Search Documents

By I Wilkomirsky, F. Parada, R. Parra, E. Balladares

"The neutral roasting of As bearing copper concentrates is confirmed well established and promising option for the treatment of this type of complex concentrate. The AS elimination by volatilization allows subsequent treatment of the calcines produced in a conventional pyrometallurgical process, by blending this product with standard concentrates.Several tests were performed using the fluidized bed pilot plant at the University of Concepción with different types of concentrates. Calcines, fines from two hot cyclones and flue dust from the ESP were collected. These materials were characterized using QEMSCAN® and the results used for the development of a mass and energy balance which took into consideration the specific chemical transformations that occurred in the reactor.A physico-chemical/kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite. The mechanism involves solid-gas reactions between chalcocite, pyrrhotite and gaseous sulfur that without the mineralogical characterization would not have been possible to propose"

Jan 1, 2014

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By P. Pyykkö, E. Peuraniemi, J. Järvi, P. V. Latostenmaa, V. Törölä, S. Junnikkala

"Nickel concentrate smelting started in Harjavalta in 1959. First, flash smelting - Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes. In 1995 the original smelter flow sheet was simplified with the novel DON (Direct Outokumpu Nickel) technology. In Harjavalta with the DON technology, high-grade nickel matte with low iron content is produced in flash smelting furnace directly without subsequent converting stage. The metal values in the smelting slag are recovered in an electric furnace as an iron containing bottom alloy. Main special features in Boliden Harjavalta nickel smelter are smelting of high-magnesia concentrates, the high recoveries of nickel and copper, as well as those of PGM`s and cobalt.Sulfur and dust emissions to air can be seen generally as one main disadvantage of nickel smelting operations. In Harjavalta continuous improvements in environmental performance has been rewarded by minimum sulfur and dust emissions to the environment and working atmosphere. Today Boliden Harjavalta’s nickel smelter is presenting state-of-art-technology at nickel smelting.This paper describes the nickel smelter process and includes recent production and emission data. It describes features required to achieve environmental and occupational hygiene goals and compares environmental performance data to that published on other smelting operations. General description of New Boliden Way is presented and a case example of production stability project is also presented."

Jan 1, 2014

By Lesley Andrews

"Electron microbeam analysis of metallurgical samples covers a broad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion.Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistlY can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of - size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis compliments bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect.This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly - more details on, and examples of, the applications and choice of technique will be covered in the presentation.Mosely first discovered, in 1913, that the frequency of emitted X-radiation excited by an electron beam is a function of the atomic number of the analysed element. This discovery led to the development of spectrochemical analysis. The forerunners of the electron microanalysers of today, however, were only invented during the nineteen fifties. The electron microprobe was developed in parallel by Castaing and Guinier in France and by Borovski in Russia, but Castaing's design was the basis of modern microanalysers. The initial area of analysis was brought down from over 1 mm2 to less than 2 µm, as it is today. In 1956 Cosslett and Duncumb invented the scanning electron microprobe, where a beam of electrons could be scanned across an area of a sample. This, in turn, led to the development of the electron microprobe with both scanning and point analysis capabilities that we know today.Essentially, all electron microbeam instruments operate by the production of a beam of electrons from a filament in a vacuum (i.e. an electron gun). The electron beam leaves the gun and is accelerated and focused by a series of electromagnetic lenses while passing down an evacuated column. The electrons eventually strike the surface of the sample to be analysed and may travel through a thin sample (transmitted electron microscopy) or react with a thicker sample to produce several reflected kinds of radiation."

Jan 1, 2014

By E. Kusaka, M. EL Salmawy

"The electrokinetic behavior of EL Maghara coal has been investigated in the presence of nonyl and octyl nonionic surfactants containing polyethoxy of different sizes with trade names of Triton-X100 (TX-100), Triton-X 705 (TX-705), Triton WR-1339 (TWR-1339) and Brij 58. The electrokinetic behavior was determined by zeta potential measurements. Zeta potential measurements were conducted by Laser-Doppler electrophoresis technique using zetamaster. The results show that the zeta potential of Egyptian coal varies with pH value, the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. It was found that the polymeric surfactants reduce the negative values of zeta potential of coal. The shift of PZC of coal upon deashing appears to be closely relevant to silicate mineral removal."

Jan 1, 2014

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By Mark S. Rayson, Jessy Lee, David O. Johnson, Matthew R. Rawls

The ability to manipulate the structure of liquid chemicals in an explosive is important in mining applications, where precision blasting is crucial for the safe, reliable, economical and eco-friendly extraction of ores. Static mixers allow explosives, emulsion-based in particular, to be custom-made as they offer precise and reproducible mixing without the need for moving mechanical parts. In this paper, we perform numerical simulations on the laminar mixing of two nitrate-based fluids in a Kenics static mixer unit for various mixer parameters. Two numerical methods were investigated in the study of the mixing pattern: solving the mass transfer equation and using particle tracking. The former introduces artificial numerical diffusion which can lead to spurious smearing of the component boundaries, a problem that can be avoided with the latter technique. We have also demonstrated that the particle tracing method is capable of qualitatively predicting the blending patterns under the conditions studied.

Jan 1, 2014

By Rolf Lauten, Yongjun Peng, Yufan Mu

"Biopolymers, produced from cellulosic biomass, have promising prospects of application as depressants in mineral processing. In this study, three different types of biopolymers (i.e., DP-1775, DP-1777 and DP-1778) were used to study the effect of polymer structure on flotation of un-activated pyrite, copper activated pyrite and chalcopyrite. It was found that the depressing effect of DP-1775 and DP-1778 was much stronger than that of DP-1777, and pyrite was depressed to a greater content than chalcopyrite with the same biopolymer at the same dosage. The biopolymer concentration played a vital role in determining the degree of depression. For each biopolymer, the higher the concentration, the greater the minerals were depressed. The mechanism underpinning the depressing effect of these biopolymers was explored in this paper. The concentration of biopolymers could determine the properties of the adsorption layer and the confirmation of biopolymer chains on mineral surfaces. The biopolymer molecules may aggregate when polymer concentration was over a critical value. Molecular weight and functional groups of biopolymers were the key factors characterizing the depressing capability of different biopolymers. Differences between the tested biopolymers and features of the adsorbed layer might account for the observed trends in ability to depress pyrite and chalcopyrite flotation. The greater depressing effect of biopolymers on pyrite over chalcopyrite might result from the preferential adsorption of biopolymers on pyrite over chalcopyrite."

Jan 1, 2014

By Venkataramana Runkana, Shantanu Maheshwari

As the world reserves of high quality ores are getting depleted at a rate higher than ever, the liberation of valuable minerals from low grade ores is becoming more and more relevant and imperative. But, liberation of minerals from low grade ores requires grinding of ore to extremely fine sizes. High energy milling in a planetary ball mill is one such option where one can produce particles in the nano-meter range. Although planetary mill is employed extensively for ultrafine grinding, dynamics of grinding inside the mill is not fully understood because of the dependency of grinding kinetics on many interconnected phenomena like collisions between media, particles and wall, time dependent rheology, adsorption and desorption of dispersant, abrasion of media, agglomeration of particles, etc. It was well articulated in literature that media motion and number of media collisions have strong effect on grinding kinetics and final product size distribution. Simulations were carried out using the discrete element method (DEM) to compare the performance of a planetary mill with a ball mill, with and without lifters, in terms of impact energy and number of collisions and it was found that number of collisions is considerably high in the planetary mill. The high number of collisions might be the reason for production of ultrafine particles in the planetary mill. We have also fitted a population balance model (PBM) to experimental data from a laboratory scale planetary mill for prediction of particle size distribution. Unlike previous models, we have incorporated functional forms for the selection function and the breakage distribution function so that the number of parameters in the PBM is just five. The predicted product particle size distributions at different grinding times are in reasonably good agreement with experimental data.

Jan 1, 2014

By Christopher Mark

Colombia is 11th largest coal producing nation in the world, and the world?s fifth largest coal exporter. But while most of Colombia?s coal is mined at large modern surface mines located near the Caribbean coast, there are also underground mines that produce high-grade metallurgical coal. These mines employ traditional hand-loading techniques in a variety of geologic environments, and they have some of the highest accident rates of any Colombian industry. The National Institute for Occupational Safety and Health (NIOSH) has been collaborating with POSITIVA, the primary provider of worker?s compensation insurance to the Colombian underground coal industry, to reduce the economic and social cost of rock falls in these mines. The specific goals of the collaboration are to 1) document practices and conditions in Colombian underground coal mines, 2) identify relevant international best practices, and 3) provide recommendations for developing a national campaign to reduce fatalities and injuries associated with roof falls. NIOSH conducted a survey of seven underground coal mines in four separate coalfields. Five of the mines were characterized by steep dips and weak roof and floor rock. The coal was loaded by hand at all seven mines, though two employed partially mechanized longwall techniques. Wood posts were by far the most common ground support. Roof bolts were not observed in use at any of the mines, and they are unlikely to replace timbers any time soon. While long-term entries generally appeared to be adequately supported, the survey found that less attention was paid to the temporary support that is installed right after the coal is removed. This temporary support is critical for protecting the workers from rock falls, however, because with hand-loading mining methods most of the activity takes place between the permanent supports and face. The study concluded that improving the temporary support in the working faces would be the most effective way to reduce the number of rock fall injuries. The key principle should be that every worker is protected by planned roof support at all times. Ground Support Management Plans, consisting of specific rules about when, where, and what roof support is to be installed, should be the focus of the campaign. Each Plan should be tailored to a specific mine based on the geologic conditions and mining methods in use. The Plan provides miners with clear, simple rules that can be easily understood, while management can easily check to see if it is being followed. Ground Support Management Plans will also provide the campaign with a concrete focus for the necessary cultural change.

Jan 1, 2014

By Lon Santis, David Buckwalter, Ken Steinmetz

This paper describes a magazine security system using two readily available cellular telephone-based technologies. The system is comprised of vibration sensors and remote cameras. The system is used at a Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF) licensed explosives storage location in Pennsylvania to comply with PA Department of Environmental Protection (PADEP) regulations. The system provides instant notification to the licensee via cellular modems, text messaging, phone call, and e-mail. Likewise, the licensee can control the system remotely over the internet and using text messaging commands. The vibration sensors attach to the door of the metal type I magazines magnetically and detect any movement or vibration. The cameras trigger on movement and thermal radiation changes and can also be triggered manually to check alarms received from the vibration sensors. The previous system was comprised of a base unit and magnetic strips. The magnetic strips were powered by a hard line from the control unit and mounted on the doors and top of magazine creating a bond, that when broken triggered an alarm. Our main issues with the unit were the delay in alert times and tech support. Because of these issues, we decided an upgrade was necessary. Compared to that previous system used at this site, these new systems are highly affordable, carefree and reliable.

Jan 1, 2014

By Nani Pajunen, Kari Heiskanen

"Products filling our societal needs, like communication and transportation needs, are becoming more sophisticated and efficient. The cost has been an increased complexity of material combinations. The same trend is also seen in investment goods. As an example, different crusher types have almost doubled the power to weight ratio in a relatively short time while producing even higher crushing rations. This has been possible by high performance materials and advanced designs. Another example is new hybrid materials in prefabricated high-strength steel structures in construction with the aim to lighten the products and obtain energy savings in the use phase e.g. in transportation. This development in general has made the end of life phase obscure. Recycling is often understood as the first phase of the material cycle. This has been supported by the material centric point of view. When, say indium, has been collected and mechanically treated to a concentrated fraction, it is assumed as recycled. This is not the case. The same applies to special steel alloys where one tends to lose some of the alloying elements to slag or even into the gas phase in the melting and refining stage, not in the earlier steps of recycling. At present there is no clear understanding of recycling of hybrid materials and no clear willingness to create new functional recycling systems. As the EU directives and most of legislation worldwide are based on the material centric thinking and implemented even on total mass recovery basis there is neither legislative incentive nor very strong economic incentives to work out the problem. In our research, we focus on industrial design towards sustainability from a product centric point of view from product collection to final metallurgical steps. It is vital, in the design phase of product, to understand the effects of decisions on recyclability to a saleable raw material. Main goal of our work is to create the fortunate circumstances in supply chain - to pass the barriers and find the effective and fruitful drivers - for reasonable use of raw materials and recycling co-operation with industry. The boundary conditions in the work are extractive metallurgical performance and the economic viability of all the steps. It can be shown from our work that small design alterations may have a large impact on the recyclability. The earlier the decisions are made in the product life chain the more positive impact they will have. It can also be shown, that a strong processing and metallurgical industry is vital to any meaningful recycling of the modern EoL products. Finally, it is also question of the individuals and values: supply and demand. Are you ready to take up the gauntlet: demand recyclable products."

Jan 1, 2014

By G. Demi

Chromium ore exploitation has commenced in 1948 in Albania and there are produced about 24.3 million tons up to the end of 2006. Last years the prices and need were increased notably. Main export of chromium ores and concentrates was accomplished respectively 114 500 ton and 13 000 ton in People Republic of China during 2006 year. Location, status, reserves and grade of chromium deposits of Albania are presented in the paper. Chromium ore enrichment is related with their composition and Cr2O3 content, as well as with market requests. Actually, high grade chromium ores with Cr2O3 content over 38% ~ 40% are directly exported or treated in metallurgy, but last time have been exported and chromium ores with 28% ~ 30% Cr2O3 content for the reason that dressing plants can not be operated for investment lack. High grade chromium ores have been treated in heavy media separation plant before 1990. It is presented flow sheet, figures and necessity to put in operation HMS plant in the paper. Actually, low grade chromium ores with content 16% ~ 20% Cr2O3 are not enriched for the lack of investments, but before 1990 they have been concentrated in dressing plants producing chromium concentrates grade 48% ~ 50% Cr2O3. In the paper are shown technological schemes and industrial figures during more than 20 years operation and possibilities to reconstruct these mineral processing plants. Only chromium mineral processing plant of Bulqiza is in operation using as raw material its old existing tailings. The flow sheet and figures show that are possibilities to increase recovery and grade of concentrate in the plant. Separation and concentration of slimes in suitable equipment gives visible improvement of Cr2O3 recovery. Several tests have been carried out with flotation and magnetic separation methods for enrichment of low grade chromium ores. Flow sheet and figures of mineral processing ores content olivine as gangue mineral are interesting, because combination of gravimetric with magnetic methods is necessary in this case. In the paper are presented the tests and good results of low chromium ore pre concentration. Metallurgical treatment of chromium ores to produce Ferro chrome, as well as technological process, figures, consume of electrical power and materials in Elbasani and Burreli furnaces are shown and necessary investments to treat in metallurgy all produced chromium ores in Albania are considered.

Jan 1, 2014

By A. C. du Preez

Mintek has been involved in extensive test work since the early 1990s on the recovery of nickel and cobalt from leach liquors saturated in calcium, using synergistic solvent extraction systems. During this period the Nicksyn? reagent was developed, optimized, commercially manufactured, and tested by Tati Nickel on a demonstration plant for more than 2800 operating hours. Efficient recovery of nickel without the co-extraction of calcium, thus avoiding gypsum formation in the extraction and stripping circuits, was illustrated. This synergistic system was recently evaluated on a laboratory scale for the recovery of nickel and cobalt from synthetic lateritic sulphate leach liquor containing about 3 g/L nickel, 0.5 g/L cobalt, 0.7 g/L manganese, 20 g/L magnesium, and with calcium at saturation. Extraction and stripping parameters were determined for this feed liquor and are discussed in this paper.

Jan 1, 2014

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By T. Deng

Flotation of rare earths is complicated by the number of mineral classes that carry rare earth elements, including carbonates, phosphates, and silicates that often co-occur within the same deposit. Gangue constituents often belong to the same mineral classes as the rare earth minerals themselves. Chemical regimes developed for specific separations employ customized combinations of collectors, modifiers, and depressants that are not directly translatable to other operations. In this rougher flotation case study, a reagent suite including phosphate ester and sulfosuccinamate, originally developed for the recovery of bastnasite and monazite from silicate hosted ore, could not be applied to a synchysite ore hosted in carbonate gangue because the suite was aimed at silicate gangue rejection only. The separation of a fluorocarbonate mineral from carbonate gangue required a different chemical regime involving the use of hydroxamate and sodium silicate. Maximizing rare earth recovery was complicated by the presence of slimes. The effect of desliming and the increase in grind size was explored.

Jan 1, 2014

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014