Search Documents

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By Wayne F. Luinstra, Frédérique Vincent, André R. Laplante

"A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; possible uses are discussed. A case study of how the technology was used at Hemlo Gold Mines is presented.IntroductionUsing gravity to supplement either flotation or cyanidation is a well established practice in the gold industry. It differs from most recovery circuits in that most of the gold recovered by gravity would be recovered in any case by the circuit downstream, be it flotation or cyanidation. The economic justification of gravity is therefore based on small margins (for example. a net smelter return of gravity gold of 99%, as opposed to 94% by flotation). It was easily demonstrated when either flotation or cyanidation were relatively inefficient processes, and labour costs low (as gravity can be labour intensive). Over the past thirty years, the advent of better flotation machines (flash, column, high capacity), more effective collectors, and better control systems has increased flotation's metallurgical performance, thereby decreasing the incentive for gravity recovery. Cyanidation technology has undergone similar changes, with the advent of activated carbon, oxygen and lead nitrate addition, and improved impeller design.Today, gravity could remain an attractive option only inasmuch as it can be implemented with very low capital and operating costs. This has resulted in a relative shift away from gold gravity recovery (except for alluvial deposits), in the seventies and eighties. For example, as of the early nineties, gold gravity recovery has disappeared from the typical South African flow sheet. The advent of the Knelson Concentrator, at the beginning of the eighties, foreshadowed a resurgence of gravity recovery, as gold's grinding and classification behaviour (Banisi, Laplante and Marois, 1991) makes it possible to achieve adequate gold recoveries with very simple, Knelson based, gravity circuits (Laplante et al., 1994).Consider for example the Hemlo recovery circuit, made of a single 61 cm x 122 cm (2' x 4') screen, an automated 76 cm (30"") Knelson feeding a Gemeni table, to produce a 70-80% Au concentrate which accounts for approximately one fourth of the gold production (about 3 million grams per year). The low capital and operating costs make it possible to justify the gravity circuit on the basis of savings in other operating costs (e.g. fewer carbon stripping and reactivation cycles). Any improvements in recovery, which would at Hemlo be difficult to measure, would be additional benefits. Such a circuit is rapidly becoming a standard in Canadian and Australian operations.The justification for installing a gravity circuit must be first based on an estimate of how much gold it will recover (irrespective of what the potential benefits are). This is a function of the nature of the gravity circuit to be installed; however, Knelson circuits, by their very simplicity and efficiency, limit the options. This leaves the amenability of the ore to gravity recovery as the single most important parameter. Various approaches can be used to characterize this response (Woodcock, 1993). The present work sought a route which would fulfil the following criteria:"

Jan 1, 1996

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemicals are added to flotation circuits directly and indirectly to control issues such as scaling and dust in other areas of the operations. Since dosage levels are generally not high, a standard laboratory float test may not be able to determine the effect of a specific chemical on the productivity of the flotation circuit. This paper presents a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5–100 g/t). Results indicate that this protocol helps to predict potential interference by a particular chemistry on the flotation circuit.RÉSUMÉ Certains produits chimiques ne servant pas à la flottation sont ajoutés directement et indirectement aux circuits de flottation afin de contrôler des problèmes tels que l’entartage et la poussière dans d’autres secteurs des opérations. Étant donné que les niveaux de dosage sont généralement faibles, un essai standard de flottation en laboratoire pourrait ne pas être en mesure de déterminer l’effet d’un produit chimique spécifique sur la productivité du circuit de flottation. Le présent article définit une procédure d’essai en laboratoire qui utilise des études cinétiques de flottation pour vérifier l’effet de doses normales à extrêmes de produits chimiques antitartre et anti-poussière (5 à 100 g/t). Les résultats indiquent que ce protocole aide à prédire l’interférence potentielle d’un produit chimique particulier sur le circuit de flottation."

Jan 1, 2016

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By M. F. Dawson, S. B. Davis

SYNOPSIS This paper describes the size reduction of limestone smaller than 1 mm by attrition grinding, using quartz (1 to 3 mm) as the grinding medium in a laboratory rig. The ore and grinding medium were closely sized fractions, and the particle size of the grinding medium was at least three sizes larger than that of the ore. Batch tests showed that the size reduction of the feed followed two first-order rate processes: one for an apparently fast-breaking ore fraction, and a slower one for most of the ore (86 per cent). The production of fines (material smaller than 10 µm) followed a zero-order rate equation. Continuous runs showed that the process could be modelled as a perfectly mixed system provided that the discharge screen did not selectively retain coarser particles of ore. The ratio of medium to ore (both by mass and by volume) was found to have a significant effect, the most energy¬efficient grinding occurring at ratios between 1 and 2. The solids content of the slurry also had a significant effect, the greatest efficiency being obtained at 50 to 65 per cent solids (by mass). Within these energy-efficient ranges of medium-to-ore and solids content, the lower values resulted in maximum feed breakage and the higher values in maximum fines production. The most important factor in the breakage of feed was the difference in the particle size of the grinding medium and the ore; the amount of ore broken out of the feed size for a given energy input was found to increase linearly with the difference between the size of the grinding medium and that of the ore up to 2 mm. The production of fines increased similarly, but only up to a difference of about 1,2 mm, when it levelled off at about 5 kg/kW ? h. The mechanism proposed for attritioning is mainly the abrasion of 1 µm planes of limestone along the crystal axes, with some fracturing along existing lines of weakness. The energy consumption of nearly 200 kW ? h per ton of product smaller than 10 µm appears to be higher than that in other types of milling. It is concluded that the value of attrition milling lies in its selectivity; in this work, only the softer limestone and virtually none of the hard quartz grinding medium was comminuted.

Jan 1, 1989

By P D. Katsabanis

Explosives malfunction due to shock waves is a serious concern for successful blasting results. Malfunction includes sympathetic detonation and desensitization of explosive charges as well as the modification of firing times of conventional pyrotechnic detonators.

Jan 1, 1995

A sample of tailings from a local, low grade (less than 2g/t) tailings dump was investigated for gold recovery. The tailings were very fine, with 90 per cent passing 30¦m and almost 60 per cent passing 10¦m. Tabling the coarse product from classification using a cyclone proved unsuccessful, with low recoveries being obtained due to high gold losses in the slime streams. Gold recovery by cyanide leaching was quite rapid, with recoveries of 85-90% being obtained in five hours. Lime and cyanide consumptions were 3 g/t and 0.1 kg/t respectively. Gold loading onto carbon was inhbited by the presence of the large amount of fines, so heap and vat leaching should be considered where the gold is recovered from a clear pregnant solution. Settling tests were conducted on tailings. It was observed that the addition of at least 3 kg/t lime or 0.4 kgh nonionic flocculant was necessary to promote settling of the tailings to generate a clear supernatant for gold and water recovery.

Jan 1, 1991

By Bjorn N. P. Paulsson

A number of granitic rock specimens have been studied from the Stripa mine site in connection with a large-scale geomechanics research program. The purpose of the program was to evaluate and develop field and laboratory techniques for rock mass characterization and to determine design parameters for storage of nuclear waste. In this paper a minicomputer-based technique for studying dynamic rock properties in the laboratory is described, together with results from the tests. The specimens were tested under different uniaxial and saturation conditions. Specimens from a field-heated rock mass were also tested to determine if temperatures typical of those encountered with nuclear waste would introduce additional fracturing. Both Vp and Vs increased with stress for both saturated and dry specimens. Both Vp and Vs were higher for saturated specimens at all stress levels compared with the dry. The velocities increased linearly or near linearly with saturation. The test results on the previously heated samples indicate that attenuation is more sensitive to thermally-induced microfracturing than velocities. Analysis of the attenuation values with stress show that rock heated to 200°C is damaged, and that the damage is in form of low-aspect ratio fractures.

Jan 1, 1984

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

By Vutukuri VS, Budavari S

During recent years many investigators have suggested large spacing to burden ratios to improve the fragmentation obtained in blasting. In spite of these suggestions, most operators still use a conventional ratio of 1 to 2. From single hole longitudinal charge tests in laboratory, it is shown that burden controls the fragmentation. The burden for obtaining uniform fragmentation is smaller than the burden to obtain maximum breakage. Tests on two or three holes show that a larger spacing to burden ratio can be used for smaller burdens, but it is not possible for the larger burdens chosen to obtain maximum breakage. By using finite element analysis evidence is presented to show the effect of spacing and burden relationship on blasting results.

Jan 1, 1975

By P. R. A. Andrews

"A sample of flotation feed from Bakertalc Inc., High water, Quebec was subjected to flotation evaluation to improve the recovery of talc. A number of alternative frother/collectors and depressants as well as flotation parameters including pH, conditioning time, frother/collector concentration and pulp density were assessed. In addition, the possibility of using a size coarser than that currently employed for flotation (95% minus 50 um) was investigated.As far as possible, a laboratory duplication of the present circuit arrangement was folio wed so as to minimize the cost of any changes. The best results obtained were a concentrate analyzing 95.96% acid insol for a recovery of 65.98% after four stages of cleaning. With recirculation of cleaner tailings, the recovery would be higher.The possibility of using an alternative method, based on the natural ability of talc to float unaided by a frother/collector, was briefly explored with encouraging results.IntroductionBakertalc lnc ., located in the eastern townships at Highwater, Quebec, Is approximately 140 km east of Montreal near the Vermont, U.S. border. Originally called Baker Mining and Milling Co. Ltd., it has produced pulverized talc products since 1938(1 ), although records show that talc was mined in the area as early as 1871(2). Feed to the mill originally was obtained from local deposits, but since 1952 the van Reet mine near south Bolton, approximately 25 km from Highwater, has been the source of ore .In 1957 a Raymond high -side roller mill was installed which enabled production of a greater range of talc products and, in 1960, new crushing equipment and a dryer were added. Other additions to the mill were the introduction of wet magnetic separation, although this was later discontinued, and flotation to produce high-grade talc concentrates."

Jan 1, 1985

By A. V. Pegler

As with most rheologically defined materials, rocks react differently in different environments to similar forces. Physical changes and deformations depend as much on the rate of change of stress as the magnitude of stress. In many instances the rate of change is more important. Under load, all real materials will flow if given time. If there is no time for flow, materials tend to react in a brittle manner. Particular characteristics are developed in rocks during their periods of formation and postformative geologic history. Whatever their mode of occurrence, rocks are a record of their formation and changes. Where analyses are possible, advantage should be taken of the natural inherent characteristics to help design economical functional structures. A number of techniques of measurement and analysis have been developed. The fracturing of rock by hydraulic pressure has been examined by many authorities but few within the scope of available published literature have used the actual rocks concerned in tests to examine directional characteristics or preferred strain propagation rates and directions. In a number of investigations of the properties of rocks for mine design purposes and stress analysis problems in which the writer has been associated, it has been demonstrated that there are definable preferred shear planes in most rocks. Preferred shear planes can be identified by a photoelastic method of analysis, and the information can be used to improve design of optimum drilling and breaking directions for mining purposes. Definable principal strain directions can be determined to facilitate design directions of optimum stability for permanent mine openings. In field fracturing operations the same directional characteristics as outlined above should be used to define preferred fracturing directions as in the laboratory from oriented samples. It is mainly with this aim that

Jan 1, 1968

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

Sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. The pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors and it was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of the shape factor values with the amount of water used for granulation is discussed in relation to the strength of granules of the sinter mixes.

Jan 1, 1984

By Damien Wagner

To reduce the emission of greenhouse gases by the steel industry, particularly for ironmaking, the production of DRI (Direct Reduced Iron) using hydrogen as the reducing gas instead of carbon monoxide is being considered. In this context, the reduction of pure hematite by hydrogen was studied at the laboratory scale, varying the experimental conditions and observing the rate and the course of the reaction. All the reduction experiments were performed in a thermobalance and supplementary characterization methods were used like scanning and transmission electron microscopy, X-ray diffraction, and Mössbauer spectrometry. The influence of rising temperature in the range 550-900°C is to accelerate the reaction; no slowing down was observed, contrary to some literature conclusions. A series of experiments consisted in interrupting the runs before complete conversion, thus enabling the characterization of partially reduced samples. Interpretation confirms the occurrence of three successive and rather separate reduction steps, through magnetite and wustite to iron, and illustrates a clear structural evolution of the samples. Finally, the influence of the sample type was revealed comparing a regular powder, a nanopowder and a sintered sample. The regular powder proved to be the most reactive despite its larger grain size, due to a more porous final structure.

Jan 1, 2006

By Eung Ha Cho, Olufemi Olajide

A laboratory study of dense-medium cycloning with Redstone seam coal has been conducted. The investigation was performed using a 203 mm (8 inch) Heyl-Patterson dense-medium cyclone. Two underflow orifices of 31.8 mm (1.25 inch) and 44.5 mm (1.75 inch) in diam were used. The effects of feed pressure and particle size were determined on the cycloning performance. In addition, the cyclone performances with coal-rich and refuse-rich samples were also investigated. The results of the experiments were analyzed using basic hydrodynamic principles. The increase in the feed pressure increases the specific gravity of separation (defined as the specific gravity of a particle which has an equal chance of reporting to either the overflow or underfow) for both underfow orifices. The specific gravity of separation increases as the particle size decreases with the smaller underflow orifice. However, an opposite relationship has been observed with the larger under flow orifice. The separation becomes sharper with the smaller under flow orifice than with the larger underflow orifice especially for fine material. Also, the separation becomes sharper with an increased feed pressure for a coal-rich sample. However, this effect is less significant for a refuse-rich sample. This means that a high feed pressure is required for a coal-rich sample to maintain a good separation. It also means that applying a high feed pressure provides a good separation regardless of the type of feed coal in terms of ash content in the solid.

Jan 1, 1990

By Po-Wei Tun, Kuen-Yuh Wu, Tso-Min Shih, Hsi-Chiang Fang

The purpose of this study is to investgate the coal dust explosion characteristics and to search for the prevention methods of the coal dust explosion as well as the propagation of the explosion flame of the middle-bearing coal formation in Taiwan by an open type coal dust explosion apparatus in laboratory. The coal samples were taken from the typical middle-bearing formations of the Sam-Ming,Tai-Ho and Lee-Fong coal mines The rock dusts, the free water mixture with coal dust samples and the interval clean out the coal dust in the testing chambers were applied for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1993

By B. Anameric, S. K. Kawatra

Pig iron nuggets were produced in a laboratory scale furnace at Michigan Technological University. These nuggets are produced from pellets consisting of a mixture of iron oxide, coal, flux, and a binder, which are heated to 1450°C.These pellets then self-reduce to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate slag phase forms that cleanly separates from the metal. The physical and chemical properties of the pig iron nuggets are similar to pig iron produced by blast furnaces, which is distinct from Direct Reduced Iron (DRI).

Jan 1, 2004

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934

By K. V. Raj

As open pit mines continues to grow deeper, managing air pollution can become challenging. During arctic air inversion, the temperature of the air over the mine increases with altitude, and the cold, heavy, surface air is trapped in the pit. This problem is complex, and any solution will require an extensive understanding of the interactions between the aerodynamic movement of air, air inversion, meteorology, pollutant sources, and transport phenomena in the open pit mines. The availability of computational fluid dynamics (CFD) has elucidated the pollutant flow mechanism in open pit mines. Very few CFD studies have been published, especially the Large Eddy Simulation (LES), on the contaminant transport in deep open pit mines under arctic air inversion. The contaminant transport in an open pit mine under arctic inversion is due to a stable or nocturnal boundary layer in micro-meteorological terms. Understanding the physics of the stable boundary layer (SBL) is relevant to air flow and pollutant transport in deep open pit mines. This paper focuses on a Large Eddy Simulation (WMLES as Sub-Grid Scale Model) modeling of the SBL and pollutant transport in a large open pit mine.

Feb 23, 2014