Search Documents

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because "the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

By Herbert Haas

1. INTRODUCTION COPPER matte is now converted into blister copper at a cost of only $5 per ton of copper, or, based on a 40 per cent. matte, $2 per ton of matte, which is the record of at least one large smelting Works; and it seems hardly likely that a further reduction, large enough to warrant, a change in existing practice, could be made in bessemerizing costs. But the new type of converter here described and the new practice proposed are intended, not so much for the treatment of mattes, as for the extension of, the process to the direct reduction in the copper-converter of pyrite ores

Jan 6, 1914

By O. Nyandoro, K. Khoza-Shangase, M. Madahana, N. Moroe

"Occupational noise-induced hearing loss (ONIHL) is classified as the leading work-related disability in the mining industry. ONIHL has a negative impact, on not only the health and occupational productivity of affected individuals, but arguably also on the country’s mining industry and economy. Hearing conservation programmes (HCPs) are an effective strategy in the management of ONIHL. However, current literature indicates that HCPs are not achieving the anticipated and desired outcomes in the South African mining sector despite the efforts focused on the management of ONIHL. Therefore, the purpose of this study is to propose the use of a feedback-based noise monitoring model as a tool for monitoring and managing ONIHL in the South Africa’s mining sector. This model is a basic static feedback model with practical applications such as estimating, monitoring. and providing quantitative information to aid miners, mining administrators, and policy-makers in decision-making around HCPs. Additionally, the model could form part of an early intervention and management strategy for ONIHL in the workplace. The strength of this model, although currently static, is that it encompasses all the pillars of HCPs and takes into account the policies concerned with the management of ONIHL in the mining sector. IntroductionHazardous noise levels (above 85 dBA) in the workplace place exposed employees at risk of developing a disabling occupational noise-induced hearing loss (ONIHL). ONIHL is the ‘partial or complete hearing loss in one or both ears as a result of one’s employment’ (Nandi and Dhatrak, 2008, p. 1). This type of hearing loss develops gradually as a result of being exposed to continuous or intermittent high levels of noise over a long period of time (McBride, 2004; Patel et al., 2010; Rappaport and Provencal, 2001). A hearing threshold below 40 dBs is classified as a disabling hearing loss (Yadav et al., 2015), resulting in a hidden condition that does not readily manifest itself (Tye-Murray, 2009, p. 3). Dugan (2003) describes disabling hearing loss as the ‘most prevalent, least recognized and least understood physical disability’, while Copley and Frederichs (2010) and Hermanus (2007) argue that permanent disabling hearing loss is a major contributor to the global burden of disease on individuals, families, communities, and countries."

Jul 1, 2019

Blast Engineers frequently use the terminology "the blast showed good heave", or even "the heave was better this time". It is reasonably obvious that "good" and "better" are not the best terms to use. It is also noted that any variation in the data can be misleading. The author proposes a more precisely defined and objective set of measures as tried and tested in a project in 1988. Simple objective measurements of a muck pile profile can measure 1. distance thrown 2. spread of material 3. heaping of material 4. skewness, or bias in the heaping 5. rotation of the mass This technique enables one to compare the profiles from different blasts without relying on subjective experience or judgement. Simple, artificial profiles will be presented to illustrate the problems of description; and then application of the measurement techniques to these profies will be discussed with physical interpretations. The mathematical techniques will be presented, and results of the application of the techniques to real data collected during research carried out at Baimsdale in Victoria, will be presented as illustration. The use of these techniques in mathematical modelling will be discussed.

Jan 1, 1990

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By Lon Santis, Michael Swisdak, David Leidel, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc (APT) have developed and released a quantitative risk management tool, IMESAFR (IME Safety Analysis For Risk), for the commercial explosives industry. Consequence algorithms in IMESAFR are considered state-of-the-art. Generally, they mirror those in SAFER (US Department of Defense Explosives Safety Board quantitative risk management software). The science behind the software has now been assessed for its maturity. Results have identified areas where additional test consequence data could improve predictions. To address these areas, full-scale testing programs to provide the needed data have been formulated. Proposed testing efforts include work to: (1) improve characterization of explosive articles now absent from SAFER, and (2) refine modeling of the Potential Explosion Site (PES) types, particularly small metal structures, also not found in SAFER. Goals of each program as well as requirements for conducting the tests have been established. Testing results are to be used to improve the algorithms and to further the state-of-the-art in risk-based explosives safety.

Jan 1, 2012

By Pierre Montrueil, Marcel St-Amant

Within the next few years, underground mobile equipment will be partially automated. Mining methods will integrate more and more automation. Such an evolution will be possible only if adequate underground communication systems are developed. This is expected due to the available competence in Canadian telecommunication, to the economic pressure on the Canadian mining industries for international competitiveness and to the social changes where a better working environment (i.e. less accidents) becomes a major concern. CCARM propose the concept of a Production Area Network for Automated Mobile Units called PANAMU as an intermediate size communication system. It can be implemented using mature present-day technology and it can be integrated in some mine wide communication systems. It can evolve so as to incorporate new technologies because of its modular concepts. In this paper, the communication requirements are estimated, the amtmptions are defined, the concepts of the PANAMU are presented and an over- view of its implementation is described. CCARM presents this article to the mining industry as a document for discussion.

Jan 1, 1994

By Paul A. Schafer

BALATOC mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.1 The region is a deeply dissected plateau, ranging in altitude from 3000 t0 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. 1): q6, 231 and 364, which strike about N.70°E. and dip 5o to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.45°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. NORTHEAST FAULTS The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on Pine fault and q6 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar No. I, and Sun

Jan 1, 1942

Flawed mining studies have been major contributors to poor investment decisions in mining for many years, contributing to the long period of poor industry profitability. Most of the major mining houses have now adopted quite formal processes and quality standards for mining studies to reduce the potential for poor investment decisions in the future. Other organisations such as the World Bank also have specific requirements for particular types of studies, such as bankable studies. This increasing requirement for rigour and discipline means a highly structured and phased sequence of studies is now required along with the development and adoption of industry-wide standards in mine ventilation studies. New terms in the study process such as ?independent peer review? and ?hold and review? are assisting in this process. More traditional terms such as ?feasibility study? and ?pre-feasibility study? now have much more precise technical definitions. Specific standards for the ventilation components of the various phases of a mining study are proposed in this paper.

Jan 1, 2009

It is widely accepted that the type of grinding media has an impact on the grinding chemistry and subsequent flotation behaviour of the sulphide minerals being separated. There are countless laboratory investigations demonstrating that inert grinding media produces more oxidizing pulp potentials, reduced levels of grinding media corrosion products, and superior concentrate grades and valuable metal recoveries. However, taking these results to industrial scale has proved difficult. This paper provides details of the protocol developed and used during a high-chrome grinding media plant trial. It describes the test regime employed to measure changes in pulp chemistry as well as concentrate grades and recoveries to produce a statistically meaningful result. The work also highlighted the need for close cooperation between the metallurgists on site and the researchers conducting the trial. To demonstrate the protocol, data gathered during a plant trail in a PGM concentrate will be presented describing the changes in pulp chemistry and metallurgical response observed.

Jan 1, 2012

By Allen Chung, John Twomey, Christopher J. Greet

"It is widely accepted that the type of grinding media has an impact on the grinding chemistry and subsequent flotation behaviour of the sulphide minerals being separated. There are countless laboratory investigations demonstrating that inert grinding media produces more oxidising pulp potentials, reduced levels of grinding media corrosion products and superior concentrate grades and valuable metal recoveries. However, taking these results to industrial scale has proven difficult.Work conducted at the Ernest Henry Mine, in north western Queensland, Australia, at laboratory and pilot plant scale clearly indicated that using a high chrome grinding media resulted in significant improvements in both copper and gold recoveries. However, advancing this work to plant trial represented considerable financial and technical risk to the mine.This paper provides details of the protocol developed and used during the high chrome grinding media plant trial. It describes the test regime employed to measure changes in pulp chemistry, and the statistical methodology utilised to interpret the results. The work also highlighted the need for close cooperation between the metallurgists on site and the researchers conducting the trial.To date, the trial has produced excellent results: indicating that the copper recovery has improved by about 2 percent. The successful application of high chrome grinding media to the Ernest Henry ore has increased metal value by $18.7 million USD per annum based on current spot price for copper.INTRODUCTIONTheoryThe application of electrochemically inert grinding media to mineral systems has been extensively studied (Table 1). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:"

Jan 1, 2011

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By Rob Farnfield, William Birch, Douglas A. Anderson

In the blasting industry, even to the most safety conscious shotfirer, misfires are a constant source of concern. In the United Kingdom, there are two types of misfire, as classified by the Health & Safety Executive. Type A occurs when testing a shot before firing reveals broken continuity that cannot be rectified. However, due to the fact that a majority of quarries use non-electric initiation [i.e. shock tube] that cannot be tested, this type of misfire is very unusual.

Jan 1, 2016

By Ryan CG, Cousens DR, Griffin WL

The proton microprobe is developing into a vital tool in the geosciences, through its high sensitivity for in-situ detection of trace elements in the ppm regime. This paper will describe the instrument at the CSIRO Heavy Ion Analytical Facility at North Ryde, including features crucial to its successful application in the geoscience. Examples of applications in the basic geoscience and mineral industry related research are described briefly. Conditions required for widescale applications in the minerals industry are Discussed.

Jan 1, 1989

By R. Hedin, M. Dunn

The Pennsylvania Department of Environmental Protection (US EPA 319 program) provided funding to aid a public-private effort in the installation of an environmentally-friendly system to treat abandoned mine drainage at Jennings Environmental Education Center (Pennsylvania Department of Conservation and Natural Resources). Through this cooperative effort among state and federal agencies, mining, excavation, and environmental companies, college and home school students, Girl Scouts, and volunteers, a successful multi-component passive system, readily accessible for upgrades and public education/research activities, was built. 90 people were directly involved in construction of this award-winning system and about 1000 people annually benefit from the educational opportunities.

Jan 1, 2002

By Charles F. Johnson

A pulse technique is described for the measurement of bar velocity. A low frequency sine wave pulse is used which allows the wave-length to become much larger than the lateral dimensions of the test specimen. The low frequency pulse method has been tested and compared with the resonant frequency method and the results show that both methods give, on the average, equivalent velocities.

Jan 1, 1971

By Anylmore M, Walker A, Fletcher A

Roasting of sulphide and sulph-arsenide gold ores produces unwanted emission of sulphur and arsenic oxides, and a less than complete recovery of gold. Pyrite loses sulphur and arsenopyrite loses arsenic at a useful rate at temperatures of 600¦C and above in an inert atmosphere. Sulphur and arsenic driven off can be condensed before entering the atmosphere. During the process, solid-solution gold redistributes itself on internal surfaces of the resulting iron sulphide. Two subsequent processing options may be used; direct cyanidation of the porous sulphide resulting from the anoxic pyrolysis, or a second-stage roast to oxidise the remaining iron sulphide. The first option may be viable under certain conditions of pyrolysis. The two-stage option has an environmental advantage over the traditional roast because it reduces oxide vapour emissions by 50 per cent. The second stage may provide nearly enough energy to sustain the entire process.

Jan 1, 1992

By David W. Pasho

The success of a collector vehicle, designed to recover manganese nodules under the conditions which exist in deep ocean mine sites will in part be determined by the effectiveness of pick-up and running gear mechanisms. For the purpose of qualitative comparison, some specific aspects of seafloor interactions with various concepts are reviewed utilizing existing data on seafloor characteristics and running gear/tool interaction with soils.

Jan 1, 1976

By Isiah M. Warner, Philip Oldham, John Kennedy, Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using a flame ionization detector The video fluorometry was the preferred method of analysis

Jan 1, 1983

By Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed. The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device. The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay. The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using an FID detector. The video fluorometry was the preferred method of, analysis.

Jan 1, 1983