Search Documents

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

By Rusty Winn

"R.E. Janes Gravel Co. is an aggregates producer is located along a paleo-channel of the Ogallala formation (locally known as the Slaton Channel) approximately 48.3 km (30 miles) southeast of Lubbock, TX. In an attempt to beneficiate the 25.4-mm (1-in.) concrete aggregate product, a log washer was installed in the processing line to liberate and remove fines (clay) from the finished product. The introduction of this extra cleaning step increased fines in the finished product, exacerbating the original problem. Several other processing options were investigated before a geological analysis was undertaken to try and define the lithology of the formation and formation characteristics in an attempt to alleviate this problem.Initial assessmentsThe mined resources are mid-Miocene to early Pliocene (16-4 mya) in age and is the eastern exposure of the Ogallala formation of the Southern High Plains escarpment. The Ogallala formation consists of coarse-grained alluvial sediments in paleovalley channel ways from the Rocky Mountains with fine Aeolian and paleosol deposition on the uplands across the High Plains region of the United States. Locally, these Rocky Mountain sediments from New Mexico were transported and deposited in a paleochannel that is approximately 0.805 km (0.5 miles) wide and 15.25 to 18.3 m (50 to 60 ft) in depth. As this channel cut across the Southern High Plains it eroded local rock sources of Late Cretaceous limestones and Triassic sandstones and mudstones incorporating them into the younger Ogallala depositional sequence.Depositional historyThe channel currently being mined is a nontypical Ogallala deposit. The Ogallala in the panhandle of Texas is divided into two units, the Couch and the Bridwell. The Couch is the older of the two and exhibits alluvial sedimentation of thicker and larger gravel (up to 76.2 mm or 3 in.) deposits fining upward to Aeolian sedimentation and thick friable caliche deposits. The Bridwell overlies the Couch and is characterized by alluvial sedimentation, a distinctive red tint and smaller gravel components (typically no larger than 25.4 mm or 1 in.) fining upward to Aeolian sedimentation and thick, well-indurated caliche cap. The Slaton Channel divides these two units and shares lithologic components of both, yet is lithologically distinct due to its Cretaceous Age limestone gravels that can be < 3.66 m (12 ft) in size. Caliche/calcrete is a calcareous (CaCO3) deposit that forms in the B horizon of soils as a rain water leachate of CaCO3 from the upper A horizon."

Jan 1, 2014

By Zhazira Baltabekova, Nina Lokhova, Arailym Dukembayeva, Madali Naimanbayev, Zhantore Dzhurkanov

"Recycling of industrial waste provided they have enough valuable elements requires significantly less investment compared with ore processing. Promising man-made raw material of rare earth elements (REE) is phosphogypsum. Works performed on dismantlement of phosphogypsum only concern phosphogypsum processing from apatit. In this case, none of the developments was tested for phosphogypsum produced on the basis of phosphorus, chemical and mineralogical composition of which is markedly different from apatites. We studied phosphorites of the Karatau deposits (Kazakhstan). Mineralogically all the layers are composed of three main ingredients: phosphate, silica and carbonate, which account for 92-96% of the weight composition of ores and rocks. Of impurities there are pyrite, iron hydroxides, gypsum, fluorite. In addition to the actual composition of phosphate in phosphate ores there are apatite. Silica is presented by chalcedony and quartz, and carbonate by calcite and dolomite. The results of X-ray microanalysis showed point cluster of grains containing REE in samples of phosphate ore. Analysis of the grain showed that REE are in the form of phosphates and silicates, which according to numerous studies in apatites is not established. In this regard, phosphogypsum, waste of production, is different in composition too. Therefore, transfer of techniques proposed in the methods for extracting REE from phosphogypsum after processing apatite, did not give the stated results and required a new approach to solving this problem. It should be noted that the phosphogypsum produced by processing the Karatau phosphorite contains medium group of REE by 2.6, and heavy group by 7.8 times more than phosphogypsum from processing the Kola apatite. Given the shortage of medium and heavy REE research to develop ways to extract the lanthanides from phosphogypsum after processing phosphate rock is promising. The study contains results of studies on the extraction of REE from phosphogypsum after Karatau phosphorite processing."

Jan 1, 2014

By J. Bouchard, Ali Vazirizadeh, R. del Villar

"The amount of water reporting to the concentrate correlates well with the solid entrainment. It is well known that the frother and collector dosage as well as the froth depth and gas rate influence the amount of water reporting to the concentrate. This is also true for gas dispersion properties such as gas holdup and bubble surface area flux. On the other hand, a positive bias rate, required to reduce hydraulic entrainment, also affects water recovery and thus the particle recovered by entrainment (depending on the their size). Up until now, the effect of the gas rate on the water recovery has been studied, but no comprehensive investigation on the gas holdup, bubble size and bubble surface area flux has yet been reported. This research precisely aims at addressing this issue. The experimental work was carried out under a constant gas flow rate to eliminate the gas volume effect, while other gas dispersion properties have been varied by modifying the frother concentration and the shearing water introduced to the frit-and-sleeve sparger. A constant froth depth and no wash water were used, in order to be able to evaluate the exclusive correlation between the water recovery and the bubble surface area flux and/or the bubble size. It is worth mentioning, that the particle size of the hydrophobic particles did not show a significant effect on the amount of water going to the concentrate. Not surprisingly, experimental results demonstrate that water recovery increases with the bubble surface area flux and with the gas hold-up."

Jan 1, 2014

By J. B. Yianatos

A practical an interactive model to describe the operation of a flotation bank of mechanical cells was developed based on the hydrodynamic and metallurgical characterization of large industrial flotation cells. Thus, the mineral grade and recovery, as well as the stream properties along the flotation bank can be described in terms of the operating variables. The model was built considering the flotation bank as a distributed system, so the solution for the water and solids mass balances, per size classes, for each single cell, are sequentially solved. Also, each cell was described by two distinct zones, the collection zone characterized by the flotation rate constant and the froth zone characterized by the froth recovery. The mineral feed was described in terms of the mineral species and particle size classes, using a rectangular flotation rate constant distribution. Also, the effect of changing the actual operating variables (air flowrate, pulp level, pulp density, pulp flowrate, etc.) on the mineral collection process, in the collection (pulp) zone, was considered downstream along the bank. The froth recovery of floatable mineral has been estimated by measuring the mass flowrate of particles entering the froth by true flotation together with the concentrate mass flowrate (ton/h). The mass flowrate of collected particles at the pulp/froth interface level was calculated from direct measurement of bubble load (ton/m3) and gas flowrate (m3/h). Flotation recovery is mainly related to the froth depth and air flowrate. All parameters considered in the model have been adjusted from direct measurements in plant site. Also, the effects of other operating variables such as reagents dosage, top of froth grade, or froth discharge velocity are presently under study. This procedure has been tested using data from industrial rougher operations consisting of flotation banks with 5 cells to 9 cells in series, and different cell sizes, such as 45m3, 130m3, 160m3 and 250m3. Thus, it has been shown that the model approach is a powerful tool for flotation cells diagnosis, operation and development of new control strategies, as well as, to evaluate the effect that de-sign and operating variables have upon the collection and froth zones performance in large flotation cells.

Jan 1, 2014

By Carolina Achiardi, Álvaro Videla

"In pre-design a flotation plant copper sulphide is useful to apply a simplified methodology of economic analysis that relates the size of the grinding product (P80) with the throughput and their effect on copper grade and recovery of copper in the final concentrate of a flotation circuit. With this objective, this methodology covers the following analysis, perform by evaluation of five sizes grinding products (P80): 120, 150, 180, 210 and 240 microns. • Flotation testwork (rougher kinetic, open and closed cycle test) has been done to determinate the optimum operating conditions and to estimate the maximum recovery of copper in the concentrate, using Klimpell model • Flotation plant design assumes a conminution product obtained from a 25,000 HP ball mill • Metallurgical balance is performed for the circuit based on flotation testwork • Economic evaluation by calculating capital expenditure (CAPEX), operating expenditure (OPEX) and sales revenue, to determine NPV is performed and relates to the NPV. An optimum grind size is then obtained based on cash flow. The results shows a grinding product size that optimizes flotation and allows a higher NPV and INPV over other alternatives."

Jan 1, 2014

By F. Cheuk, E. Krause, V. G. Papangelakis, G. A. Moldoveanu, S. Abendschein

Systematic studies have been conducted at the University of Toronto in order to evaluate lanthanide extraction from clay minerals from different geographical regions. It was found that rare earth elements (REE) are easily recovered into an aqueous solution via an ion exchange mechanism by leaching with electrolyte solutions containing monovalent cations under ambient conditions. In this study we assessed extraction levels of individual REEs as a function of initial clay composition and leaching conditions. It was found that, in spite of variations in clay origin, all clays consistently reached peak REE extraction levels with fast kinetics. However, terminal extractions were clay-specific. The feasibility of using seawater as a leaching solution and potential synergies with ammonium sulphate as a lixiviant was also investigated. Seawater was found to be inferior to using ammonium sulphate, and provided no observable synergy in leaching performance when used together. The aqueous phase trapped in leached clays was shown to contain significant amounts of REE, as demonstrated in clay washing tests. Techniques to improve the REE concentration in leachate through process variations were investigated. However, it was found that most techniques capable of increasing REE concentrations in the resultant leachate also resulted in reduced REE extraction.

Jan 1, 2014

By Felipe Costa Hashimoto Bertin, Jorge Alberto Soares Tenório, Rodrigo de Souza Dalti Pereira, Denise Crocce Romano Espinosa

"The increasing amount of portable devices and their fast obsolescence generates an increasing quantity of discarded batteries. The recycling process of discarded batteries allows the recovery of metals for further use and avoids the contamination of soil and water. Even though there are several researches on the topic, few papers focus on mixed batteries. The purpose of this work is to characterize a mass of collected mixed batteries and study the hydrometallurgical process of recycling. The specific leaching parameters studied were pH, temperature and reduction potential. The specific goal was testing the selectivity of pH for leaching each metal. The results show that the optimal leaching occurs in acid solutions with negative pH at IM of sulfuric acid and at room temperature (25°C).IntroductionThe increasing portability of electronic devices in the past century along with their fast obsolescence produce tons of discarded materials yearly that could be recycled generating new materials for the industry. For example, metals such as cobalt and nickel, that are worth respectively US$ 30.00 and US$ 16.10 per kilogram[l,2] are disposed in urban trash yearly, which means that millions of dollars are thrown away instead of being recovered and reused[3].Besides the obvious fact that the society is throwing money away, most of these metals are toxic for the environment and all mammals, so when badly stored after use they can be found contaminating ground water which will contaminate the entire lifecycle. Some of these metals can cause cancer, serious lung problems and have bioaccumulative properties [4] resulting in lower productions of natural products and maybe death for consumers.So in compliance to new regulations such as the National Solid Residue Politic (PNRS) and the CONAMA-Resolution N°401 from November of 2008[5]- (that follows similar restrictions and regulations as the European directives) all those urban and electronic wastes need to be correctly disposed and treated before being thrown away on local dump sites.In Brazil the national rate of garbage recovery is around 70%, which only 5% is properly recycled, accordingly to the research of the UFSC, also electronic waste grows at 5% per year [6]The present study was motivated by the fact that recycling processes for batteries are not spread through the country and by the fact that most papers do not try to recycle a mixed mass of batteries, but a specific mixture which does not represent the composition of traditional household wastes."

Jan 1, 2014

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By B. Z. Wu

The flotation of low-grade zinc oxide ore which from Guizhou has been researched by sulfuration- amine method. The experimental result indicated that when pH of pulp was 11, good flotation index can be achieved by using sodium silicate as dispersant, mixed amine as collector, and the do-sage of sulfur sodium was 6kg/t, and the recovery of zinc can be heightened by using copper sulfate as activator and Hydroxamicacid as collector. When the zinc feed grade was 4.84%, the zinc concentrates with grade of 39.23 % and recoveries of 75.17 % were obtained by adopting this technics.

Jan 1, 2014

By J. Faitli

The Lake Balaton is the biggest and for many reasons the most important lake in Hungary. To preserve its healthy nature it is necessary to remove the accumulated mud time to time, similarly to the many living waters, lakes and rivers everywhere. Typical existing technologies (mechanical, hydraulic) require large depositional areas, where the removed slurry and mud is dewatered through very long time. One problem is the non existence of an economical mud thickening technology. Another major problem is that current methods remove the sand fraction with the mud as well. Many times sand has to be complemented from outer sources to endanger the natural balance of the living water. By the financial support of the NKFP 3A/068/2004 Hungarian Research Project our consortium has been looking for the solution to the above mentioned problems. The original ideas of the project were: 1. Sand should be separated and returned to the water by hydrocyclon; 2. New mud thickener should be developed based on the principle that vibrating rods can force settling and packing of mud particles. The work was started by fundamental research with different samples from Lake Balaton and River Bodrog. An automated settling column (45L) has been built for the investigation of the effect of vibrating rods on the settling behavior of suspensions. An optical sensor has been developed by with the settling curve (height of settling slurry as function of time) can be automatically measured. Different vibrating methods and parameters have been tested by the application of a linear motor and mechanical eccentric drive. On the basis of the fundamental research a new thickener, called the rod ? lamella thickener has been developed and an industrial size (50m3/h) mud removing technology has been built. Main parts of the technology are the traditional dredging barge and the thickening technology. The thickening and sand separation technology is tugged by the dredging ship. Its main elements are the homogenization tank, slurry pump, hydrocyclon and the rod ? lamella thickener. In this unit lamellas carry out pre-thickening, then vibrating rods further increase the concentration. The thickened mud is transported out by a screw - of which revolution number is precisely controlled - against a spring supported valve. Paper reports about the design, building, water probe and on-site tests of this mud removing technology. Two new patents had been presented, one is about the rod ? lamella thickener and the other is about the mud removing technology with sand separation.

Jan 1, 2014

By P. Pourghahramani

Several structural characteristics change during intensive milling such as chemical composition, phase transformation, crystallite size, lattice strain, lattice parameter (s) and solid reactivity etc. The creation of defects enhances the stored energy (enthalpy) in the solids and consequently causes a decrease of activation barrier for the process and/or subsequent processes. In this paper, the effects of milling on the structural changes of hematite have been investigated using dry millings. The structural changes have been characterized using a combination analysis of BET surface area measurements and X-ray diffraction (XRD) analysis. Besides, the hydrogen reduction behaviors and kinetics of mechanically activated samples and initial sample were studied using simultaneous thermal analysis (STA). The methods of Williamson-Hall and Warren-Averbach were used for analyzing of XRD patterns to resolve and extract the microstructural characteristics of hematite phases. It was concluded that the breakage and aggregation of particles take place mainly in the starting and prolonged stages of dry grinding, respectively. The BET surface area enlarged steadily over the grinding processes whatever milling methods were utilized. The characterization of structural changes revealed that the hematite milled under various conditions did not undergo any significant reaction or phase transformation during milling processes. In addition, X-ray amorphous phase con-tent increased gradually with extending the grinding intensity. The maximum X-ray amorphous phase exceeds about 81% after 9 hours of milling in both tumbling mill and vibratory mill. The Williamson-Hall plots revealed the anisotropic character of line broadening for deformed hematite and changes in the trend of microstructural characteristics as a function of milling time. It was found that the surface weighted crystallite size decreases and lattice strain increases over the grinding periods. The minimum surface weighted crystallites were calculated about 17.3 nm, 12.2 nm for the products of tumbling and vibratory mills respectively. The maximum lattice strain,, in the grinding with tumbling and vibratory mills was calculated about 4.44×10-3 and 3.95×10-3respectively. 21/210nmLe=<> The non-isothermal kinetic analysis of the products revealed that Fe 2O3 reduced to Fe in a two-step process via Fe3O4. Intensive grinding resulted in improved resolution of overlapping reduction events. It was also established that the mechanical activation had a positive effect on the first step of reduction. The prereduction step in the activated samples initiated and completed at lower temperatures than that in non-activated samples. The activation energy of reduction decreased at the first step of reaction with increasing the grinding intensity. Intensive milling increased slightly the average activation energy of the second step of reduction due to the present of finely agglomerated particles and intensive sintering of the particles in higher temperature ranges.

Jan 1, 2014

By E. Gock

Based on the scientific investigations on mechanochemical synthesis of metal sulphides from metals or metal compounds and sulphur or sulphur compounds, the article describes the industrial production of nanoscale metal sulphides. Special operational conditions such as inert atmosphere, size and type of the grinding balls, grinding time and specific energy input are taken into consideration. A system configuration for the manufacturing of sulphides at a capacity of 100 kg/h is presented.

Jan 1, 2014

By H. Ding

Calcium carbonate/Titanium dioxide composite, characterized by coating TiO2 on the surface of CaCO3 particles, is an important substitute for titanium dioxide. This paper studies preparation method of CaCO3/TiO2 ,composites based on mechano-chemical effects, measures its properties as a pigment, analyzes the binding form and interface reaction mechanism between CaCO3 and TiO2. Through single finely grinding of CaCO3, co-grinding of CaCO3 together with TiO2, and mecha-no-chemical effects produced in the course of grinding, CaCO3/TiO2 composites can be prepared successfully. Results indicate that grinding fineness of CaCO3, co-grinding time of CaCO3 and TiO2, the weight ratio of grinding media to mineral feeding, and the amount of TiO2 have much influence on the properties of CaCO3/TiO2 composites. CaCO3/TiO2 composites have the properties same as titanium dioxide pigment, oil adsorption and ultraviolet adsorption same as TiO2, and 90% of hiding power as that of TiO2. Wet grinding of CaCO3 causes the production of mechano-chemical effect and hydroxyl group, through which CaCO3 and TiO2 can be bonded together. Repulsion occurs between the particles of CaCO3 and the particles of TiO2, respectively, they are both in good dispersion. But attraction occurs between CaCO3 and TiO2. TiO2 particles are distributed evenly on the surface of CaCO3. Therefore, coating of TiO2 on the surface of CaCO3 particles and chemical bond between them make CaCO3/TiO2 compo-sites have pigment properties of Titanium.

Jan 1, 2014

By Winston Wilches B., Scott Scovira

This paper discusses recent changes to the emulsion blend blasting agent used at the Drummond Pribbenow Mine in Colombia, one of the world’s largest open pit coal mines, and the resulting improvements in rock breakage and excavator productivity. Based on field evaluations, the use of High Density Ammonium Nitrate (HDAN) can be effectively implemented in an emulsion blend blasting agent, yielding excellent results in terms of energy release, shelf life and velocity of detonation (VOD). Field evaluations showed that formulations using HDAN exceed the performance of the actual 50%/50% emulsion/ANFO blend using Porous Prill Ammonium Nitrate (PPAN). PPAN is conventionally used for emulsion blend manufacturing, with physical characteristics to facilitate sensitivity during the detonation process.

Jan 1, 2014

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By J. M. McKinley

Mineral exploration programmes around the world use data from remote sensing, geophysics, and direct sampling. On a regional scale, the combination of airborne geophysics and ground-based geochemical sampling can aid geological mapping and mineral exploration. Since airborne geophysical and traditional soil-sampling data are generated at different spatial resolutions, they are not immediately comparable due to their different sampling density. Several geostatistical techniques, including indicator cokriging and collocated cokriging, can be used to integrate different types of data into a geostatistical model. However, with increasing numbers of variables the inference of the crosscovariance model required for cokriging can be demanding in terms of effort and computational time. In this paper a Gaussian-based Bayesian updating approach is applied to integrate airborne radiometric data and ground-sampled geochemical soil data to maximize information generated from the soil survey, enabling more accurate geological interpretation for the exploration and development of natural resources. The Bayesian updating technique decomposes the collocated estimate into two models: prior and likelihood models. The prior model is built from primary information and the likelihood model is built from secondary information. The prior model is then updated with the likelihood model to build the final model. The approach allows multiple secondary variables to be simultaneously integrated into the mapping of the primary variable. The Bayesian updating approach is demonstrated using a case study from Northern Ireland. The geostatistical technique was used to improve the resolution of soil geochemistry, at a density of one sample per 2 km2, by integrating more closely measured airborne geophysical data from the GSNI Tellus Survey, measured over a footprint of 65 x 200 m. The directly measured geochemistry data were considered as primary data and the airborne radiometric data were used as secondary data. The approach produced more detailed updated maps and in particular enhanced information on the mapped distributions of zinc, copper, and lead. The enhanced delineation of an elongated northwest/southeast trending zone in the updated maps strengthened the potential for discovering stratabound base metal deposits..

Jan 1, 2014

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson&apos;s ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014