Search Documents

By Luís Marcelo Tavares, Daniel Francioli, Malcolm Powell, Mohsen Yahyaei

"Mathematical modeling of the comminution process requires understanding of all breakage mechanisms occurring in this mechanical environment. Modeling of high energy impact breakage is well established, however, modeling low energy breakage including incremental damage breakage, attrition and abrasion is still under development. Free fall incremental impact tests were carried out to investigate the surface fragmentation of a copper-gold ore. This process was achieved by dropping particles individually from a height of four meters onto a metallic plate. The impact specific energy was 0.01KWh/t. The setting of the metallic plate was changed to test the impact angles of 0°, 45°, and 60°. Tests were carried out using fresh angular rocks as well as smoothed particles. Changes to the plate angle and particle shape enabled the study of the influence of the tangential component of the impact energy along with particle shape on superficial breakage. By studying the fractional mass loss variation in each impact, two distinct stages of surface fragmentation were clearly determined: high fractional mass loss dominated in the first 10 impacts and was attributed to chipping, whereas low fractional mass loss occurred for the remainder of the impacts and was attributed to abrasion. Smoothed particles demonstrated higher resistantance to breakage and their surface fragmentation behavior indicated a closer relationship to abrasion, especially when lower impact angles were used."

Jan 1, 2014

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

Results of flotation process combined with atmospheric leaching and high pressure leaching for recovery of copper from low-grade silicate-copper ore have been presented in this study. The low-grade copper ore contains a small amount of copper (0.42 mass %), iron (4.6 mass %), and silicon (38.3 mass%) and among many other metals (Al, Ca, K, Mg, Na, Ti and S). The main mineralogical constituents of the copper ore are calcium aluminosilicate (Ca(Al2Si2O8), amesite (Mg2Al2SiO5(OH)4) and gypsum (CaSO4×H2O), and quartz (SiO2) as resulted from the alteration of an igneous rock. This study has shown that about 92 % of copper can be recovered with a maximum copper grade of 4.2 mass% in a froth after 15 minutes of flotation at pH 8.5 when used potassium amyl xanthate as a collector, MIBC and Dow-froth 250 as frothers and calcium hydroxide as a pH adjuster. The images of bubbles in the cell during flotation process were recorded using a high-speed camera. The froth concentrate with average copper grade of 2.0 mass% was further processed by atmospheric leaching with a solution of sulphuric acid and hydrochloric acid, respectively and high pressure leaching with sulphuric acid solution. As a result, leaching rate of copper reached about 60 % in an atmospheric leaching with sulphuric and hydrochloric acid respectively, whereas the rate can reach more than 70 % by autoclave leaching at high pressure under the controlled condition. A process to recover of copper from its low-grade ore can be developed by optimization of flotation combined with acid leaching.

Jan 1, 2014

By B. Csoke

To improve the efficiency of the crushing/screening plant of Bazalt-Középko Kobányák Ltd. (Hungary), the implementation of computer aided quality control is planned. In the current phase, the R & D work aims at the solution of high-priority tasks: 1) Developing the process models, validation of the models by means of industrial measurements. 2) Developing the algorithm for the process control of the crushing/sizing plant. 3) Developing the suitable computer program. To develop the mathematical models of crushing (breakage and probability functions) and to determine the model parameters, the experimental industrial trials were carried out on hydrocone crushers of types Svedala H 4800 EF and H 4800 F, changing the gap size and crushing relatively narrow grain size fractions. Additionally, the parameters of the separation function for the screens operating in the system were determined. It was established that the crushing probability depends on the grain size of the feed (Y) and the gap size (s), so the breakage probability S, for each cone crusher, can be well characterised by the function formed using the ratio of these two parameters: SfYsf==. The distribution of the broken grains can be described reliably using the relative grain size distribution function B(? = x/Y) (usually Schuhmann-Gaudin- or Rosin-Rammler-shaped function). For the screens, the probability function ()2()111/NTx = xd ???---???? is suitable for cha-racterising the separation (where x? grain size, ?-open-area ratio, d ? rectangular screen aperture size, N ? number of appearance of the particle on a screen surface). Using these functions, the comminution circuits were described by means of vector/matrix equations. The calculations and measurements verified the reliability of the developed models and algorithms.

Jan 1, 2014

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By X. Q. Cao

As the second largest phosphate resource in the world, Chinese phosphate ores generally grades with low of P2O5. The presentation of beneficiation test on the low grade of phosphate rock in this paper may be used for a reference for development and utilization of the similar reserves. The ore is a marine sedimentary phosphate rock containing low grade of P2O5 and high content of MgO and R2O3; The banded structure shows its suitability for heavy medium separation. The laboratory heavy liquid testing results indicate that as specific gravity of the heavy liquid is 2.85 g/cm3, a rougher concentrate assaying 28.71% P2O5 could be obtained while the rougher tailings contain only 4.47% P2O5. When the combined process with heavy liquid separation followed by direct & re-verse flotation is employed to treat the feed containing 21.15% P2O5, 3.79% MgO, 1.86% Fe2O3, 3.66% Al2O3, 23.75% A.I, and specific gravity of heavy liquid is 2.84 g/cm3, the optimum mesh of grind is 67.5% minus 200 mesh, a phosphate concentrate contained 32.51% P2O5, 0.48% MgO, 0.81% Fe2O3, 1.69% Al2O3 can be produced at a yield of 55.24%. The concentrate P2O5 recovery is 85% with which quality comply with the Class A specifications for production of phosphate fertilizer.

Jan 1, 2014

By H. Salomon-de-Friedberg

The amount of pyrite in copper concentrates fed to the CESL Process can vary appreciably. The fraction of pyrite that oxidizes influences both capital and operating costs and is therefore an important variable. The present paper explores operating conditions that influence the extent of pyrite oxidation and the probable overall reaction chemistry under CESL conditions.

Jan 1, 2014

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

By Jorge Misle, Daniel Silva

"This paper addresses the need for advanced control technologies and strategies in the mining industry, its potential and actual impact on mining processes and the best practices for their implementation, operation, and long term sustainability. It is well known that advanced process control (APC) can be a very good source for incremental process improvement for the mining industry, yielding to higher production rates or helping maintain consistent production rates despite ore changes. The application and integration of new technology, process knowledge and innovation are key elements in building such a supporting structure. More specifically, and this cannot be emphasized enough, the correct application and assembly of control tools, the in-time presentation of key data to decision makers and the development of relevant statistics and KPI’s (key performance indicators) can and will make a difference not only in terms of production, but also in plant stability, availability and production costs. In deploying such ideas and aiming at the long-term goal of "Operational Excellence", Minera Los Pelambres (MLP) has developed a number of successful control strategies, best practices and technologies, which are not only the application of state-of-the-art automation and computing tools, but rather the assembly of the above presented structuring factors. This work discusses some of the key tools and ideas implemented for SAG & Ball milling and Flotation areas, their performance results and the roadmap taken for the integration of process knowledge and control tools. Also, cases studies are presented and discussed further to not only show the main areas of improvement, but also to highlight the benefits of such strategy that for the most part, deviate from the traditional mining industry control approach. Also, a word is given on the need for innovating in the design of control strategies and leveraging best practices and process knowledge that ultimately, will contribute to long-term reliable operations, improved mineral processing and, although unmeasured, lead to a superior overall performance and productivity of all mining personnel involved."

Jan 1, 2014

By Hristo Stanchev, Veselin Mehandzhiyski, Sashka Kozhuharova, Stefan Stamenov, Alexandar Penchev, Nikolay Nestorov, Velika Stamatova, Ekaterina Todorova

"This article presents the results of comprehensive research on the quantitative distribution of gold content in the raw ore and tailings from the flotation enrichment process at the Ellatzite Med plant. The study is a quantitative and qualitative determination of the presence of gold in the ore processed by Ellatzite Med AD, as well as its behavior and distribution in the various metallurgical products of the flotation process. The representativeness of the samples taken is ensured by the frequency of sampling: four work shifts of sampling on different days within a period of four consecutive weeks. The form of gold present is determined both in the analyzed samples and in separate fractions - granulometric, magnetic, electromagnetic, heavy and light. A summarized diagram presents the phase distribution of gold in the final products of the dressing process. The results obtained are used for further analysis and evaluation of the actual technological parameters of the gold. It was established that an increase in the initial gold content, respectively in the content of native gold in the raw ore, with the current process, leads to an increase in gold losses, mostly in the native gold phase. The conducted analysis of the results from the comprehensive tests on determining the form of gold present in the various enrichment products gave rise to further research with the use of a Knelson centrifugal concentrator."

Jan 1, 2014

By G. Y. Liu

The structure-activity relationships for four thionocarbamate collectors are discussed in this pa-per. These collector classes are alkyl alkyl thionocarbamates, allyl alkyl thionocarbamates, acyl al-kyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates. The main emphasis will be to highlight the differences between collectors and their affinities for copper and iron sulfide minerals on the basis of data on electronic-structure properties obtained by vacuum and solution density functional calculations, flotation experiments and analysis measurements. The mechanism of interaction of these collectors with sulfide minerals is also discussed with perturbation theory. The theoretical study results indicate that acyl alkyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates have best performance in these agents as flotation collectors with improved collecting power for copper sulfide minerals and excellent selectivity against iron sulfide minerals, which are consistent with the experimental data reported in the literature.

Jan 1, 2014

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By B. Vasanthakumar, H. Ravishankar, S. Subramanian, J. Braun

The flotation of sphalerite and galena in the presence of intra- and extra-cellular components isolated from Bacillus circulans before and after adaptation to the chosen minerals has been studied. Based on various biochemical treatments, the key biomolecule primarily responsible for the flotation of sphalerite has been identified as DNA, which functions as a bio-collector. A noteworthy finding is the considerably higher flotation recovery of sphalerite obtained in the presence of single stranded DNA (79.8%) vis-à-vis double stranded DNA (50.2%). Selective flotation tests using the soluble fraction obtained after thermolysis treatment highlight that sphalerite-adapted cells yield a higher selectivity index (S. I.) of 31.2 compared to galena-adapted (S.I. 4.3) or unadapted (S.I. 12.2) cells. During bacterial adaptation to the above chosen minerals, the quantitative and qualitative changes in the surface potential, surface morphology and cell wall components have been monitored. The prior adaptation of the bacteria to sphalerite results in the secretion of a higher amount of proteins, eDNA and phosphate, whereas adaptation to galena leads to a higher amount of polysaccharide, uronic acid and acetylated sugar, vis-à-vis the unadapted bacteria. A significant observation is that the bacteria undergo a change in morphology from rod to sphere as a strategy to resist metal toxicity during adaptation to galena. Interestingly, this phenomenon is not observed during bacterial adaptation to sphalerite. This morphological transition has been shown to involve changes in crucial cell wall components as well as changes in the levels of expression of bacterial cytoskeleton element mreB gene involved in the maintenance of the rod shape. The sequence of B.circulans mreB gene has been identified using Polymerase Chain Reaction (PCR) followed by DNA sequencing.

Jan 1, 2014

By G. C. He

Effects of irregularity, rough surface and aggregation of fine particles on ultrasonic attenuation are significant. The effects should be considered while predicting particle size by ultrasonic attenuation technology. The scanning electron microscope micrographs analysis also shows that particles surface is rough and irregularity. Any slurries has its fractal structure and its special fractal scale and dimension, so, effects of irregularity, rough surface and aggregation of fine particles can be de-scribed by fractal model. The discrepancies between predictions of ultrasonic attenuation based on the assumption of smooth spherical particles and data obtained from slurries of irregular particles indicated that there were different fractal structures. The ultrasonic attenuation model was modified by fractal dimensions. The result of experimental data and analogue calculation indicated that pre-dictions of the fractal modification of ultrasonic attenuation model show good agreement with experimental data. On the other hand, from the values of fractal obtained by inversely calculation, the degree of effects of irregularity, rough surface and aggregation of particles can be estimated. The positive value of fractal dimension indicates that the aggregation has the dominant effect on ultra-sonic attenuation, otherwise, the irregularity and rough surface has the dominant effect.

Jan 1, 2014

By M. H. Kotze, V. Yahorava

A gold-selective ion exchange resin, containing tributylamine groups, was developed by Mintek for the recovery of gold from cyanide leach solutions. The Dow Chemical Company and, more recently, Purolite commercialized the production of this gold selective resin for use in the gold mining industry, and it is marketed as Dow XZ-91419.00 and Purolite A194 respectively. A novel application of this resin is the selective recovery and separation of AuCl4 - f rom p latinum group metals (PGMs) in chloride and nitrate solutions. The current paper describes potential benefits of this type of resin for selective recovery and upgrading of gold from low grade chloride or nitrate waste streams, and the possibility of gold separation from PGMs during their refining in chloride media.

Jan 1, 2014

By C. Joulian, A. G. Guézennec, A. Chmielarz, Y. Ménard, M. Hanke, P. d’Hugues

"The copper concentrate used in this study is produced by flotation of a black shale organic rich ore. This resource is a carbonate-rich, polymineral concentrate. In the last 5-6 years, ore characteristics changed and the concentrate grades degraded. This study evaluated bioleaching of the concentrate in stirred tank reactors as an alternative to the pyrometallurgical technology that is currently applied, and which may no longer be feasible in future given the concentrate chemistry.The first part of the study focused on testing non-traditional operating conditions during continuous bioleaching experiments: high solids concentration (> 20% solids), reduced agitation and aeration rates. For the same residence time, bioleaching performance at high solids loading (25%) was the same as that reached during previous bioleaching experiments at 15% solids. No mixing or microbial issues were encountered. The bacterial consortium used in the experiments demonstrated a high copper tolerance.The second part of the study was devoted to technology development for metal recovery from copper bearing solutions obtained during bioleaching experiments. Due to the high copper concentration of the leachate, solvent extraction prior to electrowinning was not necessary. After iron removal, high quality copper cathodes (morphology and composition) were obtained from the PLS by electrowinning."

Jan 1, 2014

By Zainelabdin Khalid Zainelabdin Elfaki

The influence of partially replacing cement with marble waste on the workability and compressive strength of concrete bricks was investigated. Three replacement percentages, 10%, 20% and 30% weight marble waste, were used with different curing times of 7, 14 and 28 days. Two specimens were prepared for each percentage and curing time. For this study, marble powder from the Mining House Company in Saudi Arabia was used. It was observed that the replacement of cement in Concrete brick with marble waste enhanced the loading strength and the workability of the prepared concrete bricks. It was also observed that 20% replacement of cement with marble waste was the best replacement percentage compared to the other replacement percentages tested. Marble waste from manufacturing companies, either in powder, sludge or slab form, has negative impacts on the environment. In contrast, reusing marble waste has both economic benefits (i.e., selling the marble waste) and lessening the need for raw resources.

Jan 1, 2014