Search Documents

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By S. K. Kawatra, S. Valluri

With increased CO2 emissions from steel and coal industry, there is great opportunity to capture CO2 and utilize the captured CO2 for economic advantage. The primary goal is to develop energy-efficient processes that reductively couple CO2, an abundant and renewable carbon source, for the production of value-added chemicals such as methanol, ethanol, and oxalic acid. These chemicals can be used elsewhere in the refining process or sold as valuable by-products. Geological sequestration, in comparison, has no economic return. Current CO2 utilization research at Michigan Technological University focuses on electrochemical reduction of CO2. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. This paper will present different ideas and their viability to utilize CO2 as a feedstock to produce several value-added compounds. INTRODUCTION Carbon dioxide (CO2) emissions into the atmosphere will need to be drastically reduced to curb the various undesirable effects of climate change. The large contribution in total CO2 emission originates from coal or natural gas power plants, and a considerable amount from steel plants. Average CO2 emissions in the US from steel industry is 2.9t CO2/t steel (Global CCS Institute 2013). Capturing the available CO2 from the steel and coal industries for economic advantage is a win-win situation for the industry. This technology is not only important scientifically but is also vital for a sustainable future. The various ongoing investigations can be categorized as biochemical, thermochemical, photochemical, and electrochemical approaches. Among these, the electrochemical method shows the most promise as an efficient form of CO2 conversion technology, because of its many advantages like high reactivity under ambient conditions and good extensibility from small- to large-scale processes1 BACKGROUND Extensive research has been done on the chemistry of transforming carbon dioxide into more useful products. Methods are known to convert carbon dioxide into a wide variety of substances, including methanol, isobutanol, carbohydrates, methane, carbonates, urea, formic acid, oxalic acid, carbon monoxide, epoxides, formaldehyde, and so on. Several of these (carbohydrates, formaldehyde, isobutanol etc.) are primarily results from biological processes. The rest are results of strong reduction reactions or electrolytic reduction. In short, electrolytic reduction can be used to form methane, methanol, formic acid, oxalic acid, carbon monoxide from carbon dioxide2. CO2 reduces at the cathode in an electrolysis cell. These processes have the general form of generating the carbon dioxide anion radical (2⋅−) and allowing it to react with itself or the electrolyte3. Catalysts can be added to influence the formation of the anion radical or to suppress side reactions3. The electrolyte, catalyst, voltage, electrode material and CO2 content are all known to effect the reaction pathway. Table 1 shows the overall reactions and energy requirements for electrochemical conversion of CO2 to chemicals

Jan 1, 2019

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud. INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1].

Jan 1, 2019

By A. Porvali, V. Agarwal, M. Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2•H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can be treated further with NaOH solution to form REE hydroxides. This study focuses on metamodeling of a simulated flowsheet with design of experiments (DOE). Based on literature survey, a process flowsheet was developed using HSC Sim software. The created flowsheet focuses on circulation of solution containing Na+, K+, SO42- ions and impurities liberated in the NaOH treatment of double salt precipitate. The effect of seven parameters (P1-P7) on seven responses (R1-R7) were modeled using central composite design (CCD). INTRODUCTION Nickel metal hydride (NiMH) battery waste can be considered as an urban mineral due to the presence of valuable metals like: Ni, Co and rare earth elements (REE) (Larsson et al., 2013). In NiMH battery waste leaching experiments, sulfuric acid has often been employed as a lixiviant (Pietrelli et al., 2002,Zhang et al., 1999,Rodrigues and Mansur, 2010,Porvali et al., 2018). The key advantages of sulfuric acid are its stability and cost-effectiveness compared to other mineral acids such as HCl and HNO3. However, the usage of sulfuric acid in NiMH battery waste leaching poses simultaneous challenges and advantages. Limited REE solubility can be taken as benefit when recovering REEs double sulfates after solid-liquid separation. However, sodium and potassium hydroxide, present in electrolyte residues in the battery waste, can cause in-situ precipitation already during leaching due to limited solubility, thus decreasing the total REE recovery (Porvali et al., 2018). However, this problem can be circumvented by washing the electrolyte residues off the raw materials. Subsequently, the REEs may be precipitated in bulk as a mixed double salt out from the solution at very low pH with minimal co-precipitation of Ni and other metals. This relatively easy separation method can be extremely advantageous in the case of such a complex solution matrix with relatively high REE concentrations (conc.). Once REEs have been precipitated as double sulfates as per eq. (1) (Porvali et al., 2018), the resulting double salt precipitate lacks applications without further treatment. Direct thermal treatment would generate sulfur dioxide emissions and likely require high temperatures in order to transform double sulfates into REE oxides. Furthermore, the precipitate contains Na ions, which would need to be removed by chemical treatment from the calcined REE product. In the context of circularity of raw materials, it can be taken of a remarkable benefit if the sodium and sulfur present in the double salt could be reused instead of wasting them into the side streams. To that end, in this simulation study, the double salts are converted by dissolution and precipitation to hydroxides which are readily treatable, e.g. with total dissolution and solvent extraction, for further purification (Abreu and Morais, 2010):

Jan 1, 2019

"Twin Creeks is a gold mining complex that is part of Newmont’s Nevada operations. The mining complex is composed of two openpits, Mega and Vista, external ore sources and a set of existing stockpiles, all of which provide ore for an autoclave, an oxide mill and a heap leach. Mega pit provides sulfide ore for the autoclave, whereas Vista pit provides oxide ore for the oxide mill and the heap leach. Both pits operate the same mining equipment and their extraction sequence must, therefore, be optimized simultaneously. Stringent blending requirements are associated with the operation of the autoclave for the sulfide ore. Strategic blending optimization on a large scale has brought significant value to the operation by increasing synergies. This paper presents the implementation of a stochastic optimization framework for the long-term production planning at Twin Creeks that simultaneously optimizes mining, stockpiling, blending and processing decision variables. The uncertainty and variability associated with the different sources of material are incorporated in the optimization model by means of stochastic simulations. The stochastic solution generated shows substantial benefits by increasing forecasted recoverable gold, leading to increased cash flows, while reducing the risk of not achieving forecasts by increasing the probabilities of meeting production and blending targets.IntroductionMine operations consist of multiple components such as mineral deposits, stockpiles, external sources, mills and autoclaves. These components represent a mineral value chain, also known in the literature as a mining complex (Montiel and Dimitrakopoulos 2015; Goodfellow and Dimitrakopoulos 2016). The material extracted from the mines flows through the different components and is transformed into sellable products. This flow of material in a mineral value chain involves complex, nonlinear transformations that render the use of industry-standard optimizers difficult. Furthermore, the optimization of a mining complex can be formulated as a mixed-integer, nonlinear optimization program with millions of integer variables representing mining, blending, stockpiling and processing decisions, prohibiting the use of conventional nonlinear optimization approaches. Previous methods that consider the joint optimization of multiple components of the mineral value chain are available (Hoerger, Seymour and Hoffman, 1999; Chanda, 2005; Stone et al., 2005; Wooller, 2005; Whittle, 2007, 2010; Bodon et al., 2010). Although these methods add value by increasing the synergy between the different components of the mining complex, they rely on simplifying assumptions that constrain their efficacy, while ignoring a most critical aspect. The latter aspect includes the geological uncertainty and actual variability of the materials in the mineral deposits mined and are supplied to the related mineral value chain, similarly to conventional life-of-mine planning methods used for individual mines (Dimitrakopoulos, Farrelly and Godoy, 2002; Godoy and Dimitrakopoulos, 2011; Spleit and Dimitrakopoulos, 2017). Additional simplifying assumptions may include: the consideration of a limited number of components, the combination of different methods, the aggregation of variables, fixed production schedules the definition of policies prior to optimization, such as cutoff- grade definition or destination of mining blocks, the linearization of nonlinear transformation functions and/or the disregard for the uncertainty of several critical parameters (Whittle, 2007). The simultaneous optimization of multiple components of a mining complex was introduced by Newmont. Hoerger, Seymour and Hoffman (1999) implemented a mixed-integer programming formulation to optimize Newmont’s Nevada operations. The model is based on the work of Urbaez and Dagdelen (1999) and simultaneously optimizes the extraction of materials from multiple deposits and the delivery of ore to multiple plants, as well as as"

Dec 1, 2018

By Rick Frechette, Greg Nelson

"The 2018 Elko Roundtable was held at the Red Lion in Elko, NV on March 15, 2018. The gracious host was once again Knight Piésold. Attendance was robust with representatives from more than 14 mining properties across Nevada representing nine corporations. Total attendance was at its highest in almost a decade. A high level of interest was also gauged by the number of companies with multiple attendees.The topic of water in mining was clearly a factor in creating the large show of interest. In terms of industry trends that are tracked annually, this topic had been absent from the list for more than 10 years (Deloitte, 2018) but was squarely planted there this year. And deservedly so. Three attending companies are signatories of the International Council on Mining and Metals (ICMM) which espouses a firm stance on water stewardship (ICMM, 2017).How’s the water?It is reported that water scarcity affects more than 40 percent of the world’s population (Deloitte, 2018). Consumption of water in the United States, based on the last detailed census, entails only 1.5 percent usage by the mining industry. The largest users are reportedly thermoelectric power and irrigation, combining for more than 75 percent of the U.S. consumption. During the prior census period, water usage at mines was up dramatically (USGS, 2014).Mine water source usage is primarily a mix of ground water and saline or fresh surface water resources. Over the previous period, saline sources experienced the greatest percentage in growth as a mine water source, nearly doubling in use. Nevada ranks second as a state nationally in mine water consumption. California is the leader, and Nevada is immediately followed by Utah and Alaska (USGS, 2014).Water rights in Nevada and the ongoing litigation at the state level, particularly over the Humboldt River basin, have elevated the concern over the supply of water and have raised the interest regarding the topic of water across the mining industry as well as within other industries.The Elko Roundtable meeting began with a safety share and introductions, and included each attendee mentioned a water problem or solution that he or she would like to discuss during the day. An interesting list of subtopics was developed from this round robin and yielded the following most common themes:• Mine pit dewatering during operation and pit wall stability.• Draindown from tailings dams and heap leach pads and dealing with this at closure.• Post closure pit lakes, pit lake water quality and associated water rights."

Dec 1, 2018

By Steve Kral

"Repairing and replacing the nation’s aging and crumbling infrastructure has become a major issue with the American public. It is no secret that the upkeep of roads, tunnels, bridges, and water and waste water facilities has been neglected for decades. Cities, states and towns across the United States are now grappling with these issues, ones that will take decades and billions of dollars to fix.Because of this infrastructure issue, the North American tunneling industry is flourishing. Cities across the country are looking to go underground to alleviate traffic issues, transporting water and waste water to more people in more efficient ways.In October, the seventh annual Cutting Edge conference was held in Atlanta, GA. Put on by the Underground Construction Association of SME and Britain’s Tunnelling Journal, about 175 tunneling and underground construction professionals from around the world attended. Attendees included owners, designers and contractors. An accompanying exhibit included 28 companies.The theme of the two-day conference was Advances in Tunneling Technology. Speakers examined the latest advances in tunneling technology, its methodology and how these advances can be harnessed to assist upcoming major tunneling projects. The conference featured a tailored, high-end, single-track program of subject-specific presentations that focused on innovation and practical experience. Two in-depth panel discussions at the end of each day were also included.Patricia Mulroy was a keynote speaker on Monday. She is senior fellow for climate adaptation and environmental policy at The Brookings Institution. Like many others, Mulroy believes the U.S. infrastructure in in a state of disrepair. But, she said, no one wants to talk about it. “We need to have a conversation about infrastructure. We cannot be afraid to talk about building it and the cost.” For this to happen, though, the nation needs leadership."

Dec 1, 2018

By Daniel Lakovic

"Mining operations can create a negative environmental impact, especially when considering the tailings that are produced through the processing of ores. Tailings are finely grained residues that form sludges. The tailings are deposited into giant basins, or sludge ponds, where they create a burden on the environmentby limiting the use of processed water.Tailings are one of the most important environmental liabilities for mining operations because of their large proportion in relation to the ore mined — generally 90 to 98 percent. To get to the valuable minerals, mining companies must move large amounts of rock. The rock is ground and then treated, usually with the addition of chemical solutions and large amounts of water. The lower the concentration of the valuable resources, the greater the proportion of accumulated excavated material sludge.Sustainable tailings management requires responsible handling, making it one of the mining industry’s greatest challenges. The proper technology should include consistent control of the environmental risks and impacts, as well as a proper relationship with the communities that surround the mining operations.The tailings, which can remain partly contaminated with chemicals, are pumped into the large sludge basins, which are secured by earthworks. During the mining operations, the basins must be stable enough to withstand the pressure of the stored excavated material. The storage option is still used, but it has failed on occasion. And when it does, it increases the risks to the environment and binds the unused process water. The more complex the availability of fresh water required for industrial use and for human consumption and their economic activities — for example, farming and agriculture — the more complex the conflicts that have the potential to shut down mining operations. With modern separation technology solutions, it’s possible to process the sludge and recover the processed water. However, the responsible use of the water is critical. Therefore, mining companies must rely on technologies that allow for proper reclamation of the water, whether re-using in their own processes or treating it to return it to the environment."

Dec 1, 2018

By William Gleason

"Caterpillar is the largest manufacturer of mining equipment in the world. In hundreds of surface mines around the globe, Caterpillar’s flagship 793 haul trucks can be found moving material for copper, coal, gold, iron ore and other mines. Likewise, its iconic yellow bulldozers are at mine sites the world over — the company recently announced the sale of its 40,000th large dozer. And since its acquisition of Bucyrus in 2011, Caterpillar has positioned itself to become a worldwide leader in the underground mining sector as well.But don’t think that the company is resting on its reputation. As evidence of its commitment to the global mining sector, as well as its confidence in the future of mining, Caterpillar invited mining trade press, including Mining Engineering, to its Tinaja Hills Training Center near Tucson, AZ in November to introduce the latest editions to its mining portfolio. The two-day event focused mostly on the newest electric drive haul trucks, the Cat 796 AC, which will operate in the 326-t (360-st) class, and the 798 AC in the 360 t (400 st) weight class.Caterpillar representatives also spoke about new offerings in the underground space as well as the newest version of the D11 large dozer.“It has been 10 years since we launched the F Series,” Jean Savage, Caterpillar’s vice president, surface mining and technology said. “Since then, we have been on a journey to serve our mining customers and we wanted to have trucks in every application. Today, we are launching two new trucks that will allow us to fill out our portfolio.”While Caterpillar previously offered the broadest range of off-highway haul trucks to the mining industry, it was noticeably absent from the 326-t (360- st) and 360-t (400-st) weight classes."

Dec 1, 2018

By William Gleason

"Komatsu has been on the cutting edge of autonomous mining for the past 30 years and the company remains at the forefront of the technology that is changing from concept to a full-fledged reality.In 1996, Komatsu America Corp. (KAC) purchased a controlling interest in Modular Mining Systems; a move that enabled both companies to expand their product lines. It was through this effort that Modular helped to deploy the first autonomous haulage system (AHS) — the Komatsu FrontRunner system. In January 2008, the first commercial implementation of the FrontRunner system occurred at Codelco’s copper mine in Chile. Since then, Komatsu has put more than 130 haul trucks into seven sites on three continents to haul copper, iron ore and oil sands and its equipment has moved 1.8 Gt (2 billion st) of material with zero lost time incidents attributed to Komatsu’s autonomous trucks. The 1.8 Gt (2 billion st) is the most of any commercial mining autonomous haulage system and there is more to come. In November, Komatsu announced that an additional 150 autonomous haul trucks will be deployed to the Canadian oil sands over the next seven years.Komatsu has continued to pioneer autonomous haulage development, creating a range of autonomous options that includes semiautonomous and teleremote options all the way up to a haulage vehicle that stole the show at the world’s largest mining equipment trade show.In 2016, Komatsu advanced the concept of driverless haul truck to a new level when it displayed its Innovative Autonomous Haulage Vehicle (IAHV) at MINExpo in Las Vegas, NV. The concept vehicle is the first mega class haul truck designed to be fully autonomous, without an operators’ cab included on the vehicle.Unlike other haul trucks, the vehicle was developed exclusively as an unmanned vehicle designed to maximize the advantages of unmanned operation. Among other advancements, it was designed to distribute equal load to the four wheels, both when the vehicle is loaded and unloaded, and adopt four-wheel drive, retarder and steering. Komatsu said it is aiming for high-performance shuttling of this vehicle in both forward and reverse travel directions, thereby eliminating the need for K-turns at loading and unloading sites."

Dec 1, 2018

By Brett Schug, Caelen Anderson, Sohail Nazari, Carlos Cristoffanini

"The Haile gold mine in South Carolina is increasing the automation level of its processing plant in order to improve operational stability. One step toward this goal is the application of a digital twin concept to provide virtual instruments. Haile has engaged Andritz to implement virtual instruments at its grinding area hydrocyclones and at its tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The digital twin is a first-principles integrated design engineering with advanced simulation (IDEAS) simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters.OceanaGold’s Haile gold mine is located near Kershaw, SC, about 80 km (50 miles) southeast of Charlotte, NC. This location was first mined in 1827 and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile operation.The current operation began in 2017 as an openpit mine with additional underground resources. The nameplate throughput is 5,760 t/d (6,350 stpd) ore, and 2017 production was 3,345 kg (118,000 oz) gold, with 3,968 to 4,384 kg (140,000 to 155,000 oz) gold expected in 2018. Proven and probable reserves exceed 85 t (3 million oz) gold at a grade of 2 g/t (0.06 oz/st) gold. The process, as shown in Fig. 1, includes a primary jaw crusher, comminution with a semiautogonous grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon-inleach leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile operation’s inaugural gold pour took place Jan. 20, 2017. Mine life is expected through the year 2030."

Dec 1, 2018

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By Brenton Cook, Nate Long, Larry Applegate, Aaron K. McCain

"The Northgate Link Extension project is the third phase of the Sound Transit master plan to extend light rail throughout the greater Seattle metropolitan area. When completed, the Northgate Link Extension will extend the existing light rail system north by about 7 km (4.3 miles) from the University of Washington to the Northgate neighborhood. A general overview of the project alignment is provided as Fig. 1. The project was funded by a combination of federal grants and allocations from local taxes. The general contractor on the project was JCM Northlink LLC (JCM), a joint venture between Jay Dee Contractors, Frank Coluccio Construction Company and Michels Corp. SoilFreeze, Inc. was retained as a subcontractor to provide ground freezing design and construction services.The project involved the construction of two parallel 5.5-m, 25-cm (18-ft, 10-in.) (inside) diameter tunnels using earth pressure balance (EPB) tunnel boring machines (TBM) and precast segmental concrete tunnel liners. The two tunnels maintained roughly the same elevation along the alignment and were spaced roughly 12 m (40 ft) apart (centerline to centerline). A total of 23 cross-passages connecting the two tunnels were included at approximate 244-m (800-ft) intervals. Cross passage excavations were elliptical in shape with dimensions of approximately 5.6 m (18.5 ft) in height and 5.3 m (17 ft) in width. The cross-passages were 5.8 to 6.1 m (19 to 20 ft) long as measured between the exterior of the tunnels at springline elevation. Cross passages were intentionally located directly beneath public right-of-ways thus avoiding buildings. Many of the cross passages were located beneath narrow roads in residential neighborhoods with mature vegetation, existing utility structures and piping and limited parking areas. Excavation and support for each cross passage was completed using the sequential excavation method (SEM).The subsurface soil and ground water conditions at the cross-passage locations were described in the Northgate Link Geotechnical Baseline Report (GBR) prepared by Jacobs Associates and the Northgate Link Geotechnical Data Report (GDR) prepared by Shannon and Wilson, Inc. Soils along the project alignment were glacially overridden and characterized as very dense or hard. Subsurface soils consisted of cohesionless sand and gravel (CSG), cohesionless silt and fine sand (CSF), cohesive clay and silt (CCS) and till and till-like deposits (TLD)."

Dec 1, 2018

By John Dean

"Pumping backfilling medium used to fill in holes and caverns in mines is challenging. The often viscous, high solids materials are extremely abrasive and can destroy pumping systems in a matter of days. While a number of options are available, using a progressing cavity pump can often be the best solution. High pressure and capacity capabilities, coupled with low wear rates, ensures reliable cost effective operation.Thickened slurry backfilling for underground/excavation mining applicationsVoids and caverns develop as a result of mining operations penetrating deep into the earth seeking natural resources. After extracting all the ore from a mine, operators need to fill in these voids to preserve the integrity of the mine structure. They do this by pumping in a backfill medium. Each mine uses a different mix of components for backfilling, depending upon the mine’s specific structural requirements and environmental concerns, particularly water requirements. Most backfill mixes contain cement, or another cement-like substance, that acts as a binder to hold the backfill medium together. This is combined with tailings (unused rocks and waste from processing and/or extraction), and may also include chemicals or other binders to increase the material’s strength.Backfill pumping challengesPumping the backfilling medium can be a significant undertaking. This process involves transporting very viscous and high solid materials; the mix may contain 60-80 percent solids. These backfill slurries are extremely abrasive and the viscous material can wreak havoc with pumping systems. The material’s paste-like consistency presents problems for standard centrifugal pumps often used in other mining applications.Added complexity is posed when trying to achieve the required pressure, which depends upon how far away the material has to be pumped. It is not difficult to meet the pressure requirements if mixing the backfill material close to the area to be filled. However, pumping from extreme distances can be problematic — a great deal of pressure is required to transport the material from the mixing area to a distant backfilling site. Ideally, operators should be as close as possible to where they are filling, so they can use a smaller pump with lower power requirements."

Dec 1, 2018

By J. R. Heberger

"“Safety Pays in Mining” web application developed by the U.S. National Institute for Occupational Safety and Health Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of more than 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, the app will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items, such as services or equipment, on which companies could spend the savings that result from the prevention of injuries. This paper reviews the app by discussing its development, how it is used to show the true costs of mining injuries, and how mines can benefit from using it.IntroductionInjuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker or divert administrative resources in the wake of an injury. “Safety Pays in Mining” is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits.The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies do not usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, for example, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide that just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of the potential impact on their company’s financial health."

Dec 1, 2018