Search Documents

By R. Hogg

The factors which control the dewatering of fine coal by gravity/centrifugal drainage and by gas displacement (vacuum/hyperbaric filtration) are evaluated. A generalized model is presented and used to describe dewatering kinetics and to establish dewatering limits. Applications to the design of dewatering systems for fine coal dewatering are discussed.

Jan 1, 1995

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

By David G. Abbott, Frank Coluccio

This paper will discuss the construction of nearly 165 m (540 ft) of 3.5. m (138 in) o.d. reinforced concrete pipe to replace an existing utilidor under the Duwamish River in Seattle, Wash. The project required that two 27.4 m (90 ft) deep shafts be installed for use as jacking and reception shafts during the tunneling operation, and permanent vaults once completed. Soil conditions to be excavated consisted of soft saturated sand and silt with a 21.3 m (70 ft) water head. This required the shafts to be constructed using ground freezing techniques and the tunnel installed by pipe jacking, using a Mechanical Earth Pressure Counter Balance (MEPCB) slurry shield. The original utilidor was constructed between 1924 and 1925, and has since been deliberately flooded because it is considered to be structurally unsound.

Jan 1, 1995

By E. J. Sullivan

This study seeks to define the mechanism of oxyanion sorption onto surfactant-modified zeolites. Zeolites which have been treated with hexadecyltrimethylammonium bromide (HDTMA) surfactant to produce a hydrophobic surface are capable of sorbing both organic compounds as well as oxyanions such as chromate, selenate, and sulfate. Simple ion exchange and charge-balancing mechanisms do not fully explain this unusual phenomenon. The sorption of HDTMA surfactant appears to be partly ion exchange and partly sorption to non-ion-exchangeable sites. Sorption of chromate is a simple exchange mechanism with bromide, which co-adsorbs with HDTMA to form a surface precipitate. Information from this study will be used to design on-site and in situ treatment systems for contaminated water, such as filter beds and permeable barriers.

Jan 1, 1995

Mines in the Lake Macquarie region of New South Wales, Australia, are faced with the dilemma of having to introduce longwall mining techniques at a time when increasingly large areas of the surface are being used for urban development. Increasing pressures on safety, costs and productivity performance dictate that longwall mining is the method for the future. Construction of surface structures is controlled by a statutory body known as the Mine Subsidence Board (MSB). All surface structures have to be designed to MSB criteria. All mining plans involving secondary excavation also have to be submitted to the MSB for approval. The Board acts as risk assessor in evaluating acceptable levels of surface subsidence vs. the value of the coal resource. Surface repairs are paid for by a levy on all coal producers.

Jan 1, 1995

By C. E. Jordan

The Bureau of Mines has investigated the fundamentals of fatty acid/fuel oil conditioning for improved flotation selectivity. Both conditioning time and intensity can provide optimum flotation selectivity as well as good recovery. Traditional conditioning seeks to optimize conditioning parameters with subsequent recovery of the hydrophobic mineral. In the fatty acid/fuel oil system many silica gangue particles are also rendered hydrophobic by the flotation collector. Fundamental studies have shown that particle-particle collisions transfer the collector reagents selectively to the mineral surfaces with the highest affinity for the reagent. This mechanism deactivates the gangue particles while increasing the collector reagent loading on the selected mineral. The degree of this transformation is directly related to the number of particle-particle collisions which can be controlled through conditioning time or conditioning mixing intensity.

Jan 1, 1995

By Olli Järvinen

The precious metal refinery process is divided into the five process stages: 1 .copper/nickel leaching in autoclave 2. selenium roasting furnace 3. doré metal smelting furnace 4. silver electrolysis 5. gold recovery system. The process has been developed during the years in Outokumpu Harjavalta Metals, which treats about 600000 kg /year copper anode slime. The slime treatment process route in Outokumpu Pori plant has been developed from year 1941. During this period the process has been improved radically. The major changes has been the atmosphere leaching into the autoclave leaching, the sulfuric acid roasting furnace was changed into sulfuric dioxide / oxygen roasting. The old doré smelting furnace has changed into the TROF converter and the gold electrolysis / aqua regia process has changed into the quick hydrochloric acid leaching process. The current production in Pori plant is 30000 kg of silver, 1000 kg gold, 30000 kg of selenium and some hundred kg of platinum- palladium concentrate.

Jan 1, 1995

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

By M. A. Giralico

Solvent Extraction (SX) technology has undergone significant refinements including outright process changes to achieve greater copper production rates with lower organic entrainment levels. LIGHTNIN has completed a detailed study aimed at improving on the conventional Holmes & Narver and Davy Power Gas type impeller designs1 by optimizing the mixing through the use of high efficiency pumper turbines instead of making system changes as others are doing. Since each individual installation requires a different design head and flow, LIGHTNIN has developed the R320 "family" of high efficiency, curved blade pumper turbines. These impellers are designed to maximize head and flow while reducing entrainment through lower power consumption, less shear generation and turbulence, elimination of air incorporation, production of the optimum droplet distribution, and lower tip speeds. These improvements also maintain the required mass transfer and copper recovery of the traditional impeller designs. The R320 impeller benefits have been quantified using Laser Doppler Velocimetry (LDV) and proven in multiple domestic and foreign installations at flow rates exceeding 15,000 GPM. Design comparisons of this improved impeller type versus traditional technology impellers in head, flow, power and entrainment are presented for review. In addition, the inherent benefits of axial flow, high efficiency impellers like the A3 1 0 and A6000 in auxiliary mix chambers will be discussed. The high flow, low shear characteristics of these patented impellers provide the necessary dispersion stability for mass transfer while speeding phase disengagement in the settlers due to low power and low shear input.

Jan 1, 1995

By H. Lyn Bourne

The is the 14th consecutive year for this column and the 13th in which the royalty data have been tabulated. Some holes still exist in the list of royalties that readers hopefully will fill. Construction aggregates - either sand and gravel or crushed stone - are the most common mineral commodity. In spite of their pervasive use nationwide, royalty information for these commodities has been difficult to acquire from some states. Readers can help. Share information about these missing states and next year there will be fewer states without information. Dennis Bryan sent a copy of a report, "Regional Appraisal of Mineral Materials: Carson City District, BLM." The report was authored by real-estate appraisers. It contains more than 50 references to leases of various construction materials in Nevada and nearby states. It gives a thumbnail sketch of each lease and is a good reference. However, the authors erroneously imply that the royalty rate and the in-place value are the same. Several of this year's new entries come from the report. However, the royalties for landscaping materials vary from state to state and by rock type. Some boulders used for landscaping in Nevada have a royalty reported at $1.10/t ($1/st). At the other extreme is lava from Idaho. Used for the same purpose, it has a royalty range of $11 to $18.70/t ($10 to $17/st). Chuanming Tian of Beijing, China has shared some information about the changing mineral royalty policies in China. China first implemented an oil and gas royalty in 1984. In 1992, the government expanded that to include iron ore. In 1994, the royalty policy was extended to all mineral commodities. At the same time, the royalty rate for iron ore increased tenfold.

Jan 1, 1995

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

Continuous improvement has become the watchword of the 1990s for most iron-ore-processing operations. In many instances, this improvement has been achieved through stepwise application of advanced control techniques to optimize operations. The benefits of this stepwise application have been great. However, they have fallen short of the full potential offered by the prospect of overall plant optimization. The successful integration of computers, instrumentation and control software throughout a plant promises to deliver an additional 3% to 5% of productivity in even the best-run plants (Herbst and Bascur, 1984). LKAB is Europe's largest iron-ore producer and a leading implementer of advanced control technology. In the late 1980s, LKAB introduced advanced control in its concentrator at Kiruna, Sweden to improve plant performance through higher productivity, greater efficiency and lower costs at each processing step.

Jan 1, 1995

By T. W. Camm

In this US Bureau of Mines report, mine and mill cost models are presented to make estimates of the cost to develop mineral deposits in the desert region of the southwest United States. Regression analysis was used to generate capital and operating cost equations for each model based on daily production capacity. These models are used for Potential Supply Analysis (PSA) studies by the Bureau, which analyzes the economic benefits of minerals in a region.

Jan 1, 1995

By D. W. Park

Artificial intelligence has emerged over the past two decades as an important problem-solving tool including techniques such as expert systems, neural networks, tree classification, fuzzy logic, genetic algorithms, etc. These methods can be employed to solve rock mechanics and ground control problems associated with the highly complex nature of rock masses and ground conditions. A current study at the University of Alabama focuses on development of an artificial intelligence system for real-time interpretation of the data collected from longwall monitoring stations, and development of an early warning system for prediction of undesired conditions and prevention of longwall-mine instability problems. This paper describes a ground control management system using UALSAS (The University of Alabama Longwall Stability Analysis System), which is being developed to facilitate maintenance, on-line analysis, prediction, and includes an early warning system. A detailed framework of computer algorithms and their applications are also discussed. The successful application of these artificial intelligence techniques will contribute to a safer and healthier mining environment.

Jan 1, 1995

By David M. Spatz

Ore deposit models are defined largely by physical geologic features that relate conveniently to remote sensing. New Landsat, SPOT, RADARSAT and other multispectral and hyperspectral sensors with improved spatial resolution are currently in development. Near-infrared and thermal airborne hyperspectral scanners hold outstanding promise for both mineral exploration and feasibility stage mapping at potential new mining projects. These scanners are capable of identifying silicification, differentiating silicate alteration types, and mapping compositional variations within igneous and metamorphic complexes. Research in 'mineral and rock spectrometry is helping to advance applications of remote sensing. Hyperspectral scanners are capable of differentiating compositional variations within individual mineral species. Innovative data processing techniques continue to enhance computer software applications and facilitate imagery analysis by the geologist. Today, . remote sensing imagery is commonly integrated with multiple data sets in GIS format to form the core data base for regional exploration programs.

Jan 1, 1995

By Chen Bingchen, Zhang Jian, Liu Jiaxiang

The influence of various installation angles of hydrocyclone on its operation indexes was investigated, and the correspondent mathematical models were established in this paper. The models developed in this paper can be used to the optimizing control of hydrocyclone and make the hydrocyclone as a particle size sensor.

Jan 1, 1995