Search Documents

By Peter Forschner

Classical Mixing Theory is based on applying many fundamental correlations to standard baffled dished bottomed vertical cylindrical vessels with high degrees of symmetry. Horizontal autoclaves operating at elevated temperatures and pressures have been used for more than two decades. All compartments and especially the first and last compartments are asymmetrical. To date no comparison of the effects of the asymmetric geometry on mixing system design and scale-up has been published. The results of investigating solids suspension, mixing time, momentum transfer from the impeller to feed slurry and feed inlet location in the first autoclave compartment are presented as influences on residence time distribution. CFD modeling was developed and verified with the test apparatus.

Jan 1, 2003

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By Tatsuzo Kitamura

The tank house of Tamano refinery, that started its operation in January, 1972, was constructed incorporating the application of Periodic Reverse Current (P.R.C.) from the outset of design works. In 1973, the production of electrolytic copper came up to 8,000 mtpm, a sharp increase ds compared with the designed capacity of 7,000 mtpm, and successful operation has been achieved up to the present. P.R.C. has been employed for the purpose of raising productivity level and reducing copper inventories. Since there were various problems in P.R.C. application to such a large sized cathode as 1 m x 1 m, special attentions were paid to the following items: -Development of a unique bus bar to make an electrolytic current to each electrode as uniform as possible. -Improvement of circulating method of electrolyte. -Application of high-performance equipment to realize a uniform spacing between anode and cathode. Owing to these creative technical developments mentioned above, technical level for operation up to 350 amp per sq m of cathode current density has been established. The quality of electrolytic copper, which was a matter of interest, has been proved to be as excellent as those of conventional electrolysis products through a long term supply to the field of SCR and Dip forming where high levels in quality are required.

Jan 1, 1976

By J. Garvey

The new Cyprus Miami electrolytic copper refinery was commissioned in October 1994. The refinery has been operating at its design capacity of 190,000 short tons per year, and in recent months to 110% of design capacity, producing high-grade electrolytic copper cathodes. Basic and detailed engineering, performed by Fluor Daniel Mining and Minerals, incorporated state-of-the-art technology, including stainless steel cathodes, automated electrode handling, fine-filtering of the commercial electrolyte, autoclave leaching of the anode slimes and other techniques. The major design goals have been safety of operation and quality of the product. Relatively high cathode current densities of 30 amperes per square foot and greater have been applied since start-up. Cathode current efficiencies of over 94% have been achieved since the latter part of 1997. The cathodes were certified on the Comex and LME markets during 1996. ISO- 9002 certification is in progress and should be completed during the first quarter of next year. This report discusses some of the studies that were performed to obtain an optimum layout for efficient materials handling and to create optimum conditions for producing high quality cathodes. A description of the design and operation of the anode slimes facility, including decopperizing with autoclave leaching, is provided. Finally, a description of the start-up experiences and present operation of the electrorefinery are presented.

Jan 1, 1999

By F. Baldini, M. S. Borges

"The proposed method emphasizes the optimization of waste management with regard to the exploitation of raw materials incorporated in the remains of industry, as well as the economics of natural resources as an environmental impact assessment. This system [tool] allows: (a) the conversion of an environmental liability into an asset by finding a line of appropriate research for each type of waste and the development of new materials applicable to other industries, (b) the performance of internal control of the waste generated (production, storage, final destination) as well as legal conformity.Objectives:1.1 General objective:To design a collaborative system for socio-environmental management of industrial waste.1.2 Specific objective:Develop evidence of concepts;Evaluate the deployment of the inventory of waste in an industry;Enable the conversion of an environmental liability into an asset by finding a line of research appropriate to the waste: a case study;Evaluate the environmental legislation in the legal mechanisms that influence company decisions.IntroductionThe global economy is undergoing major changes, among these changes; it should be highlighted those related to technological progress and environmental quality.While the industrialized countries and higher levels of economic growth dominate modem technology, developing countries are identified by a different growth pattern, using the annual growth rate of Gross Domestic Product per capita [3, 18].Growth is when the GDP grows, in percent, over the previous year. Development, on the other hand, is when the countries change their technologies and improve their internal structure. Thus, the growth considers the accumulation of wealth, while the development is concerned with the distribution of wealth, improvement of the quality oflife and environmental quality [3, 18].As the UNESCO report shows (1999), the biggest problem is between consumption and development, what is produced and the end that is given to the product. Therefore, product and by-product have equal importance in the quantity produced [29].On one hand there is a positive relationship between indicators of economic growth and technological progress, however, on the other hand, these transformations are a paradox, confirmed by the dramatic use of environmental resources and the lack of technologies for recycling of industrial scrap."

Jan 1, 2011

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By Andy Judge

"In traditional Permanent Magnet Machines, such as electric motors and generators, power is transmitted by magnetic flux passing through an air gap, which has a very low magnetic permeability, limiting performance. However, reducing the air gap through traditional means carries risks in manufacturing, with tight tolerances and associated costs, and reliability, with thermal and dynamic effects requiring adequate clearance. Using a magnetically permeable, high thermal conductivity material has the potential to improve magnetic performance, while at the same time offering performance advantages in heat transfer.Ferrofluids can be used to improve permeability in the rotor I stator gap. However, there are several tradeoffs in this approach. Fluid immersion comes with an increase in fluid friction loss compared to the windage losses of a traditional system. Isolating the rotating components from the ferrofluid can offset this effect. Also, while the magnetic effect can be positive for gap permeability, leakage flux can increase, and saturation can limit gains. These effects must be taken into account for a system optimized for ferrofluid immersion.IntroductionPermanent Magnet Machines (PMM's) convert electrical energy to mechanical energy in motor applications, or, for generator applications, convert mechanical energy to electrical energy through means of passing alternately polarized magnets past electrical coils. Looking at a simplified version of a PMM, where Rx is magnetic reluctance and <l>x is magnetic flux, we have the circuit shown in Figure 1."

Jan 1, 2013

By A. F. Kaczmarek

Cerro Negro is an undeveloped ore body located at the Cerro Verde mine near Arequipa, Peru. The mineable reserve contains 70 Mt of oxide ore grading 0.532% copper. Mineralization is hosted in three distinct rock types: tourmaline breccia, crackle breccia and granodiorite. Rock type effects copper recovery and acid consumption. The paper describes Cyprus&apos; testwork philosophy and the resulting four-phase metallurgical program used to define the commercial leaching parameters. Copper recovery and acid consumption were monitored as functions of crush size, heap height, irrigation rate and acidulation conditions. Single lift, on-off and permanent multi-lift heaps were considered. Leach cycle times were based on incremental copper extraction and acid consumption rates, with added constraints imposed by operational requirements. The optimum leach system involves an on-off pad using tertiary crushed ore acidulated with 20 kg/t acid and stacked to a height of 6.5 m. The active leach cycle is 82 days at an irrigation rate of 0.26 l/min/m2. Under these conditions copper recovery is expected to average 81% over the life of the mine.

Jan 1, 1999

By D. J. Senor

Closed chamber incineration (CCI) is a novel technique by which irradiated nuclear graphite may be destroyed without the risk of radioactive cation release into the environment. The process utilizes an enclosed combustion chamber coupled with molten carbonate fuel cells (MCFCs). The transport of cations is intrinsically suppressed by the MCFCs, such that only the combustion gases are conducted through for release to the environment. An example CCI design was developed which had as its goal the destruction of graphite fuel elements from the Fort St. Vrain reactor (FSVR). By employing CCI, the volume of high level waste from the FSVR will be reduced by approximately 87 percent. Additionally, the incineration process will convert the Sic coating on the FSVR fuel particles to SiO2, thus creating a form potentially suitable for direct incorporation in a vitrification process stream. The design is compact, efficient, and makes use of currently available technology.

Jan 1, 1994

By Richard A. Heckman

Destructive Thermal Technology (DTT) is used in the management of various waste streams. DTT includes Destructive Distillation, Pyrolysis and Classical Incineration. Recent work has more clearly defined the differences in these technologies based upon a more rigorous thermochemical approach. The U.S. Environmental Protection Agency (EPA) has chosen Classical Incineration as the Best Developed Available Technology (BDAT) for the management of hazardous organic wastes. Municipal Solid Wastes (MSW) and Sewage Sludges (SS) are also managed using Classical Incineration. Three environmental problems plague the use of Classical Incineration. Destructive Distillation, on the other hand, avoids these problems. It is an environmentally benign DTT for managing a wide variety of organic waste streams, including hazardous wastes. Thermochemical analysis of the available data on the performance of three types of DTT will be discussed.

Jan 1, 1994

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By Ahmet Geveci

[Generally accepted formula related to sulfur slag-metal distribution ratio is given by the following equation: [ ] According to the above equation it can be deduced that sulfur distribution between slag and metal is governed mainly by metal composition (?s term), slag composition (slag basicity and in turn sulfide capacity), oxygen potential of the system (ao¬¬ term) and temperature(related to equilibrium constant, K). In this study, the results of ladle furnace operations conducted in Erdemir-Iron and Steel Works Co. (Turkey) in relation to sulfur removal, have been given. Typical ladle furnace slag analyses of 4937K quality steel have been presented. Activity coefficient of FetO,?FetO, have been calculated with the relation obtained fromthe literature. Activity calculations have been performed with the program written in Mathcad. The changes in activity of aFetO in the slag phase,, have also been studied in relation to the sulfur removal: The relation between % Decrease aFetO and %DeS (measured)have been investigated for 4937K runs and someother types of steel produced in the Erdemir Plant. Related to ladle operations %desulfurization defined as [(%Sinitial-%Sfinal)/S%initial]*100 values have been presented for different steel qualities.]

Jan 1, 2006

By Ho-Sang Sohn

The kinetic study on desulfurization of copper matte by gas bubbling was designed under the presumptions of lower FeO activity and of no slag formation, Copper matte with 59% Cu and 22.6% S in weight was oxidized at 1523K by bubbling of Ar + O2 gas through a submerged nozzle. The effects of oxygen partial pressure and flow rate of gas on the oxidation rate of matte were discussed. The desulfurization rate and the evolution rate of SO2 gas of copper matte were significantly influenced by the oxygen partial pressure, but the dependence on gas flow rate was rather complicated. The desulfurization rate and evolution rate of SO2 gas of copper matte were described by the mass transfer rate through the gas film around the rising gas bubbles. Thermodynamic correlation equations between the partial pressure of gaseous species and matte composition were incorporated to the kinetic calculation, The present model shows that the reaction path starts to transiently cross over an isobar line of PSO2 to asymptotically approach to the particular isobar line drawn in a matte composition plane of %S and %O.

Jan 1, 2003

By M. H. Erten

Most of the fourteen workable coal seams in the State of Missouri have high ash and sulfur levels and need beneficiation in order to meet customer and Environmental Protection Agency requirements. If proper ash and sulfur removal methods can be designed, more Missouri coals will be mined and used within the state. One of the main objectives of this research is to investigate the possibility of removal of sulfur of Missouri coals by conventional beneficiation methods.

Jan 1, 1982

By Valery Kaplan

Sulfur emission in the form of SO2 in flue gases is one of the most serious atmospheric pollutants associated with coal combustion and non-ferrous metals production. The carbonate eutectic method for removing SO2 from flue gases at 723–923 K was initially proposed in the 1970s but despite its great efficiency (SO2 concentration in the flue gas after purification reached 0.003 volume %), it could not be implemented by industry due to the complexity of the carbonate melt regeneration stage. Earlier we proposed a method suited to coal-firing power stations where the melt was regenerated using CO as a reducing agent. However, most metallurgical plants do not use coal and therefore lack a large source of CO. Here we propose a method for removing sulfur from the carbonate eutectic melt by purging it with natural gas or a natural gas/air mixture, which are available in the vast majority of metallurgical plants. This reaction leads to the reduction of sulfate to H2S gas that leaves the melt. The experiments we conducted show that nearly complete sulfur removal from the melt is possible at 823 K and that the reaction rate is sufficiently high for a large scale process. One can foresee that this carbonate melt-based SO2 removal technique may become a practical and economically attractive method for limiting sulfur emission to the atmosphere from non-ferrous metallurgical processing plants.

By Nobuaki Sato

For decontamination of SO2 containing waste gases from industries such as ferrous and non-ferrous metal companies, desulfurization with hydrogen production by the reaction of Br2 and SO2 was proposed as bromine-sulfur (BS) process. In this process, SO2 is fixed as H2SO4 in the presence of Br2 and H2O forming H2SO4 and HBr. Then hydrogen is produced by the decomposition of HBr and Br2 as byproduct is recycled. The reaction of Br2, SO2 and H2O was found not to occur in liquid phase but to occur in vapor one. The production ratios of H2SO4 and HBr showed a maximum at temperatures around 60 oC. The highest production ratio was obtained at 70 oC with a mixing ratio of Br2:SO2:H2O=1:1:10. The experimental results were discussed with thermodynamic consideration.

Jan 1, 2006

By B. R. Baldock

The converting of high-grade nickel matte for production of low-sulphur matte or nickel metal is a process which has eluded metallurgists in the past because of the limitations of conventional converting furnaces. The high temperatures required and the refractory nature of nickel oxide has prevented practical success in a process which has been known to be theoretically feasible for a long time. The Ausmelt top submerged lancing system is capable of operating under close control of the smelting conditions. High temperatures and both rapid oxidation and rapid reduction can be achieved. These features have provided the basis for successful pilot plant trials of the desulphurisation of high-grade matte from the Kalgoorlie Nickel Smelter. Sulphur level in product was lowered from 20 to 25% to as low as 0.2%, with iron levels in matte in the range of 1.0 to 3.5%. The theoretical background of matte desulphurisation is surveyed and the pilot plant operations described. The implications of the results in relation to commercial plants and possible refinery operations are summarised.

Jan 1, 1993

By He De-wen

The influence of coal desulphurization by fungus was experimentally studied. The present results suggest that fungus can effectively remove inorganic and organic sulfur in coal. The main factors that influence the desulphurization by fungus such as pH value, temperature, coal slurry concentration and coal granularity are studied by orthodox experiment and the optimal experimental conditions are as follows: pH value 6, temperature 45 C, coal slurry concentration 10% and coal granularity 100 m. Under the above conditions, fungus can remove up to 44.96 total sulfur and 54.87 inorganic sulfur within two days and their desulphurization rates will increase along with time. Compared to sulfolobas, desulphurization by fungus is steady and more effective and has the advantage of high speed.

Jan 1, 2006

By László I. Kiss, Verena Mackowiak, Alexandre Perron, Dominic Toulouse, Alicia Liedtke, Sándor Poncsák

"Bubbles play a very important role in different metallurgical applications like for example in electrowinning. During heterogeneous nucleation, the maximal size of the bubbles growing at the nucleation sites as well as the nucleation frequency is determined by the so-called detachment condition. Detachment occurs when the external forces acting on the bubble exceed the retaining forces along the solid-gas-liquid triple interface line. The phenomenon depends strongly on the shape and orientation of the solid surface and on the nature and strength of the external buoyancy and drag forces. In the present study the detachment conditions of bubbles from downward facing horizontal and inclined plates were studied experimentally under the effect of gravitational and hydrodynamic forces. The results show the deformation of the bubbles under the effect of the external forces and the detachment conditions as function of the bubble volume.IntroductionIn heterogeneous nucleation bubbles are generated at the so-called nucleation sites along the solid-liquid interfaces. They continue to grow there and after they reached a certain size they detach from the solid surface and leave the nucleation site. This scenario is well known both in boiling and electrolysis. During the growth period a stable equilibrium exists between the forces that retain the bubble at the nucleation site and the forces that try to remove it. This equilibrium evolves with the increasing volume of the bubble to the point when the detachment forces overcome the retaining forces.The life of a single bubble generated by heterogeneous nucleation can be divided into two periods separated by the detachment - or in other words by the departure - of the bubble: first the growth at the nucleation site and then the movement away. The knowledge of the detachment conditions makes possible the determination of the maximal volume of the bubble at the nucleation site that, in tum, makes possible the determination of the nucleation frequency. This is why so many researches have been directed toward the clarification of the details of the bubble detachment in the past decades. The equilibrium between the attaching and separating forces depend on the presence of body, surface and flow induced forces in the liquid, on the geometry and orientation of solid surface, on the properties of the solid-liquidgas system etc."

Jan 1, 2004