Search Documents

By G. Gomathi, K. Asokan, K. Subramanian

An electrochemical reactor with anode and cathode chambers separated by a composite perfluoro polymer cation exchange membrane was designed, fabricated and used for the reduction of dissolved carbon dioxide under ambient conditions to formate. The flow reactor enhanced the mass transfer of carbon dioxide compared to the batch reactor. Experiments were conducted using two different perfluoro polymer membranes - Nafion 961. Efficacy of CO2 reduction on various cathode materials (Cd, Pb, Sn and Zn plated stainless steel woven mesh) were determined. Optimum values of flow rate and current density were evaluated for the energy efficient formation of formate in aqueous KHCO3 (pH 7.5-8.5) buffer solutions.

Jan 1, 2008

By I. Hilerio

Chromium Nitride (CrN) thin films were deposited on AISI steel 316 substrates by means of the reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a DC source. For the second coating a negative substrate bias voltage was applied. X ray diffraction, quantitative energy dispersion and scanning electron microscope were employed to characterize the two different phases, their chemical composition as well as their microstructure. In addition, a microhardness test was carried out. The results show that a better phase formation of CrN thin films was achieved when a heating source was present (first case). Both coatings presented homogeneous surface. Their compositions show differences even when the gases flowing are the same in composition. Regarding to the hardness test results, there can be found a higher value when using a heating source.

Jan 1, 2009

By Edgar Blanco

At the Deer Trail Mine, interest in recovering noble metals from oxide ore and tailings oxide ore with 6.0/1.0 g/t Au and 200/140 g/t Ag respectively has led to metallurgic studies focused on finding an adequate treatment for these materials. Using cyanide leaching, the silver/gold recoveries from oxide ore and oxide tailings were 39%/95% and 36%/96%, respectively. Since these recoveries were less than spectacular for silver, it was decided to explore a non-cyanide leaching process that would extract silver and gold better. Based on previous research the possibility of using aqua regia in combination with sulfuric acid was evaluated. On a laboratory scale, variables such as mineralogical composition, concentration of reagents, dissolved oxygen, reaction time, pH and temperature were evaluated. Under optimal conditions it was possible to achieve >65% silver recovery and >85% gold recovery for both oxide ore and tailings.

Jan 1, 2009

By J. Rajesh Kumar

The extraction equilibrium study of tetravalent platinum was carried out using tri-octyl/decyl amine (Alamine 336) and bis(2,4,4-trimethylpentyl) monothiophosphinic acid (Cyanex 302) in kerosene from hydrochloric acid media to investigate their extraction capacity, since they have different donor atoms, ?N? and ?S?. Their distribution equlibria were studied as a function of acid, extractant, diluents and temperature. The title metal shows the inverse behavior at higher acid concentrations. Extraction of tetravalent platinum increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slopes 1±0.3, indicating the association of one mole of extractant with the extracted metal species. Stripping of metal from the loaded organic (LO) with mineral acids and bases such as hydrochloric, sulphuric, nitric acids and ammonia, hydrogen peroxide, sodium hydroxide, thio- urea were studied. Regeneration and recycling capacity of Alamine 336/Cyanex 302 and extraction behavior of associated elements was also studied.

Jan 1, 2009

By Yongfeng Jia

Lime neutralization and co-precipitation of As(V) with iron(III) is the most widely used and most economical method for the removal of arsenic from mineral processing solutions and effluents. However, the arsenate fixation mechanism in the coprecipitated solids is not fully understood. It was suggested by various researchers to be a ferrihydrite precipitation process during which arsenate is removed by adsorption on ferrihydrite. In this study, XRD, EXAFS and microprobe were employed for the speciation of arsenic and the effect of various factors on arsenic solubility was also investigated. The results indicate that coprecipitation is a more complicated process than simple adsorption resulting in lower arsenic solubilities. Poorly crystalline ferric arsenate was observed for the first time to be present in the coprecipitated solids. In case of lime as base, there exists some type of Ca-Fe-arsenate association. A general term ?coprecipitate? is suggested to describe the precipitated arsenic-bearing solids instead of those widely used specific terms ?arsenical ferrihydrite? or ?arsenic-bearing ferrihydrite?.

Jan 1, 2005

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, a three dimensional finite-volume model has been established, and the fluid flow and heat transfer in the super-wide slab mold (cross section 3250mm×150mm) of Nanjing Iron and Steel Company has been simulated. The basic feature of flow and temperature field in a super-wide mold has been analyzed, and the effects of mold width, the submergence depth of SEN, outlet angle of SEN, casting speed, superheat and cooling rate on the flow and temperature field have been investigated. The results by comparing several simulated calculations for 3250mm×150mm slab show that a more proper fluid flow and temperature field in the super-wide mold can be obtained with 15°outlet angle, 120~150mm submergence depth of SEN and 1.2~1.4m/min casting speed. The results through numerical simulation provide a theoretical basis for optimizing the configuration design of SEN and choosing reasonable processing parameters for the continuous casting mold of super-wide slab.

Jan 1, 2009

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By Elli Nurminen

Sulphate decomposition was studied in the conditions of a typical copper flash smelting heat recovery boiler. The aim was to determine the kinetics of the copper sulphate decomposition reactions and to find out if they are likely to take place in the process conditions prevailing in an industrial HRB. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process. Thermal decomposition of sulphates was studied by thermogravimetry. The experiments were conducted with a commercial copper sulphate, a partially sulphated copper oxide and an actual process flue dust. The main variables studied were temperature and gas composition of a N2-O2-SO2-mixture. The samples were characterized with SEM, optical microscope and XRD. Temperature affected the decomposition rate strongly but the gas composition had a minor effect on the kinetics. The decomposition was fastest in the partly sulphated oxide and slowest in commercial copper sulphate. Keywords: Sulphate decomposition, flash smelting, heat recovery boiler, flue dust

Jan 1, 2004

By Hemraj Dangi, S. Murali, Bhisham Yadav, Mohini Saxena, P. Asokan

"Demonstration studies were carried on the use of fly ash as soil modifier and supplier of micronutrients to improve the agricultural productivity based on the process optimised at lab scale at Advanced Materials & Processes Research Institute, Bhopal. The field trials were conducted in Uttar Pradesh (North India) Orissa (South Eastern India) and Madhya Pradesh (Central India) under different soil and crop conditions. 100-650 tonnes of fly ash per hectare were applied depending upon the soil and fly ash characteristics. Both short and long term studies on impact of fly ash on soil and food quality were conducted. With the fly ash application, the edible yield of tomato, cabbage, potato, wheat, pea, onion, paddy, sunflower, maize etc., were increased from 12 - 46% as compared to the control soil where no fly ash was used. The crop response to various elements mainly heavy metals grown in soil and fly ash applied soil was found comparable to that of control, which are within the permissible limits and meet the food quality standards. The results of impact of fly ash on biotic and abiotic properties of soil, along with the quantity and quality of agricultural produces generated under pilot scale demonstrations in three different parts of India are discussed in this paper. The outcome of this work could act as guiding force for confidence building and to maximise the use of fly ash, generated from thermal power plants worldwide as one of the major mineral waste for agriculture purposes.IntroductionThe advantages of application of fly ash in terms of improvement of soil properties and crop yields have been published by various researchers in India and abroad. Attention is also given about the possible negative and beneficial impact of pond ash in agriculture due to presence of heavy elements, radioactive nuclides and plant nutrients in fly ash. It is evident from the analysis of Indian fly ash that the presence of heavy elements and radionuclides levels are comparable with normal soil. The positive impact that has been reported is with regard to germination, yield and crop growth. The significant impacts are: long term effect of heavy and toxic elements content of fly ash on soil and up take of these elements by plant. Pilot scale demonstration studies have been completed with varying soil crop-combination under different agro-climatic conditions showed considerable improvement in the productivity of cereals, oil seeds and vegetables."

Jan 1, 2008

By Hector Carreon

This paper presents experimental data for the magnetic field produced by thermoelectric currents around uncracked hard-alpha inclusions in a Ti?6Al?4V specimen under external thermal excitation for different nitrogen content ranging from 1.6% to 5.9%. According to our preliminary results, the magnetic flux density measurements were found to be rather sensitive to changes in nitrogen content with the exception of the intrinsic material background magnetic signal that affected deeply the detectability of inclusions and imperfections in non-contacting thermoelectric measurements. Hopefully, these preliminary results can help identify a non-destructive test method that can detect material inclusions with a level of nitrogen that could be detrimental to Ti?6Al?4V alloy components.

Jan 1, 2009

By John L. H. Patterson

Handheld XRF has become the favorite way of measuring the content and identity of alloys in the field. This is because of the very portable nature of the instrumentation and its simple operation. However, these analyzers have been unable to determine the concentration of the light elements like Mg and Si due to the very low energy of the x-rays produced by these elements. In the past accessories such as vacuum and He flush have given some analyzers the ability to determine these light elements with modest detection limits. The introduction of the Silicon Drift Detector (SDD) into this class of instrumentation has added a new level of analysis capability to portable XRF instrumentation. X-ray fluorescence is achieved by exciting a sample with a beam of x-rays, which in recent portable equipment are generated by a small tube. This results in the emission of characteristic x-rays from the sample under test. By measuring the energy of each x-ray it is possible to determine what element generated it. By counting the number of x-rays at each energy it is possible to determine the concentration of each element. The detection limit for each element is dependent upon the number of x-rays which reach the detector. As the number of x-rays increases the detection limit will improve. One of the major factors in an x-ray reaching the detector is the energy of the x-ray. As the energy of an x-ray increases the probability of that x-ray reaching the detector increases. The energy of an x-ray is inversely proportional to the atomic number (AN) of the element generating the x-ray. For example, an iron x-ray (AN=26) is 6.40 keV while an aluminum x-ray (AN=13) is 1.49 keV. As the energy decreases, the detection of the x-ray becomes less and less probable because the x-ray may be absorbed by the windows which are part of the instrument and detector or the air in the path between the sample and detector. In SiPIN based portable XRF analyzers, the lowest element which is detected with acceptable detection limits is normally considered to be Ti (AN=22). The detection limits for 60 second measurements on typical SiPIN XRF analyzer are given in Table I. Thus, portable analyzers have not been useful for measurement of aluminum and titanium alloys as major components of these alloys are Mg (AN=12), Al (AN=13) and Si (AN=14).

Jan 1, 2009

By Selim Coskun

In this study, tungsten matrix composites reinforced with 2 wt% TiC particles were mechanically alloyed (MA?d) for 3h, 6h, 12h and 24h. 1 wt% Ni is used as sintering aid which is added before and after mechanical alloying. Microstructural and phase characterizations of composite powders and sintered samples were carried out via SEM and XRD analyses. Furthermore, density and hardness measurements of as-consolidated and sintered samples were carried out. Additionally, DSC experiments were conducted to investigate the sintering behavior of the MA?d powders.

Jan 1, 2009

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"Iron and steel making processes give rise to large amounts of usable and unusable materials, the latter generally being termed wastes. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. This paper defines the concept of “waste-free technology”, discusses its development in the steel industry and highlights the benefits of the technology to the manufacturing sector and the environment. The paper also articulates how the “waste-free” technology could be applied in the proposed Ajaokuta integrated steel plant in Nigeria.IntroductionIn the past, nature was considered an inexhaustible store. Its resources were consequently exploited and waste products therefrom were discarded. Today, attitudes have not changed appreciably even as raw materials cost rise by the year to pose a series of socio-economic problems, which, among others, may include the rational and optimum utilization of resources, environmental protection and reduction of waste formation. Consequently, industrialists now face unexpected regulatory pressure in areas of pollution prevention, waste minimization and hazardous waste disposal.Iron and steel making processes give rise to significant amounts of usable and un-usable materials, the latter generally being termed waste. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. In this paper, the term waste refers to those materials that are either irrationally utilized or, land-filled and part of the byproducts that are not utilized. It includes that part of used materials which is not incorporated into the products manufactured during a process stage and which in contrast to reuseable materials, is considered not suitable for any further use, owing to technical or economic factors. In general, these materials are inorganic and parts of them are either utilized or passed to the other processes; the other part should be disposed of using well-established waste disposal practices to avoid any environmental threat.Thus, creative methods must be developed to modify the manufacturing processes to reduce emissions and process wastes by fully utilizing all resources. One method of eliminating the negative effect of waste formation is the use of purification and cleaning structures (pollution control system, PCS). These are, however, quite expensive."

Jan 1, 2008

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009

By Liyuan Chai

The corrosion mechanism of A3 steel induced by chloride ions in the purified water had been investigated with the A C Impedance technique. The results showed that there were another two factors which determined its electrochemical corrosive rate: the electrode potential and coverage ratio of chloride ions on the surface of A3 Steel. The corrosion mechanism of A3 steel in the solution with chloride ions emendation was two steps of electrode process with the rate-determining step of 0,32kFeClFeCle+--¾¾®++.

Jan 1, 2009

By W. F. Drinkard

Many in the environmental movement have focused on this element. But, nothing they or anyone does will change the amount of arsenic in the world. This report is on actual commercial plants that we developed and operated to recover or stabilize arsenic values from metallurgical dusts from gold and copper pyro operations and arsenical gold bearing ores. When they were available gold and copper values were recovered. Our experience in arsenic extends over thirty years. My first corporation, Mineral Research & Development Corporation was the first in North America to manufacture the then new CCA (copper-chrome-arsenic) wood preservatives. This class of wood preservatives proved to be so effective that it made wood into an entirely new material of construction. It is not uncommon for wood properly treated with arsenical CCA preservatives to last for thirty; forty, and sixty years. Over a hundred years have been projected in some field tests. Hundreds of thousands of trees have been saved. Millions more trees would have been saved had environmentalists not decided that their arsenic phobia was more important than trees. There are several variations of CCA. The most popular is CCA-C. Its formula is: CrO3 . . . . . . . . . . . . . . . . . . . 47.5% CuO . . . . . . . . . . . . . . . . . . . 18.5% As2O5 . . . . . . . . . . . . . . . . . 34.0% Until recent restrictions were placed on the consumption of arsenical wood preservatives, annual consumption in North America was about 150,000,000 lbs./yr. About 64,500,000 of arsenic as the pentoxide was safely consumed this way. World CCA consumption has been about double the above figures or 300,000,000 lbs. as 100% CCA and 129,000,000 lbs/yr as As2O5. Close to 100% of all the arsenic used in wood preservatives is derived from gold or copper processing. The valence of arsenic required for CCA wood preservatives and many other markets is the same valence that is required for stabilization. The economic challenge is how to get there. We have built and operated eleven plants to oxidize arsenic trioxide to its pentavalent form. Most of these have been classic in that they used a common oxidants such as hydrogen peroxide or nitric acid to achieve this.

Jan 1, 2005

By Jewel Gomes

Green rust is an important intermediate in oxidative transformation of Fe(II) phase. This unstable compound contains a mixture of ferrous and ferric hydroxides that belong to a family of minerals known as layered double hydroxides (LDH). Its general formula is [FeII(6-x) FeIIIx (OH)12]x+[Ax/n-*yH2O] x-, where A is an n-valent anion mainly Cl-, CO3-2 and SO4-2, and in which either the bivalent or the trivalent iron can be replaced for other trivalent or bivalent metal ions. It was first identified as corrosion product, later in soils as a product of interactions between microbes and metals in soils. Due to its high reactivity, it is used in the reduction of organic and inorganic compounds, As removal, and the treatment of acid mine drainage. In this paper, we described the method of electrochemical generation of green rust, its characterization by XRD, SEM and FT-IR, and its implications to electrocoagulation.

Jan 1, 2009

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Zhongning Shi, Ramana G. Reddy

"By cyclic voltammetry and potentiostat electrodeposition using Potentiostat/Galvanstat, electrochemical behavior on Ag electrode in electrolyte 0.2M NaOH+0.01MPb(NO3)2-0.01M TeO2 -0.01M TlNO3 solution were also carried out at 298K. The processes of electrodeposition of Tl2Te3 and PbTl4Te3, a thermoelectric material, are reported along with analysis of the composition of the obtained deposits. The results showed that two different underlying processes are occurring depending on deposition potential. One process involves the reduction of TeO3 2- and Tl+ to Tl2Te3 in a potential interval of -0.70V < E < - 0.89V (vs. Hg/HgO). A second process at more negative reduction potentials involves reduction of TeO3 2-, Pb2+ and Tl+ to PbTl4Te3 in a potential interval of -1.02V < E < - 1.19V. The crystalline Tl2Te3 and PbTl2Te3 were deposited electrochemically on Ag substrates at -0.84V and -1.10V respectively. Thermoelectric (TE) material can form a temperature gradient across the material to make electric voltage, which is popular in waste heat utilization and recovery industry. Lead telluride, PbTe, is a small band gap semiconductor of 0.32eV at 300K. PbTe can change its n-type semiconductors with Pb-rich to p-type semiconductors with Te-rich[1]. And it is one of the best TE materials used in thermoelectric generators working between 500K and 600K, or even at a higher temperature of 800K.Three facto,rs play a role in the performance of a thermoelectric material: electrical conductivity (s), thermal conductivity(?), and the Seebeck coefficient (S). These can be combined with absolute temperature (T) to give a figure of merit (ZT) for the material, ZT = s2sT/?. By increasing the electrical conductivity and decreasing the thermal conductivity, which can enhance the ZT value, many efforts, such as alloying with other elements and making the materials nano-sized, have been done to improve its properties recently. Hsu et al. reported that the ZT value of Cubic AgPbmSbTe2+m is increased to 2.2 by doping Ag-Sb to PbTe.[2]."

Jan 1, 2011