Search Documents

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão Mine in Brazil. They are predominantly blue apatite, followed by green apatite and, less frequently, yellow apatite. The chemical compositions of these types of apatite were determined by electron microprobe analysis and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). Blue and green apatite responded well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite has the lowest phosphorus pentoxide (P2O5 ) content and largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest phosphorus (P) and calcium (Ca) grades and lowest substitution level.

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

By Isabel F. Barton, Christian A. Rathkopf, Mark D. Barton

Rhenium (Re) is one of the rarest elements on earth and is a designated critical element in the United States and European Union for its uses in superalloys. Unusually among critical elements, Re is produced entirely as a byproduct of molybdenite (MoS2) mining, as pure Re minerals are extremely rare. However, Re concentration in natural molybdenites varies from a few parts per trillion to tens of percent. There are few known consistent patterns and no firmly established reason for this variation, making it difficult to use molybdenite Re content as a proxy for metal grades, a vector to high grades, a clue to the geological and geochemical nature of the ore deposit, a guide to overall Re resources or for any other of the applications that have been suggested for it over time. 

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By KALLAM VK REDDY, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

Mining activity around the world has increased significantly to meet stepped-up demand for various metals [1]. Apart from the target minerals, mining also generates huge amounts of unwanted minerals that exit the mines as overburden. Due to the active mining activity, high-grade mineral resources are being depleted, leaving inferior-quality ores [2]. The mining of low-grade ores further increases the amount of overburden/waste per ton of metal equivalent of ore mined. Currently, overburden and other mine waste is most commonly used in the construction industry and as feedstock for making cement and concrete, but the overburden can also be used as a source of valuable minerals and metals [3]. 

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Increasing demand for high-grade manganese (Mn) ore has led to the practice of selective mining, which produced low-grade Mn ore as waste and in the long term could lead to environmental pollution. Research had been carried out to extract Mn from low-grade ore, which mostly exists as black Mn(IV) oxide (MnO2). Most extraction methods involved the reduction of insoluble MnO2 to soluble Mn2+ in acidic media. Metals other than Mn are also transferred to the pregnant leach solution (PLS) during the leaching process, especially iron (Fe). Due to high Mn concentration in PLS, precipitation is considered the best method to isolate Mn from PLS compared with solvent extraction and ion exchange/absorption. However, due to unselective leaching, the presence of Fe in the PLS makes the Mn separation and purification difficult. Therefore, in this research, the parameters affecting the selectivity of Mn over Fe in leaching process were investigated.

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

Increasing attention is being paid to laterite nickel ore as an alternative to nickel sulfide ore to act as a feedstock for nickel metal production. While laterite nickel ore accounts for a lion’s share of global nickel resources at approximately 72 percent, it accounts for only 42 percent of the world’s nickel production. In addition, the processing of nickel sulfide ore is confronted with enormous challenges due to deeper drilling requirements, higher production costs and depleting reserves. The nickel content in the nickel laterite ore associated with hydrated iron oxides and silicate minerals limits the application of physical beneficiation methods for the removal of iron. Thus, magnetic reduction roasting followed by magnetic separation has been regarded as one of the attractive routes to concentrate and separate the valuable metals from the impurities. 

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll on the U.S. coal mining industry. Recent health surveillance data indicate that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied to reduce dust levels. An overview of CWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

By H. Y. Yang, L. L. Tong

Semicontinuous-flow, multistage biooxidation experiments of a Chinese refractory, high-sulfur gold concentrate were conducted with different pulp densities for gold recovery. The maximum iron, sulfur and arsenic oxidation rates of 90.0, 88.8 and 96.4 percent, respectively, were obtained in the experiments with 5 percent pulp density. The highest gold and silver recoveries of 96.1 and 68.9 percent, respectively, were achieved by cyanidation. The negative effect of high pulp density on biooxidation was related to the decrease of free and adsorbed cell concentrations with increasing pulp density. The data of iron oxidation from the semicontinuous biooxidation experiments were best fitted by a shrinking core model in which the chemical reaction controlled the rate. The dissolution kinetics of sulfur and arsenic were therefore analyzed by a shrinking core model in which the internal diffusion controlled the bioleaching rates. For the quantitative description of biooxidation efficiency, two parameters — mass dissolution rate and volume dissolution rate — were proposed. In the first stage, the mass dissolution rates of minerals were negatively correlated while the volume dissolution rates were positively correlated with the actual pulp density. The iron and sulfur mass dissolution rates decreased with increasing actual pulp densities in the third and fourth stage, while linear increasing relationships between the volume dissolution rates of minerals and the actual pulp density were observed from the second to fourth stage. The highest mass dissolution rates of minerals were obtained in the first stage with 5 percent pulp density. The highest volume dissolution rates of minerals were obtained in the first stage with 15 percent pulp density. Compared to the volume dissolution rate, the mass dissolution rate was more intuitive to reflect the negative effect of high pulp density on biooxidation efficiency.

By Nicolin Govender, Pramod Kumar, Raj Rajamani

Mill power models have been used in a variety of ways in industrial practice since power directly equates to throughput and fineness of ground product. We first start with Hogg-Fuerstenau Power Model and show how this model successfully predicted the power draw of many grinding mills in several mining operations. Then, we show how this model was on the verge of being able to predict the influence of lifter design on power draw. Next, we describe the discrete element model and how it overcame the issues faced by the previous power model. Using a DEM software known as Millsoft, we show the influence of lifter design geometry on power draw and analyze the power draw of rubber lifters versus the steel lifters via several case studies. As years passed, the two-dimensional discrete element model imbedded in Millsoft is superseded by three-dimensional discrete element method. Due to the gigantic computational power of graphic processing units, new computational codes that can do the tumbling motion along the entire length of the mill has come about. Here, we show the predictive capability of Blaze-DEM for ball and SAG mills.

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

 This research project explored the viability of a new mining technology — thermal fragmentation — in narrow-vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation as well as one of an existing method used for narrow-vein mining. Comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs as well as increased productivity and ore recovery meant that the new method would improve the financial performance of any operation.

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

Reducing the contribution of heavy- and light-duty diesel-powered equipment to concentrations of aerosols and gases is essential to industry’s efforts to improve air quality in underground mining operations. The results of this study demonstrated a potential of control strategies based on retrofitting existing power packages with diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) systems and repowering existing systems with advanced power packages to reduce contributions of diesel-powered vehicles to concentrations of diesel aerosols and criteria gases in underground mines. The implementation of viable exhaust aftertreatment systems and advanced diesel power packages could be instrumental in the underground mining industry securing a clean, economical and dependable source of power for mobile equipment.

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in byproduct molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have immensely reduced the possibility of hydrogen sulfide (H2S) gas evolution. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Bench-scale rougher flotation results for samples from the Sierrita copper–molybdenum (Cu–Mo) plant showed the best DCMT performance at 8 kg/t of DCMT, pH 10.5, 30 min of shear conditioning and 10 min of flotation conditioning. The Aminpro plant model simulation confirmed that 4 to 8 kg/t DCMT under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared\ to NaHS.

By LUIS ALBERTO TORRES-CRUZ

The Plewes method is relatively well known among geotechnical engineers interested in assessing the liquefaction potential of soil deposits. Furthermore, it was one of the four methods considered in the post-failure investigation report of the Feijao Dam I, also known as the Brumadinho Dam, in Brazil. The inclusion of the method in that report is likely to increase its visibility among geotechnical practitioners tasked with assessing the liquefaction potential of tailings. While the authors of the method duly presented it as a screening method, more recent technical literature contains conflicting views on its reliability. Considering the popularity of the method and that the safety record of tailings dams is a cause of great concern, this study assessed the uncertainty of results from the Plewes method. The study concludes that, even under optimistic assumptions, the results of the method are too uncertain for detailed characterization of tailings deposits.