Search Documents

By E. F. Schnitzer, C. Lidstone, D. Cramer, P. J. Wampler

The River Island mining site is located at approximately river mile (RM) 15 on the Clackamas River, a large gravel-bed river in northwest Oregon. During major flooding in February 1996, rapid channel change occurred. The natural process of meander cutoff, slowed for several years by dike construction, was accelerated by erosion into gravel extraction ponds on the inside of a meander bend during the flood. In a matter of hours, the river cut off a meander and began flowing through a series of gravel pits located on the inside of the meander bend. The cutoff resulted in a reduction in reach length of approximately 1,100 m. Erosion by bed lowering, knick point retreat and lateral erosion of upstream river banks occurred quickly. Within two days of the peak flow, 3.5 hectares of land and 105,500 m3 of gravel were eroded from the river bank just above the cutoff location. Much of this gravel moved a short distance downstream into the excavation. Reach slope increased from 0.0022 to approximately 0.0035 in the cutoff reach. Between 1996 and 2003, the knick point from the meander cutoff has migrated 2,290 m upstream, resulting in increased bed load transport, incision, and local lowering of the water table. In 1993, prior to the meander cutoff, transects were surveyed in the River Island reach upstream of the cutoff location. Resurvey of these transects and aerial photo analysis indicates that 96% of the knick point migration occurred during the first winter following meander cutoff. Connection of the flowing river to the off-channel ponds has had minimal effect on water temperatures in the mainstem Clackamas River. It is likely that this minimal change in temperature will decrease as ponds are isolated from active river flow by gravel bar deposition. Fish net-ting in spring 2002, suggests that salmonid use of the pond in the spring is minimal. The most abundant native species netted were large-scale sucker and northern pikeminnow. The most abundant non-native species netted was brown bullhead. Early regulation by state and federal agencies did not adequately evaluate potential impacts to the river and the floodplain; nor did it evaluate future impacts related to geomorphic processes and sediment transport. New permit evaluation methods, currently implemented by both Oregon and Washington, incorporate 1) river dynamism through historic river migration analysis; 2) stability of human structures in light of river dynamics; and 3) sediment transport and its impact on channel stability and dynamics. The gravel pit capture at River Island highlights the potential risks of mining in an active secondary channel of a large gravel-bed river. Mining deeper than the depth of the adjacent channel, within the active migration zone, may increase off-site impacts. In locations where multiple gravel excavations are present within the meander zone, a comprehensive reclamation and restoration plan should be developed which provides long-term channel stability within the natural variability of the entire river reach.

Jan 1, 2006

By Gregory P. Cole, Peter G. Kovalchika, Rudy J. Matetic, Adam K. Smith

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/nonmetal miners had a hearing impairment by age 501. Mine workers are exposed to additional noise levels underground due to the reflection of machine generated noise that would otherwise dissipate in an above ground setting. Determining the sound absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed, rather than reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of some of the materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes: a finite room, a diffuse field, and relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper will present a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients will be essential for determining and predicting potential overexposure to machine operators in different mine environments.

ON milling plants, where a large number of slime samples are collected each day, considerable work is involved preparing them for the assayer. The usual practice (as the material usually passes a 150-mesh screen) is to place the sample on a 30-mesh screen an 1 brush it through on to a cloth below. The sample on the cloth is mixed and a portion taken out for the assayer. A simple apparatus that would rapidly disintegrate and prepare these slime samples for the assayer was needed. The manufacturers of assayers' supplies appear to have overlooked apparatus for this class of work. To overcome the tedious preparation of slime samples by the above method, the writer devised the apparatus shown in the accompanying drawing (Fig. 1). It will be seen that the apparatus is a combination of a modified household flour sifter and a riffle sampler.The apparatus is made up in two parts, the top half consisting of a screen box carrying the disintegrator, and the bottom half a, riffle divider, the joints between the two being a slip-in fit. A lid is provided for the screen box. The disintegrator consists of an open drum, to which are soldered three rows of spring steel fingers. Each row has a number of steel fingers which, on rotation, press against the semi-circular screen in the screen box, forcing the slime particles through.To operate the apparatus an 8-in. sample tin is placed under each spout of the divider. The sample of slime, which is about 2 lb. in weight and usually in lumps, is placed in the screen box, the cover replaced, and the drum rotated about half-a-dozen times by means of the handle.The disintegrated sample is divided by the rifle divider into two portions, which are found in the tins under the spouts of the apparatus. One of these samples is taken, mixed on a sheet, and sent to the assayer.

Jan 1, 1922

By Pharis E. Williams

The ability of voids, microballoons, and even solids to sensitize explosives has been known and used for many years. This phenomenon has generally been studied and reported under the terminology of "hot spots" because of the increase in local pressure and temperature when a shock wave encounters such sensitizers. A method for treating this phenomenon in detonation theory or in a detonation model has been studied for almost the same length of time. Perhaps because of the complexity and non-linearity of the void, or microballoon collapse, several of these studies have used the expediency of including additional terms in the burn rate law to account for the influence of hot spots. The detonation model proposed here considers the sensitization due to discontinuities in the shock impedance to be a mechanical phenomenon to be accounted for in the mechanical equations governing the detonation and not in the burn rate law. While this is not a new contention, the method for handling this non-linear phenomenon within the proposed model is new. The model also includes a method which accounts for the manufacturing variables of emulsion matrix cell size, microballoon size and type, as well as energetic additives.

Jan 1, 1992

By M. Ashraf Mahtab

In Louisiana salt mines a sudden erruption or outburst of salt and gas occurs when the heading face approaches a pressure pocket (altered salt with high pressure gas). The resulting cavity is semi-ellipsoidal, reaching lengths of 50m or more. Potential risks from the outbursts include loss of life and equipment. A gas outburst is initiated by "disking" of the salt in biaxial compression and propagates by spalling of the cavity walls and further disking. The outburst is terminated by a combination of dilatancy hardening, increase in stress along the cavity axis, and enlargement to boundaries of the pressure pocket.

Jan 1, 1982

By H Austrheim, A K. Engvik, A Putnis

How aqueous fluids move through rocks and minerals is a question of possible pathways and mechanisms. Existing pathways such as fractures and grain or mineral boundaries provide obvious channels for fluid movement. We show how minerals reactive in the presence of an interfacial fluid can be replaced by new product phases through a process of interface-coupled dissolution-reprecipitation. A resulting porosity in the new phase provides a new pathway for fluid movement and therefore mass transport through the mineral, which progressively reacts at a moving interface. Eventually fluids of new and changing composition can pass through originally solid minerals and move on further, taking remobilised elements with them, to be reprecipitated whenever the chemical and/or physical conditions allow. One such example is albitisation of rocks associated with mineralisation.

Jan 1, 2008

By William H. Dresher

A study has been made of the reaction mechanisms occurring during the salt-roast process to form water-soluble sodium vanadate compounds from the vanadium oxide compounds present in vanadium-bearing ores and concentrates. Two reactions have been identified, either of which lead to water-soluble compounds--oxidation of sodium chloride by water vapor and. oxidation of sodium chloride by oxygen. The former reaction has been found to be predominant in the salt-roast process. A kinetic treatment of the data has shown that for the formation of sodium metavanadate the rate-controlling step in the reaction, in which sodium chloride is oxidized by water vapor is the decomposition of a species containing water and sodiumm chloride, on the surface at the gas-solid interface. For the formation of sodium pyrovanadate, the rate-controlling step is the decomposition of a species containing water and sodium metavaradate on the surface. The transportation of water through the system, perhaps as a sodium chloride-water complex or a sodium metavanadate-water complex, and the actual chemical reaction are relatively fast compared to the initial surface decomposition step. A similar treatment on the data for the oxidation, of sodium chloride by oxygen has shown that the rate-controlling step, is the actual transportation of oxygen from the gas-solid interface to the reactive site. This transportation is by a sequence of two diffusion processes. Transportation during the early stages of the reaction is by the diffusion of oxygen through a continuous layer of reaction product. After, the first few minutes of reaction time a second diffusion process begins and is continuous for the remainder of the reaction. This second diffusion process involves the diffusion of oxygen, through a layer of reaction product that has developed voids around which the oxygen must diffuse. The hindering, nature of this latter process causes the rate of transportation of oxygen to the reaction site to be considerably slower than by the simple diffusion mechanism initially followed. A thermodynamic treatment of the data has shown that the energy of activation for the decomposition of the water-sodium chloride species on the surface is -12.1 Kcal. per mole. For the decomposition of the water-sodium metavanadate species on the surface' the energy of activation is -15.1 Kcal. per mole. The results of this study indicate the limiting mechanisms of the basic reactions occurring during the salt-roast process. These results suggest what variables should be examined in applying this information to actual plant operations.

Jan 1, 1961

By P. Condori

In spite of the importance of the slurry transport and discharge in autogenous and semiautogen-ous (AG/SAG) mills, it is evident that a more comprehensive and useful model is still required. Semi-empirical models used up to now have many limitations and cannot be used beyond the ranges in which they were developed. The breakage of particles as they are transported along a mill com-plicates the experimental analysis and the modelling of the transport process within the mill. The interaction of the grate discharge and the pulp lifters, with the added issue of backflow from the pulp chamber into the mill, makes the discharge modelling process difficult. In order to overcome these difficulties, a mechanistic approach has been applied. The general transport and discharge model was subdivided into four independent models: Flow through the charge, flow through the grate, flow in the pulp lifter, and flow-back. This paper gives an overall description of the modelling approach and discusses in particular the modelling of transport of fluids through the charge. In order to evaluate and calibrate the model, experimental work was carried out. To evaluate the gradient pressure under different conditions of charge packing and flow rate, a specialised experimental rig with a highly sensitive pressure gauge was used. Preliminary results identify the differences of the charge and grate on the restriction of flow. The existence of a dynamic voidage in our particular system was more evident and as a result, a semi-empirical correlation for the voidage was developed. In general, results show that the me-chanistic model derived from Ergun?s equation for flow through a packed bed can be satisfactorily adapted.

Jan 1, 2014

By Elbasher M. E. Ahmed, Indresan Govender

"A mechanistic model of axial charge segregation in rotating drums is presented. We show that granular material composed of different frictional properties diffuse into axial bands as a consequence of concentration fluctuations in the free surface layer that is caused by friction-limited mobility. A Bagnoldian stress assumption ensures an asymmetric free surface profile thereby providing the essential ingredients for the evolution of axial bands and the subsequent band coarsening observed in the literature. The formulation is sensitive to the boundary conditions of tumbling mills, including particle size and density, mill speed, inter-particle bulk friction, end wall friction and drum geometry (length and diameter).INTRODUCTIONA mechanism to fully describe the axial segregation of charge in a rotating drum remains elusive to the mineral processing industry. With regard to low aspect ratio mills (like ball mills), current thinking favours the use of closed circuit mills with correspondingly low residence times to offset the completely random contact probabilities between particles and balls (Wills & Napier-Munn, 2006). Conical end caps are argued to exploit the centrifugal force to achieve a regular gradation of ball size along the mill with larger sizes at the feed end and smaller ones closer to the discharge. However; segregation along the length has been observed in the absence of conical end caps (Oyama, 1939; Levine, 1999): In these investigations, sufficient differences in the particle’s mechanical properties (particle size, density, shape, surface roughness) was enough to successfully achieve axial segregation. Figure 1 shows the segregation of a bimodal distribution (by size) into bands of larger (darker colour) and smaller (lighter colour) particles."

Jan 1, 2016

A Mechanistic Model of Batch Grinding in Ball Mills

Sep 13, 2010

By Rodrigo Carvalho, Marcelo Tavares

"The accurate prediction of the outcomes in SAG grinding has been a great challenge to researchers and process operators. The use of Discrete Element Methods for modelling charge motion in tumbling mills allowed extraction of not only visual data, such as the position of the charge, but also the energy transfer in terms of the energy dissipated in the collisions. One of the advantages of DEM technique is its scalability to different mill sizes and some operational conditions such as speed and mill filling. Recently the Authors proposed the coupling between DEM outputs and modified Population Balance Models that with proper dedicated ore characterization tests allows the prediction of the outcomes of an energy transfer example. This modelling framework is called the Multi-scale Mechanistic Modelling. This paper shows the application of the Multi-scale Mechanistic Model to a set of pilot plant tests ran at different operational conditions. The prediction of the grinding outcomes and even the stabilization of the charge was achieved by the use of the Multi-scale Mechanistic Modelling framework. This approach has a great potential to become a powerful tool to design and optimize AG and SAG mills."

Jan 1, 2014

By Masakazu Niinae, Tasuma Suzuki, Mai Moribe, Yohhei Okabe

Bench-scale electrokinetic experiments were performed to elucidate the electrokinetic remediation mechanisms of arsenate from artificially contaminated kaolinite. The electrokinetic experiments in which a constant voltage was applied demonstrated that high soil pH favored arsenate remediation with respect to both the remediation time and electricity consumption. It was also demonstrated that applying a pulse voltage (1 hour ON, 1 hour OFF) significantly improved the electricity consumption efficiency when the soil pH was maintained at the initial value during the experiments; this trend was not observed when the soil pH was gradually increased from the cathode side. These electrokinetic experimental results indicate that the remediation rate-limiting step varied with soil pH. When the soil pH was maintained at the initial value of 7.2 during the experiments, arsenate desorption was the remediation rate-limiting step rather than the migration of dissolved arsenate toward the anode. Conversely, when the cathode pH was not controlled and the soil pH was correspondingly increased gradually from the cathode side, the migration of hydroxyl and desorbed arsenate ions toward the anode played a more important role in the control of the overall remediation efficiency.

Jan 1, 2014

By P. Valicek, M. Farren, G. Harrison, G. van den Berg, P. van Dorssen, P. Kramers

Full mechanization of the stoping operation using rockbreaking methods other than blasting has been a target of research for decades because of the considerable payoffs in terms of increased face advance rates, productivity and safety. However, the unavailability of economically viable rock breaking tools has prevented progress so far. This has changed with the invention of activated cutting tools, which achieve significantly reduced operating forces, power consumption and wear compared to non-activated tools and thereby permitted the development and evaluation of the first mining system using this technology. Targets for the mining system were a face advance of 100 metres per month on a double shift basis for a 30 metre long panel and eventually fully automated man-free stoping. The purpose of this paper is to describe the design, development and evaluation of the mining system. This was a major collaborative effort between Anglo Platinum’s Rustenburg Platinum Mines Rustenburg Section — Townlands Business Area, Anglo Platinum’s Research and Development Department within the Mining Technology Division, the inventor of the technology Bechem GmbH, the equipment manufacturers Long-Airdox Ltd and Zollern GmbH, and CSIR Miningtek who managed the project. A structured process was followed during the development to minimize the risks involved in using such leading edge technology. The system was rigorously evaluated to ascertain the economic viability of the method and to collect data for the design of a production system.

Sep 1, 2001

By Cheng Ang, Yun Bai, Zhi Liu

"This paper presents a conceptual design of an innovative tunnelling method named the Ring Pipe Jacking Method (RPJ) which is conducted by the Ring Pipe Jacking Machine (RPJM). The RPJM consists of a double ring shell which forms a ring section where small interlaced cutter heads or several micro tunnelling machines are assembled to cut soil. Similar to the conventional pipe jacking method, the RPJM also needs a thrust system, a slurry transport system, and a control system. To satisfy the need for large/super large or special section tunnels in future, the RPJM is designed to reduce sharply the excavation face to the annular section, thus enhancing the face stability. Part of the innovation is that the RPJM uses modular cutter heads or micro-TBMs which can be reused. The typical double shield shape can be easily changed by reinstalling the modular cutter heads. Modularity allows the tunnel to be cut in any cross-section shapes, ranging from a circular tunnel to a rectangular one. INTRODUCTION The demand and requirement to utilize urban underground space is rising with the rapid social development in recent years. It is necessary to reduce excavations of the urban ground surface to ensure smooth traffic in cities. Therefore the conventional open cut construction method for underground tunnels can no longer satisfy the need of practical engineering, and it is taken over by trenchless technologies .The Pipe jacking method is an important trenchless technology and is used more and more frequently to install underground pipelines, but the present pipe jacking method still has many problems. For example, it is not suitable for installing large-diameter tunnels and it also has difficulty in construction of short radius curved tunnels. This paper presents a conceptual design of an innovative pipe jacking machine named the Ring Pipe Jacking machine (RPJM) and introduces the correspondent Ring Pipe Jacking Method (RPJ) which can be applied to construct large-diameter tunnels. Furthermore, technical characteristics and superiority of the ring pipe jacking method are analyzed in this paper."

Jan 1, 2016

By Larry G. Stolarczyk

An underground medium frequency radio communications system has been developed and demonstrated in both coal and metal/non metal mines. The principal advantage of the system are its low cost, ease of installation and the ability to provide radio communications to any vehicle or roving miner in the underground mine. The system provides high quality radio coverage in work areas and along manways with existing "wireplant" conductors. The conductors include AC power cable, telephone cable, metal water and high pressure air pipes, etc. The measured communications range from the base station to mobile transceiver exceeded 12,500 ft without the use of repeaters. A cost/benefit analysis shows that the initial cost of the equipment can be returned 2-6 times in the first year. The mine productivity increases by approx. 13 percent.

By Larry G. Stolarczyk

This report deals with information regarding a new Medium Frequency (MF) Wireless Communication System for underground mines. This new telecommunication system works on low loss electromagnetic wave propagation modes which allow it to provide quality radio communications almost anywhere in a mine. Tests show the MF system can provide improved safety and managerial control, increased productivity, better organizational team-work and reduced maintenance cost; furthermore, MF's unique design allows for easy installation at a minimum cost. This paper covers the following: 1) MF design plan, 2) Overview of mine radio communications systems, 3) Preparations needed for designing an MF system, 4) MF equipment, 5) MF installation, 6) MF design considerations, 7) MF design specifica¬tions, and 8) Recommendations dealing with MF system. Experiments in four mines are illustrated to demonstrate the success and via¬bility of the MF system. The mines range from small (500 tons/day) to large (67,000 tons/day) capacity and represent several different mining methods. The MF Wireless Communication System represents an advancement in mining communication and the groundwork for other advanced mine systems.

Jan 9, 1984

By Thaís Ferreira Marks Brasil Duque

O equipamento utilizado na medição do CWI de Bond também mede uma estimativa da energia de fratura das partículas de amostras de rochas e minérios. Esta medida só pode ser considerada uma estimativa da energia de fratura se, durante o ensaio, o material não é danificado. Em função do procedimento do ensaio de CWI, é possível que as partículas sejam danificadas por impactos sucessivos dos martelos em energias de impacto crescentes. Se houver danificação, a estimativa da energia de fratura será menor do que a energia de fratura real do material. Caso contrário a energia de fratura medida corresponde a energia de fratura mais a energia equivalente a um incremento de 5º do ângulo de impacto. Neste trabalho uma metodologia foi desenvolvida especificamente para avaliar a danificação de partículas de rochas durante o ensaio de CWI. Quatro amostras distintas de rochas/minérios foram testadas. Os resultados mostram que há uma tendência consistente indicando que a danificação ocorre, porém, se de fato as partículas danificam, a magnitude da redução da energia de fratura é baixa ou incipiente.

Aug 17, 2017

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021

By JIACHENG XIE, XUEWEN WANG, QINGBAO BAO, ZEWEN YAN

The general application of memory cutting technology to shearers is improving the intelligence of the working face, but it has its limitations. It is only suitable for conditions where the environment of coal seam is changing slowly. It compensates for the cutting height by changing the fuselage attitude, and frequently adjusts the height to control the learning cutting trajectory, but due to the problems of shearer control and height adjustment accuracy, it cannot adapt to and compensate for the change of cutting height in a timely manner, resulting in poor cutting accuracy. This study puts forward a virtual memory cutting method based on prediction of the shape of the armored face conveyor (AFC). The integrated key technologies include generation of virtual teaching cutting curve, height adjustment strategy of front and rear drums, cutting

By Harper F

This paper outlines the authors' views of the methodologies which can be employed to value mineral properties at different stages of development for the purposes of project financing, mergers and public floats. This paper discusses the key issues in Discounted Cash Flow (DCF) analysis including the importance of data verification and the shortcomings in DCF analysis. Stockmarket valuation measures and valuation methodology for exploration and pre development projects are examined through examples and pitfalls are identified. The use of valuations in corporate transactions and their strategic value is also discussed.

Jan 1, 1994