN, PAULA VEHMAANPERA

Better understanding of the mechanisms and kinetics of dissolution can benefit several industrial processes. For example, iron can be leached from clays, which can be further used as a raw material in the ceramic industry. Another important application is the regeneration of ceramic filter media, which are used in the dewatering of iron ores. Dissolution of iron oxides in mixtures of acids is fairly uncommon and a less well-understood phenomenon, but it can result in a more efficient process. This work also shows that the determination of dissolution mechanisms and kinetics is not straightforward in different acid systems.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The rare earth element (REE) industry has sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive concentrations. These deposits are extremely uncommon, particularly in the United States. Given the criticality of these materials and the need for a sustainable domestic supply, the current research seeks to leverage the generation and treatment of acid mine drainage (AMD) as an autogenous process that can lead to concentrated REE resources. 

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By D. PATIL, B. K. Parekh

Water is the mainstay for the beneficiation of fine-size coal and minerals, but it is also the least desirable constituent of the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of the individual particles. When a differentially heated solid mixture is placed on a moving belt that has been coated with low-temperature melting resin, the hotter component of the mixture will stick to the belt while the relatively cooler component will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz particles of 6 × 18 mesh size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary test results show that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

By M. Deniz Turan, HASAN NIZAMOGLU, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings, or flotation waste, formed during copper production may be considered in the class of valuable wastes because of the amount of copper they contain. With the decreasing grade values of copper ores, the utilization of wastes like tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental senses. This study was carried out with the aim of using ammonium derivatives for the recovery of copper from tailings waste produced during copper production and utilizing their complex formation characteristics. In the conditions of six hours of leaching at 30 °C in the presence of 22.5 percent ammonium hydroxide and 100 g/L ammonium persulfate, 91.47 percent of the copper was transferred into the solution, while iron was not transferred, indicating that copper can be selectively recovered from tailings.

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), we showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/t of REEs occur in AMD and AMDp, respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. 

By J. D. Miller, C. L. Lin

From mine to mill, the 3D characterization of particles ranging in size from meters to micrometers is now possible. A brief review of X-ray tomography for mineral processing is given with recent advances considered, such as high-speed scanning and image analysis procedures to describe important particle properties, including size, shape and composition. Considering these new 3D characterization tools, applications in mineral processing are discussed for high-resolution X-ray microtomography (HRXMT) laboratory analysis of particles ranging from 20 mm to 5 μm, with a voxel resolution of about 1 μm, including (1) multiphase particle characterization by HRXMT and comparison with scanning electron microscopy (SEM), (2) particle damage state as a result of blasting/comminution, (3) liberation characterization to describe expected separation efficiency, (4) exposed grain surface area analysis to explain the flotation of locked particles, and (5) floc size, shape and water content for polymer-induced flocculation. Finally, applications in mineral processing for plant-site analysis using high-speed X-ray computed tomography (HSXCT) are examined, including, for example, coal washability analysis, the analysis of crusher plant products, and the analysis of pebble phosphate products from central Florida. Scanning rates on the order of 1 kg/min for particle sizes ranging from 150 mm to 1 mm are possible, with a voxel resolution of about 100 μm. For coarse particles smaller than 5 to 10 mm, high scanning rates of more than 300 t/h may be possible at a voxel resolution of about 1 mm.

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

For the first time, surface subsidence prediction theory was used to investigate roof movement around longwall face mining in a steeply dipping coal seam. A physical simulation experiment was conducted to quantitatively study the roof migration patterns, the gob materials, and the characteristics of bed separation and compression caused by mining two adjacent panels to gain a better understanding of ground control issues in multipanel mining in steeply dipping seam. This approach provides an in-depth analysis of the movement of the roof. Compared to movement observation of survey point using total station, the Photogrammetry Analysis for Physical Modeling of Mine Subsidence Program (PAPMMSP) method is easier to perform, faster and yields the much higher accuracy required for scale physical modeling. It is also a more effective observation method for underground-mining physical simulation experiments.

By Turan Uysal, Thierno Saidou Barry, MURAT ERDEMOGLU, Mustafa Birinci

Nonbauxite ores such as aluminum silicate clays and coal fly ashes have been widely considered as potential resources of alumina (Al2O3). The interest focused on these ores is due to their high alumina content. Over the years, in countries where there are little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process is not economical, alternative processes have been explored. Among these processes, acid leaching is seen as the most attractive process. In the acid leaching process, heat treatment for thermal activation to destruct the refractory structure of the minerals in the ores is generally recommended as a pretreatment method. Recently, the applicability of high energy ball mills, which are useful for mechanical activation as a pretreatment method before leaching, has attracted much attention. This is a short summary of our previous review [1], giving the details of alumina manufacturing from thermally and mechanically activated clays and coal fly ashes by acid leaching.

By Sean Dessureault

The mining industry has used fleet management systems (FMSs) for decades. These systems were developed long ago in large truck-and-shovel mines, where hardware sales were the core business driver for vendors. These traditional models can be overhauled in the era of the Internet of Things (IoT), Big Data, gamification and low-cost tablet technology. Relatively low-cost tablets are ubiquitous in modern life, and they are packed with communication radios and sensors like Global Positioning System (GPS) and inertial measurement units used widely for games, fitness measures and navigation. These powerful computer devices provide the same, if not more, sensing capability than traditional fleet management hardware, all at a fraction of the cost and without complicated cables or challenging supply lines. 

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Chen-Luh Lin, Jan D. Miller

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of centimeter size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of millimeter size. Based on Micro-XCT, it was expected that 85 percent of copper for sample A could be recovered at 65 percent of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual-energy X-ray radiography was used as a basis for sorting. Pilot-scale X-ray sorting of sample A (10 × 1 cm) showed 31 percent rejection of a 0.08 percent Cu gangue product with a corresponding recovery of 90 percent copper.