Search Documents

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies. Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden, i.e., >30 m (100 ft), were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions

Jan 1, 1999

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By V. B. Achanti, A. W. Khair

Introduction Laboratory studies were carried out at West Virginia University to investigate the rock-fragmentation mechanism of continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be bit spacing, bit geometry, depth of cut and cutting-drum rotational speed. This paper presents a discussion of the effects of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation. The removal of rock ridges/walls between adjacent grooves is analyzed with three hits mounted simultaneously on the cutting head, while the bit tip angle was varied from 600 to 900. Bit spacing was varied from 25.4 to 50.8 mm (1 to 2 in.) while the cutting process was assessed for varying cutting depths. Respirable dusts generated during the course of the experiments were analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism of continuous miners in terms of energy consumption and dust generation. A review of the literature revealed that a considerable amount of research has been carried out on rockcutting processes. Many authors agree that the mechanical cutting efficiencies of mining machines (e.g., continuous miners, shearers and road headers) are affected by a host of parameters. Some of these parameters are machine controlled, some are operator controlled, while others are uncontrollable. Efforts were focused on understanding the influence of parameters such as bit spacing, cutting depth, attack angle, bit type, drum speed, bit geometry (i.e., tip size, shape and tip angle) and rock type on the cutting process efficiency in terms of specific energy consumption and respirable dust generation (Strehig?? et al., 1975, Hanson et al., 1979, Khair et al., 1989). Roepke et al. (1976) in an attempt to study the dust and energy generated during coal cutting using point attack bits found that the dust and the specific energy consumed both decrease as the depth of cut increases. The four fundamental stages of dust generation luring rock fragmentation are identified by Zipf and Bieniawski (1989). Coal breakage by various types of wedges was assessed by Evans and Pomeroy (1966) in an extensive experimental study on British coals. Yet the industry today requires further attention and guidance to optimize the energy consumption and dust generation during the rockbreakage process. This paper attempts to give a better understanding of the influence of some of the parameters listed above and focuses on further improvement in the rock-cutting process. The specific energy consumed for different types of bits used and the respirable dust generated are analyzed in the context of the variation of a few other parameters. Laboratory investigation The experiments were performed in the Rock Mechanics Laboratories located at West Virginia University. A rock-cutting simulator designed and fabricated by Khair (1984) was utilized for this purpose. The details of this machine are available in the literature (see Khair 1984). For this study, a series of preliminary experiments was carried out to determine the optimum cutting frame advance speed. This was intended to facilitate a maximum cut depth of 31.75 mm (1.25 in.) at an advance rate of 0.525 mm/s (0.0207 ips) for all types of bits being used and various bit spacings being considered. To look into the cutting-process efficiency of a continuous miner in the laboratory, several parameters of influence are being considered. Besides the bit-geometry parameters, machine- and operator-controlled parameters, such as spacing of bits on the cutting head, the cutting head rotational speed and the total cutting depth during an experiment, are varied. At the time this paper was written, only part of the completed experiments were ana¬lyzed, and a number of experiments were still being carried out following an orthogonal fractional factorial experimental plan to assess the effect of all of the above¬mentioned parameters on the cutting efficiency in terms of energy consumption and dust generation. Three different types of tip angles, namely, 60°, 75° and 90°, and two different tip sizes, namely, diameters of 7.94 and 24.61 mm (0.313 and 0.969 in.), were used. At

Jan 1, 1999

By R. M. Bricka, T. J. Olin

Heavy metals contamination is an environmental problem at Army installations engaged in firearms training and munitions production. At these facilities, weathering and corrosion of expended munitions and leaching from wastewater lagoons, landfills and burn pits have resulted in heavy metals contamination of the soil. The principal metals encountered in firing-range soils are lead, copper and zinc. Cadmium and other metals, such as antimony, that are often incorporated in the munitions are sometimes seen in lesser concentrations. Mercury is associated with various propellants and, while present in much smaller concentrations, is of concern because of its acute toxicity. Chromium is primarily associated with plating operations. The transport of metals into groundwater has been confirmed at some locations, which has required treatment of the soil and groundwater at these sites. Certain treatment processes for contaminated soil produce metals-laden extracts, which also require treatment before reuse or disposal. Ion exchange is generally quite effective for removing metals from aqueous streams. However, resins are expensive and must be regenerated, and activated carbon is generally less effective for most metals and also requires regeneration. Therefore, alternative effective and economic sorbents are needed. Twelve sorbents were screened in initial batch testing. These included activated carbon, bark, chitosan, crown ether, corn cob, xanthate, clay (kaolinite and montmorillonite), peat moss, seaweed and reagent-grade zeolite (aluminosilicate, Sigma Product No. Z3125). Of these, zeolite demonstrated the highest capacity for Pb, Cr and Cd. For this reason, zeolite was selected for further testing in batch, kinetic and column studies. Materials and methods Zeolite. The zeolite used in the second-phase batch and column studies was obtained from a natural deposit of clinoptilolite-rich rock located in South Dakota (Rocky Ford SDH) (Desborough, 1996). Large blocks of the material were crushed and sieved into the following three particle size ranges: 0.5 to 1.0, 1.0 to 4.0 and 2.0 to 4.7 mm. This material demonstrates high structural stability in acidic solutions (pH 2.5) (Desborough 1996) and has a measured surface area of 30 m2/g. The measured total cation-exchange capacity (TCEC) was approximately 10 meq/100 g. This is well below what has been indicated for commercially available zeolite, which has been reported to be about 180 to 220 meq/ 100 g. The TCEC test was repeated (Method 9081, SW 846) using sodium acetate. The test resulted in a TCEC of 54.5 meq/100 g. The difference between values obtained for this material and published values for zeolites may be attributable to the greater heterogeneity in the material used in this study, compared to commercially available materials, or to the effect of the relatively large particle sizes utilized. Batch studies. Seven batch studies were conducted using synthetic metal solutions and soil extracts (Table 1). Extract composition: The P-extract was prepared by sequential surfactant extraction of organics from a burnpit soil followed by acid extraction of metals. The pH of this solution is approximately 1.1. A number of metals and organic compounds were present in the soil. Analysis of the extract was restricted to Pb, Zn and Cu concentrations for this study. The FBH extract was produced from a firing-range soil that was oxidized with a 0.01 M CaO solution and then extracted with 0.1 M acetic acid. This was filtered through 0.5-µm Whatman No. 5 filter paper and stored at room temperature. The pH of the FBH extract was approximately 4.5. pH Control: Calcium carbonate (CaCO3) may be present in the zeolite horizon or bed. Calcium ion (Ca") is released from the exchange sites when in contact with solutions containing ions for which it is more selective, such as lead. This results in a rise in solution pH over time. Acid washing removes most of the carbonates, eliminating the need for a buffer. Batch studies were conducted using both acid-washed zeolite (AW) and unwashed zeolite (UW) for performance comparison. The UW zeolite was rinsed with distilled deionized (DDI) water to remove fine soil particles. Both materials were dried at 105°C (220°F) overnight, so that the dry mass could be determined. Column studies. Ten column studies were conducted. Because it was expected to have the best hydraulic properties, the largest particle

Jan 1, 1999

By Ing. E. h. Martin Herrenknecht, Werner Burger

In recent years, there has been a dramatic increase in the number of machine driven soft ground tunnelling projects. This increase is largely due to the technological development of slurry and EPB Shield systems. A new generation of soft ground tunnelling machines, markedly different from those of five years ago, now overcomes ground conditions that until now were too costly and impractical to undertake. The paper reviews the latest soft ground tunnelling machine developments in material transport, guidance and control, seismic surveying, soil conditioning, settlement control, cutting tool applications and variable mode operating systems. Specific projects where this technology has been applied will be highlighted.

Jan 1, 1999

By J. K. Neathery, T. X. Li, H. Ban, J. L. Schaefer, J. M. Stencel, X. K. Jiang

Pneumatic, triboelectrostatic processing of physical mixtures containing fine (-200 mesh) particulate may have significant application potential in the mining and energy industries. Such dry processing methods, especially for finely comminuted materials, have not been examined in as much detail as wet processing methods nor have been part of the training or education of mining and process engineers. We have examined fundamental and applied physical and engineering factors controlling triboelectrostatic beneficiation of fine-sized physical mixtures, one of which - combustion fly ash - has size, heterogeneity and mineral concentrations typical of those expected in mined minerals. The applicability of dry processing, however, cannot be readily evaluated because of the unavailability of standard procedures for process assessment.

Jan 1, 1999

By Ning Liu, Di Yin, Xuming Wang, Yongqiang Lu, Jan D. Miller

Air-sparged hydrocyclone (ASH) flotation technology has been evaluated for phosphate recovery from the central Florida phosphate deposits. As expected, it was demonstrated in pilot-plant tests that the ASH system has a specific capacity about 50-100 times higher than that of a traditional flotation cell. In the case of fatty acid flotation, single-stage ASH flotation produced a recovery of 75-77% in a rougher concentrate containing 24% P2O5 In reverse flotation with amine, the single- stage ASH system produced a phosphate recovery of 98% in a cleaner concentrate containing 31% P2O5. These results are comparable with those obtained at plant operations in the Florida phosphate industry. Based on these pilot-plant results, the effects of process variables are discussed in terms of separation efficiency. Subsequently, a 6-inch ASH system was fabricated and tested in a central Florida phosphate plant for reverse flotation in the amine flotation circuit. The high capacity of the ASH system was again demonstrated for the 6-inch ASH system. A single-stage phosphate recovery of 91% was achieved with a concentrate grade of 30% P205. During plant tests, it was established that porous tube plugging, the most significant engineering problem identified, was due to the poor quality of the plant water. Possible solutions to this problem are discussed.

Jan 1, 1999

By I. Iwasaki

Rest potential and linear potential sweep techniques were used to study the cathodic-polarization processes on chalcopyrite, simulating chalcopyrite short-circuited with grinding media in a wet grinding mill. Microflotation tests were carried out to investigate the effect of cathodic polarization on the collectorless flotation of chalcopyrite. It was observed that collectorless flotation of a cathodically polarized chalcopyrite sample could he obtained when oxygen was used for aeration, but not if nitrogen was used. A mechanism for the role that oxygen plays in the collectorless flotation of cathodically polarized chalcopyrite is discussed.

Jan 1, 1999

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision making when considering a methane drainage system for an underground coal mine. A drainage system entails significant capital and operating expense; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision making are provided for an actual mine decision.

Jan 1, 1999

By C. Yao, T. M. Yegulalp

The scale effect on rock properties has been discussed and studied since the introduction of the weakest-link idea by Weibull (1939). In this study, the capabilities of a dynamic lattice network model to simulate failure of rock under uniaxial tension is utilized. A number of randomly distributed microcracks that contribute to the development of uneven stressfields are introduced. In addition, each unit element in the model is assigned a random value representing its strength properties. Each application creates a randomly created specimen that is subjected to uniaxial tension. The specimens are grouped into three sets according to their size. The results of the study show that the scale effect is present in a statistical sense, i.e., the observed statistical distributions of strength for each specimen group is distinctly separate, and they follow the expected inverse relationship between strength and size. The observed probability distribution for each group of specimens give rise to the estimation of a different set of parameters. In this paper, the potential relationships among these parameters as a function of specimen size is investigated.

Jan 1, 1999

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999

By D. Einarson, B. Strickland

The decision to accelerate development of Stillwater Mining’s East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and RailSystems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km(3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By Daniel J. Dobbels, Eric R. Drooff, James R. Wheeler

Construction of Boston’s C11A1 Section of the Central Artery (I-93)/Tunnel(I-90) Project beneath the existing MBTA Red Line Subway at South Station required excavation to depths in excess of 33.5 m (110 ft) through permeable sand and gravel subject to almost 27.4 m (90 ft) of hydrostatic groundwater pressure. As tacked drift tunnel underpinning system was designed to provide positive support to the active station prior to mainline tunnel construction. As part of this system, a permeation grouting program was developed to facilitate tunnel excavation. This paper describes the design and implementation of the grouting program, in sit testing, and the overall performance of the grouted soil mass.

Jan 1, 1999

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By D. Kang, K. N. Han

The adsorption behavior of silver in ammoniacal solutions on activated carbon was studied. In addition to the concentration of ammonia, the parameters that affect adsorption include temperature, degree of agitation and anion and cation concentrations. In the study, it was found that the adsorption of silver from ammoniacal solutions is dependent on the initial silver concentration in the solution. It was also found that the recovery of silver from ammoniacal solutions is not as effective us gold. The adsorption rate was relatively slow overall, despite a rapid initial adsorption. The apparent activation energy ,for the adsorption was measured at 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1999

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. It is also a major exporter of minerals. Canadian open pits are highly mechanized and use state of the art equipment and support technology. During the past few years significant productivity improvements have been achieved by taking advantage of larger equipment; in pit crushing and conveying; truck dispatch systems and electronic management tools. The most recent developments in Canadian Open-pit Mining are related to hydraulic transportation and the application of Global Positioning Systems. Mine planning is computerized; environmental issues are dealt with in all phases of planning; equipment modifications are pursued with vigor to keep them functioning in the hostile Canadian North.

Jan 1, 1999

By K. Peri

The leaching behavior of gold in ammonical solutions with iodine as an oxidant has been investigated using cyclic voltammogram and Tafel polarization. The majority of experiments was carried out at 75°C and the results were compared with the equilibrium consideration on the iodine-ammonia system. The distribution of nine iodide containing species at various pH values in the absence and presence of ammonia was considered at three different temperatures. It was found that by introduction of ammonia into the system, the concentration of iodide (r), iodine (12) and triiodide (13') is increased substantially which in turn helps the rate of dissolution of gold. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical controlled mechanism.

Jan 1, 1999

By J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The Sao Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in 1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000 ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999