Search Documents

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Marcos Aurélio S. Costa, Nilton F. Nagem, Andreia B. Henriques, Herman S. Mansur, Alexandra A. P. Mansur, Antonio E. C. Peres, Valeria G. Silva

The superfine material generated in the Bayer process was used in one innovatively way as a precursor to geopolymerization techniques because of the presence of Gibbsite. Gibbsite can play a role in system adjustment because of the SiO2/Al2O3 ratio. Furthermore in the geopolymeric system it was studied the influenceof the additives such as kaolin, metakaolin and sodium trisilicate in an alkaline media. Others conditions to form the geopolymer were also evaluated such as solid/liquid ratio, SiO2/Al2O3 ratio and total alkaline. The raw materials and geopolymeric products were characterized by several techniques e.g. XRD, DSC, FTIR and SEM. Through the FTIR technique it was observed an increase in intensity and bandwidth in the region centered at 1010 cm-1, which is related to the asymmetric vibration Si(Al)-O, this is an indicating of the possible geopolymer formation This broadening of the band promotes a relative disappearance (overlapping) peaks at 965 and 935 cm-1 associated with raw material (ESPDust).

Jan 1, 2015

By Chunyang Guan, Jilai Xue, Zengjie Wang, Qiaochu Liu

Molten salts electrolysis method to prepare Al-RE alloys has attracted increasing attention recently. CaCl2 and Na3AlF6 were the most often used melts for this purpose. In this work, Al-Sc alloys prepared by electrolytic deposition process in both CaCl2 and Na3AlF6 melts were investigated, respectively. It was found that Sc distributes almost uniformly and Sc contents increase with increasing current intensity in both melts. Current efficiency was measured for comparison among various current densities applied. The alloy products were analyzed using XRD and SEM, where the formation behaviors of Al-Sc intermetallics were investigated in details. The experimental and theoretical results demonstrate that Al3Sc and Al0.968Sc0.032 are the major precipitates in the Al-Sc alloys prepared by molten electrolysis. The results are useful for selection and optimization of the molten salts compositions and the parameters of electrolysis operation.

Jan 1, 2015

By R. Padilla, M. C. Ruiz

Arsenic, antimony and bismuth are commonly found in copper concentrates usually as the minerals enargite, stibnite and bismuthinite, respectively. Concentrates having high levels of arsenic and antimony must be pretreated before smelting. Roasting is the preferred method for removing these toxic impurities from concentrates; However, the removal of As, Sb and Bi in oxidizing roasting by volatilization may not be complete due to the slow reaction rates at 500- 700 °C. Oxidizing/volatilization data were obtained from pure mineral mixtures and from arsenic rich copper concentrate. The reaction mechanism for the volatilization of arsenic and antimony were discussed. Near 100% As and over 95% Sb volatilized in the oxidation of a mixture of pure minerals at 700 °C, 1% oxygen, while over 95% As, and 35% Sb volatilized at 600 °C in 1% oxygen atmosphere when using a copper concentrate containing 3.51% As, 0.14% Sb, and 0.01% Bi. Bismuth did not volatilize.

Jan 1, 2015

By Zhenyang Wang, Yiran LIU, Xiangdong Xing, Jianliang Zhang, Zhengjian Liu

Basic characteristics of marine placer were systematically studied by chemical analyze, scanning electron microscope and X-ray diffraction in this paper. It could be found that the marine placer mainly consists of titanomagnetite and titanohematite. A series of experiments were performed to investigate reduction-magnetic separation for Fe and Ti from the marine placer. Effects of reduction temperature, reduction time, carbon ratio, magnetic density, and grinding fineness on the reduction-magnetic separation process were investigated. And the optimal process parameters were obtained as follows: the reduction temperature 1300, the reduction time 30 min, the carbon ratio 1.1, the magnetic density 50mT, and the grinding fineness of 0.074μm 86.34%. Under such conditions, the metallization rate, iron grade of magnetic substance and iron recovery reached to 94.23%, 97.19% and 90.28% respectively, and the titanium grade in non-magnetic substance and recovery of was 57.94% and 87.22% respectively. The effective separation of iron and titanium could be achieved in reduction-magnetic separation process.

Jan 1, 2015

By Shengli Wu, Jinming Zhu, Wei Huang, Xinliang Liu

The sinter of high basicity would interact with lump ores or acid pellets in the cohesive zone of blast furnace due to the difference of chemical composition and micro structures. The results of this work showed that the softening-melting properties of lump ores and acid pellet would be obviously improved by the high temperature interaction. However, the high temperature interaction index (INI) would be influenced by many factors, such as chemical composition, porosity, interaction interface and so on. The INI between sinter and porous limonite lump ore (L-2) was much higher than that of dense hematite lump ore (L-1) and acid pellet (P-1). In addition, though the softening and melting properties of L-2 were poorest in respective iron ores, the softening and melting properties of integrated burden B (consist of sinter and L-2) were not worse than other integrated burdens due to the strong high temperature interaction.

Jan 1, 2015

By Martin Reyes, Juan Hernández, Julio Cesar Juárez, Isauro Rivera, Ma. de los Ángeles Hernández, Francisco Patiño

The dissolution of Ag contained in metallurgical tailings was studied by adding ions Cu2+ and Zn2+ in S2O3 2- medium. Chemical analysis of mine tailings by cupellation revealed a Ag concentration of 71 g/ton. The XRF and XRD analysis confirmed the preponderance of SiO2 in the mineral matrix. The experimental dissolution process was conducted in alkaline solution using six concentrations of NaOH and five of S2O3 2-, at different temperatures, also using five concentrations of Cu2+ and Zn2+ as a catalyst. The results showed similar values for both systems (96.8% and 97.13%). The ion Cu2+ and Zn2+ increases the dissolution of Ag, and decrease the reaction time of dissolution. Under the conditions used, pH and stirring rate did not affect the dissolution of Ag.

Jan 1, 2015

By Messias dos Santos Machado, Renato B. Godoy, Roberta Lima, Andressa Silva, Francisco Valenzuela-Díaz, Rene R. Oliveira, Esperidiana Moura

This work aims to incorporate the Bof White Clay, from Boa Vista, Paraiba State, Brazil, as natural nanofiller in Ehylene vinyl alcohol copolymer (EVOH) and obtain flexible films. Nanocomposite was obtained using a twin-screw extruder, and film formed using a blow extruder machine. The flexible film nanocomposite was characterized, by tensile tests, XRD, DSC and their properties were evaluated. The results showed a good interaction between the clay and the EVOH resulting in an increase of properties of films nanocomposites as compared to films neat polymer.

Jan 1, 2015

By Run-sheng xu, Hai-yang WANG, Di ZHAO, Teng-fei SONG, Jian-Liang Zhang

This paper was mainly focused on the different semi-cokes and charcoal which could be new fuels for blast furnace injection. Through the comparative study with bituminous coal and anthracite coal, the properties of semi-cokes and charcoal were presented in this research. 10 indexes of different fuels were obtained by different standard experiment, including proximate analysis, ultimate analysis, igniting point, explosivity, transportation characteristic, ash properties, grindability, calorific value, combustibility and reactivity with CO2. According to the data analysis, it provided a theoretical basis for rational utilization of various blast furnace fuels, and helped to broaden the scope of the blast furnace injection fuels. This research could contribute to energy conservation, emissions reduction, and sustainable development of iron and steel enterprises.

Jan 1, 2015

By Frederico Muylaert Margem, Giulio Rodrigues Altoé, Glenio Daniel, Pedro Amoy Netto, Sergio Neves Monteiro, Maria Carolina Andrade Teles

The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. Fique fiber extracted from fique plant, presents some significant characteristic, but until now only few studies on fique fiber were performed. This work aims to make the analysis of the tensile strength of polyester composites reinforced with fique fibers. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. After fracture the specimens were analyzed by a SEM (scanning electron microscope).

Jan 1, 2015

By Cheng Yan, Yugang Li, Qian Wang, Lizhi Zhang

In continuous casting process, mold powder has lots of metallurgical effects, such as covering the molten steel to prevent liquid steel from oxidation by air, preserving heat for top layer liquid steel, lubricating initial shell and so on. However, mold powder also can deteriorate the quality of final products obviously after the entrapment of mold powder in steel. In the present work, based on the similarity theory the effect of technological parameters on mold powder entrainment was investigated by water model. Experiment was carried out in the water mold using oil and water to simulate slag and steel, respectively. The results showed that increasing casting speed increased the water-oil interfacial fluctuation and entrainment frequency; viscosity of oil also had a great impact on the interface fluctuation and entrainment; water-oil interfacial tension effect the entrainment while not changing the interfacial fluctuation; submergence depth had little impact on entrainment and interfacial fluctuation.

Jan 1, 2015

By Bingyi Bai, Lifeng Yang, Yanling Guo, Jieyu Zhang, Guoding Gao

In terms of special resources with iron, niobium and rare earth coexisting in Baiyuneboite, the new smelting technology of ferrocolumbite was studied. Reduction experients for the Baiyuneboite and explores ore phase change of Baiyuneboite in the process of reduction was conducted with graphitic carbon as the main reducer and a temperature below 1000 ℃. Moreover, it studies the influence of reducer, roasting temperature and grind fineness on the reduction as well as focuses on the evolution course of iron phase. Through the analysis on in-situ XRD of the raw ore and carbon addition ore, it also develops microstructure change rules of Fe ore phase and ore phase of paragenetic elements for composite ore(Ca, Si, Nb, F) in the process of reduction roasting. In addition, the impacts of temperature on the reduction process are also discussed. With regard to minerals of different particle sizes, the thesis will explore their ore phase changes and microstructures after 10 hours’ reduction under 900 ℃.

Jan 1, 2015

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By Guangshi Li, Xionggang Lu, Xueliang Xie, Xingli Zou, Yuyang Bian, Hongwei Cheng, Kai Zheng, Changyuan Lu

The corrosion resistance and corroded microstructure of MgO-C refractory in molten slag are investigated by immersion test in muffle furnace at 1600 °C . The microstructure and chemical compositions of the specimens after erosion experiment are characterized by scanning electron microscope (SEM) and energy dispersive X-ray (EDX). The results confirm that the oxidation of graphite is the most important degradation mode of MgO-C refractory. The structure of the refractory material is damaged due to the decrease of graphite, as a result, the periclase substrate reacts with the molten slag directly. The corrosion process is controlled by the dissolution of the refractory materials into slag, low melting point oxides are therefore generated which lead to the damage of MgO-C refractory finally.

Jan 1, 2015

By Markus Aspiala, Fiseha Tesfaye, Pekka Taskinen

In this paper, the standard thermodynamic properties of Ag3Sb and Ag6Sb intermetallic compounds have been studied by the solid state EMF-method, using Ag+ ion conducting β- alumina and AgI. The intermetallic compounds were synthesized from pure substances in evacuated silica ampoules and their formation were confirmed by the SEM-EDS analyses. The EMF measurements were made on electrochemical cells of the type [Ag | β-alumina | Ag-Sb] and [Ag | AgI | Ag-Sb]. The usage of β-alumina electrolyte, in this study, enabled thermodynamic measurements of the Ag-Sb-intermetallic compounds above 710 K, hitherto unreported. Based on the new experimental data, thermodynamic properties of the Ag-Sb-intermetallic compounds have been determined. The obtained experimental values have been compared with the available literature data.

Jan 1, 2015

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By Peng Lv, Shiqian Liu, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

The treatment process of a low-grade refractory gold ore containing sulfide minerals and carbonaceous matters was studied in this work. The gold extraction of this ore by all-sliming cyanidation was only 11.75%. Hence, a pretreatment was necessary. In this paper, a flotation-preoxidation-cyanide leaching process was developed. The concentrate from the flotation procedure was processed using different preoxidation methods. A concentrate containing 34.08g/t of gold with the gold recovery ratio of 81.20% was obtained by flotation. After roasting, microwave heating or alkaline pressure oxidation, the gold cyanidation ratio reached 82.37%, 81.26% and 71.09% respectively. Roasting was an effective, reliable and mature technique to oxidize sulfide minerals and carbonaceous matters. Roasting and microwave heating both produced dangerous environmental pollutants while alkaline pressure oxidation was eco-friendly.

Jan 1, 2015

By Dengfu Chen, Huabiao Chen, Yunwei Huang, Mujun Long, Youguang Ma, Lintao Gui

In the current work, a three-dimensional model coupling turbulent flow, heat and solute transport was developed to investigate the solute transport and redistribution in the mold of slab continuous casting where the Reynolds number is very high and the molten steel flows strongly. The conservation equations of momentum, energy and species for a multicomponent system which includes solute element C, Si, Mn, P, S were solved with the commercial software ANSYS Fluent. The parameters used in the model are based on the actual continuous casting. The fluid flow, temperature distribution and solute elements distribution were analyzed. Results showed that negative segregation occurred near the strand surface, and the species concentration reached a peak value at the solidification front during solidification. The segregation degree of solute element S is higher than the other solute elements because of its lower equilibrium partition coefficient. The species concentration in the liquid pool is homogeneous because of the turbulent flow effect.

Jan 1, 2015

By Shadia J. Ikhmayies

CdSxTe1-x and CdS1-yTey solid solutions are usually formed in the interfacial region in the CdS/CdT thin film solar cells during the deposition of the CdTe layer and/or the processing steps of the device. It is well known that CdCl2 heat treatment encourages the formation of the CdSxTe1-x alloy which improves the solar cell performance. In this work, indium doped CdS1- yTey thin films are produced by first producing CdS:In thin films by the spray pyrolysis (SP) technique on glass substrates, then annealing the films in nitrogen atmosphere in the presence of elemental tellurium. The films are characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and transmittance measurements. The transmittance is used to deduce the optical parameters such as; the extinction coefficient, refractive index, besides to the real and imaginary parts of the dielectric constant. The dispersion parameters such as Eo (single-oscillator energy) and Ed (dispersive energy) of the deposited films are also estimated and discussed.

Jan 1, 2015

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015