Search Documents

By V 7. 0 / 300 dpi

LAST fall, having a number of ore samples from mine-development work carried on in spite of the "Revolution," I was forced to do my own assaying again, after a lapse of many years. This gave me an opportunity to build a furnace for crucible assaying, using wood for fuel, along lines which had been developing in my mind since the time 20 years ago, when as general factotum at a little mining camp in western Chihuahua, Mexico, I had converted a crucible charcoal furnace into one using the reverberatory principle. Wood-burning furnaces have been described in technical literature, but I believe the present application will prove helpful to those of the profession who are working in out-of-the-way places. The furnace is shown in detail in Figs. 1, 2 and 3. Remembering the trouble caused by stoking my first charcoal furnace too heavily, I fired this one with but a few sticks of wood at a time. By this method I could run out a charge of 12 crucibles in 30 to 35 min., using 50 sticks of ordinary stove wood. Later I fill up the firebox, holding about 40 sticks, get everything ready, put the crucibles into the melting chamber and "fire up." Just as soon as the fire is well started the draft door is closed and the furnace allowed to heat up slowly for 5 min. Then the draft is opened (the door to the ash-pit) and the fire allowed to roar, which it does. In 20 min. from the time the fire is lighted the fire door is opened, the fire stirred along the grates, and 5 or 6 more sticks of wood thrown in. In 25 min. from the start, the draft is closed again, the cover of the melting chamber pushed back and the charges poured. The melts will be found to be perfect, and the crucibles to pour absolutely clean, if everything has gone right, as will usually be the case. A new charge may be put in, and fired with S to 10 sticks of wood at a tine, and be ready to pour within 20 min.; but it is just as well to leave the crucibles in the melting chamber a full 2.5 min. By using 10 sticks of wood to start the fire and adding 5 sticks as often as needed, which will be as soon as the last sticks fed in are in perfect combustion, the smelting can be completed in from 30 to 35 min., using from 35 to 40 sticks of wood. I consider this to be the best method of stoking.

Jan 10, 1914

By William Hustrulid

Pre-split blasting is a primary technique for creating slopes with a minimum amount of unwanted damage to the remaining rock mass. Rock slopes created in such a way have both safety-related and economic advantages. The applications extend from road cuts to rock quarries to large open pit mines. For example, as deep open pit mines approach the end of their operating lives, slope steepening is one option to be considered. To be able to safely achieve and maintain steepened final slopes, good blast design techniques must be available and applied together with close operational control. Pre-split blasting is an important element in this slope creation process.

Jan 1, 2007

By G. Kang

The ferroalloys industry has generated historically substantial solid waste. The accumulated waste causes serious problems to the environment. However, it is possible to transform the solid waste into an environment-friendly resource to serve the human being. Consequently, the construction of plants that are ?environment-friendly? and that accommodate ?recycling? has become a target of most ferroalloy producers in the world to ensure sustainable development. This paper introduces the practice of Shanxi Jiaocheng Yiwang Ferroalloys Works, the biggest manganese metal producer in China, in the development of an ?environment-friendly and recycling? process. The process includes power generation using coal gangue, waste from local coal mines; hollow bricks manufacture using slag and fly ash from the power station; cement production using slag from ferroalloy smelting; recovery of ferrous and non-ferrous elements in the dust from the furnace gas cleaning system; application of silica dust in construction and so on. The final objective of the plant is to realize zero discharge of solid waste. The profit of the ?environment-friendly and recycling? process compensates in part for the operational expense of the environment facilities.

Jan 1, 2004

Discounted cash flow (DCF) methods are well suited and recommended as a primary valuation method for mineral assets for which there are at least indicated resources and some form of feasibility study containing engineering, production and capital and operating cost data. DCF methods are also applicable as a secondary or check valuation method for exploration properties for which no technical study has been prepared. For projects where little or no engineering, production and/or cost data is available, the process of formulating a project concept by specialists who do not possess experience and expertise in the relevant technical faculties is totally rejected as a basis for applying DCF techniques as a primary valuation method. Such an approach runs counter to The Australasian Institute of Mining and Metallurgy (AusIMM) requirement to apply relevant expertise to specific aspects of mineral valuation. Technical and commercial inputs to mineral valuation should be reviewed by specialists who have specific expertise in the relevant disciplines, and should be tempered by the quantity and quality of technical evaluation which has been undertaken and the development status of the asset.

Jan 1, 1994

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran

In this paper we develop a physics-based model for lining erosion in steel ladles. The model predicts the temperature evolution in the liquid slag, steel, refractory bricks, and outer steel shell of the ladle. The flow of slag and steel is due to forced convection induced by inert gas injection, vacuum treatment (extreme bubble expansion), natural convection, and waves caused by the gas stirring. The lining erosion takes place by dissolution of refractory elements into the steel or slag. The mass and heat transfer coefficients inside the ladle during gas stirring are modelled based on wall functions which take the distribution of wall shear velocities as a critical input. The wall shear velocities are obtained from computational fluid dynamics (CFD) simulations for a sample of scenarios, spanning out the operational space, and a model is developed using curve fitting. The model is capable of reproducing both thermal and erosion evolution well. Deviations between model predictions and industrial data are discussed. The model is fast and has been tested successfully in a ‘semi-online’ application. The model source code is available to the public at [https://github.com/SINTEF/refractorywear].

Apr 16, 2024

By R. J. Davidson

The chemistry related to the adsorption of gold, uranium, and transition-metal ions onto algal biomass (activated carbon) is related to the genesis of the Witwatersrand. Detrital gold being washed into the early basin, together with cyanide generated in the atmosphere, would have solubilized as the stable aurocyanide complex, the necessary oxygen being produced from the photosynthesis of carbon dioxide by primitive algae. Pebble-type conglomerates, while providing for the free movement of solutions containing the vital nutrients for prolific algal growth, would have screened of the sunlight, which would otherwise have degraded any free cyanide in solution. With the subsequent decomposition of the algal deposits, it is surmised that carbon-rich layers having adsorptive properties similar to those of activated carbon formed in the conglomerates. Under these conditions, gold (silver) in solution would have been adsorbed selectively as the cyanide complex, together with uranium as the carbonate complex. Any transition-metal ions present would also have been adsorbed onto such a substrate. The subsequent burial and compression of the gold-rich conglomerate with temperatures rising to about 400DC would then have reduced the adsorbed gold to the metal in a single segregated gold-silver metal phase (95 to 99 per cent of the contained gold), while leaving behind a sulphide phase rich in iron, base metals, and arsenic and containing some gold and silver. The recrystalization of this later phase may explain the presence of the rather consistent contents of secondary pyrite in the Witwatersrand conglomerates. Similarly, uranium minerals, some rich in titanium and carbon, may also have formed. An adsorption model would explain the very consistent trends in the gold-to-silver ratios of individual reefs in the Witwatersrand, which suggest an extensive hydrothermal system approaching isothermal equilibrium. Also, as gold grades increase, so silver grades generally decrease, indicating the sequential displacement of silver by gold as classically obtained with activated carbon.

Jan 1, 1990

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By Zibo An, Yong Hu, Hao Zhang, Hong Cao, Jun Xue, Zhen Luo

Phosphogypsum (PG) is a by-product of solid waste produced by the phosphate chemical industry. Owing to large emissions and massive storage issues, it causes a potential threat to our environment. Hereby, a method based on the precipitation and crystallization properties of calcium phosphate-magnesium ammonium phosphate (CP-MAP) followed by its adsorption on active solid waste powder is used as the main principle to treat PG harmlessly. The treatment process and its influencing factors for orthogonal experiments along with the associated environmental safety have been studied in detail. The results showed that this method could simultaneously remove soluble phosphorus and soluble fluorine from PG. When ACP, FA, HBM, and Ur were added to PG at a dosage of 3%, 13.5%, 0.04%, and 0.04%, respectively, the residual phosphate and fluoride contents was 0.061 mg/L and 0.856 mg/L respectively in the PG leaching solution. Compared to state-of-the-art approaches, this method exhibited higher efficiency in removing phosphate and fluoride. Most importantly, this method does not cause any secondary pollution in the process, thereby showing a novel application in large-scale industrial treatment.

Aug 29, 2022

By E. Rezaei

Glue is an animal protein that is used with other organic agent such as thiourea, in copper electrorefining. The concentration of glue has to be controlled carefully, because the electro-deposition process is often very sensitive to small fluctuation in the operating variable. This additive (glue) prevents rough and nodular copper cathode deposits. The nodular deposits may grow causing short circuits, which results in losses in production. Addition agents are effective in controlling metal growth; they modify the normal nucleation and lattice growth steps and refine the grain structure. In this research glue concentration was determined in an industrial copper electrolysis plant. A non-linear model with high capability was constructed and after optimizing its parameters, the accuracy and precision of the model were evaluated. For determination of glue concentration, electrochemical voltammograms in optimum condition (Differential pulse voltammetry technique, Hpulse=50 my, scan rate=10 mv/s) were plotted. Some information from voltammograms was transferred to the model as inputs and the calibrated model analyzed the information and the glue concentration was determined with high precision and accuracy. In this way there is no need to separate or add agents to remove interferences. This method has been successfully applied at Sarcheshmeh copper complex.

Jan 1, 2007

By Walter Weeks

THERE is very little useful material in the litera-ture on the construction of manometers, so each experimenter must devise his own instrument. I have experimented for a number of years and have finally built one that is satisfactory. If we are to obtain accurate friction factors in mine-ventilation problems we must use accurate instruments. The most simple and convenient instrument for the mea-surement of small pressures is the inclined manometer or U-tube. By changing the angle at which the tube is set, any desired magnification of the pressure reading may be obtained. The first question in regard to the manometer is: What liquid shall be used? Alcohol, in my opinion, is the best. It does not cling to the glass and it does not attack the rubber tubes. The next problem is the setting of the instrument at the proper angle. One method is illustrated in Fig. 1. The base plate AC is made horizontal by a level bubble. The plate AB, which carries the U-tube, is hinged at A. The angle z which AB makes with the horizontal may be made any value by pinning the end B at the calculated position on the arm CD. Such an instrument may be designed to read directly in inches of water if a liquid of constant specific gravity is used. If the specific gravity varies, a calculation is necessary to convert the reading into inches of water.

Jan 1, 1923

By Rick Wilkins

The stability of steep embankments is a major safety issue in open pit mining, highway passes, and earth filled dams. A failure in any one of these situations could mean a loss of very expensive equipment, a long term inconvenience, and more importantly, a loss of life. These possible catastrophes could be avoided by installing a reliable real time monitoring system. Robotic total stations (RTSs) give one possible cost effective solution to creating a near real time monitoring system. Repeated surveys at predetermined time intervals can automatically generate warnings if slope movements exceed a preset tolerance level. The variation in atmospheric refraction, combined with possible instabilities in reference targets, can make a monitoring system based on RTSs produce false alarms. A methodology has been developed at the Canadian Centre for Geodetic Engineering (CCGE) for reducing these systematic error effects. The methodology has been realized in the creation of a software package that has been successfully implemented at large earthen dams in California and at an open pit mine operation in British Columbia.

May 1, 2002

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015

By A. G. W. Knock

Logistic curves are used in the prediction of the primary production of tin metal from estimated worldwide resources. Such curves are asymptotic to the total cumulative reserves, which are a function of prevailing metal prices and total resources. The figures for tin resources are based on the findings of Robertson and of Brobst and Pratt, the latter authors including estimates of undiscovered deposits. It is suggested that tin production will slump from the present level to 100000 long tons per annum by the end of the century, but will reach a new peak of 200 000 long tons some thirty years later. It appears that production will never exceed 300000 long tons per annum unless substantial new resources, excluding those predicted, are discovered.

Jan 1, 1979

By B N. Noller, J C. Ng, S L. Bruce

Mining activities can result in the transfer of harmful elements, including arsenic and lead, into the environment. In Australia, one of the potential future uses of rehabilitated mine land is to stock grazing animals. Elemental uptake is dependent on bioavailable fraction for adsorption upon exposure. Bioavailability data are generally lacking in order to provide realistic health risk assessments relating to harmful elements from mine tailings in Australian conditions. Another key component of risk assessment is the ability to estimate a realistic exposure, or dose rate, of the tailings to the grazing cattle over a set period of time. Hence, we aimed to conduct grazing trials directly on rehabilitated tailings facilities in order to provide valuable in situ information on heavy metal dose rates and associated accumulation. For the laboratory-based evaluation of comparative bioavailability, groups of cattle were fed five days a week on a normal diet spiked with mine tailings or soluble pure salts of target elements (eg sodium arsenate, sodium arsenite and lead acetate) for about eight months. For the field validation, cattle were allowed to graze directly on rehabilitated tailings facilities over a similar length of time. Blood and a biopsy of the muscle and liver were periodically collected to monitor arsenic accumulation. At necropsy, blood, muscle, liver, kidney and other saleable tissues were measured for arsenic concentrations. Although this study was focused on arsenic, lead and other metals were also measured. Predictive models for arsenic and other metals have been established to calculate the maximum grazing duration without the risk of exceeding specific food safety guidelines. The outcome of this study is a predictive model for maximum beneficial use of certain rehabilitated tailings for cattle grazing where grazing activities do not impact on the integrity of the tailings dams.CITATION:Ng, J C, Noller, B N and Bruce, S L, 2014. A predictive model for beneficial use of rehabilitated mine tailings for grazing cattle after mine closure, in Proceedings Life-of-Mine 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R. L. Weigel

As Florida phosphate mining gradually moves from the Bone Valley formation to the Hawthorn formation, a greater portion of the minable deposit contains dolomitic diluents which result in lower product grades that can be detrimental to the production of phosphoric acid for fertilizer uses. One beneficiation technique found applicable to the phosphate pebble size range (3 X 16 mesh) is heavy media separation using suspensions of magnetite and ferrosilicon. As part of an ongoing investigation of dolomite removal technology, a pilot heavy media cyclone system was constructed by IMC and used in the testing of a variety of drill core composites and hulk samples. The results of these tests were used to develop a predictive model for heavy media cyclone separation based on pebble fraction assays and heavy media operating parameters. This model is currently being used in the evaluation of specific future mining areas.

Jan 1, 1984

By Chiharu Tokoro

Acid Mine Drainage (AMD), high acid water containing heavy metals discharged from mines, has been recognized as major cause of mine pollution. In Japan, the government spends billions of yen every year to prevent pollution caused by AMD in about 80 abandoned mines. It is widely recognized that the treatment could continue for long decades or an even century. However, costs and environmental loads are uncertain during the treatment because a predictive model for the quality of AMD, the dosage of neutralizer, and the amount of sludge that is applicable for abandoned mines with limited data has not yet been established. In this study, a two-steps predictive model for solution composition and neutralization chemical requirements of AMD in future was constructed based on the geochemical modeling. Requisite input data of the model was the past historical water quality data from AMD monitoring, such as metal concentration and pH in the solution, instead of the sample rocks as other conventional prediction methods. In the first step, solution composition of AMD in the future was extrapolated from the available historical data using geochemical simulation considering the first order kinetics for the mineral dissolution. In the second step, neutralizer dosage and sludge generation in the future was predicted based on the geochemical simulation supposing the chemical equilibrium and oxidation state for all of elements in the solution. Based on case studies of two abandoned mines in Japan, solution composition, neutralizer dosage and sludge generation were estimated. The results of this study demonstrate the effectiveness of our model for the prediction of AMD quality and chemical requirements of neutralization treatment after mine closing. The model is useful for the estimation of the neutralizer dosage and the sludge volume in abandoned mines with limited data. Keywords: acid mine drainage, predictive model, geochemical modeling, first order kinetics, water monitoring

Sep 1, 2012

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

By Qisu W

The ground vibration produced by the bench blasts of a single hole and a row of two or three holes is recorded in an iron mine. Using the seismic signal generated by a single-hole shot as the source function, we have developed a computer program of a simulating ground vibration by bench blast. The reasonable delay time of blast in the iron mine has been discussed tentatively with the Fourmap invented by Anderson, D.A. The seismograms measured from the single-row blasts of two or three holes have shown the method of simulating vibration is feasible on the whole. For large scale production blasts, a combination of the vibration simulation and the high-speed photograph is used to choose the delay Time.

Jan 1, 1990

By D. L. Marchioni

"The detection and quantification of the degree of weathering is an important aspect of coal exploration and mining. Tests for weathering which are suitable for the exploration camp should be fast, simple, and require minimal equipment and operator expertise. In this study, two tests which fulfill these requirements were evaluated using samples of Western Canadian coals. These tests, one based on the pH of a coal slurry and the other on the flotation of coal in a water/diesel oil mixture, do not appear to give consistent results and are not recommended as ideal weathering parameters.IntroductionThe weathering of coal results in a deterioration of those properties which render it suitable for use in industrial processes. Consequently, the detection and quantification of the degree of weathering is an important aspect of exploration and mining. Frequently, decisions related to the depth of the weathered zone must be made at the exploration camp and, therefore, tests for weathering which are fast, and require relatively inexpensive and portable equipment and minimal operator experience, would be very useful. The aim of the study reported here was to evaluate two tests used by U. S. Steel Corp. to detect coal weathering and which satisfy the requirements for use in an exploration camp. The study is a continuation of a more extensive examination of the detection of coal weathering by various methods, reported elsewhere (Marchioni, in press)."

Jan 1, 1981

By Patrick Mclaren, Peter B. Hale

Canada, with one of the largest continental shelf areas in the world, has done little to evaluate its offshore unconsolidated mineral resources which include heavy minerals (gold, chromite, rutile etc.) and industrial minerals (silica sand and aggregates). During glaciation much of the continental shelf was covered with an ice sheet and later subaerially exposed with the result that glacial, glaciomarine and fluvial processes deposited sediments that may contain heavy minerals derived from onland locations. With rising sea-levels, beach and nearshore processes may have served to concentrate heavy minerals by winnowing and removing the lighter mineral components. These potentially valuable resources can be found with suitable exploration techniques such as seismic profiling and bottom sampling. Gold deposits are known to exist off the coast of Nova Scotia, and on the basis of form er beach mining, gold deposits probably occur off Vancouver Island and the Queen Charlotte Islands. Large deposits of silica sand occur near the Madeleine Islands and it appears likely that supplies of marine aggregates are present close to urban markets or sites of future mega-projects such as oil field developments. This paper, which is based upon a review of literature and consultation with members of the Department of Energy, Mines and Resources' Coordinating Committee on Ocean Mining (DCOM), is the first step in assessing the Canadian offshore f or its resource potential with respect to quantified deposits, known and speculative mineral occurrences. Although this is a subjective evaluation, the potential appears promising. A more detailed resource inventory is required to provide a more certain assessment.

Jan 1, 1984