Search Documents

By V. C. Kelessidis

Demand for multifunctional drilling fluids continuously increases. In the quest for more hydrocarbons, drilling has extended to deep water areas (now in excess of 2.000 m) and to very deep wells (now in excess of 6.000 m). In these extreme conditions, low temperatures, as low as 1-5°C on the sea bed, high temperatures, in excess of 200°C, and high pressures, more than 1.000 bars, in the bottom of the well, are frequently encountered. In these harsh environments, synthetic oil and oil based drilling fluids are used, but the former are expensive while strict environmental requirements have limited the use of the latter. Thus, drilling industry has turned back to water based drilling fluids which use bentonite as primary viscosifier and as a fluid loss control additive. However, in conditions of high temperatures, bentonite suspensions gel and loose their exceptional low temperatures properties, thus, additives are needed to overcome such problems. In this article we review these challenging drilling environments and establish the requirements for the multifunctional drilling fluids. Our research indicates that demand for continuing use of bentonite by drilling fluid industry is strong. Furthermore, we bring forward the opportunities for new additive development which can expand the operational ranges of bentonite suspensions.

Jan 1, 2007

By Enrique Fernandez

M-30, Madrid’s inner ring, covers 42 sq km of the city centre where one million people reside. It was constructed in several phases during the sixties and the eighties. The design criteria applied to those phases were different and were not always homogeneous with urban roads with lighting regulation as well as speedways. These areas had a heavy concentration of access and exits and there had been made many changes on the number of traffic lanes which has caused heavy traffic congestions and high accident rates. The environmental impact and noise pollution in residential areas are also consequences of M-30. The Madrid Major took a decision at the beginning of the present legislation, based on socio economic and environmental evaluation; rebuild the M-30 with the following sustainable mobility principles: Underground transfer of a considerable portion of the main ring and some of its links replacing some parts of the surface with new green areas in order to reduce the environmental impact. Increase the traffic capacity, improving the traffic continuity and fluidity and eliminating the lighting regulation areas, which is one of the main congestion problems currently. Increase the traffic safety with clear signalling information panels and avoiding difficult maneuvering. Redesign the links with the high capacity radial highways and other connecting lanes of the city. The project is worth 3.7 billion Euros. In 2007, when the construction is completed, it is expected will save 14 million of journey hours that represent 4.5 million Euros saved in fuel consumption per annum, There will be a very significant reduction of 35,000 tons of CO2 in terms of pollution and 400 less car accidents. Those values will increase even more in the following years. The areas beside Manzanares River, running parallel to the M-30 on the western side of Madrid, will be highly enhanced. Better water quality and the recovering of the green areas existing in old times will also return for the citizen’s enjoyment. TUNNEL CROSS SECTION OF CALLE 30 SOUTH BY PASS One of the major challenges of the new Calle 30 is actually not only the related to the main road but also to the link with the A-3, with highway to Valencia. This link is currently the most congested area and has one of the highest traffic densities of Spanish roads, with more than 250,000 vehicles/day. The remodelling of this area is the principle objective of the South by-pass. The tunnel is the only answer for this by-pass as the road alignment will go among buildings. A twin tube design, one for each direction, with three lanes allowing the circulation of both, light cars and heavy trucks, is the solution that has been

Jan 1, 2007

By F. Parada, R. Parra

"The neutralization process of SO2 from coal burning plants is a well-defined technology using limestone to form CaSO4 according to the following reaction: CaCO3 + SO2(g) + 1/2O2(g) = CaSO4 This paper presents the results of a study carried out to validate the option of capturing SO2 using gases from a non-ferrous smelter; SO2 content was up to 12% using a three-stage fluidized bed reactor. The difference in SO2 content affects equilibrium conditions and kinetics, rendering a direct extrapolation of the high efficiency achieved for low SO2 content impossible. The R&D program consisted of a laboratory study using a semi-pilot operation of a one-stage fluidized bed reactor and the construction and operation of a three-step reactor prototype. Results show that the reaction proceeds according to the unreacted core model that imposes a compromise between CaCO3 conversion and SO2 capture. For high SO2 capture, the calcine from the reactor contained CaSO4 and CaO. A complete capture of SO2 from gases with 8 vol.% can be achieved with a mean reaction time of two hours at 800°C."

Jan 1, 2007

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By J. Nell

Heavy mineral deposits often contain relatively high levels of radioactive elements (thorium and uranium in particular).It is difficult to obtain clean separation of ilmenite and monazite (the main impurity mineral containing radioactive elements), and physical intergrowths of the two minerals are, in fact, not uncommon. As a result, ilmenite concentrates obtained from such deposits often contain high levels of thorium and uranium. Because of the large negative free energies of formation of ThO2and U3O8boththorium and uranium report to the slag during smelting and if an ilmenite concentrate contaminated with monazite is used to make high titania slag, the concentrations of these elements in the slag end up about 40% higher than in the ilmenite feed. Previous work, patented by RGC Mineral Sands Limited, and subsequently confirmed by Mintek, showed that radioactivity may be reduced by roasting an ilmenite concentrate with borax at 1000°C to 1100°C and leaching it with hydrochloric acid1. It is evident that the cost of an ilmenite roast/leach process will be high and there may be economic benefits in removing the radioactive elements from the slag instead (the volume of slag to be treated is smaller than the volume of ilmenite feed). To remove radioactive elements from the slag it is necessary to know how these elements occur in the slag. Inother words, the distribution of uranium and thorium between the various oxide, silicate and metallic phases in high titania slag must be determined. Once the deportment of thorium and uranium between the various phases ha sbeen determined, an appropriate process for slag purification can be developed. Test samples High-titania slag was prepared in a pilot-scale DC furnace from ilmenite concentrates with different levels of uranium and thorium. Subsequently, ten slag samples representing a range of compositions were selected for bulk chemical analysis, scanning electron microscopy and micro-analysis. The samples were crushed to a maximum particle size of 1 mm and from each sample a 20-kg batch was riffled out for analysis. Bulk chemical composition Chemical compositions of the samples selected for test work are given in Table I. TiO2, Al2O3, SiO2, MgO, MnO, FeO and V2O5were analysed by ICP-OES, Na2O, CaO andCr2O3by atomic absorption spectroscopy and U and Th by XRF (the XRF detection limit for U and Th was around 4 ppm). The ?B? series has a higher silica content than the others as a result of small silica additions that were made during smelting. All samples have elevated alumina levels as a result of furnace refractory contamination during smelting. As expected, there is an inverse relationship between the concentrations of TiO2and FeO in the samples (Figure 1).The TiO2and FeO levels are similar to the levels found in industrial slags2. Extreme conditions of reduction under which reduction of more ?refractory? oxides (e.g., chromia, magnesia, silica, alumina and even urania and thoria) might take place were not explored in the study. Note that BB1and BBB1 contain more than 7% combined silica and alumina (SiO2as a flux addition during smelting, and Al2O3from refractory contamination) and they do not fall on the general trend defined by the other samples. The U and Th concentrations of sample E2 is noteworthy. In the preparation of slag E2, monazite concentrate was added to the ilmenite to increase the concentrations of radioactive elements in the slag. This was done primarily to facilitate the detection of Th and U during the phase chemical characterization of the slag. Radioactivity measurements Gamma ray emissions from the samples were measured [ ]

Jan 1, 2007

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By Z. Mubarok

An overview of the problems encountered the electrorefining of copper anodes containing high levels of nickel and antimony is presented. Our investigations have been focusing on the passivation behaviour of the anodes with high contents of Ni, Sb, Sn, and Pb, the formations of kupferglimmer and floating slimes. The results of linear voltammetry, chronopotentiometry and electrolysis test revealed a noticeable lower resistance of the anodes to passivation in comparison to those with lower contents of Ni, Sb, Sn, and Pb. Anode containing kupferglimmer exhibited oxygen gas evolution during the passivation state. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) indicated that tin can replace and/or join antimony in the kupferglimmer structure. Under specified experimental conditions, floating slimes precipitations took place with high Ni, Sb, Sn, and Pb anodes prior to the end of one anode period.

Jan 1, 2007

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007

By A Jurg, F Leclercq

The total drill and blast concept is widely known in the mining industry. On the contrary, the quarry industry rarely adopts such working methods. Based on the experience of the CBS quarry in the North of France, this paper shows how up-to-date blasting technology and simple control methods can significantly improve the overall Mine to Mill efficiency of a quarry. The CBS quarry, in partnership with the EPC group and Nitro- Bickford Company, adopted a new working process three years ago aimed at increasing blast performance and related productivity of the downstream process (loading, hauling and crushing). The pattern geometry of each blast is controlled and explosive charging is carried out following the æconstant specific energyÆ CSE concept. This method provides a homogeneous fragmentation distribution and reduces vibration peak-particle-velocities. The impact on downstream productivity is controlled by means of a simple information management system, which collects and measures key parameters of the production process such as; hauling cycles, crusher throughput, secondary breaking and vibration peak particle velocity. This information system has clearly proved over time that consistent blast quality could be achieved, leading to a 30 per cent improvement in quarry productivity. Improved energy control of blasting through optimisation with electronic detonators, allowed a significant reduction in vibration impact on the environment. Improvement in blasting security, reduction in the environmental impact and productivity enhancement are major benefits that quarries can obtain from these CSE optimisation blasting methods.

Jan 1, 2007

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By J L. Mauk

The Favona adularia-sericite epithermal Au-Ag deposit is located at the southern end of the Hauraki Goldfield, about one kilometre southeast of the world-class Martha deposit. The deposit occurs in Late Miocene andesitic lava flows and local dacitic tuffs of the Waipupu Formation. In some places, post-mineralisation ash fall and ignimbrite, up to 50 m thick, cover mineralised rocks and andesite. We collected soils samples from 110 sites along eight traverses over Favona, and from three regional lines: two south of Favona, and one north of Favona.   Analyses of soils identify prominent enhanced concentrations of Au, Ag, and Hg, and lower enrichments of Sb and As. At Favona, Au and Ag appear to be highly anomalous in areas over mineralisation with Au concentrations greater than 100 ppb and Ag concentrations greater than 1000 ppb, whereas background concentrations are approximately 5 ppb and 50 ppb respectively. The background concentrations of Hg in soils are approximately 100 - 200 ppb, but in mineralised areas, Hg generally exceeds 200 ppb, and some soils contain greater than 600 ppb. Antimony shows enrichments, although weak, above known veins and As locally shows some enrichment above areas of known mineralisation. Therefore, soil sampling at Favona defines geochemical anomalies that correlate with the position of known mineralisation at depth. Thus, there is strong empirical support for the use of Au, Ag and Hg, and possibly Sb and As geochemistry to identify mineralised trends associated with buried deposits at other epithermal prospects.

Jan 1, 2007

By M Wortley, O Gu, D La Rosa, J McMaster

Metso Minerals Cisa have developed VisiofrothÖ û a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio TintoÆs Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothÖ system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothÖ system and the parameters that are measured by the software.

Jan 1, 2007

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By John J. Sammarco

Abstract- Emergency shutdown systems (ESDs) for mining machinery provide critical functions to safeguard miners. Traditionally, ESDs were realized with simple hardwired circuits; today, there is a growing trend to use programmable electronic technology such as programmable logic controllers (PLCs). This paper describes an analytical study to quantify the safety integrity of a PLC-based ESD and a hardwired ESD. The safety integrity level of each design approach was determined by quantifying the average probability of failure on demand (PFDavg) as described by the recommendations for programmable electronic mining systems published by NIOSH and the IEC 61508 international standard. The safety analyses addressed system architecture, hardware failure probability, proof test interval, diagnostic coverage, and human error probability. The results indicated that a same level of safety, safety integrity level 3 (SIL 3), could be attained when evaluating random hardware failures. Neither approach could attain SIL 3 if manual activation was used. Human error was the limiting factor where, using human reliability analysis, PFDavg < 1 x 10-1; thus, the ESD does not meet SIL 1. It is apparent that automatic verses human¬activation of the ESD is a very important safety consideration. Manually actuated ESDs can only achieve SIL 1 regardless of the technology; therefore, additional independent safety layers of protection are needed to exceed SIL 1. Secondly, it is apparent that the technology choice is very important. The PLC-based ESD was much simpler to design and to validate safety1.

Jan 1, 2007

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By Michael Cianchetti, Nadir Ansari, Matthew Janes

"PROJECT DESCRIPTIONThe R C Harris Filtration Plant underwent an expansion to install an underground sludge treatment capability consisting of a series of underground tanks within stepped excavations 12m (39 ft) and 10m (33 ft) deep into compact, wet sands over stiff clays and clayey silts.Concerns regarding the original structure influenced designers to set the lateral deflection limit for the proximal front footing at 4mm (1/6 in), (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Through extensive Fast Lagrangian Analysis on Continua (FLAC) and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept and met deflection concerns.GEOTECHNIQUEThe hillside site drops 14.5m (47.6 ft) over a distance of 53m (174 ft) between the existing Filter Building on the north and the Services Building on the south. The soils adjacent to the Filter Building consist of 6m (20 ft) of sandy fills, to the footing elevation, over compact sands and layered dense sands and silts to a depth of 10m (33 ft) below existing footing. Beneath the silts lies a 10m (33 ft) thick stiff clayey silt, 2m (6.6 ft) of sandy silt till (containing cobbles and boulders) and an artesian gravelly sand at a total depth of 30m (98.5 ft).The tender information was deemed inadequate to accurately determine soil parameters for a finite element analysis. As a result, the design-build team performed pre-tender Cone Penetrometer Testing (CPT), including dynamic analysis. The CPT data indicated stratigraphy consistent with the conventional bore hole exploration (SPT results) however, the CPT data provided consistently superior soil strengths. The CPT data indicated the sands and silts were dense to very dense throughout their full thickness. The clayey silts below the sands were found to have shear strengths in the 100 to 200 kPa (14.5 to 29 psi) range with an Over-Consolidation Ratio (OCR) ratio of 1.5 to 2. The dynamic analysis, while low strain, indicated very competent behavior with Young’s Modulus values in the 200 to 350 MPa (29,000 psi to 51,000 psi) range. The CPT derived shear moduli and OCR values were vital in determining the soil engineering parameters used for the FLAC analyses."

Jan 1, 2007

By J. E. Nesset, S. R. Rao, J. A. Finch

"For base metal sulphides, iron rejection starts in mineral processing. This review focuses on changes in plant practice specifically to improve iron sulphide rejection by control of contaminant ion effects and discusses selected general innovations in mineral processing that can be expected to play a role. One group of changes to control contaminant ions is in size reduction (the use of stage grinding and inert stirred milling) and another is in system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy reagents). Plant examples illustrate the successes, indicating that there are several options available. The general innovations start by considering the new tools for measuring gas dispersion properties and quantifying froth characteristics by imaging. Examples of their application to improve concentrate quality illustrate the potential. Other innovations stress adapting geostatistics to model variation in milling and flotation response to provide feed forward control and rigorous application of statistical experimental methodology in plant test work. An example from one concentrator shows improvements in concentrate quality from application of basic principles can be impressive.INTRODUCTIONThe more iron control (rejection) that can be accomplished in mineral processing the lower the subsequent metal extraction costs and environmental implications of iron disposal, particularly in hydrometallurgical processes. Iron rejection has been a contributing target to periodic attempts to apply mineral processing to nickel laterites and bauxites but the prime application is control of pyrite and pyrrhotite (iron sulphides) in the treatment of sulphide ores by flotation. In this paper some new concepts and innovations introduced in sulphide flotation plants over the past ten years or so (i.e., since a previous review [1]) will be outlined with examples of how they have contributed to improved “iron control”.To increase rejection of iron minerals, first the recovery mechanism should be understood. There are four principal ones, two physical in origin: 1, via locked particles (i.e., flotation of composite particles due to insufficient size reduction to liberate the minerals) and 2, through entrainment in the water reporting to the float product (an unselective process); and two originating from a response to the system chemistry: 1, true flotation (i.e., iron sulphides becoming hydrophobic) and 2, as a result of iron sulphides forming aggregates with hydrophobic particles (e.g., ”slime” coatings). There has been considerable effort to diagnose which of these dominates iron sulphide recovery; in many cases it is due to “chemistry”, in particular true flotation. The flotation effect often appears related to contamination by metal ions [1]. This can reduce selectivity in two ways: 1, metal ion species may activate iron sulphides, or 2, cause general depression which demands more vigorous flotation conditions (e.g., additional collector) with consequent loss of selectivity. This is where the review will start, by considering ways to control contaminant ions."

Jan 1, 2007

By K Buda, W Staunton, M Hill, V Tjandrawan

One of the challenges facing the gold industry in the 21st century is the continuing need to identify new reserves of economically treatable ores. Discoveries of large, metallurgically simple orebodies are becoming increasingly rarer, forcing companies to investigate options for the processing of ores which may present recovery, economic and/or environmental issues, requiring innovative approaches to their treatment. Ores which contain naturally occurring carbonaceous material (æpreg-robbing oresÆ) are an example of one such ore type. NewmontÆs Jundee operation contains zones of carbonaceous ore within the oxidised orebody. A program consisting of detailed laboratory work and extensive plant trials has been undertaken to assess the options of the processing of this material. Laboratory tests demonstrated the advantage of carbon-in-leach (CIL) over direct cyanide leaching and carbon-in-pulp (CIP) for treatment of these ores. The laboratory program identified several factors which would enhance overall gold recoveries where preg-robbing ore was being processed, including: keeping preg-robbing ore separate from non-graphitic ore; maximising gravity recovery; and ensuring the plant operates in æpureÆ CIL mode, ie no leaching prior to first adsorption tank. Several plant trials were undertaken to assess the economic sustainability of treating moderate preg-robbing ores through a modified gravity/leach/adsorption circuit. Results indicated that where good operational control of the circuit was maintained to ensure high gravity recovery, minimal leaching prior to carbon contact, and maintenance of good, active carbon inventory, then acceptable and sustainable overall gold recoveries could be obtained. Using these relatively simple plant modifications potentially allows a plant to treat ores with preg-robbing index (PRI) values up to one. When PRI values rise to 1.3 - 1.6, leach recoveries can drop from >85 per cent to

Jan 1, 2007

When it comes to structuring major mining contracts, the two most widely adopted formats are æmeasure and valueÆ and æcost-plusÆ. A problem with both of these formats is the difficultly of aligning the objectives of the mining company with those of the contractor to achieve mutually beneficial outcomes. An alternative contractual arrangement is for the mining company to enter into an Alliance arrangement with the contractor, linking remuneration to mine performance across a range of targets. These targets can change over time as operational requirements change. &nbsp; The aims of this paper are to: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; outline alternative types of mining contracts, as well as their strengths and pitfalls; +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; describe the philosophy behind the Alliance contract at Newmont Waihi GoldÆs Favona underground mine; and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; identify some of the keys to success and pitfalls to avoid when implementing an Alliance.

Jan 1, 2007