Search Documents

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By Windsor C. R, Thompson A, Bywater S

A new high tensile strength, steel cable, that may be grouted into boreholes has been developed for use as rode reinforcement. The manufacturing technique produces a birdcage pattern in which the cross section varies along the length of the cable. The load transfer from cement grouts to birdcage cables has been demonstrated in laboratory tests to be better than that of standard 15.2 mm diameter seven wire cables. The manufacturing process also allows for a wide range of capacities which may be specified by design engineers. The various birdcage cable configurations have been applied as rock reinforcement in a number of Australian underground and surface mines.

Jan 1, 1990

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the Fundamental Sampling Error (FSE)–, Duplicate Sampling Analysis (DSA) and Segregation Free Analysis (SFA)–, are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody was calibrated using the DSA and SFA methods and the results compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to the power of 3. A later modification of Gy’s formula raises dN to the power (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of in the range 0.97 to 1.30. The average value for is shown to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry-preferred 1.5. It is suggested that for low-grade gold-bearing ores the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the FSE greatly simplifies the characterization of gold ores, now requiring only the calibration of K for a given mass and established fragment size. The implications of the simplified equation for the heterogeneity test are that, provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.

Jan 1, 2017

By Robert De Saro, Willis Bateman, Ramesh Jain

A Vertical Floatation Melter (VFM) has been developed (sponsored by DOE) which simultaneously decoats and melts organic laden scrap in a single unit. Scrap aluminum is fed into the top of the VFM where it falls through a cone. Hot gases flow upwards through the cone, imposing a variable drag force on the scrap. Equilibrium is reached in which the scrap weight equals the drag force and the scrap becomes suspended. The gases strip off and vaporize the organics. Next, the scrap reaches a liquid state, taking on a more aerodynamic teardrop shape, allowing it to fall into a holding furnace. Heat transfer coefficients are 10 times higher than that of a conventional furnace, allowing rapid melting at a low gas temperature. Typical energy use is well under 2,324 joules/g (1,000 Btu/lbm) with a metal yield from 92 to 98%. This paper reports on the operation and data of a 453 kg/hr (1,000 pph) pilot-scale VFM.

Jan 1, 2000

By R. K. Adams

The availability of digital computers costing less than $15, 000 makes them economically attractive as versatile research and experiment tools. Several such installations at Oak Ridge National Laboratory have shown that improvements in research productivity and experimental control accuracy can result from the proper application of a small digital computer. However, careful attention must be paid to several potentially expensive problems in 1) interfacing the experiment to the computer and 2) programming the computer. Two specific applications of very small computers to metallurgical testing and research are described. One is a system for data acquisition and precise temperature control associated with a thermocouple testing program, and the other is a system for pulse calorimetry determination of the specific heat of metals over wide temperature ranges and in the neighborhood of metallurgical transformations. The data acquisition system which uses a PDP-8/S computer monitors signals from up to 264 low-level thermocouple signals at two scanning speeds: 10 readings per second for long-term drift data, and 500 readings per second for transient data. The pulse calorimetry system which uses a PDP-8 computer accepts up to 6 signals of 0- to 10-v range and because of a larger analysis program, uses a bulk memory (magnetic disc) in addition to core memory.

Jan 1, 1969

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That sub- ject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public atten- tion has focussed as never before on the subject of commodity prices. To advocate stabilizing com- modity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent f.11 1k

Jan 1, 1978

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

The main factors controlling the electro- winning of zinc from impure aqueous sulphate electrolytes are reviewed. Zinc, hydrogen and impurities are deposited at the cathode. The current effic- iency for zinc is increased by increasing zinc/ acid ratio and current density and by decreas- ing temperature; and may be unchanged, increased or decreased by the presence of impurity ions. A qualitative comparison of observed and predicted impurity effects is in reasonable agreement. Quantitative treatment of the effects of impurities and cell additives is not available. A tentative explanation of the time dependence of current efficiency in the presence of some impurities is provided. The forms in which impurities are deposited is substantially unknown. Impurities may be classified according to the extent of cathodic deposition. Procedures for control of cathodic deposition of impurities are outlined. The main anodic reactions are the forma- tion of oxygen, manganese dioxide and sulphuric acid. Minor reactions include the oxidation of lead, silver, cobalt and chloride. The site of the anodic reactions and the reactions generat- ing manganese dioxide are uncertain and may change with time of operation. The anode behaves crudely as an oxygen electrode with

Jan 1, 1977

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The study proposes a dynamic path planning method for mining equipment based on spatial kinematics and real-time correction of coal-rock state identification. The method integrates real geological data and equipment operation information to improve the autonomous cutting of fully mechanized mining equipment.

May 1, 2023

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By John V. Beall

GOING west from Denver on Route 6, the direct road to Grand Junction, one gets the first glimpse of mining a few miles east of Denver near Idaho Springs where the workings of defunct gold mines are visible on the sides of mountains along the highway. One enterprising company is turning a profit by showing tourists through the mine and mill and then selling them gold samples on the way out. We have always known that mining people are ingenious, but this proves it. About five and a half hours fast driving west from Denver brings one to Rifle, Colo., which is the site of the oil shale mine, retorting plant, and refinery of the U. S. Bureau of Mines. As you drive up to the mine, you can see a portal high on the face of the cliff in front of you where the mine surface plant literally hangs by its toenails. Below, the retorting plant and refinery gleam in the sunlight. Up at the mine, Fred Wright will show you how the oil shale is extracted in two benches (a third bench would be used for commercial mining) by the room-and-pillar method. In mining the top level, an underground crew of thirteen men have been able to produce 1500 tons of shale in each eight-hour shift. To do this, the mine is thoroughly mechanized. The mining method is de- scribed in the September issue of Mining Engineering.

Jan 1, 1949

By John V. Beall

Since the U. S. Metals Refining Co. works was established, around the turn of the century, near the town which is now called Carteret, N. J., it has grown to be a major producer of refined copper and the main source of that special brand known as "oxygen-free high-conductivity copper." Owing to the complex metallurgical problems arising from handling a variety of raw materials such as copper concentrate from Matahambre, Cuba, copper and brass scrap from the New York area, and domestic blister copper, the organization is geared from top management down through its 2000 employes to maintain a high degree of flexibility in plant operation. The Company is a subsidiary of The American Metal Co. Charges for the smelter furnaces, one reverberatory furnace and one blast furnace, are made up in. bedding bins so that they may be tailored to the production of a constant grade of blister copper. The reverberatory furnace smelts the .sulphide charge, which may be a blend of ten different materials but principally the Cuban concentrate, and the matte from the process is poured into a converter. This reverberatory is 80 by 20 ft, silica lined with a slag bottom, fired by pulverized coal, and continuously side-charged from the top by bottom-dump cars which keep the side walls covered. It produces a 40 to 50 per cent copper matte. The fuel-charge ratio is 4.35 tons of solid charge per ton of coal. The furnace has a capacity of 10,000 tons of charge per month and produces from 5000 to 6000 tons of slag per month which must be disposed of. About 5000 tons of converter slag is produced monthly and returned molten to the reverberatory furnace. The converter gases go through a spray chamber to a Cottrell precipitator and thence to the flue system. Smoke from the

Jan 1, 1948

By Frank D. Adams

The Island of Ceylon, which is one of the most beautiful possessions of the British Empire, has been an abode of man from the very earliest times. The Veddhas, a wild tribe of some 4500 people still living in the fastnesses of the jungle in east central portion of the island, are believed to represent a remnant of the oldest inhabitants of which we have any actual knowledge, but in the caves in which they live there are found the stone axes and other implements of Palaeolithic people who represent the first race of men who inhabited our globe, and of whom they may be, for all that is known, the direct descendants. About the fifth century before Christ there came the Aryan invaders, apparently from the north of India, who drove the Veddhas into the remote fastnesses of the jungle and developed the remarkable Singhalese civilization whose high character is demonstrated by the remarkable and very extensive system of irrigation works which they built up, and through which they made the island wonderfully productive. Great cities arose, some of which are believed to have had a population of over a million souls and whose temples and public buildings show that the people were accomplished architects and sculptors.

Jan 1, 1926

By S. Uludag

Spontaneous combustion of coal has been studied by laboratory techniques using an apparatus in a small-scale laboratory testing. Coal?s inherent characteristics can be measured using Differential Thermal Analysis (DTA) and Crossing Point Temperature (CPT) methods. The DTA curve obtained after testing is compared with actual inherent moisture and its effect on spontaneous combustion has been investigated. It has been found that the Wits-Ehac Index increases as the inherent moisture of the sample increases. Therefore it can be deduced that liability to spontaneous combustion increases with increased inherent moisture. In addition, volatiles have a catalytic affect on self heating immediately after the inherent moisture is reduced. This is identified as stage two in the thermogram. The inherent moisture has a cooling effect during the initial stages of testing and is visible in the DTA thermogram. In addition, while an increase in carbon content means an increase in Wits-Ehac Index value, an ash content decreases the likelihood of on spontaneous combustion. Keywords: Spontaneous Combustion, Differential Thermal Analysis, Crossing Point Temperature, Moisture, Coal, Laboratory Testing.

Jan 1, 2007

By Luis Yacher

Proccesing plants currently have sophisticated regulation and control systems and there also systems of managment of the quality and laboratory variables, for the mine-plant transport managment, mineralogical extraction, characterization, maintenance managment were desgined to support specific operational business functions: to operate, maintain, control quality, manage the fleet, etc. The vision of systems dedicated to supporting specific business functions contradicts what is nowadays an integrated business operation, esenctially multidisciplinary and it which the managment and supervision process require access to heterogeneus information sources regarding their regarding their origin and managment system. The consecuence of ongoing pressure for operational excellence is the need of more "fine-lunning"of the processes must be adressed in a synchronized way. Hence, the need arises of restating the issue of operation and related information, for which a new conceptual and techonological focus is proposed aimed at the objetive of operational excellence.

Sep 19, 2006

By E. Rezazadeh Azar

Dump trucks are the main mean for hauling earth material within and outside of the construction and open-pit mining jobsites. The real-time monitoring of the material transportation trips is beneficial for proactive equipment management, volume estimation, and productivity measurement. The traditional manual observation is tedious, non-real-time, and expensive; therefore remote sensing technologies, namely GPS and RFID, have been employed for this reason. Ordinary construction videos are another costeffective alternative to monitor dirt loading and hauling operations in real-time. A vision-based system has been developed to recognize and count hauling trips. This system has three modules including object detection, tracking, and action recognition. This system processes videos taken from access roads in which it recognizes dump trucks and then tracks them throughout the viewfinder. The action recognition module is designed to reject false alarms and also terminate tracking. This way, the system is able to count the number of hauling trips and also record the time between each trip. Several state of the art computer vision algorithms were employed to develop this system. Some of these algorithms were modified using spatiotemporal information to minimize the inherent errors of the vision-based methods. The experimental results showed considerable performance of the system for practical application in the construction and mining sectors.

Aug 1, 2013

By Steven J. Schafrik, Michael Karmis, Zacharias Agioutantis

3-D or pseudo 3-D visualization of orebodies and mining related processes such as loading and tramming, are now commonly used by the mining industry. An approach is presented that can aid the engineer in creating the visualizations necessary for accurate presentations for use in public relations, safety training, production projections, reclamation plans, etc. It is shown that the creation of such digital representations of mining environments are independent of the mining package used to create the original mine design. Once a proper model has been created, any view of the areas is possible. These views can be taken from any number of stationary points or entered into an animation showing the progress of a mining construction. The paper focuses on the presentation of the steps used to accomplish the visualization and an example is for a quarry fill placement project.

Jan 1, 2002

By Jia-Shyan Shiau, Chung-Ken Ho

An uneven gas distribution through the burden layers inside a blast furnace (BF) results in abnormal gas resistance or pressure changes. Rapid variations in the abnormal gas resistance will lead to the occurrence of channeling. A visualization technology mainly made of pressure distribution was developed to predict BF channeling phenomena in this study. The real-time data of BF shaft pressure was used to create a 3D visual model by neural network algorithms and 3D real-time BF pressure changes were observed. The root mean square deviation (RMSD) of the BF shaft pressure was used as an index to set up the predicting criteria of channeling occurrence with the opening of BF Annular Gap Element (AGE), and a predicting system based on the criteria was built. The two criteria for the channeling alarm are the RMSD of the BF shaft pressure (> 0.15 kg/cm2 ) at the upper two levels, and the AGE opening being greater than 60%. This system has been installed in the China Steel Corporation (CSC) BFs, and the test results showed that a prediction can be obtained 8 to 16 min ahead of channeling allowing sufficient time for the operator to adjust the BF operation in order to avoid the occurrence of channeling.