Search Documents

By Jeong-Heum Kim, Jan M. Mutmansky

A number of solution methods for solving the nonlinear equations derived from mine ventilation networks use meshes selected from the network as the basis of the solution techniques. Mathematicians working in network theory have outlined several methods for speeding up the computations through mesh selection and ordering procedures. In the mine ventilation area, a fair amount of attention has been paid by ventilation specialists to procedures for choosing the meshes so that the computational effort is eased. However, little attention has been paid to mesh ordering methods. This paper outlines research into random mesh ordering procedures plus two non-random mesh ordering procedures and compares some results using these procedures within four solution algorithms.

Jan 1, 1993

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By Brian Hester

Many Third World African countries are well-endowed with minerals - especially gold and diamonds - while only a few have important base metal deposits. For decades since colonial rule, political and economic conditions discouraged interest by Western capital. Influence from Soviet Bloc countries, however, has declined with the move toward multi-party rule. And the left wing orientation, once widely favored by Third World African countries, has almost disappeared. With International Monetary Fund (IMF) encouragement, these Third World African countries now encourage representational government and solicit western finance to expand their industries. Mining is especially encouraged. The North American mining industry is following the same trail as other capital intensive industries and looking abroad for opportunities. The Prospectors and Developers Association of Canada released figures that show exploration expenditures in that country were halved between 1987 and 1990. Figures for the United States are not so easily found but every indication points to a downward trend. While total annual expenditures on US exploration by corporations as a group are either declining or remaining constant, expenditures away from North America is increasing. Gold exploration expenditures in 1991 by the major companies tracked by Minerals Economics Group were less in the United States than for Latin America and the Southwest Pacific combined. The same study showed as much was spent in the Republic of South Africa and "Other" areas combined as in the United States. Expenditures by major corporations in these "Other" areas amount to only 5.2% of their total budget. Third World Africa is a major component of these "Other" areas.

Jan 1, 1993

By W. C. Lacy

Traditionally Australia has been a leader in underground mining methods with world standards being established at Mount Isa, Broken Hill, Kalgoorlie, and Mount Lyell. With decline in higher-grade reserves and discovery of a multitude of near-surface oxide gold de-posits attention has shifted to bulk mining of low-grade gold ores by open pit methods, heap leaching and activated carbon recovery of gold values. The paper examines historical change in mining philosophy and the economic effects of isolation.

Jan 1, 1993

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

By W. M. Shaver, W. R. Dengler

INTRODUCTION In Canada, most of the rock being broken in underground metal mines is being carried out using traditional drilling and blasting methods. Despite advances being made in hard rock boring and other, more exotic techniques, it is Dynatec's belief that the traditional methods will continue to prevail for many years to come. It is also our belief that modest research efforts expended on the traditional methods will result in substantial financial benefits to the mining and rock tunnelling businesses. Dynatec has pursued productivity improvements through the use of long rounds in both shaft sinking and lateral development. The concept of longer rounds was developed by Dynatec on the Craig Shaft Sinking Project (RETC 1991). This paper reviews the Craig Shaft Long Round success. This technology was subsequently utilized to sink the two shafts at Aur Resources with great success. The development of a Long Round Jumbo for tunnelling is a natural progression of the long round technology developed for the Craig Shaft. RECENT HISTORY OF SHAFT SINKING Shaft sinking is one of the oldest and most difficult mining methods. Due to the relatively small amount of shaft sinking in proportion to tunnelling and

Jan 1, 1993

By K. R. Miller

Thunder Basin Coal Company has two mines located in the southern portion of the Powder River Basin. 60-90 km southeast of Gillette, Wyoming. The mines are principally located on federal coal leases acquired in the late-1960's. Development plans for the Black Thunder Mine focused on dragline stripping, but environmental considerations during the mid-1970's made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lying with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age and the deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21 m thick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By Jean-Luc Cornet

As modern conveyors are increasing in size and complexity, their control requirements are becoming more and more critical. In addition to the safety and equipment protection requirements, control systems are now called to implement intelligent drive controls derived from dynamic analysis modelling, as well as to provide fast and accurate diagnostics while keeping operator controls simple. These requirements led to the development of a new and innovative approach to control system development. This paper describes the control philosophy used by Conveyor Dynamics, Inc. (CDI) and some of the key features of our approach to the architecture of control systems.

Jan 1, 1993

By John R. Marks

The first 0.7 m3 (1 cu yd) diesel load- haul-dump vehicle (LHD) arrived at the Homestake Gold Mine in Lead, SD in I969 to muck a ventilation drift. Others soon followed. Mechanization has subsequently changed stoping methods, manpower requirements, ventilation practice, the definition of minable reserves, and it has impacted safety and health. These have all had a direct bearing on the economics of producing gold ore from deep underground. Mechanized mining Before mechanization, production quotas at Homestake were met by several open cut-and-fill (OCF) mining methods. OCF mining relied on jackleg and wagon drilling, electric and compressed air slushing and cribbed raises brought up through the fill. Even square- set stoping was used until about eight years ago. The mine became 100% mechanized in 1988. The two current stoping methods are mechanized cut-and-fill (MCF) and vertical crater retreat (VCR). In 1992, MCF accounted for 54’S, VCR for 44% and development/uphole for 2% of the 1.4 Mt (1.55 million st) of underground ore produced. These methods are typically ramp- based and use diesel-powered LHDs, trucks, pneumatic drill jumbos and utility vehicles. Electric LHDs and rubber-tired compressed air muckers have also been used in VCR scrams. Pfarr (1991) and Mitchell (1980) provide good overviews of current production methods.

Jan 1, 1993

By V. D. Smar

The flotation process may be considered an interactive system consisting of many chemical, operational, and equipment variables. Changing anyone of these variables causes an overall system response change. This study examines the effects of simultaneously changing the operating variables of: (1) frother concentration and air flow rate, and (2) frother concentration and collector concentration. It is part of a comprehensive study to look at how changes in several of the major variables may be used to produce interactions which will allow the rougher flotation process to be optimized. Ultimate recovery, flotation rate, concentrate grade and froth quality, are used as the major evaluative criteria.

Jan 1, 1993

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By Y. M. Jiang, D. W. Park, S. M. Lee

A vast majority of longwall operations in the US use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional, finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite-element model of the shield structure was made to study responses of each longwall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested that a technique incorporating the finite-element method be developed to evaluate real-time shield performance for the purpose of effective ground control.

Jan 1, 1993

By M. L. Matt

The Pittsburgh Safety and Health Technology Center of the Mine Safety and Health Administration has developed the Mine Emergency Responsiveness Development (MERD) program to improve the reaction and response of mine personnel in mine emergency situations. The MERD program simulates problems that may be encountered in underground mine fires, underground mine explosions or surface mine accidents. Since its inception in 1982, the MERD program has been presented to MSHA, Industry, Labor and State Government Personnel. The program is extremely versatile and is easily adapted to suit various training requirements. It gives the participants the opportunity to experience some of the emotions, frustrations and successes of a mine emergency in a controlled environment without having to be involved in one. Past participants have indicated that this training has better prepared them in actual emergency situations through increased awareness and advanced preparation of plans and resources. In 1992, a Mine Simulation Laboratory, which simulates a coal mine and metal/nonmetal mine, was built to improve training for mine emergencies and prevention and fighting of mine fires. This facility has been included in the MERD Program to provide realistic and practical training for mine rescue teams and MERD participants in advanced mine emergency operations. This paper presents an overview of the MERD program.

Jan 1, 1993

By M. C. Baumann

The Getchell Mine is located in Humboldt County, Nevada, approximately 70 km northeast of Winnemucca. Slope management has been a critical factor in the feasibility of mining operations since they began in the early 1930's. Although underground entries began in 1937, underground production was limited because hanging walls consisting of clay gouge and crushed rock tended to collapse into the workings. Controlling these collapses required extensive timbering. Due to these poor ground conditions, surface open-pit mining was the primary mode of production from 1938 to 1967 with only minor contributions from underground operations. Mining was suspended in 1967 due to economic pressures. From 1960 to 1967, the previous operator mined the property in three open pits. Initially, these pits were constructed with footwall benches, but these failed. These failures were aggravated by construction of 60° slopes in footwalls with shale partings dipping into the pit at 43° to 60°, resulting in large planar failures and wedge failures. In response, the previous operator adopted a slope parallel to the bedding planes.

Jan 1, 1993

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

By R. V. Ramani, S. Tan

In this paper, several commonly used computer truck-dispatching criteria are evaluated. A computer-oriented truck-dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. However, several dispatching criteria that have good potential to increase performance can be identified. All basic dispatching criteria, including minimizing truck waiting time, waiting shovel with minimum waiting time, minimizing truck saturation, maximizing truck momentary productivity or optimization of truck routes, provide local optimal solutions. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. It may be necessary to search for a hybrid combination of the several truck dispatching criteria that have good potential for a given situation. An approach to selecting such a hybrid dispatching criterion is presented.

Jan 1, 1993

By J. Chia, M. H. Kobler, J. Cheung, M. J. Robison

INTRODUCTION The Lake Merced Transport is being constructed as part of San Francisco's Clean Water Program. The Clean Water Program, which began in the early 1970's, is designed to control wet weather, storm sewage overflows into the Pacific Ocean and San Francisco Bay. To accomplish this goal, a system of large underground storage and transport facilities, pump stations, modernized treatment plants, and outfalls is being built. By 1991, eighty percent of the system had been completed and was in operation. One of the remaining projects for the Clean Water Program is the Lake Merced Transport. The Lake Merced Transport is located in the extreme southwestern portion of San Francisco, as shown in Figure 1, Project Location. The transport will convey dry weather flow from the existing Lake Merced Pump Station to the Westside Pump Station. During wet weather, the transport will fill with sewage and runoff, with a storage capacity of 36 million liters. The Lake Merced Transport was expected to be excavated entirely within the Colma Formation, an alluvial deposit consisting of weakly cemented sand. Once excavation of the access portal at the Sloat/Great Highway parking lot began, it became evident that a portion of the tunnel would be excavated through beach/dune sand. Based upon the expectations of the Geotechnical Design Summary Report (GDSR), encountering beach/

Jan 1, 1993

By R. Y. Wan, Corby G. Anderson, L. Ernest Krys, M. C. Fuerstenau

Since 1942, refractory precious metal concentrates at the Sunshine mine have been processed for antimony metal recovery using a novel leach-electrowin method. This is counter to most antimony production facilities where pyrometallurgical techniques are usually relied upon. The key step for removal of the antimony has been an ambient pressure alkaline sulfide leach. In 1990, a comprehensive laboratory study was undertaken to better understand this process. Factors studied included temperature, agitation, concentrate regrind, alkaline species concentrations, sulfur species concentrations and solids concentration. Details of these studies, as well as a brief description of Sunshine metallurgical processes, will be presented.

Jan 1, 1993

By D. Gatzemeier

The Jewett mine is a surface mine in central Texas, producing about 8,000,000 tons/year of lignite. The mine covers 46,000 acres of land. Approximately 430 people are employed by Northwestern Resources Company and through their efforts, the Jewett Mine is one of the most productive mining operations in the country. The Jewett Mine utilizes a unique structure of staff to convert Operations Research into plans which can be implemented at the "front line" level of the Operations Team. This planning not only makes the mine cost effective and efficient, but promotes creativity in mining, which promotes ongoing research to lower the cost of mining.

Jan 1, 1993