Search Documents

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014

By D. Seneviratne

Iron transfer from the pregnant leach solution (PLS) to the electrolyte can have a major economic impact on solvent extraction (SX) operations. High iron transfer will lead to greater operational costs, due to increased reagent consumption through electrolyte bleed and make up, or increased power costs due to decreased electrowinning current efficiency. Bioleaching of low-grade copper sulfide ore from the Kennecott Utah Copper Mine was investigated in a large scale piloting program including SX and electrowinning. Plant data and lab test work conducted throughout the course of operation, show that the unique containing PLS high ferric iron with high pH can lead to lower Cu: Fe selectivity than is typically seen in traditional copper SX operations. The impact of high ferric iron on the plant operation, and methods to reduce iron transfer will be discussed. Special considerations need to be taken for plant operating conditions and selection of SX reagents (including both extractant and aromatic content of diluent) based on the feed PLS characteristics.

Feb 23, 2014

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

By C. St. J. Lowe

Weir Minerals ? Linatex has developed a new approach to the dewatering of fine solids, particularly mine and process plant tailings and wastes. The Weir process, patented in 2009, uses standard process equipment in a standard flow sheet, but applies this approach to materials previously thought to be too fine to be dewatered with this type of equipment. The process can be applied to a wide range of materials, making lower moisture products that can be re-used elsewhere or sent to disposal. It has already been tested successfully on a small scale in Australia on coal fines, zinc mine tailings, red mud, iron ore tails, and copper/gold tailings. The principal factors affecting the solids recovery have been established as: 1. The % solids in the slurry feed to the process ? a higher % solids provides a higher recovery. 2. The particle size of the feed solids ? coarser feeds provide higher recoveries. The key factors affecting the % solids in the dewatered product have been determined to be: 1. The particle size of the dewatered product - coarser materials produce a higher % solids in the dewatered product. 2. The height of the discharge weir on the dewatering screen - a higher discharge weir on the dewatering screen also yields a higher % solids. 3. The angle of the dewatering screen. Setting the screen horizontal increases the travel rate, reduces the bed depth and reduces the % solids in the dewatered product. Back-sloping the screen up to 5° reduces the travel rate and increases the % solids in product. Eight plants ranging in size from 3 t/h to 40 t/h have been sold to a range of customers in China, for coal and iron ore tailings treatment. Australia has one plant, a small unit rated at 30 t/h of sand fines, and has recently completed test work on iron ore tailings for a dewatering plant rated at 135 t/h. Additional tests are under way with clients around Australia, to demonstrate the capabilities of this process on specific applications and to provide confirmation that materials can be processed successfully, before moving on to larger scale tests or full size plants. The advantages of the Weir process include - lower moisture in products, uses proven equipment, lower capital and operating costs, lower maintenance costs, reduced power consumption, compact footprint, can be used in parallel or in series with existing equipment, modular design to facilitate redundancy or expansion, efficient water recovery and simpler water management, reduced cement in backfill mixes, smaller tailings disposal footprint, reduced earthworks requirements, much lower seepage losses, more stable tailings mass, progressive site rehabilitation, reduced impact on local wildlife, reduced risk of dam wall failure, and reduced environmental monitoring and compliance costs.

Feb 23, 2014

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By L. K. Holder

The White King / Lucky Lass Superfund site consists of two former uranium mines in south-central Oregon. The remedy included consolidating two large mining overburden stockpiles that contained low levels of radioactivity and heavy metals by moving over 700,000 cubic yards of material and then capping the combined stockpile. An innovative armored cap design was used to minimize the stockpile footprint and thereby prevent disturbing existing wetlands. In addition, the stockpile was designed to merge into the surrounding topography. The remedy also included stream restoration and development of new wetlands. The stream was returned to its pre-mining channel, with the addition of hydraulic features to create new wetlands. The wetlands have greatly enhanced the ecological value of the remedy and the site.

Feb 23, 2014

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By C. Bazin

The fundamental error associated to the sampling of heterogeneous ore particles is unavoidable and can only be minimized by an adequate selection of the sample mass and/or size reduction of the sample before division into sub samples for testing or assaying. The preparation of ore batches to carry out the mineral processing evaluation of an ore is a sampling process. The fundamental error associated with the division of the ore into batches is responsible for the differences in the composition of the batches. This paper attempts by various means to assess the reproducibility of the gold content of test batches prepared from a gold ore sample. The results of the investigation shows that for fine gold grain sizes the variability in the composition of the batches is less than that predicted by Gy?s formula and that the gold grain size is a strategic information in the assessment of the gold content variability of test batches.

Feb 23, 2014

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By J. A. Botín

Investment decision for large mining projects imply an enormous financial risk and therefore, require a more complex risk evaluation methodology taking into account all sources of uncertainty from each process in the project value chain. Generally, the main sources of risk are those related to uncertainty on grade and other techical variables of the orebody. In this study, conditional simulation is applied to develop a risk management model to quantify and to manage financial risk associated to uncertainty on the grade of the orebody. The model was validated in case study on a real porphyry copper orebody in Chile.

Feb 23, 2014

By A. Janwong

Ion exchange technology is becoming more prevalent for metal recovery from low concentration solutions. The products of ion exchange are typically a metal free stream (product stream) and a concentrated metal stream (byproduct). The metals in the concentrate stream are usually precipitated and returned to the process or discarded. The unique features of emew® technology enable metals to be recovered directly from the concentrated stream. The advantage of the IX-emew® combination is the ability to have two product streams: 1) clean metal free solution and 2) metal product for sale. In addition to recovering metals from solution, it is also possible to separate metals from each other and recover more than one metal product. In this paper, examples of IX-emew® combinations are detailed including the recovery of copper, nickel and cobalt from an industrial waste stream, recovery of nickel from a spent electroless nickel plating solution and recovery of cobalt from an hydroxide cake.

Feb 23, 2014

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By J. Brune

The disaster at the Upper Big Branch (UBB) mine 2010 has demonstrated the destructive violence of a coal dust explosion by killing 29 miners in the worst mining accident the United States has experienced in almost 40 years. This explosion brought to light that the United States mining industry must strengthen explosion prevention and explosion hazard detection practices. Recent legislation such as the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) pushed the strengthening of explosion and disaster response and miner protection in addition to stricter regulations on the sealing of abandoned areas and on conveyor belt flame resistance. The focus of this new act was on how to respond to a disaster or explosion, yet not much improvement was made with respect to prevention explosion disasters. Researchers at the Colorado School of Mines have recently concluded extensive research into methane and coal dust explosion prevention practices and regulations as it may be applicable to underground mines in the United States. This research aims to forward more studies into the use and adoption of standards and procedures that have been utilized in countries with strong explosion prevention histories.

Feb 23, 2014

By J. `. Spitzinger

In situ recovery (ISR) of uranium alters the baseline groundwater geochemistry in order to mobilize and complex uranium to extract and concentrate it. ISR wellfield restoration is often challenging, and primarily relies on groundwater sweep, reinjection of treated permeate, and/or injection of reductants. Greater focus should be placed on injection-based approaches (using existing infrastructure) based on established engineering concepts used for in situ remediation of groundwater plumes. Such injection-based approaches could shorten restoration timeframes consequently reducing long-term operational costs. This paper addresses various types of injection-based approaches to wellfield restoration based on in-situ remediation success with other constituents that require similar treatment. This paper describes necessary design practices for injecting reactive chemicals (e.g., reductants or biostimulants), operations and maintenance (O&M) strategies to prevent fouling of the chemical delivery system and well network, and natural constraints to restoration. Best practices for successful biostimulation strategies that minimize residual uranium, radium, oxoanions, and other trace elements are as described. Advantages of such injection-based approaches could include significant reductions in restoration times, and consequently, lower restoration costs.

Feb 23, 2014

By R. E. Vivas

Goldcorp is one of the largest gold producers in the world with projects in South, Central and North America. Goldcorp?s flagship operation is Peñasquito, a world-class, poly-metallic deposit that started production in 2010 which is one of the largest mines in Mexico. Since the early stages of the project, Goldcorp has used the most advanced technologies available to maximize its value. However, the implementation of optimum mine plans has been challenging to put into practice. This is due to the fact that the mine operation involves more complexity than the plans usually reflect. This challenge is an industry wide issue that presents opportunities for improvement. This technical session discusses the mine planning methodologies and procedures used to connect long, medium and short term planning strategies in order to bridge the gap and produce optimum mine plans that can be practically implemented in the field.

Feb 23, 2014

By M. S. Safarzadeh

Cu-As feedstocks are among the most problematic copper sources that have been avoided over the past years. The high arsenic content of such ores/concentrates combined with their refractory nature have directed the metallurgical industry towards developing efficient technologies for the treatment of high-arsenic copper ores/concentrates. As the most important member of Cu-As-S mineral system, enargite (Cu3AsS4) is frequently encountered in some of the important copper deposits. Several hydrometallurgical and pyrometallurgical processes have been examined for the treatment of enargite concentrates, but currently, no commercial operation exists. In an effort to develop an original processing option, an acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2?4H2O, PbSO4 and Cu0.47Fe0.53SO4?H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 h with a sulfuric acid to concentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena, and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different levels. The purpose of this paper is to evaluate phase transformations during the acid bake-leach process for the treatment of an enargite concentrate, and to study the effect of sulfuric acid dosage on the extraction of Cu, Fe, and As. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.

Feb 23, 2014