Search Documents

By Yilin Fang, Alain Bonneville, Timothy. D. Scheibe, Zhijie Xu

"We present a hydro-mechanical model for geological sequestration of carbon dioxide. The model considers the poroelastic effects by taking into account the coupling between the geomechanical response and the fluid flow in greater detail. The simplified hydro-mechanical model includes the geomechanical part that relies on the linear elasticity, while the fluid flow is based on the Darcy's law. Two parts were coupled using the standard linear poroelasticity. Analytical solutions for pressure field were obtained for a typical geological sequestration scenario. The model predicts the temporal and spatial variation of pressure field and effects of permeability and elastic modulus of formation on the fluid pressure distribution.IntroductionIn order to achieve a substantial reduction of CO2 emissions and alleviate the atmospheric carbon problem, massive scale carbon sequestration is required involving millions of tons of carbon dioxide injection over several decades. The geomechanical response is important upon the injection of substantial supercritical carbon dioxide into deep geological formations. Supercritical CO2 is less dense than brine waters and the buoyancy driven flow of CO2 requires the aquifer to be capped by low permeability rock (""caprock"") to prevent the upward migration of C02 (as shown in Fig.1 ). Massive scale injection of C02 changes the overall stress state in the caprock and formation. This change leads to large deformation that can damage the caprock, create fractures, and open new flow paths for supercritical C02. Therefore, a coupled hydromechanical model becomes essential for the caprock integrity analysis."

Jan 1, 2012

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

Develop a safe, nonpolluting power source for underground mining equipment. Approach The Bureau of Mines and EIM-CO Mining Machinery International entered into a cost-shared project to develop and demonstrate a novel power source for mining. An underground mining utility truck was equipped with an ultra-low-emission hydrogen-fueled engine and a safe, metal hydride fuel storage system. How It Works The nonpolluting hydrogen engine and a "solid-state" (metal hyride) hydrogen fuel storage system were combined to power a utility mining vehicle. An 85 horsepower diesel engine was convened to burn hydrogen. The engine was converted by equipping it with a spark ignition, lowering the compression ratio, turbocharging, and adding an ahercooler and a parallel fuel induction system. Parallel induction provides two intake paths, one for hydrogen and one for air. It avoids intake-manifold backfiring by keeping the hydrogen and air separate until they enter the cylinder.

Jan 1, 1986

By G. J. Hasenfus

This paper presents the results of an extensive hydrological and geomechanical monitoring program which Gas conducted at a longwall coal mine in W. Va. The field program included monitoring of groundwater levels. overburden hydraulic conductivity, overburden movement, and surface subsidence relative to the passage of the longwall. Overburden geology and rock strength characteristics were evaluated prior to mining. A postmining corehole was drilled to evaluate main roof fracturing. An overburden response model is proposed based on the correlations between hydrological and geomechanical data.

Jan 1, 1988

By W. A. Ahrens, J. H. McNamara, J. G. Franek

"An economical, pollution-free process has been developed for the hydrometallurgical extraction of copper from sulphide ores. The extracted copper, in the form of cuprous chloride (CuC/), is converted by reduction to copper metal. The metal is melted and fire -refined into wire bars which meet the standards of electrolytic tough pitch (ETP) copper wirebars. IntroductionThe successful development of the Cyprus Copper Process has been an evolutionary series of events covering a time span of some nine years. The original process, based on an electrolytic membrane cell principle , was abandoned in 1975 because of technical, economic and pollution problems. During the past four years, the pilot plant has been reconstructed based on a new flowsheet and operated successfully in several campaigns, some for as long as four months. The pilot-plant hydro section operates at a 225-lblhr copper rate. In October 1977, a feasibility study was completed by Jacobs Engineering, Pasadena, California. The study showed favourable economic and technical feasibility. Jacob's studies in 1978-79 revealed favourable comparative economics with other known pyrohydro processes and favourable economies of scale.The Cyprus Copper Process converts copper concentrates of varying composition into copper metal, which has been proven to be equivalent in every way to electrolytic tough pitch copper, suitable for electrical applications. This is accomplished at capital and operating costs which are estimated to be lower than those associated with any other known currently applicable technology. Also, the total energy requirement is equal to or less than any other known process and the process is essentially pollution free."

Jan 1, 1980

By Ali Behrad Vakylabad, Esmaeel Darezereshki, Babak Koohestani

As a by-product of the steelmaking industry rich in iron and zinc, electric arc furnace dust (EAFD) landfill disposal is restricted in many countries due to the metal lixiviation risks. Several approaches have been examined to recycle or reuse EAFD. Hydrometallurgical methods mainly include the preparation of pregnant acid leached solution (PLS) using inorganic acids followed by selective metal recovery using different methods. We herein proposed a hydrometallurgical process initiated by acid leaching and finalized by thermal treatment to produce nano-ZnO from EAFD. At the condition of this study, only 67% of zinc was leached by sulfuric acid from EAFD into PLS while 98% of surplus leached iron was removed through precipitation by sodium hydroxide. Additional purification of iron removed PLS was accomplished using di-2 ethylhexyl phosphoric acid to extract Zn+2. The addition of ammonium hydroxide to purified PLS provided (Zn(OH)2)3(ZnSO4)(H2O)5 as the final precursor for nano-ZnO that ultimately transformed to nano-ZnO (60 ± 6 nm particle size) at 850 °C. The achieved results were scrutinized through various tests and analyses including TEM, XRD, SEM, EDS, FTIR, and TGA.

Mar 10, 2021

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By James K. Grunig, Rodney J. Anderson

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1983

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By Toshiaki Akahoshi

Keywords: Wasted catalyst, Hydrodesulfurization, Ammonium vanadate, Ammonium molyb-date, Hydrometallurgical process. The fundamental reactions have been investigated in order to develop a hydrometallurgical process for recovery of molybdenum and vanadium from wasted catalysts generated in the hy-drotreating desulfurization of heavy oil. The principal steps of the process are a mild oxidation roasting of the waste catalysts at temperature around 500°C, leaching of the target metal components with dilute ammoniacal aqueous leachates, selective precipitation of vanadic acid, and ammonium molybdate precipitation. The selective recovery of vanadium as vanadic acid is successfully performed using ammonium sulfate as a salting-out agent. Recovery of ammonium molybdate is based on large dependence of solubility of ammonium molybdate in ammoniacal solutions upon temperature and ammonium salt concentration. In this process, the solution after recovery of vanadium and molybdenum is recycled to the leaching stage of the roasted materials, and the ammonium salts in the process liquor is in the repeated use. Employment of am-moniacal system makes it possible to operate the roasting at much lower temperature than that for the currently operating process.

Jan 1, 2005

By J. H. McNamara

A process has been developed for the successful hydrometallurgical extraction of copper from sulfide ores. The extracted copper in the form of a salt is converted by reduction to copper metal. Purification of the metal is described which includes a description of the casting of ETP quality copper wire bars.

Jan 1, 1978

By T. Rigg, J. N. Stone

"The process described has been developed to utilize low-grade scrap -turnings, borings, tin cans and other types of ferrons scrap which currently has been of limited or no use in conventional steelmaking processes. If scrap of this type can be converted into high-purity iron by chemical means then there is a potential saving of several million tons of metal annually in North America.The process is chemically quite simple and consists of dissolving ferrons scrap in hydrochloric acid, followed by evaporation and crystallization of the resultant solution to yield ferrons chloride crystal.s. These crystals are dries, briquetted and converted to non sponge by reduction in hot hydrogen. The HCl produced from the reduction step. is absorbed in water and the hydrochloric acid so produced is returned to the dissolver circuit. The hydrogen produced from the initial dissolution of the scrap is used to reduce the ferrons chloride. Purity is maintained by bleeding off impure chloride solutions from the evaporator-crystallizer circuit, and converting these chlorides to oxides and HCI in a high-temperature spray roaster. The HCl produced in the roaster is absorbed in water and the hydrochloric acid returned to the dissolver."

Jan 1, 1970

By Kelly E. G

New Zealand suffers the disadvantage of widely scattered ore bodies, none of which is large enough to economically support its own smelter. This leads to the concept of a centrally located smelter which must be flexible enough to cope with var

Jan 1, 1980

By C. Lupi

In 1996 the Italian Agency for Environmental Protection (ANPA) has initiated a study of the environmental impact of the industrial sector of steel produced by Electric Arc Furnace (EAF). Within the framework of this study a hydrometallurgical process to treat EAF dusts was considered and developed. The paper describes the zinc and lead recovery from fumes coming from carbon steel production. The zinc extraction consists in acidic leaching followed by SX-EW steps. The leaching sludge containing lead sulfates was treated to obtain pure lead salt and inert solid residue. The whole process, that minimizes effluents by recycling the main liquid streams, has been developed to obtain marketable products. The solid waste, containing spinels, was subjected to elution tests in order to verify its compatibility with environmental regulation. The process, that has been set-up and tested in the laboratories of the University of Rome, will be transferred and studied on a pilot plant in order to assess its industrial and economical feasibility.

Jan 1, 1999

By Haydn H. Murray

A hydrothermal bentonite located in the high Sierras in Nevada is being mined and processed for use as a natural dietary supplement. Because hydrothermal clay deposits are normally zoned and not uniform in composition, a special stockpile was constructed to assure uniformity of processed products. The stockpile of clay was layered and rectangular in shape. Channel samples were taken from 10 locations around the stockpile and were mixed and quartered to provide representative samples. The samples were then chemically and mineralogically analyzed. The results showed excellent uniformity. The mineralogy and chemical analyses will be discussed in the paper.

Jan 1, 2005

By D. C. Seidel, E. F. Fitzhugh

Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types-the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of garnierite and related nickeliferous silicates are found.1 The garnierite veinlets are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass.

Jan 4, 1968

By J. A. Meech

"The technology known as Expert Systems is being used within the minerals industry in a wide variety of problem areas. Applications include diagnosis, prediction, training, monitoring and control. Expert Systems provide a way to program computers to imitate human thinking. The construction of such systems is a straight-forward task that can be quickly learned by novices but can require a lifetime to master.To assist in the understanding and utility of this technology, a special manual bas been prepared which operates on a microcomputer under the MS-Windows environment. The manual covers all aspects of Artificial Intelligence of relevance to Expert Systems. A hypertext system allows users to probe as d•~ply as needed to achieve understanding or to simply skim the surface of the knowledge to obtain a quick overview of subjects. The manual was developed under the sponsorship of the Mineral Sciences Laboratory of CANMET and is available from the Mining and Mineral Process Engineering Department at the University of British Columbia. Annual updates are planned to keep abreast of new developments in this rapidly changing technology. RESUMELa technologie: des Systèmes Experts est utilisée par l'industrie minière pour résoudre une grande variété de problèmes. Les domaines d'application comprennent le diagnostic, la prédiction, la formation, la surveillance et le contrôle des procèdes. Les Systèmes Experts permettent d'écrire des programmes d'ordinateur qui imitent le processus de la pensée humaine. La construction de tels systèmes e:st une tâche qui peut être apprise rapidement mais qui peut prendre des années à maitriser.Pour aider à mieux comprendre et utiliser cette technologie, un manuel spécial opérant sur microordinateur dans l'environnement Windows a été développe. Le manuel couvre tous les aspects de l'intelligence artificielle qui concement les Systèmes Experts. Un système ""hypertexte"" permet à l'utilisateur d'étudier un sujet en profondeur ou de simplement couvrir une grande variété de sujet en surface. Le manuel a été développe avec l'aide financière du Laboratoire des Sciences Minérales de CANMET et est disponible au Département de Génie Minier et Minéralurgique de l'Université de la Colombie Britannique. Des mises à jour annuelles sont prévues de manière à couvrir les changements et nouveautés de cette technologie en évolution."

Jan 1, 1993

By Thomas P. Meloy

"The presence of respirable quartz-bearing mineral par-ticles has been well documented in many coal mines, and the Mine Safety and Health Administration regulations address the quartz content of mine dusts. Unfortunately, the correlation between the quantity of respirable quartz-bearing mineral particles and the pathogenicity of the dust is not strong. Work is currently underway by the National Institute for Occupational Safety and Health/U.S. Bureau of Mines and work is being included in the Respirable Dust Center Program by Dr. Seehra to determine the surface availability of quartz in mixed composition mine dusts. However, this paper propose a possible source of surface quartz or a spe¬cial region in the coal that may contribute to the pathogenicity of selected particles in the respirable dust.Assumed in this model is the hypothesis that either the cleat surface is coated with quartz or some cytotoxic sub-stance that in the body is capable of destroying macrophage and thus inducing a fibrotic response (1) that during the frag¬mentation a reasonable proportion of the respirable size coal particles contain some of the original cleat surface and that these particles have the same order of in vivo cytotoxicity as do the quartz particles. It may be that these cleat surfaced respirable size particles are only contributory to the overall pathogenicity of the coal dust, nevertheless, there are enough of these particles to to considered as a potential source of the cytotoxic dust particles.This paper demonstrates that if the cleat surfaces are mineralized with quartz or have a pathogenic coating, then in many mines there will be enough respirable coal dust particles containing some cleat surface to cause a fibrotic reaction. To understand why some of the dust particles contain as part of their surface some of the cleat surface, consider what happens when a beer bottle is broken. While there are a large number of beer bottle fragments, many of the fragments, particularly the larger fragment sizes, will have as a fraction of their surface part of the original beer bottle surface. The model and mathematics of this problem have been worked out by Meloy.(2-4)In the homogeneous IAC model, (2-5) a fragment or par-ticle resulting from comminution is equally likely to occur anywhere in the material being broken. Therefore the probability of a particle of size x having part of the cleat surface in it, p(x), is proportional to x. Thus:"

Mar 1, 1989