Search Documents

By E. W. Hawk

The power generation industry may be required to reduce CO, emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By Yongqin Zhang

A single bubble released into surfactant solution first accelerates, reaching a maximum velocity then decelerates to reach a terminal velocity. Modeling this "velocity profile" is fundamental to understanding the motion of bubbles in flotation systems. This contribution considers the terminal velocity. Modeling is by a combination of the Navier-Stokes equation for flow around the bubble and the Marangoni effect induced by surfactant on the bubble surface. Numerical simulation is shown to agree with experiment for bubbles in pure water and surfactant solutions.

Jan 1, 1999

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By K. F. Unrug

Extrapolation of the rock properties obtained from the cores exploration holes to the surrounding areas often causes problems because of frequent sudden changes in the geologic composition of strata. To address this problem, the author has been developing a method of rapid strength testing "in situ," with application of a borehole penetrometer. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. The results are generated by strength determination on the wall of a drill hole at a site. The newest development is a borehole penetrometer that requires only a 1.38.mm (1.5 in) diameter hole. The small diameter of the penetrometer body allows for drilling test holes with production mine equipment such as roof bolters. It opens the possibility of broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 1999

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By P. Somasundaran

Flotation of oxide minerals is controlled by a number of factors, such as surface potential and solubility of the mineral, concentration and type of various inorganics, properties of the collector, pH, ionic strength and temperature. The role these factors play depends on the mechanisms of adsorption of the collector inorganics or polymer additives. The major mechanisms include electrostatic interactions, chemical adsorption, chain-chain interaction between adsorbed collector species and modifications of the surface by inorganics. In real systems, flotation is, however, markedly affected by various other processes, including aging of the minerals, surface precipitation of the collector on the mineral and associative interactions between various collector species leading to highly surface active, for example, ionomolecular complexes. These effects are reviewed here with selected examples.

Jan 1, 1999

By G. France

The Blair Athol Coal Mine (BAC) is a large open cut operation in the Bowen Basin of Queensland, Australia. Current mine capacity is about 11 million tonnes per annum (Mtpa) of export coal. On-line analysis at BAC consists of two Coalscan 9500s installed directly on the output of the crusher plant and immediately before the product stockpiles, while a third Coalscan 9500 is installed on the transfer conveyor feeding the train loading bin. The two product Coals cans have a dual purpose. The first is to provide real time coal quality data directly back to the mining operations. The second is that of modeling the product stockpile with accurate on-line information. This modeling enables both production and coal quality personnel to accurately examine the coal quality of each stockpile with a degree of resolution which previously had never been achieved.

Jan 1, 1999

Capital budgeting and investment analysis have, to this point, been beyond the scope of this text. However, a recent conceptual development by John K. Shank and Vijay Govindarajan in the capital budgeting literature is of interest to operations managers because it (1) employs some of the cost management tools outlined earlier in this text and (2) provides a useful framework for using cost management techniques to improve the competitive position of the firm. ft Shank and Govindarajan present a method of analyzing proposed expenditures that is not based on discounted cash flow measures. Their approach employs a combination of three analytical tools: value chain analysis, strategic positioning analysis, and cost driver analysis. In each of these, cost and revenue information is used in ways normally not associated with conventional budgeting. Using this framework, capital projects are selected based on their ability to improve the firm's strategic position. Shank and Govindarajan have termed this approach "strategic cost management."

Jan 1, 1999

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

By T. van Sandwijk, G. Van Weert, E. Molleman

This paper reports on test work that explored the dissolution/precipitation reaction: ZnS + 2HCl - ZnC12 + H2S, which is part of a process used in the production of pure ZnS. The research focused on the influence of proton activity on the dissolution of zinc concentrates obtained from the Brunswick Mine No. 12 in Canada (Brunswick Mining & Smelting); the Red Dog deposit in Alaska (Cominco Ltd.); and the Tara deposit in Ireland (Outukumpu Zinc). A comparison between the results of the experimental dissolution as a function of pH and the dissolution predicted by thermodynamics suggest that the three concentrates contained sig¬nificant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1999

By James M. Barker

Marketing is the linchpin of the industrial-mineral (IM) industry. Without markets and consumers for IM products, all other associated IM activities are superfluous. The simple existence of an IM deposit does not mean that it can be exploited. A dynamic interaction between exploration (geology), mining, processing, transport, marketing, sales, and consumers is required for profits. Geology dictates the existence of a deposit, but markets dictate its development, and transportation provides the connection. This is true to such an extent that marketing commonly is called the exploration phase of IMs. Marketing is strategic and includes long-range market-development and planning activities, whereas selling is tactical and more focused on day-to-day consumer interactions. Each will help the other when properly done. Many producers of IMs have failed because of inadequate marketing skill, information, and practice. Over many years at the Montana Bureau of Mines, the many developers seeking technical assistance to find an IM deposit, but who had no marketing plan, always failed. In contrast, the few who sought assistance first on marketing, with the IM deposit to be found later, always succeeded (Richard Berg, personal communication, 1998). Marketing has many facets helped by geologists who must be aware of what marketing is attempting to do. A geologist needs to understand many aspects of IMs: location (deposits, plants, consumers), processing (specifications), transportation (truck, rail, barge, ship), competition (local, regional, national, international), substitutes, pricing, and new developments and market forces of all kinds. Some needed skills are not taught formally to geologists, so well-rounded self-education and on-the-job training are the way a geologist normally enters into IM marketing. The IM geologist generally is associated with marketing either by helping to prepare a market study or by acting on the results of one. Preparing a market study is a two-part process. The first part is relatively simple but requires a time-consuming collation of data into an IM survey (mostly past-and present-oriented). The more difficult and much more important second part entails expanding the IM survey into a market evaluation (mainly future-oriented) that emphasizes forecasting, timing, location, and specific products. A market evaluation generally boils down to formulating the right questions to ask of the right persons. One very good question to ask is, "What could be the market for this specific IM?" while thinking for yourself without excessive recourse to gossip, rumors, promoters, developers, or (at times) IM experts. The evaluation must prove that market potential exists and suggests a marketing plan. Effective marketing is an ongoing process, with the initial marketing plan modified over time, using wide and continuous input to avoid tunnel vision. Industrial-mineral markets are based either on commodity (lower-priced, basic-processing) minerals or specialty (higher-priced, value-added) minerals. IM marketing methods are either product-driven (commodity minerals), a more traditional approach, or market-driven (specialty minerals), but these are neither mutually exclusive nor is one always better than the other. Focusing too much on specialty minerals can lead to problems. A blend of commodity products with specialty products commonly lowers risk and enhances long-term profits. The highest profits occur in specialty minerals at the cost of higher risk and complexity and require intelligent marketing, versatile technical services, and creative research and development. Industrial minerals are best served by an industrial-marketing approach rather than a consumer approach. Modern industrial marketing emphasizes the consumer using the "marketing concept." The marketing concept focuses all management and operational activities on total consumer management and satisfaction similar to the total quality management approaches to excellence.

Jan 1, 1999

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By R. L. McNearny, K. A. Barker

A study was conducted to compare physical and numerical models of the block-caving mining method. Results from the numerical analysis closely simulated the blocky behavior of the physical model, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1999

By R. Q. Honaker

Until recently, the application of the Jameson Cell technology in North America has been restricted to minerals processing. Recently, laboratory, pilot-plant and full-scale testing has been conducted to assess the Jameson Cell's ability to effectively treat fine coal. Based on the data, carrying-capacity relationships have been developed. In addition to its operational simplicity, the Jameson Cell has the ability to provide a separation efficiency near the theoretical separation performance on the basis of ash rejection while achieving a relatively high throughput capacity Tie results obtained from the various fine coal cleaning applications in North America is presented in this publication.

Jan 1, 1999

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By Ray E. Harris

All of the major raw materials (silica, soda ash, limestone, and feldspar) needed to manufacture most grades of glass are found in Wyoming. Additional advantages for the manufacture of glass include the state's geographic location, a well-developed transportation network, a favorable tax structure (no corporate or personal-income tax), and low energy costs. Inadequate local markets and prohibitive transportation costs to other markets have been the major obstacles to developing a glass industry in Wyoming, the least- populated state in the nation. The Rocky Mountain region only recently became a major market for glass, especially for the Colorado Front Range and Utah's Wasatch Front. Currently, changing costs of the production of glass, an increased market for con- tainer glass in the Colorado Front Range, and innovative production and transportation ideas (e.g., production of selected types of glass and bulk shipments of specification-glass pellets) favor developing a glass plant in Wyoming. Thus, the Wyoming State Geological Survey (WSGS) and other state agencies have been conducting studies and contacting investors in an effort to attract a glass-manufacturing plant to the state. Between 1987 and 1993, three locations of silica-sand and -rock deposits were studied in Wyoming (Cassa, Plumbago Creek, and John Blue). Funding was provided by the WSGS operating budget and local and state Department of Commerce economic- development grants. The reports on these areas were released between 1988 and 1993. In 1988-89, a California-based company conducted additional drilling and feasibility studies and prepared to construct a glass plant in Cheyenne, using the Cassa silica source. However, due to losses incurred by some of their other investments, the company did not proceed. In 1997, the Wyoming Science, Technology, and Energy Administration (STEA) contracted a market study for glass manufactured in Wyoming, using information provided by the WSGS. The STEA contacted several major glass producers, and a major glass-producing company began feasibility studies in January 1998, for the construction of a glass plant. In June 1998, bids to supply brown beer bottles to the Budweiser brewery northeast of Fort Collins, Colorado, were submitted by at least two companies that were considering glass-plant sites in Wyoming.

Jan 1, 1999

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Osvaldo A. Bascur, J. P. Kennedy

Companies have installed powerful desktops for their personnel and instrumentation and control systems in their plants. These desktops are, in many cases, connected to a company intranet. Still, process engineers have to obtain their data manually. Engineers use process calculations from manually calculated averages from the plant; field operators collect equipment data on log sheets; and maintenance engineers collect critical information on log sheets. All of this information resides in individual machines. What are the strategic tools that will enable collaboration between them? How can operators, engineers, and managers access plant information to proactively increase their effectiveness in process troubleshooting, plant debottleneclung, aligning with business strategic and customer demand, satisfying environmental and safety regulations, developing capital projects, and implementing control strategies? A nonintrusive environment at the desktop is required to provide the process information to these workers. How can value be added to MS Windows technologies with the legacy systems at a minimum cost? There is no straight answer; however, there is a proven framework to leverage the large investments in new technologies. Objects and components are changing the way everyone relates to their computer and networks. Three examples will be described to demonstrate paradigm change. Today, process engineers can access data at the required level of detail for analysis of critical process variables at their desk or remotely. 1. Process Troubleshooting and Analysis: The engineer can develop an inferential calculation, trigger a process advisor to deter- mine the behavior of the units for the last day, and get the population of a set of batches (heats, blocks, rolls, sheets, etc). 2. Process Control and Optimization: The engineer can connect to a process simulator at steady state or a dynamic simulator of the process to evaluate new control strategies or process unit line-ups and use the process simulator as a process observer for fault diagnosis. 3. Collaboration with Accounting and Maintenance: The engineer can review reconciled data and the process mass balances, suggest maintenance cleaning or recalibration of flowmeters, and evaluate key control performance of all advanced controls.

Jan 1, 1999

Open pit optimization and mine design depend upon a realistic estimate of the grade-tonnage dis¬tribution. The estimate should reflect what can be reasonably recovered and processed. The McCoy/Cove operation in central Nevada is a gold and silver mine. Recoverable reserve estimations of gold and silver were made using indicator kriging and the indirect log normal variance correction to construct the grade- tonnage distribution. Optimal pits were generated using this distribution, and the results were compared to the pits generated by ordinary kriging and indicator kriging block mean methods. The results indicate that the proposed method for multimetal recoverable reserve estimation shows an improvement in terms of predicting the recoverable tons and grades. The optimal pits generated from the recoverable resource model are larger than those generated by the ordinary kriging and indicator kriging block mean methods. This model maximizes the overall recovery of the mineral resource.

Jan 1, 1999