Search Documents

By G. Önal

Recovery of nickel and chromite from the tailings has been studied on the samples with 0.214 % Ni and 5.10 % Cr2O3 content and taken from Orhaneli Chromite Concentration Plant. Mineralogical examinations of the samples showed the existence of chromite, olivine, pyroxene, chrysotile, anti-gorite, chlorite, idingite, tremolite and calcite together with trace amounts of millerite, pentlandite, pyrite, pyrrhotite, hematite and limonite type iron oxide minerals in partially serpantinized dunite type particles. In order to recover chromite from Chromite Concentration Plant tailings Mozley Table and Knelson Separator are used and concentrates containing approximately 42% and 46% Cr2O3 are produced respectively with 40% recovery. Most of the nickel remained in the tailings. Therefore, acidic leaching tests are performed in order to dissolve nickel from these tailings. Effects of particle size, acid concentration, temperature, leaching time and solid/liquid ratio on the nickel leaching efficiency are investigated. The optimum leaching conditions are found as 250 g/L acid concentration, 1/5 solid/liquid ratio, 2 hours of leaching time and 60°C temperature, almost all nickel is dissolved at the optimum conditions and acid consumption is about 841 kg/t. Repeated leaching tests are carried out in order to have enough Ni content in the leach liquor for the further treatment of solutions. After repeated leaching tests, leach liquor contains 3 kg/m3 Ni, 48 kg/m3 Fe, 2.2 kg/m3 Si, 23 g/m3 Cr and 590 kg/m3 H2SO4. Ni is recovered from that solution by precipitating with H2S followed by HNO3 dissolution and precipitating Ni as hydroxide with 63% Ni content. Leach cakes are subjected to the gravity separation (Mozley table) to recover the remained chromite and a chromite concentrate with 47% Cr2O 3 content is produced with 53% recovery. As a result of the abovementioned tests, a conceptual process flow sheet is proposed for the treatment of these chromite concentration plant tailings.

Jan 1, 2014

By Richard N. Campbell

The world?s ever-expanding demand for energy and coking coals has resulted in the underground mining industry looking at taking on increasingly marginal and geotechnically challenging deposits. The drivers for this change include a reduced availability of open cut reserves and a lack of remaining ?good coal leases?. The lack of plum deposits is forcing some companies wanting to enter the coal supply market to purchase and operate in higher risk, lower margin areas. As geotechnical professionals, we are expected to develop strategies to facilitate safe and productive mining in ground that once would have been avoided. To be successful in these reserves, we are required to use every tool available, from exploration data to longwall automation, and invent or reinvent some new tools along the way. This paper presents geotechnical case studies of challenges in longwall mining and some of the methods developed and used to allow longwall mining to succeed where others said we would fail.

Jan 1, 2014

By D. Berman, A. Brodt

"Delivery of all volume of mined mass on the terrestrial surface results not only in irrational power expenses on moving of huge volumes of dead rock as a part of initial raw materials (especially vertically) on long distances, but also necessities of storing tailings in open-air. Thus, in bowels of earth, huge volumes of the developed space are formed. However, the nature doesn't suffer emptiness. As consequence, through the process of underground mining works, in earth bowels starts intensive development of rocks dislocation processes involving subsidence of terrestrial surface, and with it, begins irreparable damage every objects which are on that territory. Highly effective new methods of underground concentration of the various minerals, which deliveries of only target component on terrestrial surface integrally connected with transport process in stream and subsequent deliveries to destination in continuous mode by the long distance hydrotransport, allow not only to eliminate a construction of concentrating factories on the surface, but also storing of tailings of concentration process on open-air preventing dislocation of rocks, thanks to operative placing tails in the underground developed space. Surely, the main problem in the development of such gravity dressing technology is the problem of finding the optimal formula for the heavy liquid that will fill such system in close connection with the procedure of its full regeneration. The requirements for such liquid are being non-toxic and cheap. This question was solved successfully."

Jan 1, 2014

By F. Burat

At the present time, methods of mining and coal preparation produce tones of coal fines. The removal of water from these fines is necessary for economical and technological reasons. Supplementary processes that utilize different physical and chemical methods have been developed to in-crease the productivity of mechanical dewatering processes. Researches have shown that chemical reagents used along with conventional systems diminish moisture and increase the capacity and the yields of the dewatering method. In this study, the parameters of the vibrating screen (incline, frequency, feeding rate and screen size), the effects of the application of additional vertical mechanical vibration and surface active reagents (CTAB, SDS, Umectante B-70 and Kerosene) were investigated. At the end of the optimization experiments, 61.0% moisture was decreased to 42.3%. By keeping optimum conditions con-stant, the experiments have been conducted to determine most effective reagent. 41.2% moisture has been obtained with 5 g/t CTAB at the normal pH of the pulp, which were 7.25. By using vibrating screen with combination of the vertical vibrating mechanism, CTAB gave the best result of 40.7% moisture. Finally, the effect of increased surface area of the screen has been investigated and de-creased the moisture level to 38.7%.

Jan 1, 2014

By B. D. Pandey, M. S. Kim, B. S. Kim

The recovery of Sn from used Pb-free solder (Sn, 3~4 % Ag, < 0.9 % Cu, < 1.2 % Pb) has been investigated by electrorefining in sulfuric acid solutions containing small amount of hydrochloric acid. This involved preparation of the anode material by melting and casting the used solder followed by refining. During electrorefining, dendritic tin was deposited on stainless steel cathode. Increasing the amount of hydrochloric acid up to 0.3 mol /L in the electrolyte enhanced the current efficiency to 92.2 % and the enrichment ratio of silver to 94.3 % in the anode slime which was otherwise 84.7% and 81.6 % in absence of HCl, respectively. The electrolyte containing hydrochloric acid has also prevented the precipitation of tin oxide in the bath. In the scale-up experiment using 1.6 kg anodes, 84.3 % current efficiency and close to 100 % Ag enrichment ratio were obtained, while the purity of electro-refined tin was over 99.9 %. The energy consumption of the winning process was found to be 0.151 kWh /kg-Sn which is competitive as compared to commercial tin electrorefining processes.

Jan 1, 2014

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By J. Budac, R. Kofluk, S. Mankasingh

Stainless steels such as 316L or 304 are normally relatively resistant to attack by nitric acid. However research at Sherritt International’s Fort Saskatchewan Operation reveals that when the stainless steel is immersed in an aqueous system in which nitric acid is used to dissolve metals such as cobalt or nickel, the steel can be seriously corroded. Sherritt is patenting a simple process for arresting the corrosion via the use of copper. This process is expected to substantially eliminate corrosion in processes where nitric acid is used to dissolve metals attached to a stainless steel substrate.

Jan 1, 2014

By S. V. Balikov

A close association of fine gold with pyrite and arsenopyrite is observed at many gold ore deposits. Gold forms and gold distribution in sulfides of different deposits were studied. A comprehensive method including optical spectrum analysis, X-ray diffraction analysis, high-temperature X-ray diffraction analysis, scanning electron microscopy and X-ray microanalysis was used for the de-tailed investigation of the defectiveness of the structure of pyrites from different deposits. It was shown that gold content in pyrites varied from 1.5 g/t to 100 g/t compared with 30 g/t to 230 g/t in arsenopyrites. The nature and arrangement of inner inclusions of foreign minerals in pyrites as well as occurrence of fractures and macro- and microdefects were examined. Iron, sulfur and arsenic contents in all pyrite samples were determined. Chemical composition of the detected inclusions was defined. Parameters of submicroscopic structure of pyrite were estimated using X-ray Fourier line shape analysis. Estimation of real structure characteristics with calculation of submicroscopic D-blocks and root-mean-square lattice deformation 2()evalues was performed. Defectiveness of the pyrite structure can be defined by the following parameters: K?1 and K?2 reflection resolution and its intensity within high Bragg angles; S content to Fe content ratio; the arsenic content and the local variation in its concentration within the pyrite grain; the size of submicroscopic blocks and the crystal lattice disturbance value. The performed analysis showed some relationships between these parameters and refractoriness of the pyrite concentrates. It was observed that at S/Fe ratio close to or higher than stoichiometry and at a low arsenic content (less than one per cent) pyrite concentrates were not refractory. The analysis results showed that concentrates of the Beryozovskaya gold plant (0.02~0.07 As%) and concentrates of the Kommunarovskaya gold plant (less than 0.05 As%) as well as some pyrites from the Sukhoi Log gold deposit had the same characteristics. It was found that average arsenic content did not excess 0.2 per cent. Arsenic distribution within the grain of all these pyrites was uniform. At S/Fe ratio lower than or close to stoichiometry and at high arsenic content (more than one per cent) and significant variation in its distribution within a pyrite grain the pyrite concentrates are refractory. Such pyrites are typical for the Sukhoi Log, the Bakyrchik and the Mardzhanbulak gold deposits. Direct correlation between arsenic and gold contents, in particular, in fine grains of pyrite was observed by many researches. This correlation was explained by impregnation of arsenopyrite which normally contains more gold than arsenic pyrites. The analyses results showed that no arsenopyrite impregnation was found: arsenic distribution within the grain was uniform but its concentration varied greatly. Such pyrite concentrates are more refractory. This paper presents the results of analyses of sulfides to determine the amenability of the associated gold recovery by hydro- and pyrometallurgy.

Jan 1, 2014

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from both primary and secondary sources having various compositions. Vanadium pentoxide and vanadium trioxide are the most available and known sources of vanadium oxides. In this paper, an overview of leaching both oxides has been reported. The problem of vanadium pentoxide leaching under acid conditions is the low solubility of the dissolved vanadium. This was investigated and then supplemented with further studies of leaching at mildly basic pH’s as well as under acid reductive leaching conditions (to form vanadium (IV)). Atmospheric oxidative leaching of vanadium trioxide was investigated using oxygen and ferric ion as the oxidant. It was shown that the leaching of vanadium trioxide using oxygen is very slow; however, ferric ion can dramatically increase the kinetics and leach efficiency.

Jan 1, 2014

By Gabriel C. Aguilera, Juan Arismendy

"The effect of rheological factors inside of a hydrocyclone is very relevant for the fluid mechanics and for the classification of materials on suspension, since parameters such viscosity and thixotropy are intrinsic variables that depend of the particulate system and the continuous phase; they determine the efficiency of classification. Nevertheless, the exact knowledge of the main characteristics and magnitudes of them inside the hydrocyclone is very difficult because of the geometry of the hydrocyclone, even more if the hydrocyclone is of small diameter. Hence is not possible to make a hydrodynamic study with effects over classification regarding these variables. This work studies the rheological variables inside a small diameter hydrocyclone that works at high pressures, using the information given by a model of Computational Fluid Dynamics (CFD). The model used includes the Reynolds Stress Model (RSM) for the evaluation of turbulence, and the Volume of Fluid (VOF) to study the interaction between water and air, which is very important to obtain regarding the effect of the air core over the performance of the equipment. The validation of the CFD model was done with a kaolin suspension at several conditions of solids contents below the critical volume fraction, without chemical additive aid. These conditions are representative of current work parameters on plant. As result it could be established the ranges of evaluation of rheological variables on specific regions inside the hydrocyclone, and through a rheometric study, based on the mechanic characteristics previously obtained, the main rheological characteristics of the mineral suspensions were determined."

Jan 1, 2014

By Y. Luo

In designing and operating underground room-and-pillar coal mines, it is always difficult to achieve a good balance between preventing surface subsidence and achieving high recovery ratio. In this paper, a design methodology applying the pressure arch theory is proposed, and the principles and mathematical models involved are detailed. A computer program was developed to carry out the design optimization process and was applied to the examination of a documented case in which a massive cascading pillar failure had occurred over a large area in a shallow coal mine. The results indicate that the proposed design method can be applied to prevent subsidence while achieving reasonably high recovery ratio for roomand- pillar mining operations.

Jan 1, 2014

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Ben Murphy, Alejandro Yanez, Tatu Miettinen

"Flotation using large volume cells has grown in importance during recent years, particularly given the increasing demand for minerals whilst ore grades are decreasing. Outotec introduced the TankCell® e300 in 2007 to enable concentrator plants to process these higher tonnages. From the beginning, TankCell® e300s with FloatForce® mixing mechanisms have demonstrated good metallurgical performance with decreased operating costs and high availability. This paper deals with specific engineering challenges that need to be considered when installing these units rather than giving examples of performance. Today there are over 100 TankCell® e300s operational worldwide. As more of these units are installed new technical challenges are encountered and solutions developed to maximize their productivity. Lessons have been learnt by operators, engineering companies and the cell manufacturers on how best to design and layout these cells in modern concentrators to ensure smooth transition from design to installation to operation. This paper presents information on important design considerations and learning that has been obtained through the design, installation and commissioning of the TankCell e300 around the world. Areas pertaining to cells layout such as feed and discharge arrangements along with items of metallurgical concern such as sampling, reagent addition and the potential benefits of installing a variable speed drive on the motor will be covered in depth."

Jan 1, 2014

By O. J. Restrepo-Baena, L. Rojas-Mendoza

Gold losses must be controlled during extracting processes, especially during cyanidation. Otherwise recovery decreases and therefore the profitability of projects too. One of the phenomena that generate such losses is known as preg-robbing which occurs when some mineral constituent adsorbs aurocyanide complex from a cyanide solution. There are some laboratory methods to identify potential preg-robbing in gold ores, highlighting the PRP method, the BGMI test, and cyanidation tests by conventional agitation without activated carbon (BRP) and with activated carbon (CIL). For this study we performed an initial characterization of a sample from Antioquia - Colombia and then we carried out the methods described above in order to identify the presence of carbonaceous matter. We obtained a percentage of preg-robbing of 78.7% by applying the BGMI test; the preg-robbing potential by the PRP method was 97.9% with an extraction of 0.77% and an inferred recovery of 36.6% if preg-robbing did not occur. Finally we obtained under the BRT test a recovery of 0%, while for CIL test an extraction of 33.6% what confirmed the presence of preg-robbers agents in the gold ore. We conducted all tests in the Institute of Minerals - CIMEX at Universidad Nacional de Colombia - Medellin.

Jan 1, 2014

By P. E. Hand

Coal is a complex heterogeneous commodity that can be mined in a number of ways and needs to be processed to a homogeneous quality that satisfies the customer?s requirements, while attempting to maximize revenues. Only a small proportion of coal is suitable for metallurgical use. Export coals cover a wide range of qualities and some coals can be used optimally in the raw state for energy production. Critical quality parameters vary and can be a combination of heat value, ash, volatiles, sulphur, phosphorus, sizing, amongst others. The level of beneficiation is generally dictated by the washability of the coal, mining contamination, and the target product quality. The steps in the coal chain covered in this paper comprise exploration, mining selections, production, the washing process, and product delivery. Many points of sampling are needed to maximize yield at the correct quality, and some of these will be described in the paper. Keywords coal chain, coal beneficiation, sampling.

Jan 1, 2014

By J. -C. Sztuke, M. Cao

ABSTRACT Wash water and polyethylene oxide (PEO) were used in the flotation of quartz and coal. Wash water decreased entrainment of –15 µm quartz. The optimum superficial wash water rate was 0.05 cm/s. PEO also lowered entrainment. The combination of wash water and PEO led to a slight further reduction in entrainment. For 1:1 mixtures of –15 µm quartz and –300 µm oxidized coal, the combined use of wash water (0.05 cm/s) and PEO increased the separation efficiency from approximately 30% to > 70%, whereas wash water alone at 0.05 cm/s did not lead to a discernible increase.

Jan 1, 2014

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014

By R. E. Baylis, M. R. Tolley, S. Singh, A. J. Murray, R. Boden, L. E. Macaskie, T. P. Hathway, D. Vavlekas

We report rare earth element (REE) recovery using immobilized Serratia biofilm depositing metal phosphate via a robust enzymatic mechanism. Activity was approximately halved at pH 3.5 and restored at pH 5.5. REE(III) was recovered selectively against Th(IV) but the method was non-selective between different REEs (La, Y, Eu, Nd). Biofilms were active for a year (half life of ~ 3 months). The activity of aged biofilm was enhanced by pre-nucleation (‘priming’) with NdPO4 prior to onset of flow-through conditions. The use of different ‘priming’ metals and bacteria via a combinatorial approach revealed some REE selectivity through the selective exclusion of specific REEs.

Jan 1, 2014

By J. M. Mwase

The platinum group metal (PGM) industry is currently reliant on the crush-mill-float-smelt-refine route to process PGM ores. However, there are many instances where this route would not be feasible. An alternative process route has been developed which involves heap bioleaching to extract base metals followed by heap reclamation and a water wash step, leading into heap cyanide leaching to extract precious metals. This process was evaluated through test work on samples of Platreef ore using laboratory scale columns. After 304 days 75% Ni and 93% Cu were extracted in the bioleach experiment at 65°C, and after 60 days 58% Pt, 99% Pd and 90% Au in the follow-up cyanide leach experiment at 50°C. A preliminary process flow sheet has been developed around this. Analysis via a mineral liberation analyser showed that the remaining Pt was in the form of the mineral sperrylite, which appeared to be slow leaching in cyanide in comparison to the other mineral types. Analysis of cyanide effluent solution showed high levels of thiocyanate, which present an environmental risk for disposal and high consumption of cyanide. Further studies to develop the process for commercial application in the South African PGM industry are outlined.

Jan 1, 2014

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014