Search Documents

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

By Frank McKinley

This paper discusses the basic requirements covering the area between the initial discovery of a deposit and a decision as to whether or not the deposit will support an economically sound mining venture. The procedure for gaining the necessary information and the sequence of steps is in .some respects parallel to gaining like information on deposits other than the sand type. For the sake of simplicity the stages and sequence are presented as follow: first, the initial reconnaissance drilling; second, the exploration drilling to permit initial ore body estimates; third, metallurgical testing; fourth, the estimate of plant and operating costs; and last, the economic balance. The objective of the reconnaissance drilling is to collect sufficient information to reach a decision as to the advisability of further exploration or the abandonment of the area. This initial phase will comprise, in addition to some drilling, a thorough reconnaissance of the area, a study of the best geological and topographic maps of the region, and a study of any literature available, all under the guidance of a geologist.

Jan 1, 1958

By R. B. Taylor

The Esmeralda mine is located about three miles west of the town of Parral, in the State of Chihuahua, Northern Mexico, and about 400 miles south of El Paso, Texas. The area is serviced by the Interamerican Highway and a branch line of the National Railways of Mexico. The Parral district is quite typical of the semidesert of Northern Mexico, lying near the western margin of the Chihuahua basin and range province known in Mexico as the ?Mesa Central? In the immediate mine area, low rounded hills and rolling plans slope toward the Parral River. Surface elevation at the mine is 5,800 feet. The Esmeralda vein outcrops strongly, but was too low grade to be of interest to the Spaniards, The first claims were staked in 1897 and limited exploration work to a depth of 550 feet was carried out prior to 1912, at which time work was suspended. The Eagle-Picher Company acquired the property in 1944 and by surface diamond drilling outlined an orebody to a depth of 800 feet, Minas de Iguala, S. A, de C.V., one of Eagle-Picher?s totally owned subsidiary companies in Mexico, then unwatered the old workings, developed the mine, installed a modern differential flotation plant and started production lage in 1948. To the present, more than two and ahalf million tons of ore have been mined and milled producing lead and zinc concentrates.

Jan 1, 1958

By Charles Banks Belt

In 1925, Niggli (1925, pp, 1-69), formulated a physico-chemical, explanation for the origin of hydrothermal ore deposits, from a concept that had appeared earlier in the literature in the writings of Von Groddeck, Stelzner, Beck, de Launay, Kemp, and Lindgren. Niggli proposed that pressure at depth could force volatiles from deep-seated magmas. The volatiles would In turn form pegmatites and then ore deposits as the fluids cooled. This is one view of a general theory of ore genesis that gained secondancy for years among such prominent geologists as Fenner (1926, p, 697) and Emmons (1936, pp. 29-70). It was, proposed that ore deposits were precipitated from solutions or fluids that had escaped or been separated from a deep-seated magma by means of liquid immiscibility or crystallization or gas transfer. This theory is based on the presence of igneous rocks close in space and age to hydrothermal ore deposits in many mining districts of the world. As is well known, there are many ore deposits apparently of hydrothermal origin that are neither spatially nor chronologically related to igneous rocks, In still other localities where there are no hydrothermal ore deposits, igneous rocks occur that are similar in composition to those in mining districts. In view of such facts, the applicability of the Niggli theory to all hydrothermal ore deposits may well be questioned. The chief purpose of this paper is to test the Niggli theory by studying the primary petrology, hydrothermal alteration, and distribution of copper and zinc in silicic igneous plutons supposedly genetically related (in the Niggli sense) to nearby hydrothermal ore deposits, Silicic Tertiary plutons in three New Mexico mining districts were chosen, the Hanover-Fierro intrusive at Hanover and Fierro, the Granite Mountain pluton at Magdalena, and the four outliers of the Lordsburg stock at Lordsburg. First, it had to be established whether the observed plutons were or were not the source of the adjacent ore deposits. This was done by studying the relation between the copper or zinc distribution-and the primary or secondary features in the plutons studied, and the time relations between instrusion and ore deposition. Primary igneous features of a pluton are defined as the minerals, texture, shape, and character of the pluton which were formed prior to the complete solidification of the rock, secondary features include all changes that took place in a pluton after solidification. They are identified by their cross cutting nature or as replacing primary minerals, Under the Niggli concept, it is proved that the ore ions did not originate from the parts of the pluton now visible as immediately adjacent to the ore deposits; it must then be established, if possible', that the ore ions were separated from deeper parts of the intrusive, Some idea as to whether the copper or zinc ions originated from a related magma at depth may be gained by a comparison between the primary (that is, pre-alteration) zinc and copper abundances found in ore localizing intrusive studied and the average abundances for copper and zinc in silicic igneous rocks most recently given in the literature. Finally, the relation between ore deposition and hydrothermal alteration was studied on a regional as well as on a local scale.

Jan 1, 1958

By Frank J. Markewicz

The expanding: demand for ilmenite for use in the manufacture of titanium pigments, the knowledge that much of this raw material comes from distant points and therefore has to include a heavy freight charge in the price of the delivered product, and the further knowledge that ilmenite occurs both in the crystalline rocks of northern New Jersey and also in some of the Triassic igneous rocks, were considerations which led to a search for ilmenite-bearing sands in southern New Jersey. That this search was successful is now history, and it is the senior author's privilege to state here that most of the credit belongs to his associates who did all of the heavy work of hand-augering for samples, and who made all of the heavy-mineral separations. We all are grateful to members of the Department of Geology at Rutgers and Princeton Universities for the use of equipment which enabled us to evaluate certain samples from our ilmenite exploration program. In addition, we wish to express our appreciation to many companies for their cooperation and for their permission to publish mineral and chemical analyses. We also acknowledge with much appreciation our debt to the geologists and engineers with whom we have had many lively and rewarding discussions relative to the ilmenite deposits.

Jan 1, 1958

By Harold Bloom

Dimethylglyoxime reacts with nickel in a buffered ammonical-citrate solution containing the detergent ?Aquet? and hyroxylamine-hydrochloride. The resulting nickelous dimethylglyoxime is extracted with xylene. Visual comparison with standards permits the estimation of from 50 to 10,000 ppm of nickel. Soil, rock, or sediment may be decomposed by digestion with (1-3) nitric acid, allowing about 70 determinations per man-day to be carried out. With minor modifications to the above procedure, sediment and soil may be semi-quantitatively analyzed for nickel at the sample site. The chemical equipment is easily portable and the analysis extremely rapid because the buffer, dime thylglyoxime and xylene are added simultaneously to the sample and no heating is required. The sensitivity varies with the "availability" of the nickel ions; under favorable conditions, one may obtain a positive test for as little as 10 micrograms in soils and sediments. This procedure is similar to one, for the field determination of heavy metals described elsewhere by the author.

Jan 1, 1958

By C. R. Nailler

Two recently published papers describing the use of psychological tests for selection and placement of coal mine personnel have created considerable interest within the Coal Industry, one paper, published in the April 1957 "Mining Congress Journal," entitled "Personnel Evaluation and Training," discusses the use of tests by the Christopher Coal Company, The second paper, published in the "West -Virginia Coal Mining Institute's 1957 Report" and in the September 1957 "Coal Age," entitled "Testing to Select Better Personnel for Coal Mining Today," outlines Hanna Coal Company's test and selection procedures. Since these rather detailed sources are readily available, and to avoid repetition of the material in them, we will confine this paper to a very brief review of the essential steps already taken by these companies and a more extensive look at newer material. Briefly, the Personnel Managers, Mr. Harold L, Durrett and Mr. Albert M,. Rowe, of the Hanna Coal Company and Christopher Coal Company, in conjunction with Dr. Quin F, Curtis, Head of the Psychology Department of West Virginia University, developed two different groups oftests for coal mine personnel, The first group oftests was designed to assist in the selection of supervisors. These tests of the supervisory group were "The California Short Form Test of Mental Maturity - Advanced Series," which gave an I.Q. rating, and the second test is known as "The Minnesota Multiphasic Personality Inventory," which measures several personality characteristics, These tests must be given, grade, and interpreted by a person trained in psychological testing. As a result of testing all of Christopher's supervisory employees (seventy in number) by this method, and then comparing the individual results with the individual ratings of the foremen on the job, a so-called foremen's scale was developed. If this resulting foremen's scale had been used to select the foremen who were rated as, the best men in on-the-job performance, it would have correctly identified seventy-four percent of that group.

Jan 1, 1958

By D. S. Dinsmoor

Boron, estimated to comprise about 0.001 percent of the earth's crust (Fleischer 10), as an element is never found free in nature, although its compounds are found in many localities. the borates are the most important. Sassolite (B(OH)3) and boracite (Mg6C12B1406), non-borates, are-of-minor importance. The crystal structures of most natural borates are still unknown. A classification based solely on the ratio of boron to the total number of cations has been devised (Palache 28). This classification divides the borates into four, sub-groups; anhydrous borates, hydrated borates, borates containing hydroxyl or halogen and compound borates. Only four or five minerals of the hydrated borates group have ever been used commercially. In more recent years, the sodium borates have comprised all but a 'small fraction of all borates used. Borax, the hydrated borate compound, is the most important of all boron compounds. It has been used so long and so often that the layman often confuses borax and boron and, applies the terms synonymously.

Jan 1, 1958

By John E. Bailey

The advent of Nuclear Energy has caused a phenomenal growth in the uranium mining industry. To keep abreast of this surge the mining industry has located many ore bodies, determined the best types of mining adaptable to this particular type of ore and developed a highly specialized type of operation. But, has the mining industry gone far enough in the planning? Has ?built-in? safety been included in the efficient methods of operation? Preplanning safety in the mining industry, as in all industries, takes engineering and ingenuity combined with the experience and cooperation of all concerned. A system of mining can be planned on a map and it will look good. However, when the actual mining takes place, conditions may be such that deviations from the original plans may be required because of excessive water faults or other conditions encountered. With safety we may also be required to change, to conform to the characteristics of a particular operation. People in the mining industry are well aware that loose back has killed miners each year. This condition occurred in practically all types of mines. The condition is not new to us. It is also known that explosives, haulage, machinery and conditions common to all types of mining have taken a heavy toll of human life in mining. In addition to these hazards in the uranium mines, the hazard of radon is also present, Radon is a radioactive gas liberated from ores containing radium. This gas is released into the active workings by the blasting or breaking up of the ore. Sometimes it is caused by radium contaminated water seepage from abandoned workings or from the ore body itself. Until the action of this gas on the human was known, many miners were affected. Un- less adequate precuations are taken to protect the people in these mines,, they may be exposed to this hazard, Health researchers made a study of this substance to determine how it would affect the health of the men, They also studied men who had worked in previous years, in mines known to have contained radioactive materials. All of this research contributed to the present knowledge of radon and its daughter products. It is not flammable nor explosive, but, if allowed to enter the body through the respiratory organs it can cause serious damage. Mines have been operated in the past and are still being operated, which were known to contain explosive and noxious gases, indicating that this problem can be controlled. Several states have instituted laws that make it mandatory to provide adequate ventilation and use of monitoring devices to limit radon and its daughter products to a maximum of 300 micro-microcuries per liter of air. This is considered a safe limit for sustained periods of human exposure. While the findings of research do not prove conclusively that the inhalation of excessive radon or its daugher products cause lung cancer, indications point to this as a possibility, particularly radium A and radium C1 of the daughter products. The threshold limits set by law in most uranium producing states are believed to be safe. In a few years, when tests and data now in the process of collection by interested state officials and laboratories is complete, these limits may be found to be ready for revision. Studies such as these take time. At present, the limits that are used are based upon estimates. The permissible limits of exposure to radon and daughter products include a large safety factor. It is considered that a good supply of fresh air delivered to the working places, adequate dust control, the sealing of unused or abandoned workings, the removal of mine water which is generally contaminated and a safe waiting period after blasting, will hold to a minimum the dangers from this source. There are, of course, problems accompanying each of these procedures. For example, the ventilating of untimbered raises and bringing fresh, uncontaminated air to the working places may be a problem. However, a good mining man can solve these problems as they apply in each particular operation. From the information available at the present time, the daughter products containing polonium and emitting alpha radiation, may be a health hazard. Fortunately, the half life of most of the daughter products is short, however, radium D has a half life of 22 years and presents a problem of contamination in the storage of old tailings. So we can see that failure to comply with the accepted good mining practices may have harmful effects on the health of miners. It is gratifying to note the interest in this potential hazard by the officials in the uranium ore producing states, who are making extensive studies and keeping records of the men who work in this type of mining. This all provide information necessary for preplanning safety. By contrast, little has been accomplished to control the injuries and deaths from some other factors connected with most underground mining operations. I would like to discuss briefly one of the hazards which take an annual toll in our underground mines, this is falls of back and walls. This problem or hazard is present, and will be

Jan 1, 1958

By Walter B. Hester

All persons and communities that have experienced strong-motion earthquakes are convinced of the importance and complexity of earthquake problems thatmust be solved in order to reduce the personal hazards and property losses to a reasonable minimum. It is also clear that absolute elimination of all risks is impossible. Reduction of existing hazards and precautionary measures which will minimize chances for disaster can be accomplished by realistic appraisal of the effects of recent earth- quakes on modern structures and installations. Localities that have reason to expect so-called strong- motion earthquakes can anticipate these effects by taking appropriate steps. Valid earthquake information can only be obtained from earthquakes. Each earthquake contributes to the body of knowledge by additional facts and by clarification of previous observations. Rational interpretation of the data followed by practical application of the conclusions can contribute greatly to the safety of persons and property. The general public expects the architectural and engineering profession to accept this obligation and render this service. Most earthquake hazards are man-made and arise from the imperfections of the works of man and his failure to anticipate the consequences when the natural characteristics of his environment are ignored. If it is not given to man to prevent such natural phenomena as earthquakes, it is sometimes within his power to control their destructive effects and to reduce to a minimum the toll of life and human suffering.

Jan 1, 1958

By R. M. Wilson

Concentrating plants, in common with other types of industrial plants, cannot operate without lectric power. The elctric distribution system and utilization equipment; therefore, must be carefully considered in all phases of plant design. Two important aspects of proper distribution and usage of electric power are the selection of voltage levels and the methods of system grounding. These are not necessarily the most important design considerations, but are perhaps more controversial than other major points, Modern plants demand increasing amounts of power which, since electric power is the product of voltage and current means higher voltages or currents. Higher voltages require more insulation, higher currents more conductor. The equipment designer?s problem is to obtain in his transformer, cable, switchgear, controller, motor, etc a balance of insulation and conductor to obtain a satisfactory design at lowest cost. To provide the most economical system, both in initial and operating costs requires the system designer to select the proper voltage level. Adequate voltage also permits expansion to meet future requirements, and results in better operation of utilization equipment, Relatively little advancement has been made in recent years in improving conductors; however, great progress has been made in improving insulation. Thus modern plants, in general, now find it more economical to use higher voltages than they did previously. For example plants which only a few years ago would have used 2400 volts as a system voltage often find nowdays that 4160 volts is their proper choice. If the plant requires 10,000 kva br more, then an even higher voltage, such as 13,800 volts, will prove economical. However, for the average concentration plant, with less than 10,000 kva demand, the choice of distribution voltages is between 2400 and 4160 volts, and 480 volts will be used for the low voltage utilization system.

Jan 1, 1958

By R. L. Ziegfeld

It has often seemed to me that people are too prone to turn to new and untried materials in an effort to solve their problems, without giving sufficient consideration to the old stand-bys, except as a last resort, It?s a little like middle-aged men who are swept off their feet by the fresh beauty of a young girl without first considering the many advantages that a more mature woman has to offer. Maybe it?s because, like the older woman, the older materials have to make a determined effort to keep themselves looking young and attractive. T at?s just about the situation with which the lead industry is laced. We have to make a determined effort to keep lead looking young and attractive to industry. However, there is one difference and it is important, Lead can not only be kept looking young, but it can, in fact, actually be kept young, This results from two things. First, industry and technology are constantly changing. For example, we have known for years that the density of lead makes it ideal to stop gamma rays, but it is only recently that atomic fission as a source of gamma radiation has become an important tool of industry, That makes old knowledge about lead useful in developing a new market for it.

Jan 1, 1958

By Edward F. Nagle

Instrumentation engineers have recently devised practical methods of metering the net solids flowing in a hydraulic mixture. The solids flow rate is determined by measuring the specific gravity and the flow rate of the mixture. T e specific gravity is measured by a variation of the bubbler system. The flow measurement is made by a somewhat unorthodox orifice requiring field calibrations. The linear mixture flow signal is then multiplied by the specific gravity signal, which is directly proportional to the percentage of solids in the mixture, to produce a linear solids Slow rate signal. The computations in this system are performed by Sorteberg pneumatic relays. Having obtained this measurement, integration and automatic control of hydraulic solids flow are available. This system is useful in mining, drilling and dredging industries. It provides maintenance of the net solids flow rate and reduces power consumption. Automatic control will provide rapid stabilization of net solids flow rate and release operators from making menual adjustments. The advantages of this application are economy of operation and increased pump efficiency, This paper describes a hydraulic solids flowmeter system installed aboard a dredge. Its purpose is twofolds:- 1. 20 provide a summation of the net solids flowing 2. To make available a practical guide for the drag tender operator. (Dwg. GSD-2219)

Jan 1, 1958

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Duluth & Iron Range Railroad. The Duluth & Iron Range Railroad was built from Two Harbors to the Vermilion range at Tower, a distance of 67.6 miles, in 1884, and extended to Ely, twenty-one miles east of Tower, in 1888. It was built into Duluth in 1886, and branches were extended from its main line to the Mesabi mines in 1892 and 1893. The original grades on this road are very steep, going north, and in the thirteen miles from Two Harbors to Highland there is a rise of 1,150 feet. A new line between these points has been built with an increase of three miles in distance and with maximum grades of 1 per cent. Duluth, Missabe & Northern Railway. The Duluth, Mis¬sabe & Northern Railway was constructed from Stony Brook to Mountain Iron, a distance of 48.62 miles, in 1892. The Biwabik branch from Iron Junction to Biwabik, a distance of 15.54 miles, was constructed in 1892. The Superior branch from Wolf to Hibbing, a distance of 16.06 miles, was co11structed in 1893. The Alborn branch from Coleraine Junction to Coleraine, a distance of 53 miles, was constructed in 1906. The total main line mileage is 242 miles, of which 82 miles from Duluth to Hibbing is double tracked"

Jan 1, 1920

By Alexander N. Winchell

"The waters of Lake Superior flow into those of Lake Huron through the St. Mary's river. The rapids in this river are about half a mile wide and three-quarters of a mile long, in which distance the fall amounts to about twenty feet. Since this was the only obstacle to navigation between the west end of Lake Superior and ports on any of the other Great Lakes except Ontario, attempts were made many years ago to permit the passage of small boats from Lake Huron to Lake Superior by means of canals and locks. The first canal was built on the Canadian side of the river by the Northwest Fur Company in 1797-98. The lock was 38 feet long, 8 feet 9 inches wide and had a lift of 9 feet. A tow path was made along the shores for oxen to track the bateaux and canoes through the upper part of the rapids., The lock was destroyed during the war of 1812 by United States troops from Mackinac Island.The first ship canal, known as the State Canal, was built on the American side of the river in 1853-55, about 750,000 acres of land in Michigan having been granted by congress to a private company as a 'concession for its construction. This canal was more than a mile long, 65 feet wide at the bottom and 100 feet wide at the water's surface. It had two locks, each 350 feet long by 70 feet wide, with a lift of about 9 feet. The depth of water in the canal was about 13 feet and in the locks about 11 1/2 feet."

Jan 1, 1920

By Alexander N. Winchell

"Location. The iron formation of the Gogebic district (including the Penokee) comprises a narrow belt south of the western part of Lake Superior extending from Michigan for a considerable distance into Wisconsin. From the mouth of the Montreal River (about twenty-five miles west of Ashland) the iron formation is only about twelve miles distant, but it is about twenty miles south of Ashland. Beginning on the east at a point about eight miles east of Wakefield, Mich., it extends through Sunday Lake, Bessemer and Ironwood in Michigan, and thence south of west through Hurley, Wis., and only a short distance south of Mellen, Wis. About eight miles westward from Mellen, the formation disappears, but six miles further west it is known to reappear and continue thence for about eight miles. The total length of the range is about sixty miles, two-thirds of this distance being in the State of Wisconsin; but nearly all of the ore has been obtained from the eastern third of the district, which is in the State of Michigan.History. This iron range was first noted in 1848 by Dr. Randall, assistant geologist to Dr. David Dale Owen, while following the fourth principal meridian northward. It was also reported by Charles Whittlesey in an account of a survey made in 1849, and published by Owen in 1852. Analyses of the iron ore are given with the following account. ""The bed of magnetic iron ore south of Lac des Anglais is of extraordinary thickness,25 to 60 feet. * * In the wild and deep ravines where the Bad River breaks through the range, there is a cliff of slaty ore * * * probably three hundred feet thick. * * * I estimate more than one-half of this face to be ore, and in places the beds are from ten to twelve feet in thickness, with very little inter-mixture of quartz * * * . The position of the best exposures of ore which I saw is such as to require from eighteen to twenty eight miles of transportation to reach the lake."""

Jan 1, 1920

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The Vermilion range extends from the vicinity of Tower to and beyond the ""international boundary, crossing into Canada at the eastern end of Hunter's Island. Merchantable bodies of ore have been discovered at but two localities along this extent, at Tower and at Ely, twenty-one miles east.The iron bearing formation of this range occupies the lowest position geologically of any of the Lake Superior iron formations, being placed by Van Rise and Clements in the Archean, as shown from the following succession:Lower Huronian Intrusive granites, granite porphyries, dolerites, and lamprophyresKnife Lake slatesAgawa formation (iron-bearing) Ogishke conglomerate(Unconformity.)ArcheanIntrusive granites, granite porphyries, and some greenstonesSoudan formation (the iron-bearing formation). (Minor unconformity.)Ely greenstone, an ellipsoidally parted basic igneous and largely volcanic rock The ores of the Vermilion series occur in the Soudan formation (the Agawa iron bearing rocks are not of commercial importance).At the Minnesota mine at Soudan the ore is a dense, hard hematite, occurring in irregular connected and disconnected lense shaped bodies in the jasper, which is intricately infolded in the ellipsoidal greenstone or green schists, so called on account of a characteristic ellipsoidal parting. The strike is about east and west and the dip approximately vertical, with a westerly pitch. The underground workings at this mine are some 4,500 feet in extent east and west, and over 1,500 feet in depth. The structure here is probably the most complex in the Lake Superior iron districts. Above the iron bearing formation, geologically, comes the basal conglomerate of the Lower Huronian, carrying large boulders and Masses of the iron bearing rocks."

Jan 1, 1920

By Alexander N. Winchell

The construction and erection of the Coleraine concentrating plant was commenced in April, 1909, and was completed (with the machinery installed) ready for use in 1910. Attached to the main building is 'a table house large enough to accommodate con¬centrating tables for five units and space for a small machine shop and supply store. For the handling of the' railroad cars in the upper portion of the mill there is provided on the north side of the main structure a trestle approach 650 feet long, and on the south or opposite side a tail track 300 feet long. The latter is so constructed as to permit its being incorporated directly in a possible future extension of the plant. The building, viaduct approach and tail, trestle, as well as the table house, are con¬structed of steel, the total amount used being 6,100 tons. The building is covered by corrugated' steel sheeting over 2 x 6-inch wood sheathing fastened directly to the structural steel. The north end of the trestle approach is connected with the main road-beds forming the track system for delivery of the crude ore to the plant over an embankment of a maximum height of 110 feet containing over 2,000,000 cubic yards of dirt.

Jan 1, 1920

By Alexander N. Winchell

The cities of St. Paul and Minneapolis are located side by side on a double loop in the Mississippi River near the eastern boundary of Minnesota. Both cities lie on both sides 'of the Mississippi River, which in this region describes an S-shaped curve. The two cities together have a population of over 600,000 people, gathered in an area which has grown to be a single urban district inasmuch as the two cities have expanded until they occupy all the territory formerly between them, though the business centers are ten miles apart. St. Paul is located at the head of navigation on the Mississippi River and Minneapolis, farther upstream, at the Falls of St. Anthony. A recent water¬power development below the Falls of St. Anthony, constructed by the Federal Government, has at the same time made possible navigation to the foot of St. Anthony Falls through a lock around the dam which replaces the former rapids. Minneapolis, in 1920, had a population of 380,000 people, and St. Paul, 235,000. The two cities occupy land at an elevation of 700 to 900 feet above sea level. The average elevation is slightly less at St. Paul. Minneapolis has nearly 4,000 acres of parks and park¬ways, while St. Paul has nearly 2,000.

Jan 1, 1920