Search Documents

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By Hyung-Min Kwon

There are a number of methods available that can be used to estimate the bearing capacity of piles that are subject to lateral load, such as the theory of subgrade reaction or the elastic continuum approach. The objective of these approaches is to determine the lateral load corresponding to the allowable lateral displacement of the pile. It is important to select the appropriate soil stiffness when analyzing soil behavior within the allowable displacement of piles because the stiffness of soil is dependent on the displacement of piles. Even though pressuremeter tests can measure the stress-strain behavior within a wide strain range, pressuremeter test results have been utilized to assess only the fragmentary soil modulus based on either semi-empirical correlations or analytical approaches. This study is concerned with a methodology that can estimate the horizontal deformational property, while taking into consideration the nonlinear deformational characteristics of sandy soils. Pressuremeter tests were conducted for 15 cases using a calibration chamber. Reloading curves were employed in the estimation of horizontal deformational property in order to minimize the effect of soil disturbance caused by the installation of the probe. The shear modulus degradation characteristics were estimated from the curve fitting for the reloading curve and from extrapolation using the exponential function. In addition, the difference was taken into account between the stress state around the probe in reloading and that of the in-situ state. A consistent relationship was observed between the maximum shear modulus taken from the suggested method and the bender element tests performed in the calibration chamber, simultaneously with the pressuremeter tests. In addition, the results showed significant concurrence with the well-known empirical correlation.

Jan 1, 2008

By Jiu-ju Cai, Wen-chao Liu, Fei Liu

"The material flow of urban eco-industrial system includes linear flow, recycling flow, branching flow, converging flow, etc., which consequently lead to the system complexity. Comparing the urban eco-industrial system to ecosystem, it can be concluded that this complexity is caused by the system adaptability. In the system, the interaction and adaptability between the agents themselves and between the agents and the environment stimulates the changes of material-flow mode, which lead to the evolvement from traditional industry to the eco-industry. Focusing on the evaluation of this evolvement process, two material-flow models are established in this paper, one of which is for the system itself and the other for the agents in system. The latter model is applied to analyze the interrelationships among mass, energy and pollutant flow in the iron and steel industry, and to make the direction clear to improve the resource and energy efficiency and decrease the environmental load.1 IntroductionIndustrial system is a subsystem of urban system, and they are interconnected and interrelated through material flow. The industrial development causes the urbanization. But the traditional industrial mode, characterized by high consumption, high pollution and low efficiency, also causes the “urban problems”, and leads to the reduction of resources carrying capacity and the increase of environmental load. Nowadays a lot of researches focus on how to realize the sustainable development of industries and cities. Thus comes the urban eco-industrial system guided by industrial ecology.Regarded as a Complex Adaptive System (CAS), the urban eco-industrial system evolves for quite a long time. According to Holland’s description on CAS, CAS consists of adaptive agents, which interact with the environment and other agents, learn and accumulate experiences, and accordingly change their own structures and motion modes. In this way, the evolution of the whole macro system is improved [1]. The evolution from traditional industrial system to urban eco-industrial system is mainly reflected in the variety of internal material flows which include not only linear flows but also recycling flows. Therefore, to construct models which clearly analyze industrial metabolism, is of great importance to evaluate industrial system evolution.The article is organized as follows: Section 2 describes the urban eco-industrial system. Section 3 presents the system-oriented metabolic analysis model and the agent-oriented one, analyze the interrelations of energy flow, material flow and pollutant flow in Chinese iron and steel industry through the latter model, and indicates the directions of improving the resource efficiency and energy efficiency, and decreasing the environmental load. Section 4 concludes."

Jan 1, 2008

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Juhyung Lee

Recently, large diameter drilled shafts are often used for foundations of large-scale marine bridges with high capacity and required to resist lateral loads. Steel casings are essential in supporting the hole-diving concrete installation of the drill shafts constructed in the sea. The casings, however, are usually not considered as the structural elements and their load bearing capacity is often overlooked in the design of drilled shafts. As the diameter of drilled shafts becomes larger, there are higher demands for more efficient and economical design of large-scaled drill shafts in the sea. Steel-concrete composite columns are popular for the superstructure of bridges, and the outer steel attached to the shaft increases the shaft resistance through confining the concrete. In this study, the lateral resistance of steel-concrete composite drilled shafts was evaluated quantitatively based on the numerical analysis. When steel casings are used as structural elements such as the composite columns. Ultimate lateral bearing capacity of composite drilled shafts with various diameters was numerically calculated through the 3D finite element analysis. For that, elasto-plastic model with the perfect plasticity is involved to capture the ultimate load. A commercial FEA program, MIDAS-GTS, is used in this study. Real field conditions of the west coast, Korea were examined to set up the ground conditions and pile lengths required for this parametric studies. Detailed characteristics of the stress and displacement distributions are evaluated for the better understanding on the mechanisms of the composite shaft behavior.

Jan 1, 2008

By N C. White, L Danyushevsky, D R. Cooke

Comb-layered textures preserve the cyclic accumulation and release of volatiles inside magmas that are temporally associated with large Cu-Au-Mo-rich porphyry ore deposits. Fluid inclusions in these textures sample pristine magmatic fluid. Microanalysis of this fluid helps constrain the physical models that operate at melt-fluid interface and in the broader magma system responsible for ore deposit formation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Marilda Macagnan, Rosana de Cassia de Souza Schneider, Valeriano Corbellini, Tiago Bjerk, Mariela de Souza Vieira

The great potential of Brazil for the agricultural production makes our country a generator of agro industrial residues. In this context, the solid-state fermentation appears as a technology that shows alternative ways for those residues, adding values to these raw materials, through the production of substances of industrial interest, besides reducing the possible environmental problems. The main objective of this study was to apply the bovine fat residue associated to the garden grass for the fungal lipase production. Initially, 75 microbial cultures were isolated from garden grass samples after incubation of the mixture with bovine fat. From these cultures were selected the filamentous fungi, whose lipase production abilities were evaluated. The isolation and the selection were accomplished by using a differential culture medium containing Tween 80 as inducer substrate of lipase production. The colonies with lipolytic potential were detected by the presence of white precipitation haloes on the agar. With agro industrial residues the best lipase producer fungus was identified as Penicillium sp in 6 days of solid state fermentation. The crude enzyme obtained was tested in transesterification process for the biodiesel production.

Jan 1, 2008

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

By Z. A. Md-Nor

Risk management is an established loss-control methodology that has been applied successfully in many industries. Recently, interest in this structured approach has grown in the mining industry. The main objective of this research was to develop a risk-assessment process, which is a part of risk management, that can be used by the U.S. mining industry to more thoroughly characterize risks associated with haul truck-related fatalities. The assessment is based on historical data obtained from the U.S. Mine Safety and Health Administration (MSHA) investigation reports, which includes 113 fatal incidents that occurred from 1995 through 2006. The risk-assessment process used in this research involves the following basic steps: identification of the risks, risk analysis and risk evaluation. The preliminary hazard assessment (PHA) method is used in identifying and quantifying risks. Risk levels are then developed using a pre-established risk matrix that ranks them according to probability and severity. The resulting assigned risk value can then be used to prioritize control strategies. This paper is a part of a detailed study on risk assessment for equipment-related fatalities in mining sponsored by the Western U.S. Mining Safety and Health Training and Translation Center.

Jan 1, 2008

By Raymond Hofstetter, Paul Worsey

The purpose of this paper is to investigate commonly used methods for mitigating the effects of shrapnel from linear shape charges (LSC) used in the demolition industry. Primarily the problem is not that shrapnel poses a threat to human bystanders, but rather it can affect the other charges in the demolition or damage to structures in close proximity to the charges. This research aims to determine what methods have success at stopping shrapnel, what methods do not, and to promote an awareness of the dangers of using the LSC without any protection. The project was carried out at the Experimental Mine site at the Missouri University of Science and Technology. This research is an undergraduate research project to fulfill the requirements for the Explosives Engineering minor program at MST.

Jan 1, 2008

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

X-ray analysis of polycrystalline powder samples has grown beyond its roots in the world of laboratory research and is now regarded as one of the most powerful industrial process-control tools in the field of building materials. This is the key to characterise the element and crystalline phase composition of the material. This is due largely to the development of industrial X-ray analytical systems such as PANalyticalÆs twin solution, which has transformed the advanced analytical techniques born in the laboratory into a robust, workmanlike and easy-to-use tool for todayÆs heavy industries. The increasing use of alternative fuels makes the Bogue method less reliable. Therefore, the real phase quantification by the Rietveld method is the only choice. Additional fine-tuning of the Rietveld method by using alternative methods guarantees the most accurate quantitative results. Moreover, the recent development of ultra high-speed X-ray detectors allows for æon the flyÆ quantitative X-ray diffraction analysis and a truly interactive process and quality control.

Jan 1, 2008

By Shirley Cosin, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Jorge E. Di Rito, Valquiria F. J. Kozievitch

"A procedure that is being studied as a potential method for correct disposal of industrial wastes by incorporation on common clay bodies in the fabrication of structural ceramic products as bricks, blocks and roof tiles. The objective of this paper is to present the results obtained with mixtures of unburned sanitary ware wastes with a common clay from Jundiai, São Paulo, Brazil. Preliminary tests of incorporation (1,0% to 30,0% in weight) were made with hand formed spherical test bodies. With the proportion that presented spheres with the higher compression strength after drying and after firing (950°C) prismatic samples were extruded. Based on the ceramic properties of those mixtures an industrial test was performed. Six hundred hallow blocks containing 30% waste were fabricated and presented ceramic properties similar to those without incorporation. Introduction The sanitary ware segment has a very great prominence in South America, placing Brazil as one of the greater producers of the world.. Inside the country, the city of Jundiai, in the State of São Paulo is the greater producer region of this ware. Great part of the material is destined to exportation and daily it is produced high number parts. High exportation requirements make that the amount of powder waste rejects reach astronomical volumes. Until the moment too small part of that material it is re-taken with advantage, because in the own segment, there is not an economic viability, by the fact of the exigencies concerning the quality of the final product [1]. If from one side it exists that material that at the moment is deposited in landfills, or stored at the patio’s factories, from the other side the exigency of adopting exploitation rules, recycling and obedience to Laws relative to the environment as ABNT 10400, therefore it is a material that if well studied, it will certainty have a noble destiny [1]."

Jan 1, 2008

By M Sykes

Gold was initially discovered at Ballarat in 1851. After initial alluvial mining, underground quartz mining commenced in 1853, continuing until 1918. The historic miners were considered to be capable of mining anywhere in the world after overcoming the difficult conditions within the Ballarat goldfields. Whilst mining has changed dramatically since the early 1900s the challenges with underground mining at Ballarat have not. Modern pumping systems cope with the moderate water inflows. However, modern machinery and efficient mining methods influence opening sizes and extraction techniques. In some cases modern techniques have accentuated the challenging ground conditions and complex orebodies that were faced by the historic miners. As the Ballarat East project has progressed towards production, technical challenges relating to geomechanics and mine planning are being resolved resourcefully.

Jan 1, 2008

AustraliaÆs success as a mineral producer and exporter rests heavily on its technological competence. That competence is based not just on adopting internationally-developed technology but also on ground breaking research conducted at Australian research institutions, many of which have global reputations. A number of forces are now operating to speed the introduction of advanced technology to mining and processing operations around the globe and this will create pressure on the Australian industryÆs ability to retain its competitive edge. Examining the foundations of that national research base and the associated culture of innovation may provide some guide to the dynamics that will be required to maintain technical competitiveness in the future.

Jan 1, 2008

By Arthur M. Langer

Since the promulgation of the first Federal Asbestos Standard by the Occupational Safety and Health Administration in 1972, other federal agencies have modified the standard to better carry on their own unique missions. The instruments used to identify and measure asbestos, the sampling protocol, and the criteria used to define asbestos, have been modified to some degree. The Mine Safety and Health Administration regulates and controls asbestos dust in the mining and mineral commodity industries. However, crushed stone and processed ores contain mineral fragments that are frequently difficult to distinguish from asbestos. Mineral nomenclature, instruments for particle analysis, and sampling strategy must be accommodated to some degree to make asbestos control workable and meaningful. Precedent in other agencies has made consideration of these changes possible. Newly identified amphibole asbestos minerals have further complicated the agency?s regulatory charge. Changes in its Asbestos Standard are now being considered. Crushed taconite ore in the Eastern Mesabi highlights many of these issues. ©2008 Published by Elsevier Inc. Keywords: Amosite; Grunerite asbestos; Crocidolite; Riebeckite asbestos; Tremolite asbestos; Actinolite asbestos; Winchite asbestos; Richterite asbestos; Arfvedsonite asbestos; Fluor-edenite asbestos; Asbestos defects; Cleavage fragment; Mineral habit; Mesabi amphiboles

Jan 1, 2008

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, F. G. Hampel, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides can be incorporated for use as a transmutation fuel. The current study involves characterization of precursor powders and pellets destined for the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of minor actinide mixed oxide (MAMOX) with oxygen to metal ratios (O/M) of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders were characterized using a field emission gun scanning electron microscope (FEG-SEM) to determine particle morphology, size, and size distribution. An electron probe microanalyzer (EPMA) was used to characterize element distributions in the pellets.IntroductionThe fundamental purpose of GNEP is to enable a fuel recycling partnership between member nations. The customer nations utilize the fuel for electricity generation provided by and subsequently recycled by the supplier nation. The supplier nation recycles the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials are strictly controlled through the International Atomic Energy Agency. One of the thrust areas supported by the GNEP program is the development of actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3].MOX fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition into which minor actinides can be incorporated for use as a transmutation fuel [4]. Irradiation performance data on oxide fuels with high concentrations of minor actinides is limited, which has prompted this study. This paper discusses the characterization results of precursor powders and pellets prepared for the Advanced Test Reactor in Idaho to determine the effects of including minor actinides in the fuel, and addresses two fuel test matrices proposed by Hilton et al. [3]. The pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of MA-MOX with O/M of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders, uranium oxide (depleted, DUO2 and highly enriched, HEUO2), neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a FEG-SEM for particle morphology, size, and size distribution. The morphology of the actinide powders was studied in the areas of flowability and porosity in order to predict manufacturability. The MOX pellets were characterized using an EPMA in order to determine impurity levels and locations."

Jan 1, 2008