Search Documents

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By Ren G. Dong, Kristine M. Krajnak, Dan Welcome

Continual occupational exposure to vibrating hand tools can damage the neural, vascular and other soft tissues of the fingers. Rat tail models have been developed to investigate the biological responses of the tissues to vibration.1-2 However, the biodynamic response of the tail relative to that of the human fingers has not been characterized. The objective of this pilot study was to compare the transmissibilities of rat tails measured via a scanning laser vibrometer to those of human fingers gripping a handle. Methods In Part I of this experiment, four male Sprague Dawley rats (6 weeks old) were exposed to discrete 5g-rms sinusoids of 32, 63, 125, 160, 250, and 500 Hz. The rats were restrained in Broome-style restrainers with their tails constrained without compression to an exposure platform via elastic straps as shown in Figure 1. The platform was attached to a vertically vibrating shaker. The vibration was measured for the array of points shown in Figure 1 using a scanning laser vibrometer (Polytec) and the transmissibility calculated for each point on the tail relative to the reference points on the platform. In Part II, three male human subjects were exposed at the frequencies specified in Part I - with the addition of 1000 Hz - at a magnitude at the ANSI <0.5-hr limit up to 63 Hz, after which the acceleration was held constant at 5g-rms. The subjects gripped an instrumented handle at 20 N as shown in Figure 2. The transmissibility was calculated relative to the reference points on the handle. [ ]

Jan 6, 2006

By P. S. Hettinger

Land Application Discharge (LAD) is a useful method of disposing of waste water from mining operations and in certain climatic regimes, stormwater runoff. LAD systems function under the premise that metals, salts and nutrients in water are dispersed over a large area and are effectively assimilated into the soil profile. Depending on the soil structure, migration or mobilization of dissolved metals through the soil profile can be Substantially reduced. Land application of treated effluent from sewage lagoons or waste water plants was probably the first general use of land applied water. LAD has gained popularity with the mining industry as a means of disposing of waste water and process water. In addition, large volumes of snow meltwater and stormwater are often placed in storage in Montana during spring, and Land Application Discharge has shown to be an effective method for disposing of stormwater during the dry, summer season. LAD can also provide an alternative to recycling or treating waste water at on-site waste water treatment plant&. Application of stormwater or process water can result in little or no change to the background concentrations of metals in baseline water quality samples. One cautionary note about LAD: high salt concentrations and pH values are associated with process water from heap-leach facilities and are known to cause burning of local vegetation. Some pre-treatment of process water may be necessary to prevent such environmental problems.

Jan 1, 1994

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By Trevor Harris, Martin Harris

"This paper evaluates the effect of grind size on the flotation performance of a platinum ore from the UG2 reef of the Bushveld Igneous Complex, in South Africa. The study was conducted on the Mintek Flotation Pilot Plant Facility, located in Johannesburg, and represented a thorough evaluation of the application of the flotation modelling methodology developed jointly by the University of Cape Town and the Julius Kruttschnitt Mineral Research Centre at the University of Queensland through the AMIRA P9 Project. A simulation model of the pilot plant data was successfully implemented, providing a set of circuit modelling parameters that appeared to be both consistent and well correlated to measurable characteristics of the ore and the pilot circuit operating conditions. The findings indicate that the methodology that was used could well provide a useful framework for developing optimisation criteria for industrial flotation circuits in combination with appropriate feed grind size and regrind size targets.INTRODUCTIONIt has long been recognised that the size distribution of an ore is one of the most important factors in the determination of the performance of a flotation process. It therefore follows that the optimisation of a flotation plant cannot be considered without due recognition of the interdependence of this process with the process of comminution. There are numerous qualitative guidelines for the selection of an optimum grind target for a particular operation. Mineralogical analysis can readily provide information on liberation as a function of grind, and the desirable particle size range for optimum mineral flotation is well established in both theory and practice (see for example Trahar, 198 1). For some operations, meeting these two criteria simultaneously is relatively simple. For the majority of operations, such mineralogically “easy” deposits, if they ever existed, have long been exhausted, and the optimum grind represents a highly complex compromise between liberation and overgrinding of both desirable minerals and gangue. This is particularly true for circuits that include regrind stages, where both primary and secondary (and sometime even tertiary) grind targets must be specified. As has been pointed out in a recent paper by Bazin and Hodouin (2001), there is little or no information in the literature to assist plant engineers in the selection of optimum grind targets for complex ore deposits, so current practice is primarily based on rules-of-thumb and experience. This problem is further compounded by the fact that once grind targets have been selected for a particular operation, the assessment and adjustment of these targets based on plant surveys is extremely difficult, time consuming and expensive, and is often not attempted unless the plant significantly underperforms relative to expectation. It is therefore clear that the development of a practical quantitative approach to this problem is a high priority for flotation research and development studies."

Jan 1, 2002

By J. A. Drozdiak

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

By J. A. Drozdiak, A. Bamber

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By L. E. Young

IT has been said the British Empire was built on British Coal. In all the postwar planning for Great Britain the necessity for producing cheap coal and the prosperity of the coal industry are given first consideration. On Jan. 23, 1945, there was released in London a "Report to the Colliery Owners" which had been awaited with great interest. This was entitled "A Plan for Coal" and was the recommendation of Robert Foot, chairman of The Mining Association (Colliery Owners), prepared at their request. Presentation of the "Plan" at this time is particularly significant as it is an answer to the demand for nationalization of the coal industry by the Labour Party and at the same time is a carefully considered program for postwar reconstruction, prosperity, and stability. In the words of Mr. Foot, If the coal industry for the first ten years after this war is to find itself in a situation similar to the one it occupied for the ten years following the last war, with its record of disputes, strikes, stoppages, short-time working, unemployment, and, with it all, a completely insufficient margin of profit, and all the insecurity and instability in our basic industry that was brought with them, it is goodbye to any real prospect of full employment, social security, and high standard of living. To present an elaborate review of the conditions which have brought to a crisis the unfortunate situation in the British coal industry is here unnecessary, but certain of the salient points

Jan 1, 1945

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 12, 1979

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1980

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By John C. Edwards, Robert C. Bates

Modeling uranium mine radiation control methods and natural environmental radon variations is an extremely complex endeavor. A number of authors have examined particular facets of the problem and have proposed models for their area of interest. Bureau of Mines personnel brought together many of these individual studies, and from them have attempted to develop a coordinated plan for modeling radon daughter concentrations in the uranium mine environment. This approach is described.

Jan 1, 1981

By W. H. Geis

THE following pages summarize the causes that led to the suggestion of unit operation of the Paloma field, the organization of committees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan.

Jan 1, 1942

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By Roy M. Fleming, Christine B. New

The federal standard for limiting exposures to miners from radon daughters was reduced from 12 working level months (WLM) per year to 4 WLM per year in 1971. However, even at that time some researchers were concerned that the new limit would eventually be shown to result in an excess risk for lung cancer mortality in miners. The National Institute for Occupational Safety and Health (NIOSH) is now engaged in a comprehensive review of this topic. As the lead agency in this project, NIOSH has developed a work plan and established a work group to implement this plan. The procedure and specific considerations are outlined in the work plan for developing a comprehensive ionizing radiation standard recommendation for all miners, underground and surface. Such a recommendation will not only include estimates of health risks at various levels of exposure, but also appropriate recommendations for medical monitoring, sampling and analytical methods, sampling strategies, posting, engineering controls, personal protective equipment and recordkeeping. The work group has twenty-four members. Eleven members are NIOSH personnel representing six divisions of the Institute. The remaining thirteen members represent other federal agencies, specifically the Bureau of Mines of the Department of the Interior, the Mine Safety and Health Administration and the Occupational Safety and Health Administration of the Department of Labor, the Office of Radiation Protection of the Environmental Protection Agency, and the Bureau of Radiological Health of the Food and Drug Administration, Department of Health and Human Services. Several factors contributed to the decision to initiate this project. First, the efficacy of the current standard was considered. An initial study group was formed in the spring of 1980 by NIOSH to identify and evaluate articles that contained information on lung cancer mortality risks at and below the present permissible exposure limit. The conclusion drawn from their evaluation was that a two-fold excess risk of lung cancer mortality at and below 120 cumulative working level months (CWLM) of exposure to radon daughters is evident. This composite indication from selected studies was of sufficient magnitude to justify further evaluation. The study group, however, recognized that other studies and information must also be considered in a quantitative risk assessment which would form the basis for recommending an acceptable and feasible permissible exposure limit. A second factor in the decision to pursue further evaluation was the gaps in the current standard that had previously been identified by the Mine Safety and Health Administration (MSHA). These included lack of medical monitoring of underground miners and absence of regulations for surface miners. The seriousness of the health hazard relative to other hazards in mining was also considered. Along with exposures to silica and asbestos fibers, radiation was judged to be one of the major health hazards in mining, These combined factors constituted the justification to develop criteria and recommendations for improved mandatory health standards. The development process begins with a survey and review of the available world-wide information on the topic, including data and information developed by NIOSH. The end product of this review is to be a document that will contain an evaluation of the collected information and support for any recommendations that are made. To develop this document, the present work group has been divided into five task groups with the following emphases: Health Effects, Medical Aspects, Monitoring, Environmental Exposures, and Engineering Controls and Work Practices. The Health Effects task group is to evaluate the evidence from epidemiologic and animal studies of adverse health effects associated with all forms of ionizing radiation encountered in mining and milling operations. The "weight-of-evidence" of the results of all relevant and useful studies will be summarized, with the reasons for emphasizing the cited studies. The critical cells or tissues and the factors that should be considered in estimating the dose to these areas from various types of radiation will be identified. An evaluation will be made of the possible impacts of smoking and exposure to diesel exhaust on the determination of health effects related to radiation. The implications of biologically redundant dose in terms of the time between tumor initiation and death will also be analyzed. The Medical Aspects task group is to review the generally-accepted and the state-of-the-art medical technology for the detection of adverse health effects from ionizing radiation exposure. An evaluation will be made of the accuracy of urine and fecal analysis, wholebody counting, chromosome analysis and nose blows, as well as their usefulness for early detection of adverse health effects. Early detection is of little utility to the affected individual unless subsequent medical care can improve the prognosis. Recommendations for screening tests will be made after carefully considering the accuracy of the diagnostic procedures and the usefulness of early detection. Required recordkeeping and transfer rights will also be addressed. The Monitoring task group is to consider the state-of-the-art technology for the monitoring of occupational radiation exposures. Instrumentation, sampling strategies and analytical procedures will be reviewed for both personal and area sampling. The implications of the associated levels of confidence for non-compliance decisions will be evaluated. The discussion will also include an evaluation of the feasibility of replacing present monitoring systems with recent technology and the impact that a possible lower permissible exposure limit would have on monitoring requirements. The Environmental Exposure task group is to investigate the field procedures and mathematical methodologies which have been used to quantitate exposure levels to the various kinds of ionizing radiation. The magnitude and direction of the possible biases in past exposure assessments will be estimated. Specific attention will be given to the controversies concerning the quantification of the biological dose equivalent and the feasibility of recommending standards for mixed radiation exposures which use "rem" as the unit of measurement. The Engineering Controls and Work Practices task group will analyze the advantages and limitations of

Jan 1, 1981

By Harry Holle, Gary Johnson

A plant trial was conducted at the Paddy's Flat plant of Dominion Mining Limited with the aim of comparing the ef evenness of oxygen and hydrogen peroxide as leaching oxidants. The Paddy's Flat plant is designed such that the leach train can be divided into two parallel streams, allowing the same or lurry to be eated in two identical trains. By effectively ehminatmg the influence of the ore variations on the results subtle differences in the performance of the two reagents hav been identified. . . The results of the plant trial indicate that the two reagents act m different ways, and that each may be more suitable than the other _for _the treatment of certain types of ore. In some cases a co bmation of the two reagents may be the most cost effective option. . or t e same chemical conditions in the leach pulp, including dissolved oxygen levels , the reagents achieve different gold leaching rates, and in some cases different ultimate leach extraction.

Jan 1, 1992

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995