Search Documents

By R. Abel F.

In 1997, Ventanas electrolytic refinery expanded its production capacity from 215,000 to 325,000 metric tons per year. This increase in capacity has involved the treatment of anodes with different impurity contents, changing the operational strategy of the plant. On the other hand, the increasing necessity to accomplish environment conservation rules and quality assuring requirements, has led the plant operation and administration to compete in an advantageous way. The present work describes the results obtained in the startup and in the operation of the ENAMI Ventanas electrolytic refinery expansion, and shows the difficulties which have been faced in the processing of anodes of increasing complexity, in a competitive market and with environment and quality restrictions.

Jan 1, 1999

By Shuichiro Okada

Various efforts to reduce energy consumption and smelting cost are made at Tamano Smelter. Production of anode copper has been increased by about 30 % and energy requirement has been decreased about 50 % respectively. Challenges toward more higher goal are being continued. Details about the following are described in this paper. 1 Waste heat recovery Steam recovery at up-take of FSFE Heat recovery from waste gas of anode furnaces 2 Application of tonnage oxygen 3 Application of pulverized carbonaceous fuels to the flash smelting furnace with furnace electrodes ( FSFE ) 4 Application of computer control system to copper smelting 5 Improvement of the fugitive gas collecting system 6 Improvement of the mechanical tuyere puncher for the converter furnace

Jan 1, 1983

By K. Moriyamo

Operation improvement efforts at Hyuga Smelting Co., Ltd. have focused on calcining capacity in the reduction rotary kilns ("the kilns"), whose limited feed rate capacity had capped production at around 18,000t-NiN since 1995. To improve the kilns' feed rate capacity of 80 wet t/hr, attempts were made to increase the gas flow in the kilns by increasing the capacity of the off-gas fans. However, as the increased gas flow resulted in only limited improvement of the kilns' feed rate, a scoop feeder was installed on each kiln to add coal to the middle of each kiln's interior to gain a higher efficiency of thermal supply and conversion. With these gas flow and coal charge addition operations, the kilns' feed rate capacity increased up to 120 wet t/hr, with burner fuel efficiency increasing by approx. 10% (approx. 5% in total with the additional coal included). As a result, production was raised to a level of 22.000t-Ni/Y Keywords: reduction rotary kiln, scoop feeder, additional coal charge.

Jan 1, 2004

By Kenji Sasaki

Tamano Smelter started its operation in January, 1972 adopting FSFE ( Flash Smelting Furnace with Furnace Electrodes ) type smelting furnace at a production capacity of 101,00Ot/y of anode copper and 285,00Ot/y of sulfuric acid. Since then, it had experienced several production expansion program, it had twice as production capacity as start. 196,000t/y of anode copper and 436.000t/y of sulfuric acid. This time, we have completed the plan for increasing production capacity up to 226,000t/y of anode copper and 510,000t/y of sulfuric acid, by the oxygen enriched operation. We carried out several improvements and modifications, changing of cooling system ill FSFE, enlargement of converter and anode furnace, and some progresses in sulfuric acid plant and environmental facilities.

Jan 1, 1993

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By Pietro Navarra

A great deal of effort has been expended on how to optimize conventional water cooling circuits in furnace cooling elements, and the results have been largely satisfactory. However, there is a general agreement that the proximity of high-pressure water passages to the flow of molten furnace products is a safety concern. Nonetheless there exists little alternative to the formula: increasing furnace integrity implies the incorporation of more extensive forced-convection water cooling systems. Recent developments in evaporative cooling technology have resulted in the development of a high-capacity heat pipe capable of operating under the thermally intense environments of a metallurgical furnace. The system functions using several kg of a working fluid (water) in total, has no moving parts, and allows for a significant reduction in cooling water requirements. Full-scale pilot tests of a copper tap hole and slag launder were done in 2003 and2005, with detailed results given in this paper.

Jan 1, 2006

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989

By F. Sakurai

The enlarged Mitsubishi process in Naoshima has been in steady operation since. May 1991. However, the sulfuric acid plants have been in operation for more than 30 years. The acid plants were modernized between 1999 and 2001 by renewing some of main equipment such as the drying tower and gas heat exchangers, and introducing new technology. At the same time, as an electric energy saving measure, the electric power consumption in the sulfuric acid plant was vastly improved by decreasing the volume of gas treated the installation of low temperature activity catalyst in the 1st pass of the converter and optimization of main gas blower runner. Furthermore, last year, the oxygen plant was replaced and enlarged, and anode production increased from 240,000 to 280,000 tonnes per year with an associated increase of sulfuric acid from 550,000 to 660,000 tonnes per year. This paper describes these recent improvements in the acid plant at Naoshima smelter.

Jan 1, 2002

By E. O. Stensholt

The Hybinette electrorefining process for production of cathode nickel was in use at Falconbridge Nikkelverk A/S, Norway, until 1975 when conversion to the new chlorine leach process was started. In 1978 the conversion to electrowinning had been completed, but further major improvements to the process have been made up to 1987. After a major expansion program in 1985 - 87 the refinery has a nickel capacity of 54 000 mt Ni/year. The main feed materials to the process are converter matte from the Falconbridge smelter in Sudbury, Ontario, Canada, and from the BCL smelter in Selebi-Phikwe, Botswana. A typical composition of the mixed feed to the refinery is: 40 - 45% Ni, 25 - 30% Cu, 20 - 22% S, 2 - 3% Fe and 1.0 - 1.5% Co. The matte is chlorine-leached in the first process step, nickel being dissolved selectively in a train of leach-cementation tanks. Essentially all copper and sulphur that was present in matte appears in the leach residue as CuS. In 1986 an autoclave treatment stage was added to the process to improve nickel extraction from the leach residue. The resulting strong nickel chloride solution is purified by the process steps (1) precipitation of iron and arsenic, (2) solvent extraction of cobalt and other minor elements and (3) precipitation of lead and the remaining impurities. The nickel solution is then fed to the tankhouse, where various nickel products are produced by electrowinning. The chlorine gas that is produced during the electrolysis is returned directly to the chlorine leaching tanks to dissolve more matte. After stripping from the loaded organic phase and solution purification cobalt is also produced by electrowinning. The copper sulphide leach residue, which contains some nickel, is dead- roasted in fluidized-bed roasters. The sulphur is recovered and sold as sulphuric acid. The calcine is leached in spent copper electrolyte, from which cathode copper is produced by electrowinning. Precious metals and the remaining base metals are recovered from the copper leach residue. The Falconbridge chlorine process is very versatile. It can accept a wide range of impurities in the feed and still produce metals of exceptional purity.

Jan 1, 1988

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000

By Marcelo Jimenez Bustos

The Chagres Smelter was the first in Chile to follow environmental regulations to control sulfur dioxide emissions. Because of this, the operation and development plans have had to incorporate environmental planning as part of its policies for almost three decades. The present article shows the development of the environmental standards applied to its operations, investments and operational improvements carried out to meet the regulations and improve competitiveness. Results to-date and future plans are outlined, as well as their impact on operations and the environment.

Jan 1, 1993

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would be reduced at the new smelter to about a half of the sum of those from previous two 1 smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive offgases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would, be reduced at the new smelter to about a half of the sum of those from previous two smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive off gases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By C. J. Newman

The new Kennecott Utah Copper smelter, started in 1995, was designed to be the cleanest smelter environmentally in the world. The plant is operating at production rates above the original design capacity. Copper concentrate is smelted in an Outokumpu flash smelting furnace. Matte is granulated and processed using Kennecott-Outokumpu flash converting. Copper anodes are processed in a modernized copper refinery using the Kidd Process while anode slimes are processed for precious metals recovery using a unique hydro-metallurgical process. To allow the production of high quality cathode, using modem smelting and converting technology to minimize emissions, impurity control had to be carefully addressed. All process bleed streams from the smelter and refinery are treated in a hydro-metallurgical plant to fix impurities in a stable form, allow for the rejection of impurities as required and recover valuable metals. Special technology was developed for the copper refinery to ensure production of high quality cathode from anodes containing high levels of impurities. The smelter routinely achieves a sulfur capture in excess of 99.9% which is equal to less than 2 kg of SO2 per tonne of copper produced. This paper describes the design of the smelter and refinery and includes recent production and emission data and modifications carried out to allow operation at above the original design rates. It emphasizes the unique features required to achieve environmental and quality goals and compares environmental performance data to that published on other smelting operations. The processing of intermediate streams, the management of recycled materials and the impurity control strategy will be covered in detail.

Jan 1, 1999

By Kosei Morita, Osamu Nakano, Katsuhiko Nagai, Kazuhiro Mori

"The Sumitomo Toyo Smelter and Refinery commenced its operation in 1971 with three Peirce- Smith (PS) converters. “2 hot – 1 blowing” operation was practiced, that is one of two available converters was blowing and the other was standby in a hot state while the third converter was under repair. After several improvements, the stack time ratio reached around 90%; and processing 5 batches a day became possible.As a result of the expansion program of the Toyo smelter and refinery that started in 2001, the converter operation pattern was shifted from “2 hot – 1 blowing” to “2 hot – 2 blowing” with the installation of second converter blowers and an additional ladle crane.In 2005 a, the fourth converter was installed and “3 hot – 2 blowing” operation began. Also, with improvements experienced in the anode furnaces and the anode-casting wheel operation, today, the number of cycles has been increased up to more than 8.5 a day.The treatment techniques of fugitive gas containing sulfur dioxide from converter furnaces have been gradually reinforced, and the fixation rate of treated sulfur is currently being maintained at more than 99.9%. This paper introduces the operations described above, and the improvements in environmental management techniques for the Toyo PS converter operation."

Jan 1, 2009

By E. Oshima

The only one reverberatory furnace smelting in Japan has been alive in Onahama Smelter, Onahama Smelting and Refining Company. The fuel for the reverberatory furnaces had been changed from bunker C-oil to mainly coal and partially waste tires to reduce the energy cost. The steam, recovered by the waste heat boilers of the reverberatory furnaces, has been utilized fully for the power generation to save the purchase power. Copper concentrate has been smelted also by injection through tuyeres in the P.S. converters since 1983. The amount of concentrate, treated in the converters, was increased by the construction of small oxygen plant in December, 1990. In the paper, the current practice and improvements in the reverberatory and converter operations are described.

Jan 1, 1993

By T. Shibaraki

A new larger, more efficient and economical Mitsubishi furnace line at Naoshima was put into operation in May 1991. Naoshima Smelter had produced previously about 230,000 mtpy anode copper with two smelter lines, i.e., a conventional reverberatory furnace line and Mitsubishi furnace line, which had been shutdown at the same time of the start up of the new smelter. At the beginning of the operation, there were several initial problems at the area of off gas trains and feeding system. By overcoming them now the process has been continuing satisfactory operation at the design rate. The paper describes about the design concepts and the actual operation of the new smelter.

Jan 1, 1993

By E. Oshilna

The Mitsubishi process has many advantages pertaining to economical and environmental matters. These advantages have led to the installations of the Mitsubishi process in constructing new smelters: The Mitsubishi process utilizes highly oxygen enriched blast air and uses a special lime slag in the C?furnace. These characteristics change the . distribution of Impurities from other processes which use P.S. converters, Recently an Increased amount of secondary materials which contain impurities Is being treated at Naoshima Smelter. In order to cope with an Increment of the Impurities load and maintain the cathode quality, many Improvements have been Implemented. This paper discusses the impurities behavior In the Mitsubishi process and describes the measures taken to treat an Increased ?amount of secondary materials:

Jan 1, 1998

By Yoshimasa Oda

The tank house of Tamano Smelter has adopted a high current density electrolysis operation applying PRC (Periodic Reverse Current) method and before 1991, it had materialized both high production capacity of 161,000 tons/year and high labor productivity. However, recent rapid rise of Japanese currency in foreign exchange market has urged us to further exert our efforts in reduction of labor cost. In order to achieve this goal of labor cost reduction, we have completed, in 1994, our phase four production expansion project which incorporated significant re-structuring of the organization and we have accomplished annual production of 191,000 tons/year. This project can be outlined as increase of number of cells for electrode exchange per day in the commercial electrolysis process to meet the increased number of cells and increase of the capacity of impurity treatment process. These improvements were done with minimum installation of new equipment and facilities and with achievements in efficiency and manpower saving of the existing facilities. Together with these improvements, rationalization in the starting sheet section was carried out by changing the material of mother blanks as well as changing their maintenance procedures. At the same time, the crane in this section was modified to enable automatic operation by a fuzzy control. As a result, we were able to save manpower equivalent to 5 operators in this section. With these improvements, the production capacity was increased by 18% and labor productivity by 25%.

Jan 1, 1996

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000