Search Documents

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

A recovery process for rare earths (REs) such as dysprosium and neodymium from the leach liquor of permanent magnet scrap (PMS) was developed. The two hydrometallurgical routes namely liquid-liquid extraction (solvent extraction) and selective stripping were implemented. The present study deals with the separation and recovery process development by using organo-phosphorous based extractant di-(2-ethylhexyl phosphoric acid (D2EHPA) as reagent for REs processing. Initial studies considered the influence of time on the extraction process, as well as pH and extractant concentration effects. This suggested the aqueous mechanism and separation factors played a role in process during development. McCabe-Thiele diagrams for extraction isotherms were developed. Counter current extraction (CCE) using various phase ratios influenced metals separation. Maximum loading capacity of the D2EHPA was determined. The loaded organic generated by the CCE process was water washed followed by a scrubbing process to remove the other metal ion from targeted metal. Finally, a stripping process was tested using various mineral acids.

Jan 1, 2015

By Roberto Folchi, Hans Wallin

Having so many norms and technical content of legislation to deal with is a problem that an explo-sives engineer has to face, especially when working at an international level. Each country has its own norms and legislation, sometimes even each other region or state, as if the physics of explo-sions, rock, concrete, and masonry characteristics would change across the borders. Both norms and laws are frequently out of date, being mainly developed at the beginning of the previous century and adjusted, piece by piece, to a technical and political context that is constantly changing, with adjustment being frequently adopted in a hurry, due to a problem arising such as that of internation-al terrorism. Sometime also, norms are not harmonized with those they intend to amend, so required explanations and new adjustments lead to a vicious circle that increases confusion, complexity and depresses the explosive industry.

Jan 1, 2015

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By A. J. Martin, M. J. Peoples, D. J. Adams, A. Opara

"The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium (Se). Nitrogen species are also found in association with coal-mining drainages mainly due to the leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal-mining environments in British Columbia. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains.Treatment to remove Se from coal-mining waste waters has proven to be challenging for conventional water-treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry.This paper's electro-biochemical reactor (EBR) technology provides a controllable and consistent supply of useable electrons to the microbes directly at a low voltage potential (1-3 V) and low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical and robust biotreatment system. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required.Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal-mine waste waters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia’s coal-mining waste waters.IntroductionSelenium in Mining. Selenium (Se) is a naturally occurring trace element, which is an essential nutrient in small amounts (Thompson and Robinson, 1980; Brown and Arthur, 2001). However, it is also toxic to aquatic life, birds, and humans at very low concentrations. A major concern with waterborne Se is the potential for its bioaccumulation in aquatic food chains, resulting in acute and/or chronic toxicity to fish, water birds and amphibians (Besser et al., 1996; Conley et al., 2009)."

Jan 1, 2015

By K. A. Natarajan, K. Karthiga Devi

"A biodegradable flocculant was produced during growth of Bacillus megaterium. The major component of the bioflocculant was found to be a polysaccharide composed of some proteins. Fourier transform infrared (FTIR) spectra analysis revealed the presence of carboxyl and hydroxyl groups in the bioflocculant, and thermal characterization by differential scanning calorimetry (DSC) showed the transition and crystalline melting point at 90-105°C. The effects of bioflocculant dosage and pH on the flocculation of mineral suspensions were evaluated. The bioflocculant exhibited good flocculating capability on mineral suspensions and achieved flocculating efficiencies of 90 percent for kaolinite and 85 percent for hematite suspensions at a dosage of only 5 mL/L. The maximum arsenite removal was found to be 90 percent at a bioflocculant dosage of 2 g/L, which is better than traditional chemical flocculants. This study demonstrates that microbial bioflocculants have potential for application in environmental cleanup, such as in the flocculation of mineral fines and in the remediation of solutions that contain toxic heavy metals.IntroductionBioflocculants are biopolymers produced by microorganisms during their growths. The predominant components of a bioflocculant are extracellular polymeric substances such as glycoprotein, protein, cellulose and nucleic acid (Salehizadeh and Shojaosadati, 2001). Bioflocculants have gained much wider attention due to their biodegradability and safety. In recent years, the study of bioflocculants has attracted wide attention. Bioflocculants can be nontoxic, harmless and eco-friendly. Normally, they exhibit different functional properties, serving as stabilizer, dispersant or thickener. Among these properties, flocculation is of major interest. For example, Phormidium sp. strain J-1, isolated from a drainage channel, exhibited excellent flocculation activity for bentonite particles in liquid suspension (Fattom and Shilo, 1984). A protein bioflocculant produced by Rhodococcus erythropolis could efficiently flocculate suspended solids while losing their flocculating activity by enzymatic digestion (Kurane et al., 1994, Takeda et al., 1991). Klebsiella sp. strain S11 screened from activated sludge was unable to flocculate without the addition of calcium chloride (Dermlim et al., 1999)."

Jan 1, 2015

"Exploitation of an ore deposit can be optimized by adapting the beneficiation processes to the properties of individual ore blocks. This can involve switching in and out certain treatment steps, or setting their controlling parameters. Optimizing this set of decisions requires the full conditional distribution of all relevant physical parameters and chemical attributes of the feed, including concentration of value elements and abundance of penalty elements. As a first step towards adaptive processing, the mapping of adaptive decisions is explored based on the composition, in value and penalty elements, of the selective mining units.Conditional distributions at block support are derived from cokriging and geostatistical simulation of log-ratios. A one-to-one log-ratio transformation is applied to the data, followed by modelling via classical multivariate geostatistical tools, and subsequent back-transforming of predictions and simulations. Back-transformed point-support simulations can then be averaged to obtain block averages that are fed into the process chain model.The approach is illustrated with a ‘toy’ example where a fourcomponent system (a value element, two penalty elements, and some liberable material) is beneficiated through a chain of technical processes. The results show that a gain function based on full distributions outperforms the more traditional approach of using unbiased estimates."

Jan 1, 2015

By K. Huttu, A. van Wageningen

"The Kittila underground mine is extracting one of the largest known gold deposits in Europe and has an estimated mine life through 2034. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. The ore at the Kittila mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulphide minerals – arsenopyrite and arsenic-rich pyrite. The orebody consists of a complex pinch-and-swell structure including up to 100 different gold mineralization lenses. Fluctuating gold prices and other economic considerations increase the need to maintain and update the mining plans more frequently. Over 3,000 stopes need to be designed and optimized once a year for the LOM-plan and more frequent updates are needed for mid- and short term plans as well as production studies. As a large part of ore body is very sensitive to cost and gold price changes, stope optimization is crucial to find the best possible production scenario for every moment. Kittilä has gone through several methods for stope design and optimization. Most recently the Deswik Stope Optimizer (Deswik.SO) has been successfully used. Dewsik.SO has helped Kittilä to design and optimize stopes in a timely and cost efficient manner. Together with the Deswik suite of planning tools, reliable and auditable plans are created. This paper describes the methods used for stope design and optimization at Kittilä. THE KITTILÄ MINE The Kittila underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittila achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two open pits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small open pits will mine any remaining near-surface reserves in the future. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. With a mine life estimated through 2034, Kittila is Agnico’s longest-life mine. The mine’s proven and probable reserves contain 4.7 million ounces (32 million tonnes at 4.6 g/t gold). Ore has been mined from underground since 2010. The original 3,000-tonne-per-day operation underwent an expansion project to increase the throughput capacity of the mill by 1,000 tonnes/day, starting by the end of 2014. The region around the Kittila mine is underlain by mafic volcanic and sedimentary rocks of the Kittila Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle's Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between iron-rich and magnesium-rich rocks lies a 100- to 200-metre-thick structural zone known as the “Suurikuusikko Trend”. This trend hosts the Kittila deposit, where multiple mineralized zones have been traced over a strike length of more than 25 kilometres."

Jan 1, 2015

By Yun-Soo Lee, Su-Hyeon Kim, Hyoung-Wook Kim, Joon-Hyeon Cha

A7075 aluminum alloys have high strengths but poor corrosion resistance. In order to improve the corrosion resistance, a clad sheet is suggested, that is the A7075 alloy sheet bonded to A1XXX or A6XXX aluminum alloy sheets which are surface layers with good corrosion resistance. Mechanical properties of the clad sheets are determined by the combination of the component layer sheets, and thermomechanical treatment should be precisely designed when the strengthening methods of the core and the surface alloys are quite different. In the present study, three-layered A6022/A7075/A6022 clad sheets were fabricated by roll bonding process. Simplified processes incorporating a twin roll casting were also suggested in order to reduce the processing cost. Several temper methods composed of rolling, annealing, solution treatment, and aging were suggested in order to optimize the mechanical properties of the sheets. The strengths of the clad sheets were compared with the bare A7075 and bare A6022 sheets.

Jan 1, 2015

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

By H. Huang, R. N. Gow

"The reactivity of an enargite mineral electrode was investigated spectroelectrochemically under conditions typically found in alkaline sulfide leach solutions, with pH 11-13 and Na2S additions of 50 and 250 gL-1. A bulk enargite electrode was cycled between 0 and -1,000 mV for each set of solution conditions. Raman spectroscopy was used to determine and compare surface formations against species in mass-balanced EH-pH diagrams generated using STABCAL. Previously, it was determined that arsenic could be selectively leached under alkaline conditions at an average solution potential of -300mV, across the pH range 11-13. Operating under such conditions allowed for the selective leaching of arsenic with elemental sulfur formation. From several of the voltammograms obtained during this current testing, the formation of elemental sulfur appeared at increasingly reducing conditions with increasing sulfide concentration. At high concentrations, copper started to dissolve, possibly as a bisulfide complex, reducing the selectivity of the leach, unlike previous studies. However, the presence of the higher sulfide concentration is also anticipated to prevent passivation by consuming any surface formation of elemental sulfur. This study provides insight into the operating parameters of alkaline sulfide leaching in regards to the selectivity of arsenic leaching, as well as guidance for control of reagents and solution potential and, of course, the need for water treatment afterwards.IntroductionEnvironmental limitations on the pyrometallurgical processing of arsenic-bearing concentrates have forced operations to consider other solutions. Attempts to hydrometallurgically process enargite (Cu3AsS4) fall into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under basic conditions. The authors believe that the selective leaching of arsenic is more amenable because it produces a solid copper phase, preferably chalcocite (Cu2S) or covellite (CuS) that could then be processed using conventional methods already in place in the copper and gold industries. Potential leaching methods include alkaline sulfide leaching (Achimovicovica et al., 1999; Anderson and Twidwell, 2008a,b; Tongamp et al., 2009 and 2010), hypochlorite leaching (Vinals et al., 2003; Curreli et al., 2005; Mihaljovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and acid leaching (Gow et al., 2014b) with or without fine grinding to mechanically activate the enargite surface and increase normally slow leach reaction kinetics (Achimovicova et al., 1999; Balaz et al., 2000; Balaz and Achimovicova, 2006). In this study, the reactivity of enargite under alkaline sulfide leach conditions was examined."

Jan 1, 2015

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By Howard J. Haselhuhn

"The effectiveness of reagent adsorption onto hematite ore particle surfaces is critical during beneficiation to promote effective selective flocculation and dispersion and increase iron oxide recovery. The relationship between aqueous calcium in the process water and the effectiveness of common iron ore dispersants has never before been studied. The nature of common dispersants was studied in the presence and absence of calcium in the process water. The settling behavior of hematite-rich iron ore at pH 11 was assessed in the presence of calcium and inorganic dispersants: sodium silicate, sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP) and organic dispersant ethylenediamenetetraacetic acid (EDTA). It was found that inorganic dispersants are ineffective at a pH of 11 without activating the surface sites of the ore particles with calcium. Organic dispersants, however, were found to be effective with and without surface site activation.IntroductionThe United States produced 54 million metric tons of concentrated iron ore in 2011 (Jorgenson, 2013). Over 8 Mt were produced using a process known as selective flocculation and dispersion (CCI, 2011). The grade of this ore is slowly depleting, making it imperative that processing efficiency improves. To increase processing efficiency, a complete understanding of the effects of chemical reagents in the process must be acquired. This process relies heavily on dispersants to disperse iron oxides from gangue minerals in settling processes. The mechanism that these dispersants use to disperse the ore and its relationship to calcium in the process water has never been studied. The following extended abstract summarizes the relationship between aqueous calcium in process water and the effectiveness of common iron ore dispersants at dispersing hydrated hematite ore. These tests were carried out at a pH of 11, as this is a typical pH used to ensure dispersion in selective flocculation and dispersion processes."

Jan 1, 2015

By Craig M. Shillaber, Joseph E. Dove, James K. Mitchell

"This paper addresses two primary factors affecting the sustainability of Deep Mixing Methods (DMMs): construction materials and handling of the spoil from wet mixing methods. We examine these factors within a life-cycle embodied energy (EE) and carbon dioxide (CO2) emissions accounting framework, using the LPV 111 project in New Orleans, LA as a case history. The underlying assumption is that project planning and preliminary design have determined that a DMM is the best ground improvement alternative for achieving the broader aims of sustainable development. While EE and CO2 emissions are direct measurements of environmental impact alone, we illustrate how their minimization can also influence the social and economic consequences of the project. It is recommended that DMMs use lower energy and carbon material alternatives to Portland cement and lime in the binder whenever possible, with preference given to locally sourced materials. Currently available alternative cementitious materials include fly ash and slag, which are waste products from other processes. In addition, recycling the spoil material from wet mix methods on site is recommended. If the material cannot be recycled on site, transporting it to a processing and recycling center for later use as fill is preferred over landfilling. INTRODUCTIONWithin the geotechnical community there is an increased appreciation for sustainability considerations, which are an important component of the planning, design, construction, operation and maintenance of projects. An assessment of project sustainability includes holistic life cycle thinking, systems analysis, environmental impact assessment, use of safe and benign materials, awareness of local societies and cultures, social equity, protecting human health and well-being, and monetary costs (Abraham, 2006). Since ground improvement is a principal practice domain of geotechnical engineers, it is important that geo-professionals play a role in addressing the sustainability for these projects. In this paper, we illustrate by case history how different materials and methods associated with deep mixing projects can impact overall project sustainability through quantifying project embodied energy (EE) and carbon dioxide (CO2) emissions. EE is defined as all energy consumed to bring something into its present state (Chau et al., 2008; Inui et al., 2011; Soga et al., 2011; Chau et al., 2012). Recommendations are then made for how adverse environmental impacts of Deep Mixing Methods (DMMs) may be minimized, leading to more sustainable geotechnical construction."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By S. C. Gouws

"SynopsisSustainable infrastructure development has long been identified as a key enabler for socio-economic growth and poverty reduction in societies globally. Twenty-one years into the young South African democracy, economic prospects are fragile and unemployment statistics are high. According to Trading Economics (2015) the GDP growth rate in South Africa averaged 3.07% from 1993 until 2015.Through the National Development Plan 2030, the government has responded by instituting the Presidential Infrastructure Coordinating Commission (PICC) to direct national growth and drive job creation by effecting a long-term infrastructure investment programme. The Commission is mandated by Cabinet to coordinate, integrate, and accelerate implementation of more than 150 individual social and economic infrastructure plans.In the civil infrastructure development sector, increased urbanization is compelling governments and the public sector to expand safe and reliable public amenities, but the availability of real estate for construction in congested cities is a challenge. Within the mining infrastructure construction industry safe, rapid, and efficient mine extraction strategies are imperative to realize increased production, business hurdle rates, and stakeholder expectations.Asset owners and stakeholders are obliged to consider advanced mechanized underground excavation and support technologies in order to present feasible solutions timeously. From an engineering design, procurement, and construction management (EPCM) perspective tunnelling technology and boring applications have a distinct advantage over conventional excavation techniques. These solutions may enhance commerce and transportation by expanding infrastructure in concentrations of national economic activity, providing crucial linkages with rural areas, between cities, and across international borders.This paper explores the contribution by mechanized tunnelling technology and boring applications applied in conjunction with digital and automation technologies compared with conventional methodologies. The technological expertise, combined with a paradigm shift in delivery of project objectives, will promote economic growth, aid recovery from the economic downturn, and improve social development."

Jan 1, 2015

By A. E. M. Warner, P. J. Mackey

"In 1988, two of the present authors Warner and Vahed [1] were amongst several co-authors on a seminal paper reviewing nickel pyrometallurgical operations of the era. Given that significant changes in the nickel industry have occurred since that time, including the overall political landscape, technology, the overall world energy picture, the countries sourcing nickel and finally the nickel market itself, the present authors considered it timely to provide a 2015 update. In 1988, total world nickel production from sulphide and laterite sources, including production in the former "Centrally Planned Economies"- was about 0.86 million tonnes/a, while in 2014 total world nickel production reached an all-time high of almost 2 million tonnes/a - some 230% higher. On the other hand, while in 1988, about 94% of world nickel was produced pyrometallurgically and of the order of 33% via laterites, today, about 88% of nickel is by pyrometallurgy, with some 41% from laterites, thus showing that more nickel is now sourced from laterites, a trend which is expected to continue.During the period under review, new processing technologies were developed and introduced, along with substantial improvements in both the technologies employed and the scale of operations. Significant productivity gains have been achieved in sulphide pyrometallurgy in part through more efficient mineral processing, particularly in pyrrhotite rejection, and the use of ever larger-scale process equipment. This made it possible to treat lower grade and more complex ores. The significant game-changer from a production perspective was the introduction in the early 2000s of nickel pig iron (NPI) in China via modified iron blast furnace smelting, an old technology long ago cast aside by other nickel producing countries. With the exception of the emergence of this new NPI capacity in China, in the laterite industry modernization and expansion of existing operations has been employed to gain productivity, to cut costs and/or offset the effect of declining ore grades. The NPI technology development has become a game changer in the traditional global supply and demand relationship, opening up a new frontier to supply nickel to low grade utility steel producers. One other key nickel development was the Indonesian ban on nickel ore exports effective in January 2014, thus effectively curtailing NPI production at existing Chinese plants, but on the other hand, potentially prompting new smelting facilities in Indonesia. This paper reviews and updates major pyrometallurgical sulphide and laterite operations worldwide, including changes in nickel extractive metallurgy. It also provides a brief review of new developments in pyrometallurgical operations, with special focus on the NPI process and presents an outlook of the potential future direction of the industry."

Jan 1, 2015

By M. Scaggs

"Respirable dust in underground coal mines has long been associated with lung diseases, and regular dust sampling is required for assessing occupational exposures. At present, respirable dust concentration and crystalline silica content are commonly determined, but considering recent and yet unexplained increases in the incidence of lung disease amongst miners in specific geographic regions, more information about specific dust characteristics is urgently needed. While particle-level dust analysis is ideal, it is impractical for large numbers of dust samples because it is both time and cost intensive. Thermogravimetric analysis (TGA), however, is an alternative option, which offers the ability to determine the total coal to mineral mass ratio in a dust sample – analogous to proximate analysis of bulk coal samples for determining ash content. Here, preliminary development of a TGA method for this purpose is presented. The method is being developed to evaluate dust collected on mixed cellulose ester (MCE) filters using approved permissible sampling equipment. INTRODUCTION Based on the particle size, airborne mine dust can be classified in three categories: inhalable dust (< 100 µm in size), thoracic dust (< 25 µm in size), and respirable dust (< 5 µm in size) (Ramani et al., 2003). The World Health Organization (WHO, 1999) defines inhalable dust particles as those which can be breathed into the nose and mouth, and thoracic dust particles as those which can penetrate airways of the head and enter the airways of the lung. On the other hand, respirable dust particles can penetrate beyond the terminal bronchioles into the gas-exchange regions (alveoli) of the lungs (WHO, 1999). Hlavay (1992) reported that the seriousness of the damage in the lungs and respiratory tract is based on amount of dust remaining in these organs, and the amount of dust depends on the extent of dust exposure, the size distribution of the dust particles, and the capability of the body for dust elimination. Inhalation of respirable coal dust by miners can cause a disabling and potentially fatal lung disease which is called coal worker’s pneumoconiosis (CWP). Silicosis is another fatal lung disease caused by inhalation of respirable silica dust. In CWP and silicosis, dust particles deposit in the lungs, damage the lung tissue, and ultimately cause scarring which cannot be reversed (Colinet, 2010). While overall incidence occupation-related lung disease amongst coal miners in the US has been declining for over 40 years, it appears that there has been a recent increase in specific locations in Central Appalachia (CDC, 2006; Pollock et al. 2010; Suarthana et al., 2011). Although this trend is yet unexplained, one theory is that particular dust characteristics in these locations may be a factor (Hassan and Lau; Page & Oraniscak 2002). For example, several studies have indicated that different coals may generate different amounts of respirable dust (e.g., see Page, 1993 and Litton and Page, 1994), and the surrounding geology may also play a role in terms of the types of dust particles generated. Although respirable dust concentration and crystalline silica content are commonly determined as part of regulatory compliance sampling, more information about specific dust characteristics (e.g., size, shape and composition) is urgently needed."

Jan 1, 2015

By M. Jiang, X. Fan, W. X. Chen, Z. K. Guo, H. H. Zou

"Some improvements are carried out for elasto-plastic model by taking the shear dilation effects and relaxation effects of deep rocks into accounted. The high pressure equations of states with Mie-Grüneisen form are also introduced to describe the relation of pressure-volumetric strain. Numerical simulations of free field responses for deep underground explosions are conducted by using the user subroutines which compiled by means of the secondary development functions of LS-DYNA9703D codes. It is indicated that the dynamic responses of free field are well simulated based on this improved elasto-plastic model, and the analytical results are in good agreement with the data of U.S. Hardhat nuclear test.INTRODUCTIONDynamic behaviors of deep rocks for underground explosions are obviously different from that of shallow underground explosions and have aroused great attentions of international experts who work for rock engineering. The dynamic models of deep rocks could be roughly divided into classic elasto-plastic model and fracture damage model according to different theoretical foundation. M. E.Kipp and D. E.Grady et al. are the outstanding representatives who engaged in the researches of fracture damage mechanics. Researches of dynamic problems for geomaterials were carried out by C.C.Grigorian and the conclusion that incompressible elasto-plastic medium model could not be used to solve the problems of closed underground explosion was derived, and therefore C.C.Grigorian model was proposed. In this model, C.C.Grigorian assumed that the average hydrostatic pressures and the densities of medium had one to one relationship, and the path of loading or unloading is different from each other. For shear deformations, analytical solutions of the problems were derived according to the model which was slightly different from Prandtl-Reuss model, the constitutive equations were closed by Mises-Schleiher constitutive model. However, the analysis showed that there were two inadequacies in C.C.Grigorian model. Firstly, the shear dilation effects of fractured medium after wave front could not be considered. Secondly, the relaxation characteristics of the rocks in fractured region were not taken into account."

Jan 1, 2015

By M. Gagné, F. E. Goodwin

The mining industry represents a significant investment in infrastructure of which steel plays a key role. Many structures in a mine are made of steel including shaft structures (buntons, station steelwork and headgear); stope structures (roof supports, pipe hangers); haulageway structures (ore transfer stations, electrical stubbies); and surface structures (plant buildings, tank supports, pipe gantries, conveyor belts, stacks, stockpile structures, stairways and railings). Maintenance of structural components can often be difficult because of the environment, including those where corrosive fumes persist, or limited access, such as in shafts where access is limited, or to short maintenance shifts or where limited working space is available. Thus a cost-efficient, long-lasting and maintenance-free protection system for steel should be specified. Galvanizing provides the required high-quality, long-term corrosion protection to steel. Galvanizing provides protection in two ways, first as a physical barrier to corrosion and secondly by means of cathodic or sacrificial protection that is unique to zinc. The dual nature of corrosion protection provided by galvanizing significantly extends the service life of steel even in the most challenging environments. The unique corrosion protection properties provided by galvanized steel will be highlighted with global mining application case studies.

Jan 1, 2015