Search Documents

By Seung-Chul Lee

Transparent conducting tin(1V) oxide thin films have been studies and developed for the electrode materials of solar cell substrate. Fabrication of tin oxide thin films by sol-gel method is process development of lower cost photovoltaic solar cell system. The research is focused on the establishment of process condition and development of precursor. The precursor solution was made of tin isopropoxide dissolved in isopropyl alcohol. The hydrolysis rate was controlled by addition of triethanolamine. Dip and spin coating technique were applied to coat tin oxide on borosilicate glass. The resistivity of the thin film was lower than 0.18-cm and the transmittance is higher than 90% in a visible range.

Jan 1, 1999

By R. Luo, R. V. Kumar

"The co-deposition of cobalt and nickel as a binary alloy has been studied by both cyclic voltammetry and long-period controlled-potential electrolysis. Cyclic voltammetry experiments showed that the cathodic current density for the mixed Co-Ni (Co-Ni=1:3) electrolyte is noticeably higher than that obtained on electrolyte containing single CO2+ or Ni2+ (II) salt of the same ionic strength. The onset potential observed for the mixed salts electrolyte was also less cathodic (negative) than that for the single metal salts, respectively. The effects of a number of operational and compositional parameters on the co-deposition of cobalt and nickel were studied. The parameters under investigation include cathode (deposition) potential, temperature, CI-/Sol ratio in the electrolyte, the amount of additives such as H3B03, and acidity of the electrolyte.Optimum operational conditions were established for the deposition of cobalt and nickel binary alloy. These results are discussed with respect to feasibility of reclaiming cobalt, nickel and chromium from mixed superalloy scraps by melt-refining (under nitrogen and/or ammonia), followed by electrorerining of cast anode for co-depositing Co/Ni and thermal decomposition of chromium nitride for recovering chromium metal."

Jan 1, 1997

By L. H. Lewis

The relationships that link microstructural properties of advanced permanent magnet materials with magnetic properties such as the coercivity are often difficult to quantify, especially in materials with nano-scale structures. Recent work on RE2Fe14B-based powders fabricated with rapid- solidification techniques such as inert gas atomization (IGA) and melt-spinning provide insight into the nanostructural features which affect the acquisition and stability of coercivity. In all cases the coercivity is found to be a function of both the scale of the constituent microstructure and of the presence and distribution of minor phases.

Jan 1, 1997

By Neil Rowlands

Particle liberation studies are commonly used in the determination of the proportion of locked and liberated phases in ground ores at various stages of mineral processing. These studies may range from a qualitative assessment of a polished specimen in an optical microscope to a full quantitative analysis of the liberation characteristics of fine grained complex sulfide ores using scanning electron microscopy and high level image analysis. However, the conversion of quantitative data to meaningful information on a mill operations level is by no means a simple task. This paper reviews the errors inherent in the SEM/Image Analysis technique and looks at the various methods available to minimize errors in data collection.

Jan 1, 1992

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction. The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory- scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the detennination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the detennined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors detennining the time of reduction.

Jan 1, 2003

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction, The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory-scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the determination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the determined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors determining the time of reduction.

Jan 1, 2003

By L. M. Luckevich

Gypsum is a product from the neutralization of sulfuric acid by lime or limestone. This paper will discuss specifications for gypsum used in wallboard, cement and agriculture and the factors affecting its utilization potential. Process conditions during the neutralization which enhance or inhibit utilization potential will be included. In addition, this paper provides a technical and economic perspective of the gypsum industry in North America with a view to the factors affecting the utilization of synthetic gypsum in traditional applications. Current production and consumption of natural and synthetic gypsum in Nonh America are described and the impact of their differences on utilization options are discussed.

Jan 1, 1996

By J. P. Constantinea

The use of fluidized beds for the roasting of zinc sulphide concentrates marked a milestone in the electrolytic production of zinc. Stable operation of a fluidized bed for zinc roasting requires a particle size distribution that minimizes the risk of defluidization and helps control carryover to manageable levels. However, the understanding of the roasting process is limited, and changes in operating conditions mainly rely on intuition, experience, and trial and error. A research program has been initiated at UBC to study the phenomena that influence the particle size distribution of fluidized bed zinc roasters. In preparation for the experimental phase, this paper reviews the current literature on the phenomena that affect the particle size distribution during fluidized bed roasting and other fluidized bed processes.

Jan 1, 2002

By Lionel Ryan

In 1996, the Dominican Republic operation of Falconbridge (Falcondo) developed a 5-year Process Control Plan in conjunction with the corporate Process Control group located in Sudbury, Ontario, Canada. This plan was further refined into an analysis of the areas of the highest potential economic return for the company with the reduction shaft furnace operation being the most promising. Historically, the reduction plant, which comprises 12 shaft furnaces, has been the bottleneck of ferronickel production. Since 1996 there has been a history of control development, and the current status is that all 12 furnaces are using advanced model-based multi- variable predictive control. The combination of advanced process control (APC), improved control system performance and improved process information management has resulted in an increased throughput of 6% per shaft furnace and a reduction in operating costs of 4.5 US cent/lb of Ni. This paper reviews some of the major milestones that have been achieved in this development Keywords: Advanced Process Control; Model Based Predictive Control; Connoisseur, Reduction Shatt Furnace; Nickel Laterite Ore; Ferronickel; MonitorMV

Jan 1, 2004

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

By H. Kandemir

An experimental study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fe1-xS, Cu5FeS4, ZnS) is presented using a mesophilic strain of T. ferrooxidans. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate has been monitored as a function of leach time. Partially oxidized sulphide substrates have been characterized, at regular time intervals, by X-ray diffraction methods and extracellular organic compounds reporting into leach solution .have been identified by thin layer -chromatography.

Jan 1, 1985

By Donato Firrao, Giorgio Scavino, Paolo Matteis

"The fatigue behavior of two high-strength sheet steels used to produce car bodies, a dual-phase steel and a TWIP one, both with ultimate tensile strength close to 1 GPa, is investigated.Unnotched tensile specimens are fatigue tested at room temperature with constant load amplitude and zero load ratio, in order to determine their 1 million cycles fatigue limit, both in the asfabricated sheet condition and after the resistance spot welding of one small homologous sheet square onto the calibrated length of the tensile specimen. Moreover, pre-cracked compact tension specimens are tested with load ratio 0.1 to determine the Paris fatigue crack growth curve.The fatigue results are completed with crystallographic, microstructural, tensile, and fractographic examinations, and the influence of the microstructure and of the welding processes is discussed.IntroductionCar bodies are increasingly made with high-strength weldable steels, in order to reduce vehicles' weight (to save fuel and reduce air pollution) and to improve the vehicle occupant safety in case of car crash. The main mechanical requirements of these steels in service are fracture strength and energy absorption, relevant for crashes, as well as fatigue endurance, relevant for ordinary car usage. [1]Steel sheets for car-body applications are usually made by continuous casting, hot rolling, cold rolling, continuous annealing (or other continuous heat treatment), and protective coating (in some cases). The sheets are then cold formed (deep drawn) to produce car body parts. Finally, the car bodies are built by assembling several deep-drawn parts, often consisting of different steels, usually through the Resistance Spot Welding (RSW) process, whereby two or three overlapping sheets are welded by local Joule-effect heating [2].Dual-Phase (DP) steels are widely used, low alloy steels with a microstructure consisting of ferrite and martensite, obtained from a final heat treatment which consists of heating at an intercritical temperature and then quenching. [3,4]"

Jan 1, 2012

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By S. N. Lekakh

Phosphorous segregated at grain boundaries during solidification and heat treatment dramatically decreases low temperature toughness of precipitation hardened Fe-Mn-Al-C austenitic steel. A thermodynamic analysis was performed to evaluate the possibility of decreasing P and subsequent segregation by Ca- and Ce-additives in the melt. It was shown that the predicted probability of forming a P containing compounds depends on melt composition and treatment sequence. Experimental heats were performed and several micro- and macro-structural effects of Ca- and Ce-additives were recognized by using an automated inclusion analysis technique.

Jan 1, 2010

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By Mark F. Vancas

Virtually every new process plant project goes through the ?Feasibility Study? phase before actually being built. The Feasibility Study is used by the owners and the bankers to evaluate the economics of the project and determine whether or not the proposed investment meets their respective investment guidelines. With a positive result, the project is approved and goes to construction and operation. Then, the actual costs are incurred and these actual costs may or may not agree with what the Feasibility Study predicted. Just how good have Feasibility Studies been? This paper looks at various projects and compares predicted to actual results and also gives information on how to spot a poor feasibility study.

Jan 1, 2003

By Oscar J. Restrepo

Through reactions in solid form at high temperatures, using iron oxide (Fe3O4) and chromium oxide (Cr2O3) in fixed proportions as precursors, the compound was synthesized with spinel structure type FeCr2O4. For different temperatures synthesis was conducted the characterization of the material obtained through X-ray diffraction (XRD), spectroscopy UV-VIS-NIR, scanning electron microscopy (SEM), energy dispersion analysis of X-ray (EDX) thermal analysis (DTA / TGA) and magnetic susceptibility of alternating current. The changes in the spectra of reflectance changes are related to the phase identified, the degree of crystalline structure, the spatial order of cations and the magnetic behavior obtained.

Jan 1, 2009

By Philip Nash, Jie Zhou, Joshua Blackketter

"Large ingots tend to have internal defects such as shrinkage cavities and porosities, which have to be closed during the cogging stage to ensure sound internal quality of forged parts. In this work, finite element methods were used to simulate open die forging passes, with varying parameters that affect the void closure behavior profoundly. Numerical models ware constructed in ABAQUS, DEFORM and FORGE using data taken from footage of the forging process and material mechanical data obtained from the Gleeble compression tests. Forging variables such as pass rotation, reduction per pass, and feed ratio were studied with intense attention paid on the special properties of H13 steel, so that this study can be applied to solve real world problem.IntroductionCenterline defect closure is a frequently studied but still challenging topic in open die forging industry. In practice, open die forging is employed as an effective hot forming process to make desired shape of metal products as well as to ensure center consolidation of internal defects which result from the casting process. Nowadays, remarkable large forgings have been more and more required to meet industries demand. However, the increase in ingot size has tended to result in considerable macrosegregations and shrinkage cavities or voids, which need to be worked thoroughly during the forging process; but the size of the products and limitations of manufacturing capacity, such as the press load, make it difficult to achieve adequate local deformation to close those defects. Therefore, choosing optimal forging parameters under given work condition to ensure good internal quality of forged products is critically important."

Jan 1, 2012