Search Documents

By Ju Shao-hua

Although nowadays gold extraction methods are very abundant, none of them is satisfying, especially, in the field of heap leaching of low grade gold ore. The traditional heap leaching method of cyanide method plays an inglorious role of badly environmental pollution. In this paper, a bran-new and innoxious method of gold extraction system, metal-ammonium-chloride-ammonia (MACA), was proposed, and also analyzed both thermodynamically and practically. Thermodynamically, according to the principles of simultaneous chemical equilibrium and electronic charge neutrality, the thermodynamics of Au-NH4Cl-NH3-H2O system was studied by using the exponential computation method and through MATLAB programming, and the solid figure of its potential - c(NH4Cl) - c(NH4OH) was drawn. The results showed when the concentrate of ammonia is higher than 0.6 mol?L-1, fAu+/Au is only about -0.2 v. Practically, the leaching results of a cuprous gold ore showed that the extraction of gold can reach to 80% in this system. The preliminary results of reduction of the rich solution with copper and zinc powders showed that with deoxygenizing, the reduction effects were relatively good. These new findings and results have established a theoretical and practical base for developing a new process for heap leaching of low grade gold ores in this system. And the new process owns a series of merits such as, non-cyanogens, nontoxic, broader applicability.

Jan 1, 2006

By Carvalho A. Felipe de

The search for environmentally friendly and cost-effective methods for gold extraction has been undertaken in order to provide alternatives to the use of cyanide leaching in the gold industry. Among such alternative reagents is the combination of chloride and hypochlorite ions due to their oxidation of metallic gold and its complexation. Therefore, the current work aims at investigating gold leaching from an oxidized material by means of a solution comprising calcium hypochlorite and sodium chlorite. The sample used in the current research contained 66.1% Fe2O3, 20.4%SiO2, and 35.7 g/t of Au. In addition, XRD and SEM-EDS analysis revealed iron oxide, quartz and muscovite as the main crystalline phases in the sample. For comparison purposes, cyanidation of the oxidized material resulted in 90% gold extraction in 24 h. The reference conditions for the leaching tests with the chlorite-hypochlorite system were: particle size −37 μm, solid/liquid ratio of 10% (w/v), 10 g/L NaCl, 10 g/L Ca (OCl)2, pH 5–6, 3 h of leaching. The effects of the: (i) Ca(OCl)2 concentration, (ii) NaCl concentration, (iii) pHrange and (iv) the effect of pulp density in the extraction of gold were assessed. In addition, the stability of the hypochlorite solutions (OCl−) was investigated. The ideal concentrations of Ca(OCl)2 and NaCl were determined as 25 g/L and 15 g/L, respectively, whereas the optimal pH range was 4–6. Under these conditions, the final gold extraction reached approximately 84%. By varying the solids content of the pulp (10%, 20% and 30%), it was observed that the lower solids value resulted in greater gold extraction (84%). The degradation of the hypochlorite solution and the possible catalytic effect of the presence of the solid were evidenced. To sumup, in the experiment, high gold extractions were achieved in shorter periods of time (3 h), as compared to the cyanidation of the same sample. On the other hand, itwas necessary to use significant amounts of the reagent due to hypochlorite instability at the pH conditions recommended for high gold extractions.

By Toyohisa Fujita

The effect of variables on the gold extraction with ammonium thiosulfate was investigated on sponge gold and ore samples. The Effects of CUS04, (NH4hS203, NH40H, (N~hS04' pH, stirring speed and retention on gold leaching rate and thiosulfate oxidation (consumption) have been studied. Almost 100% of gold was leached from sponge gold and over 96% from ore sample at optimum conditions. Trioctylmethyl ammonium chloride was used to recover gold from thiosulfate pregnant solution. It was found that more than 99% of gold was recovered by the extractant diluted with n-octane at 01 A ratio of 1: 1 without the re-adjustment of pH or others. Also, the gold cementation was conducted without de-aeration by using zinc, copper and aluminum powders. The result indicated that the gold was effectively recovered from a solution of low ammonia and copper concentrations and higher thiosulfate concentration. The gold recovery process by using ammonium thiosulfate is an environmental friendly method comparing to conventional cyanidation process.

Jan 1, 2003

By Bin Xu, Qian Li, Yong-bin Yang, Xiao-liang Liu, Tao Jiang, Yan Zhang

Some high sulfur and arsenic-bearing gold concentrate has a gold leaching rate less than 80% by oxidation roasting-pickling-cyanidation process. The characteristics and intensification of gold leaching were studied systemically. By combining chemical composition and phase analysis, the low gold leaching rate was found to lie in the capsulation of gold by iron-containing phases including iron oxides, arsenopyrite and pyrite. 96.66% of gold in the industrial leaching residue was capsulated and 95.88% of the capsulated turned out to be in the iron-containing phases. The results of laboratory pickling-cyanidation experiments on the calcine and industrial leaching residue presented further demonstration for the fact that gold capsulated in the iron-containing phases was hard to be leached. However, the gold cyanide leaching rate of calcine could be raised over 95% by a reduction roasting-pickling pretreatment which played such a significant role in exposing the capsulated gold that gold leaching was intensified remarkably.

Jan 1, 2015

By Chao Li, Shuai Wang, Hongxu Li, Lifeng Zhang, Xie Yang

The method of chloride-hypochlorite leaching has the advantages of short process, low pollution and higher in reaction rate compared with the traditional leaching method. In this research, NaCl - NaClO solution is used to leaching gold from a refractory gold concentrate, and the influence of NaCl and NaClO concentration, reaction time to the leaching rate were investigated in this experiment. The raw materials and the leaching residue were characterized by a series of analysis methods such as XRD, XRF, SEM and EDS. Results indicate that the leaching rate and the desulfurization rate can be achieved at 96.26% and 98% with most optimum conditions as follows: NaCl concentration 50g/L, NaClO concentration 200g/L, Liquid-solid ratio 10:1, the best reaction time was 150 mins. And these conditions should be guaranteed pH<8.0, ORP>900mV.

Jan 1, 2015

By Raymond E. Healy

Mercurian e1ectrum (Au-Ag-Hg alloy) is the principal Au-bearing phase in the massive sulphide ores at Trout Lake, Manitoba. The average composition of this phase (in wt %) is 49.2 % Ag. 38.7 % Au and 11.0 % Hg, with ranges of 17.34 to 76.47 % Ag, 1.62 to 79.86 % Au and 1.29 to 30.87 % Hg. Compositional variation reflects solid solution in the a-phase of the Ag-Au-Hg system. Backscatter electron imagery reveals systematic zoning and suggests a general crystallization sequence from metamorphic pore fluids of progressively Ag-rich compositions. Investigation of the occurrence of gold in mill products demonstrates that mercurian electrum accounts for over 90 % of the Au in Trout Lake ore. I Invisible" gold in pyrite (x = 0.72 ppm Au) and arsenopyrite (x 30.2 ppm Au) is confirmed by SIMS analyses, and accounts for 7-10 % of the Au in the ore, and 35 % of the Au lost to the tailings. The remaining 65 % of the Au lost to the tailings consists principally of mercurian electrum locked with pyrite. No significant losses of mercurian electrum in the size range amenable to flotation and/or regrinding is indicated.

Jan 1, 1989

By R. D. Osmanson

A series of batch roasting tests was performed on minus 1/2 inch gold bearing refractory samples from the Gold Acres deposit, and 67 select particles were polished and the sulfide alterations were examined microscopically. The suite of specimens represents two hour batch roast treatments at 600°C, 700°C, 725°C, 750°c, 800°C, and 900°C. Auriferous pyrites were found to alter sequencially to pyrrhotite, magnetite and finally to hematite. It was found that the decrease in cyanidation extraction with high temperature roasting is likely due to the increas ing stability of magnetite and more crystalline hematite, and the decrease in porosity with these phases which occlude the gold. Gold has been noted to occur very early in the mineralizing sequence, with gold being found in quartz and in clay/carbonate rock matrix. No gold was found in the two pyrite phases, but numerous gold grains were found in pyrrhotite after pyrite and in subsequent iron oxides. Gold mineralization had apparently ended by the time base metals were introduced into the deposit.

Jan 1, 1987

By M. M. Salari Rad

An investigation of gold distribution in the mill products of Sar Cheshmeh beneficiation plant demonstrates that on average 44% of the gold is routinely recovered as a by-product in the copper concentrate, and the remaining is lost to the tailing. In order to evaluate the causes of gold losses, the distribution and mode of gold occurrence in the Sar Cheshmeh ore and mill products were studied. Searching for gold within samples and within individual grains of sulphide minerals was carried out by SEM in the backscattered electron mode and SIMS, respectively. The mineralogical distribution of gold revealed by microbeam techniques were combined with the results of relevant metallurgical experiments including, sizing, heavy liquid separation, and diagnostic leaching tests, and the nature and location of gold in the ore and mill products were determined. The combined results of the experimental approaches pursued suggest that while there are some gold in solid solution and/or -colloidal size within sulphides of the Sar Cheshmeh ores, "visible" gold is the principal form of gold occurrence at Sar Cheshmeh.

Jan 1, 1999

By W. F. Drinkard

Many in the environmental movement have focused on this element. But, nothing they or anyone does will change the amount of arsenic in the world. This report is on actual commercial plants that we developed and operated to recover or stabilize arsenic values from metallurgical dusts from gold and copper pyro operations and arsenical gold bearing ores. When they were available gold and copper values were recovered. Our experience in arsenic extends over thirty years. My first corporation, Mineral Research & Development Corporation was the first in North America to manufacture the then new CCA (copper-chrome-arsenic) wood preservatives. This class of wood preservatives proved to be so effective that it made wood into an entirely new material of construction. It is not uncommon for wood properly treated with arsenical CCA preservatives to last for thirty; forty, and sixty years. Over a hundred years have been projected in some field tests. Hundreds of thousands of trees have been saved. Millions more trees would have been saved had environmentalists not decided that their arsenic phobia was more important than trees. There are several variations of CCA. The most popular is CCA-C. Its formula is: CrO3 . . . . . . . . . . . . . . . . . . . 47.5% CuO . . . . . . . . . . . . . . . . . . . 18.5% As2O5 . . . . . . . . . . . . . . . . . 34.0% Until recent restrictions were placed on the consumption of arsenical wood preservatives, annual consumption in North America was about 150,000,000 lbs./yr. About 64,500,000 of arsenic as the pentoxide was safely consumed this way. World CCA consumption has been about double the above figures or 300,000,000 lbs. as 100% CCA and 129,000,000 lbs/yr as As2O5. Close to 100% of all the arsenic used in wood preservatives is derived from gold or copper processing. The valence of arsenic required for CCA wood preservatives and many other markets is the same valence that is required for stabilization. The economic challenge is how to get there. We have built and operated eleven plants to oxidize arsenic trioxide to its pentavalent form. Most of these have been classic in that they used a common oxidants such as hydrogen peroxide or nitric acid to achieve this.

Jan 1, 2005

By C. Flores

A novel process using solid metals for the direct reduction of more noble metal ions from solvent extraction organics has been developed. Base metals recovery has been the principal focus of investigations to date but feasibility tests have now also been made on galvanically stripping selected precious metals. In this study gold (III) was loaded from an aqueous HAuCI4 .3H20 solution into a mixed organic 40 vol.% TBP, 10 vol. % D2EHPA in kerosene. The direct precipitation of metallic gold from the loaded organic phase using zinc powder and iron, aluminum and copper slabs at 70 °C was successfully demonstrated. The gold reduction rates were relatively fast even though the conductivity of the organic solutions is very low. The reaction rates were studied as a function of the variables zinc particulate size, oxygen and nitrogen atmosphere, water content in the organic phase, organic ratios and temperature. The gold morphology was usually powdery or dendritic in nature but continuous films were obtained in some instances. Activation energies were calculated and possible reaction mechanisms are discussed. In general, the results obtained were very promising and showed that gold can be successfully cemented from selected organic solvents by galvanic stripping using less noble solid metal reductants.

Jan 1, 1995

By R. Y. Wan

Low grade sulfidic-carbonaceous refractory ore from Newmont Gold Company&apos;s Carlin deposit was microbially pretreated. The biological pretreatment process gave partial oxidation of the sulfidic components of the refractory ore but the preg-robbing carbon continued to be active resulting in approximately zero cyanide gold extraction. A 495 ton pilot plant test heap was conducted using acidic thiourea leach following biooxidation. Activated carbon and cation exchange resin adsorption were tested for gold recovery from the thiourea pregnant solution. The results obtained from the test heap were not satisfactory. Gold extraction was low due to slow reaction kinetics which was caused by relatively large particles and very low winter temperatures. Problems existed in the thiourea-test heap and are discussed in this paper. An alternative heap leach process using thiosulfate has been successfUl at the pilot scale for gold extraction following biooxidation pretreatment of refractory sulfidic-carbonaceous ores.

Jan 1, 1995

By J. A. Brierley

A biooxidation-heap pretreatment process was field tested to evaluate enhancing gold recovery from a preg-robbing sulfidic carbonaceous ore. Newmont Gold Company&apos;s Gold Quarry sulfidic carbonaceous ore was inoculated with an iron-grown culture of Thiobacillus ferrooxidans to form a 495 ton test heap. Biooxidation was conducted for a period of 100 days. The most active period of biooxidation occurred during the first 40 days of pretreatment? About 35 to 40% of the sulfide was oxidized. The extent of biooxidation was considered good as the ore particle size was relatively large 58% >1?9 cm (&apos;/< inch). The larger particle size ore limited the extent of bacterial activity. The field test demonstrated the ability to conduct biooxidation in a small pilot test heap. Thiourea was evaluated for extraction of gold from the biooxidized preg-robbing ore.

Jan 1, 1995

By C. Dupuis

Thiourea is a promising reagent for gold extraction especially from refractory ores that cannot be treated by traditional cyanidation route. In this study recovery of gold from thiourea leaching solutions was investigated by direct electrowinning. The electrolysis cell consisted of a carbon flow-through cathode and a lead anode. The anodic and cathodic compartments were separated by a membrane. Galvanostatic mode was chosen for operation of the cell. Factors affecting recovery efficiency such as cathode thickness, linear flowrate, current intensity, thiourea and gold concentrations were investigated. The influence of some species in solution on efficiency and selectivity of recovery was investigated. Gold recovery reached 99% but current efficiency was lower than 10%. The complex formed with ferric ion and formamidine disulfide are reduced before gold-thiourea complex. Thiourea consumption occurred during leaching mainly by oxidation and reaction with dissolved copper.

Jan 1, 1989

By Jesús L. Valenzuela

The solvent extraction for gold from alkaline cyanide solutions has been investigated using LIX 79 guanidine-based extractant. Different variables that could affect the extraction system were evaluated: equilibrium time, aqueous pH and extractant and modifier concentrations. The extraction isotherms of the aurocyanide complex with respect to other cyanoanions were compared and the following order of selectivity Au>Ag>Cu>Zn>>Fe was observed. From the pH isotherms it was found that aurocyanide can be extracted in alkaline media and a better separation with respect to other cyanoaniones was obtained in the range of 10.5 < pH < 11.2. Better selectivity was observed when using LIX 79 and tridecanol at 10% and 5% vol, respectively. Stripping gold from loaded organic was carried out at pH>12, using NaOH and NaCN solutions.

Jan 1, 2003

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By Rajesh K. Mishra

The person in charge of Environmental Affairs in a small business has many higher priority projects (such as making money to meet the employee? payroll etc.) than filling out and filing the regulatory forms. It is but. natural to think that these affairs can be managed? by playing ignorant until audited by the regulatory -state and federal agencies. Truth is to. the contrary; generally, it is too late by then. The fines and legal costs even for failing to file the regulatory forms could deliver a serious blow to the financial well-being of a small business. Forms and reports under SARA Title III are not hard to complete., but they are time consuming. In this paper we will discuss the information and data compilation procedures, simplification of some legal terminology into simple technical language, and tips that help in filling out the forms?. Some actual case &apos;histories of EPA fines will also be reviewed.

Jan 1, 1992

By T. Xin

A vertical grain boundary intercepting a horizontal free surface forms a groove to reduce the combined surface energy of the system. We study grooving by surface diffusion with anisotropic surface energy. A recently developed delta-function model of facets is used to describe the surface energy with three or four fold symmetry. It is found that the groove grows following a similarity law. The self-similar groove profile is solved numerically by a shooting method. Even with strong anisotropy, the groove profile can be smooth if the exposed surface orientations do not include a facet orientation. The smooth self-similar groove shape is the same as an isotropic groove, but the size is reduced by a factor that depends on the degree of anisotropy. This induces a large error on the value of surface diffusivity if the isotropic model is used for an anisotropic system. In this talk. we will describe how to correct for this error.1 I Xin, T. and H. Wong, "Grain-Boundary Grooving by Surface Diffusion with Strong Surface Energy Anisotropy," Acta Materialia 51, 2305-2317 (2003). Keynotes: Grain growth, Surface Diffusion, Surface energy, Anisotropy

Jan 1, 2003

By M. Sadayappan

The grain refinement characteristics of four low-lead and lead-free copper base alloys for plumbing applications were investigated. These are leaded yellow brass (C85800). SeBiLOY III (C89550), silicon brasses (C87500 & C87800) and silicon bronzes (C87600 & C87610); Boron and zirconium were found to be the most effective .grain refiners for copper .alloys produced using the permanent mold cast processes. The study indicates that the type of grain refiner to be used is dependent on the alloy type, alloying constituents and their content. After grain refinement, hot tearing resistance of the alloys was improved but mechanical properties remained unaffected. Alloys refined with boron are prone to the formation of hard spots, which will have adverse effect on the surface quality of the castings during polishing and buffing.

Jan 1, 1999

By Hiroshi Nakajima, Kotobu Nagai, Toshihiro Hanamura

"Low carbon ferritic steel bars with ultra-fine grain structure was developed through a warm rolling for the first time by the present authors. They show better low temperature toughness than conventionally hot-rolled plates. Hence, the brittle fracture surfaces in Charpy tests were examined in terms of the effective grain size of fracture, compared with those of conventional QT steels. The ductile-to-brittle transition temperatures were in good accordance with those for the QT steels if referred to the effective grain size of fracture: · However, the size was a few times that of the ferrite grain. This means the grain refining is not yet fully utilized from the viewpoint of low temperature toughness. The anisotropy of· the impact properties and the annealing effect of highly dislocated structure on the toughness are also discussed in the present paper.IntroductionFor structural materials, both high strength and good toughness are required. Well-known approaches for obtaining better toughness for steels are as follows:1) Grain refining2) Addition of Ni3) Thin plate effect by cracking parallel to the rolling direction prior to crack propagation4) Contribution of metastable austenite.Among them, only the grain refining can raise the strength and improve the toughness. And it is well known that the finer the ferrite grain size, the lower the ductile-to-brittle transition temperature. For example, in the case of 0.11 carbon steel, the transition temperature decreases linearly to in d 1/2 [1 ]. However, these have been told in the regime of coarse grain size that is larger than 10 µm in diameter. There ~as .been no study dealing with the low temperature toughness in the regime of ultra-fine grain size with a diameter in the order of 1 µm."

Jan 1, 2000

By R. A. Masumura, C. S. Pande, D. Agassi

"Grain size has a different effects on the critical current density (Jc) of high and low transition temperature (Tc) superconductors. In high Tc superconductors, the critical current density Jc across grain boundaries depends sensitively on the misorientation 8. It was pointed out by Pande that this dependence is directly related to dislocation structure of the grain boundaries i.e., it is due to dislocation cores and stresses. These ideas are developed further in this paper leading to a relation between Jc and 8. The analytical result is compared with the experimental results on bicrystals and used to explain the difference in behavior between high and low Tc superconductors.IntroductionThe grain size distribution and its evolution with time and temperature is important in determining the properties of high and low transition temperature (T c) superconductors. The distribution is a convenient function to characterize the processing of a high Tc material during sintering. For example, it is known that the maximum density of ceramic materials is obtained when the grain growth is reduced but grain boundaries are still mobile. For practical superconductors, the processing parameters are selected to achieve optimum properties: highest possible T c and maximum critical current (Jc). In terms of an average grain size, the requirements for optimum T c and Jc are sometime in conflict. In A15 type superconductors and even in NbTi, larger Jc have been measured in smaller rather than larger grain sized material. Conversely, in a high Tc materials like YBa2Cu307, higher Jc have been found in larger grain sized or single crystal specimens.Extended defects such as grain boundaries in low T c superconductors can be effective pinning agents for magnetic flux lines, thereby increasing the transport critical current density of these materials [1]. On the other hand, the transport critical currents in polycrystals of high Tc superconductors such as YBa2Cu307 is found to be relatively small (much smaller than those in single crystals of the same material) [2]. It is now known that grain boundaries in high Tc polycrystals can in many cases form ""weak links"" reducing the critical current density across them. This phenomenon can be studied more precisely by experiments on bicrystals, where there is only one grain boundary. It is found that the critical current density is quite sensitive to the misorientation angle of the bicrystal [3,4]. Although the original experiments were conducted on YBa2Cu307, other Tc superconductors have been shown to give the same result [5]."

Jan 1, 1994