Search Documents

By D. Spitty

There are enormous complexities with mine planning and the problem itself presents a huge challenge to the existing mine planners performing this activity. Mine planning optimization supports planners to determine ?What are the best increment excavation sequence and the best material blending combination such that throughput, quality, cost, utilization and Net Present Value (NPV) targets are met?? It is achieved through using an advanced scientific approach that has been specifically adapted to address the mine planning dilemma.

Feb 23, 2014

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By L. Sandbak

The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestones, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods. TRJV has been working to optimize ground support and mechanize top cut drift sizes and eliminate operating hazards associated with jackleg drilling. Safety Factor analysis based on bolt strengths has allowed us to pursue larger sized top cut drifts and to evaluate bolt length sizes and spacing. Switching from jackleg sized drifts of 10?W x 10?H to a mechanized 12?H x12?W top cut drift design has the potential to decrease overbreak, provide more uniform drift design sizes and bolt patterns, and increase ore production by at least 38%.

Feb 23, 2014

By R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic solutions, over the pH range 1-7, to determine a potential range for co-dissolution.. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated predominance diagrams for the copper-arsenic-sulfur system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Feb 23, 2014

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By J. V. Belke

There are many aspects of a grinding mill supply and installation that can result in the mill not operating as intended, resulting in unplanned shutdowns, poor reliability and headaches for all concerned. One of the largest aspects, both in criticality and physical mass, is the mill foundation; if not properly specified, designed and constructed the mill operation will be compromised. The mill foundation starts with the design specification and loading diagram supplied by the mill builder. The importance of understanding these documents and how to apply them is critical for the start of any mill project. When designing mills with a GMD the foundation must be properly modeled to ensure that all interactions of the mill and motor structures, foundation and subsurface strata behave in the intended fashion. All of the previous efforts can be laid to waste if the construction of the mill foundation is poorly handled. Mill foundations are typically the most massive concrete structure at a processing plant and can easily cause nightmares for inexperienced contactors. This paper explores some of the more important facets along the lifecycle of the grinding mill foundation.

Feb 23, 2014

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By K. Zhang

Real option value (ROV) method is considered to be more practical and advanced compared to net present value (NPV) method in evaluating a mining project, in particularly when there is substantial uncertainty in the commodity market as well as possible operational flexibility embedded in the project. Usually, it may take months or even years for the commodity product to be available in the market after the mining activation decision is made. The impacts of postponing the delivery of commodity product on the mine?s ROV and NPV are assessed based on the proposed real option method. Postponing the delivery of the products leads to declined NPV and ROV compared to the non-postponing scenario and extended postpone results in higher lost values in NPV and ROV. For a mine with lower mining cost, by postponing the delivery, the exercising threshold of commodity price is lower because the mine owner anticipates that commodity price may rise during the time of postponing. A mine with higher mining cost requires a higher exercising price threshold to ?lock up? the profit when there is ambiguity of market situation due to the postponing of the delivery.

Feb 23, 2014

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By F. Mielli

Over the last three years there has been an increase in mining congress and conferences focusing on water management. Water in mining is a key concern for mine managers and operations, and we are now seeing this operational dilemma escalated to the level it deserves. According to Frost & Sullivan research, mining water and wastewater treatment and its related technologies will be a U$3.6 Billion global market in 2016, which translates the importance of this issue. Looking at the current mining trends, some factors increased the importance of water in mining operations, including: ? Future mining investments will be located in geographical locations where water is scarce (water stressed areas) ? A decline in grade will increase the intensity of mineral processes and therefore increase the use of the water ? Increased sustainability and regulations will extend the control/monitoring of water during the entire mine life cycle representation of the mine water flow system. A water balance has several benefits/objectives in a mine operation: ? Mine planning/simulation of mining scenarios/climate change Production optimization ? Minimizing strategic and operational risks ? Social license to operate ? Water-smart mine planning ? Target: water neutral mines ? Benchmarking within and between sites ? Sharing knowledge/technology transfer ? Reporting/communications ? Permitting/Compliance

Feb 23, 2014

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By A. Anani

The goal of hot mix asphalt (HMA) design is optimal material blending to meet Superpave specifications. HMA cost minimization has being modeled as linear programing (LP) (Awuah-Offei et al 2011) and mixed integer LP problems (Brown et al, 2012) and solved with commercial software such as LINDO and CPLEX. Often these software, which are designed to solve general optimization problems, have licenses that cost thousands of dollars. The objective of this study is to develop a novel solution algorithm to the HMA optimization problem presented by Brown et al. (2012), which will negate the need for expensive commercial packages and is specific to this problem. This novel algorithm is based on the branch and bound algorithm for solving mixed integer problems. The algorithm is incorporated into a software package with an easy-to-use graphical user interface. The developed algorithm is validated using a real-life HMA problem. Using this solution algorithm will save companies thousands of dollars, otherwise used to purchase software licenses.

Feb 23, 2014

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By S. Philipp

This paper describes several variants of placement and design, from a technical and economic point of view, of shafts, ore bunkers and drifts near shafts of a Russian potash mine. Advantages and disadvantages of the position of different workings are shown as well as an analysis of stratigraphic and geological layers and their use for excavating pit bottoms, haulage drifts and bunker installations. The potash mine consists of two hoisting shafts and one service shaft. The hoisting capacity of one of these skip shafts is planned to be approx. 7 Million tons of crude potash salt per year. Both shafts together will have a hoisting volume of about 14 Million tons. When the mine will increase their highest level of production, it will be one of the biggest potash mines in the world. The skips, the hoist drives and the bunker near the shaft will belong to the largest ones worldwide, too. This paper specifies the features of such a double skip shaft pit in detail and demonstrates problems, which depend on the fact that the pit bottom is in a depth of nearly 1200 m.

Feb 23, 2014

By J. A. Mejia

The combination of high-resolution X-ray microtomography (HRXMT) image analysis and Lattice-Boltzmann Method (LBM) simulations has demonstrated the ability to describe real multiphase flow problems in fine coal filtration. The single component multiphase flow He-Chen-Zhang LBM model was used to simulate filtration with actual HRXMT images of pore network structures produced in filtration experiments. The analysis performed on coal, silica, and glass bead filter cakes showed that particle shape and wettability are two of the most important factors in the retention of moisture during filtration.

Feb 23, 2014

The impact of a methane explosion on mining operations cannot be over-emphasized. The explosion is a result of rapid combustion when a methane/air mixture is ignited by an unexpected energy release, such as a mine fire, electrical arc or sparks caused by frictions or rock falls. In most cases, an ignition of methane/air mixture could result in a deflagration other than detonation. Resulting flames and overpressure induced by a methane deflagration will harm neighboring miners and local ventilation control devices.. ,It is essential that the mechanism of an explosion and associated destructiveness be fully understood. This research seeks to predict an influence region of an incident happened within a representative underground mine geometry. The most common geometric changes in an underground coal mine are bends, regulators/doors, obstacle in airways and changes in sectional area. These geometric changes could result in an attenuation of the flame and pressure wave as a result of a methane deflagration. A study of this phenomenon could enable mine planners to have better understanding of the over-pressure redistribution due to the explosion. Both numerical and experimental work has been done in this study to ascertain a better insight of this potentially devastating event. The experimental data are also used to validate the turbulence and combustion models used in this test.

Feb 23, 2014

By E. Hsieh

Proximity detection in the open pit mine can be used effectively as an operator assist strategy which improves digging production through enforcement of best practices, although it is normally thought of first as a safety tool, and second as a step toward full automation when combined with object avoidance.

Feb 23, 2014

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By T. W. Camm

Some of the defining characteristics of narcissists include a grandiose sense of self-importance, preoccupation with success and power, a sense of infallibility, and a supreme confidence in their ability and intelligence. Ironically, many of these characteristics are rewarded in business organizations, which may explain why there seems to be so many narcissists in management positions. Assuming we will be dealing with narcissists throughout our career, it makes sense for us to understand what makes them tick, and more importantly what we can do to work with them in a constructive manner.

Feb 23, 2014

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014