Search Documents

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By E. W. Geist, W. J. Bronkala

PRINCIPLES OF MAGNETIC SEPARATION The application of magnetic separators relies on the different behavior of individual mineral particles under the influence of magnetic forces. When exposed to a magnetic field, all materials are affected in some way. According to whether materials are attracted or repelled by the magnetic field, they are designated paramagnetic or diamagnetic, respectively. Paramagnetic materials are attracted along lines of magnetic force from points of lower magnetic field intensity to points of higher magnetic field intensity. The very strong response of some materials to a magnetic field is sometimes designated ferromagnetic and the particles attracted frequently retain magnetic properties after the applied magnetic field is removed. Diamagnetic materials are repelled along the lines of magnetic force from points of high magnetic intensity to points of lower field intensity. Only limited commercial use of diamagnetic effects has been made. For practical applications, the paramagnetic groupings are: 1. Strongly magnetic (ferromagnetic) 2. Magnetic 3. Weakly Magnetic 4. Non-magnetic The limits of these groupings are not well defined and will vary in some mineral species. Only a few minerals are ferromagnetic (magnetite is an example) and arbitrarily some investigators have selected 10,000 gauss, or 1 Telsa, as the dividing line between low and high intensity magnetic fields. I. S. Wells has developed a table indicating the magnetic intensity required to separate a selected grouping of minerals which is shown in Table 1 on page 2. A similar table has been developed by Carpco Inc. of Jacksonville, Florida in conjunction with the use of its high tension separators. This table, Table 2 on page 3 shows other minerals grouped in the broader categories cited above. Magnetic separation methods are used either to separate valuable minerals from nonmagnetic waste or magnetic impurities or other valuable magnetic minerals from bulk nonmagnetic values. Magnetically susceptible mineral particles occur as either individually discrete particles,

Jan 1, 1986

By A. W. Easton

INTRODUCTION This presentation will address changing trade patterns in lead and zinc from the mid 1980's to the early 1990's. Lead and zinc deposits are developed where they are found in many parts of the world. As many are not in major consuming areas, there is significant international trade in both lead and zinc concentrates and in refined metal. Forecasts of mine production have been analyzed, primary and secondary refining capacity and future consumption levels have been estimated, to arrive at the changes in trade patterns expected during the next half decade. This paper will first address concentrate and metal trade patterns for lead, then for zinc, and finally some remarks will be made on captive mine/smelter agreements, on regional trade agreements, and on barriers to trade. I would like to note that. there is only a small international trade in semi-fabricated products such as zinc die-cast alloy, zinc oxide, lead oxide or rolled lead and zinc. Most of the world's zinc and lead trade is in concentrates or refined metal. LEAD TRADE PATTERNS Lead Concentrates Six countries are exporters of lead concentrates. Three countries are in the Americas - Canada, Mexico and Peru, with two in Africa - Morocco and South Africa (including Namibia), and Australia. Due to the limited growth in lead consumption and consequent minimum investment in new production facilities expected, mine and metal production levels and future consumption levels are not forecast to change much between now and 1990. Accordingly, the tonnage of lead concentrates exported will remain essentially unchanged from these six countries. In total they have exports of 480,000 metric tonnes (metal content)* and by 1990 this figure is forecast to rise only slightly with the only increase taking place in Mexico. The concentrates are exported mainly to Western Europe & Japan. Apart from these six main lead concentrate exporting nations, a significant change is expected in the United States. In the mid * All concentrate trade figures are based on metal content

Jan 1, 1986

By L. Cui

A new flotation collector, benzyl arsonic acid, was used for the flotation of ilmenite. ESCA, Auger spectroscopy, and chemical analysis were used to investigate the correlation between the variation in surface constituents and the flotation recovery of ilmenite. Experiments indicated that, as the ratio of surface Ti ions/surface Fe ions increases, flotation recovery increases. pH regulation with an inorganic acid was found to be effective in changing the ratio of surface ions, and, hence, the flotation recovery.

Jan 1, 1986

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By J. D. Isbister

Coal is the most abundant and most economical source of energy in the United States, however, combustion of coal results in release of pollutants to the environment. The release of sulfur dioxide and oxides of nitrogen during combustion of coal contributes to the deterioration of the environment. Energy independence in the United States must include the increased use of coal reserves. Increased reliance on coal for energy will dictate the necessity for making coal a cleaner fuel. New technologies employing a variety of techniques from harsh chemical treatment to mild physical separations to clean coal are rapidly becoming available. Success for any coal cleaning process is in economics which translate into efficient removal of sulfur with high recovery of combustibles as well as low capital and operating costs for the process. Conventional coal cleaning processes remove water soluble sulfates and a portion of the pyritic sulfur and ash from coals. Removal of additional sulfur from coals requires more advanced coal cleaning techniques. Coal contains many organic sulfur forms which are the most difficult of the sulfur types to remove from coal. The heteroaromatic sulfur species, such as the comlex thiophenes, are the most commonly found organic sulfur forms. These sulfur forms are resistant to chemical attack and are considered to be refractory compounds. Atlantic Research Corporation has developed an "unique" microorganism, CB1 (Coal Bug 1), capable of oxidizing thiophenic sulfur in coal to form water soluble sulfates.

Jan 1, 1986

By P. R. Dugan

The ultimate objectives and interest in removal of sulfur from high sulfur coal include: (a) reduction of the atmospheric load that con- tributes to the problem of acid precipitation; (b) reduction of ash which contributes to decreased energy transfer in boilers and the problem of ash disposal; and (c) alleviating the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. The cost of sulfur removal in relation to the value of refined coal will govern the development of an emerging coal-refining industry. The value of refined lower sulfur coal will be influenced by the national commitment to the environment as well as economic considerations.

Jan 1, 1986

By Reed S. C. Rogers

The most widely used machines for grinding coal to the sizes prescribed for the pulverized coal firing of furnaces, boilers, and kilns are the vertical ball-race, roller-race and roller-bowl types of mills. However, the increased use of coal has led to an increased use of tumbling ball mills for coal grinding. Specifically, air-swept ball mills are now a part of many dry pulverized coal firing systems, offering the advantages over vertical mills of lower maintenance costs and the ability to handle strong or abrasive (high ash) coals. The current use of wet ball mills is to prepare coal-water slurries for direct combustion, although in time they may also find routine application for preparing slurry feed for coal gasifiers. In either application, wet ball mills ofer the advantages that coal grinding and wetting can be accomplished in a single step, and that the mills are readily used with fine wet screens to assure top size control in the slurry product. The simulation of tumbling ball mills with mathematical models has reached a fairly advanced stage, but the concepts have been applied only recently to coal grinding. As this paper will demonstrate, however, significant progress has been made in the use of models in ball mill circuit design for coal grinding. Included is a description of the techniques used for simulation, recommended parameter estimation methods, and demonstrations of process engineering calculations for large scale coal grinding circuits.

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Jan 1, 1986

By Huo Zuzhao

The main feature of caving methods is to draw ore from the overlying waste rock. Research on the movements of ore and waste plays a very important part in reducing ore loss and dilution and raising the economic benefits. This paper gives the basic theory of computer simulation of ore-draw, exposses the physical significance of mathematical model, puts forword a new formula of similarity characteristic value, brings forth a method of adjusting similarity, introduces the major functions of the simulation program and describes the ore draw control and stope parameter selection through computer simulation.

Jan 1, 1986

By M. Werner

Mining in the Coeur d'Alene Mining District has been going on for over 100 years with a long- term continuation very likely. Mining is presently carried out at depths below the -5000' horizon. As mining continues at ever increasing depths, higher in-situ rock stresses and subsequent rock deformation is encountered making mining costly and hazardous. To provide access for men and materials in such areas, a wooden raise preparation structure is typically built. Although these structures provide adequate support and access, they have proved to be very costly to construct and maintain.

Jan 1, 1986

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By Steve Kral

Competition from foreign coal producers could displace as much as 9 Mt/a (10 million stpy) of US coal bound for power plants located near waterways. But, according to a Maryland-based coal consultant, it could be worse. Theoretically, about 52 Mt (57 million st) of domestic coal could be vulnerable to imports by 1990, said Forrest Hill, of Hill & Associates of Annapolis. Hill was speaking to about 150 coal industry executives and experts at the third annual Coal Marketing Strategies Conference in November. Most were at the Denver, CO conference to pick up tips on how to sell coal in an oversupplied market. Imports threaten domestic markets Of the 200 utilities studied by Hill and his staff, 119 are situated near major waterways, he said. However, most of those waterways are not equipped to handle coal from the shipping lanes. Good news for US coal producers. But don't breathe too easily. Foreign coal still poses a major threat to domestic markets, Hill continued. The strength of the US dollar is an obvious factor. But easy access to US utilities located on waterways combined with low rates for ocean vessels give foreign producers another edge. And foreign mines are typically low cost producers. For example, Hill said Colombia's huge Cerrejon mine can deliver coal to an Illinois power plant for $47.87/t ($43.39 per st). That compares to $52.85/t ($47.95 per st) from a Kentucky coal mine. Also, Colombian coal producers can generate a cash flow even if the coal sells for $27.50/t ($25 per st). The main competition US producers face from abroad, as Hill sees it, comes from Australia, Canada, Colombia, Poland, South Africa, and, perhaps, from Venezuela. Domestic producers, however, do have some things going for them. Most US coal buyers, Hill said, "are not wild about the idea of buying foreign coal." A 10% price advantage or pressure from public utility commissions would be needed to force some of them to buy foreign coal, he said. Some of the utilities contacted said they would not commit to more than one-third of their stockpiles to a foreign source. Another advantage for US producers is that they have room in their long-term contracts to cut prices and still maintain a profit, Hill said. Railroads, too, have high profit margins written into their rate structures. They are also aware of the import threat. Therefore, they may reduce their rates accordingly to keep their markets. Marketing's role The energy price shocks of 1972 and 1976 caused major adjustments in world economics. Coal was no exception. High oil prices caused many utilities to look at less expensive coal. As the market improved, coal prices began to respond, said R. Gale Daniel, of Anaconda Minerals Co. But clean air legislation and the strengthening dollar caused havoc in the coal markets, he said. The price of oil crashed, taking with it predictions of record coal use. The result is an oversupply of coal that has led to price cutting. Now, coal marketing must be recognized in its "true leadership role," Daniel said. Marketing people must know when to use spot sales to balance production objectives and maintain cost-effective-

Jan 1, 1986

By Colin M. Kelly

The Loveridge Mine, located near Fairmont, West Virginia, has been mining coal from the Pittsburgh Seam since 1958. As the mine develops its reserves it finds itself with increasingly distant hauls from the operating faces to the preparation plant. Initially, the mine was designed with track haulage. The coal was hauled to an underground rotary dump which fed a slope belt, to the preparation plant. As the haulage distances increased, production delays due to the track system's limitations became severe. To resolve this situation, a complete review of the haulage system was undertaken. Simulations of the present system along with future scenarios were conducted to help management effectively plan the haulage requirements of the mine for the remainder of its life.

Jan 1, 1986

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920's. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950's. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By A. K. Ghose, S. Chakraborti

The research work outlined in this paper examines the utility of index tests for evaluating the strength of coal, both in the laboratory and in-situ. For routine evaluation of strength and deformation properties of coal seams, as inputs for design in stability analysis and equipment selection, the index tests are cost-effective and also make less demand on time and manpower. Four index tests, namely Protodyakonov Index, Cone Indenter Index, the Point Load Strength Index and Schmidt Rebound Hammer, were evaluated for 13 coal samples and correlated to fundamental strength and deformation properties such as uniaxial compressive strength, Brazilian tensile strength and modulus of elasticity of the same coal stratum. The index tests, barring Point Load Index, showed relatively low percentage scatter compared to the fundamental strength and show marked advantages for routine estimation of coal seam strength.

Jan 1, 1986

By Alejandro Prieto

Traditionally, Mexico has been a mining country. This industry has played a very important role in our country's development, creating jobs, integrating geographical regions - generally very remote from urban communities - and, an essential factor in our present day economy, generating an influx of foreign currency. The Fluorspar mining industry's development started in the 1920?s, but it was not until World War II that its exploitation became consistent and started growing. During the last few years, Mexico has become the world's leading producer, with an annual output of more than one million tons, which directly generates over 3,000 jobs. The actual proven reserves can guarantee fifty years of production at this same annual rate, and it is due to this fact that the producers have not increased their reserves. However, there is concrete information of the existence of several deposits, extending from the northern border to the gulf of Mexico, forming the "Fluorspar Belt? in Mexico.

Jan 1, 1986

By William F. Kane, Eric C. Drumm

Rock slope failures in the Great Smoky Mountains of Tennessee are a continuing problem. A study of the geotechnical factors affecting such slopes was conducted in this geologically complex region. Seven rock slopes, five of which had undergone failure, were identified and mapped. Other parameters were mapped in addition to the standard geologic and geometric parameters. These were joint frequencies across and down the slope, and surface hardness from Schmidt hammer tests. Regression analysis on the various data revealed that Schmidt hammer hardness correlates very well with joint cohesion back-calculated from failure geometries. This approach suggests an alternative means for estimating joint strength.

Jan 1, 1986

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By M. N. Brodie

The paper examines the requirements for electric power used in concentration and dewatering circuits, the effects of plant capacity and process type, the restraints imposed by the primary supply and applicable codes and outlines the procedure by which effective design is carried out.

Jan 1, 1986