Search Documents

By Charles Macdonald

WROUGHT-IRON eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this methpd of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

The ore body being worked is about one hundred feet in length by seventy feet in width. A face of about fifteen feet is stoped over the whole level at one operation, this height standing without any timber.Double lines of logs, twenty feet in length and from ten inches to one foot in thickness at the small end, are then laid longitudinally, butt to butt, and breaking joint from end to end of the ore body they are at ten feet centres from wall to wall. The starting logs are single for the first ten feet and their ends are hitched into the solid rock. These are called "miners" and are the logs which are picked up as the level underneath is worked up. The double layer gives a better chance of picking up. Logs are now laid from the centre of the ore body at right angles to the miners, the ends being hitched into the walls. A space, seven feet wide, is left open right through the centre of the ore body...

Jan 1, 1904

By František Molnar, Zsolt Szentirmai, Juraj Schmiedl, Felix Sekula

"Hydrometallurgical nickel production in Sered Nickel Plant (Slovakia) that treated roasted Albanian ore left behind a considerable amount of the solid leaching residue. About 6 million tons of this fine-powder residue containing approximately 52 wt.% of iron in the form of oxides is to the present day stored in a stockpile. However, its iron content makes it a potentially interesting secondary raw material for iron production. This secondary raw material is not, unfortunately, suitable for direct treatment in iron and steelmaking processes.This paper presents results of the laboratory tests of pyrometallurgical method of processing of the leaching residue by its roasting and subsequent refining melting. The objective of the selective reducing agglomeration roasting was to reduce iron oxides and to simultaneously avoid reduction of chromium oxides and silica. Refining melting is carried out in an inert atmosphere. The products of melting are technically pure iron and slag.IntroductionThe leaching residue stockpiled on waste dump near already non-existing Nickel Plant Sered, Slovakia, is considered to be one of the most important environmental burdens in this country. The 40-years of an on-going effort focused on finding the methods for extracting metals and thus remove the waste dump have not been successful [1,4,5,6]. From the literature survey it is evident that past investigations have been following three main routes:1.Removal of chromium by mineral processing methods prior to its metallurgical treatment to achieve final chromium concentrations below 0.3 wt.%.2.Pelletization of solid leaching residue and its subsequent reduction in blast furnace and steelmaking plant and simultaneous removal of chromium.3.Pelletization of solid leaching residue followed by metallurgical processing of preliminary reduced semi-product in electric arc furnace (EAF) accompanied by partial reduction of chromium."

Jan 1, 2008

By J. A. H. Church

My paper entitled "Spontaneous Combustion of Coal in Mines;" read some time ago before this Branch, consisted chiefly of extracts from the British Blue Book dealing with the same subject. Fallowing my article, Mr. de Hart submitted a paper dealing with the application of existing methods of working in Alberta to the conditions obtaining in our bituminous mines. I must confess that the perusal of his paper did not enlighten me either as to what might be a method preferable to those in vogue or even to Mr. de Hart's ideas on the subject, nor did the ensuing discussion of Mr. de Hart's paper afford any great clarification of the problem. The outstanding idea, supplied by Mr. Dick, seemed to be that a retreating system could not be employed, as no operator would feel justified in risking the capital necessary to driving to the boundary when the whole might be jeopardized by a fire breaking out in the waste. That a fire would break out in the waste of any adit-level working seemed to be conceded by all, and with that I agree; that an ignited waste could not be safely sealed off by means of stoppings in a coal barrier-pillar appeared to be the contention of Mr. Dick, or perhaps he attributed this idea to the Mines Branch-anyhow, it seemed to loom over the discussion like a miasma. With this aspect I do not agree, as ? reliance is placed wholly on stoppings in the thick seams of South Staffordshire, even in fiery mines. In the thick coal at Exhall colliery, or elsewhere in Warwickshire (34 feet 4 inches) containing hard and soft coal in layers, a fire assuming serious proportions is sealed off. By the way, retreating long-wall methods are employed. In Fifeshire, sealing off fire in the Dysart mine has been accomplished successfully. The seam averages about 20 feet thick.

Jan 1, 1924

By Amir Karami, Derek Kinakin, Catherine Schmid

The Mathews Stability Graph Method (Mathews et al., 1981) has been used by geotechnical engineers and mining engineers for over 40 years to estimate the performance of longhole open stopes in underground mines. The method is widely used and accepted by practitioners because it is relatively simple to use and can be modified to account for observed performance at a given mining operation. While the simplicity of the method increases its accessibility and utilization, it does not intrinsically account for variability in the various inputs, including rockmass quality, structure, stress, or stope orientation. This paper presents a modified approach for the Stability Graph Method, whereby Python scripts are used to process available geotechnical datasets and combine them with actual or potential distributions of Q parameters, induced stress, structure, or stope orientation. The resulting Stability Numbers are then plotted as a contoured distribution on the Stability Graph.  This allows the practitioner to quickly incorporate large datasets into the analyses, while also developing an understanding of how variability in rockmass quality, induced stress, structure, or stope orientation could affect stope stability.  This paper presents the fundamental principles of the Stability Graph method, the Python script and workflow, and two case studies to demonstrate the utility of the tool.

Oct 1, 2024

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004

By G. Watson, S. Sawyer

A Method to Calculate Hydrodynamic Loads on Underground Bulkheads Bulkheads are structures built in openings in underground mines to impound water, preventing the water from entering the active mine workings. These structures not only have to be designed to withstand the static, hydraulic pressure, but also the dynamic or seismic pressure, which would be generated by an earthquake. Bulkheads can be considered underground dams. Unlike dams on the surface, bulkheads are often subjected to hydraulic heads that exceed the heights of the bulkheads. Theodor von Karman in 1933, and Westergaard earlier, developed the equation by which the hydrodynamic pressures on surface dams could be calculated. Civil engineering handbooks of today contain this equation. In this paper, using the methodology developed by von Karman and Westergaard, the authors have developed an equation by which the hydrodynamic forces on bulkheads could be calculated when the hydraulic head exceeds the height of the bulkhead.

Jan 1, 2007

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

A simple method of designing effective fill drainage systems for slurry backfill is presented. By using the proposed method, it is easy to calculate and predict the expected fill drainage rates or to provide additional drainage systems to accelerate the fill drainage. The fundamentals of hydraulic fill and an efficient method to determine its permeability is also explained. The safety in hydraulic filling and bulkhead stability depends totally on achieving effective drainage regime for the fill. This paper provides the basis for creating such efficient drainage regimes. The recent fatal fill bulkhead failures in Australia were the result of poor drainage from the respective fill masses, and therefore it is more important to provide suitable drainage arrangements to continue using hydraulic fill to the benefit of the mining industry. At present there is no procedure available to mine operators to estimate the expected bulkhead pressures to design a satisfactory bulkhead. Some mines are constructing bulkheads after their initial investigations carried out years ago. Other mines have simply borrowed the ideas from the pioneer mines and using in their areas. It is high time that we develop a rational approach to estimate the expected bulkhead pressures for the design of bulkheads. We need a simple model that could be understood and used by the mine operators on a day-to-day basis. This paper also presents a model to predict the bulkhead pressures for designing safe bulkheads.

Jan 1, 2002

By Kugan Kuganathan

Pastefill is being increasingly considered as a viable fill by underground mine operators. Mount Isa Mines (MIM) chose pastefill to fill their deep copper mine (>1200m deep) after considering various other types of fill in the feasibility studies. During the development of pastefill at Mount Isa (1996 - to date) the Mining research of MIM developed two cost effective, reliable and simple testing methods and used. With the help of these tests the behaviour of MIM pastefill was studied thoroughly and the most optimum mix design for pastefill was achieved. The MIM's pastefill plant, the largest in the world with a capacity of 450rph continuous pastefill production and unique in the process used, has been built (1998-1999) to produce pastefill to the specification developed through extensive testing program using the Flow Cone and Mini Slump cone Tests. As a consequence, it is now possible to select the optimum pastefill mix designs and predict their flow behaviour in bore holes or pipe lines using only these tests. MIM Blended Tailings Pastefill (BTPF) uses 3-3.55 Portland cement and the cost of pastefill is much lower than the total tailings pastefill, that could be produced from the same tailings.

Jan 1, 2001

By Axel Preusse

In the Ruhr district, pipelines of public and private infrastructure are made of cast iron, steel, plastics or asbestos cement. Legal framework, technical regulations and normative standards define which pipeline materials may be used for the transmission of which kind of product Thus ground water endangering substances as well as inflammable or explosive products are only permitted to be transported in steel-made pipelines. Ground movements, due to underground mining, are transmitted via the soil to the pipeline and cause extra strain within the steel pipeline (Figure I). In extreme cases durable deformations may occur, characterized by an oval profile or a fold in the pipeline. To avoid or minimize damages, balancing elements are installed into the concerning pipeline, reducing the ground movements which might otherwise cause damages. [ ] The distance between the balancing elements is not arranged by random, but by a calculation method developed in a doctoral thesis [Spielberg, 1999] which represents the actual available standards in science and technology. The calculation method considers all relevant influencing variables with impacts on the movement behaviour of steel pipelines in mining areas, such as technical data of pipeline design (e.g. steel grade, wall thickness, weld seam quality), soil conditions (e.g. friction), laying depths of the pipelines, the operational impacts (working pressure, corrosion) and the mining impacts. As of today, mining has caused no damages to steel pipelines protected by this calculation method.

Jan 1, 2004

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

NIOSH is conducting research to reduce the silica dust exposure of workers at surface coal mines. One goal of this research is to evaluate the relationship between drilling parameters, rock strata and silica dust generation. This study involved measuring blast hole emission dust from a rotary drill rig which required sampling high concentration dust (>400 mg/m3) for silica content in a high velocity airstream. To measure dust initially, traditional sampling methods using personal sampling instruments were attempted in and around the shroud area of the drill with no success. Variations in the dust cloud concentrations under the shroud, the condition of the shroud and its orientation over the hole, and ambient air conditions prevented consistent and accurate dust measurements from being obtained. Amore consistent dust cloud is necessary for accurate measurements. An area of the drill’s dust collector system that consistently draws the emitted airborne dust from the hole is the collector tube. This tube connects the drill collector’s vacuum and dust filtration system to the shroud area. Assuming the collector system is working as designed, sampling from the collector tube would enable more consistent and accurate samples to be taken. However, current personal samplers are unable to sample in the concentrations and velocities experienced in the collector tube, so another method had to be devised. To achieve the desired results, an in-stack cascade cyclone was used. Preliminary field testing shows positive results.

Jan 1, 2003

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By O. J. R. Baena, I. C. Sánchez, J. L. G. Guzmán

Frontino, a municipality in western Antioquia, Colombia, has more than 200 years of mining tradition. Currently, mining activities are carried out for lode gold using subway tunnels, where the grinding of the material is done in "cocos", whose energy depends on internal combustion engines and ACPM, environmentally polluting and inefficient methods. In accordance with the Sustainable Development Goals as an initiative developed by the UN, different mining methodologies that are aligned with these are constantly being analyzed. This study proposes to eliminate the use of hydrocarbons in artisanal mining, mainly promoting Sustainable Development Goals 7, 9, 11, 12, and 13. This will be achieved through an energy transition to renewable energy sources that take advantage of the topography and water resources of the area, providing advantages to the communities that live there, such as lighting, electricity for cooking, ventilation for mines, etc

Mar 2, 2022

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple entry section of the Bruceton Experimental Mine. Chambers filled with one hundred and eighty kilograms of Pittsburgh seam coal were ignited and allowed to burn until well developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires and the quantity required to extinguish the fires compared to the amount of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 22 L to extinguish the coal fires, while two commercially available additive-water solutions required an average of 30.6 and 30.3 L, respectively. The average amount of water required to extinguish the fires was 28 L. An analysis of covariance, using the thermal energy of the coalbed, Q, to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, while the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 1992

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

By Nikolaos Petropoulos, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature. In this study, pure emulsion was tested in confined conditions to better simulate the behavior of the detonation of the explosive in rock mass conditions. A methodology is proposed for carrying out the evaluation of the explosive performance. The blasthole diameter of the samples varied from Ø 25 mm (0.98 in) up to Ø 65 mm (2.55 in). The confiner was a magnetic mortar cylindrical sample with mechanical properties similar to a rock mass. A streak camera and VoD probes were used to measure detonation front curvature and VoD. The data was analyzed and correlated with the physical parameters of the explosive. Additional to this, the data was further used to calibrate numerical models in LS-Dyna.