Search Documents

By M. I. M. Darwish

In this paper, an effort was made to get more in-sight about the parameters that can affect air sparging technique optimization. Numerical simulations were used in predicting the effects of different parameters utilizing Shell?s in house MoRes simulator. The case of using air sparging to remediate source zone is considered in this work. Different air injection scenarios using continuous and pulsed air injection techniques, with different frequencies and durations, were compared. The amount of MTBE mass removed from the saturated zone and arrived to the ground surface, through the vadose zone, was the main criterion while comparing different air injection scenarios. The simulations results showed that pulsed air injection is better than continuous air injection in removing the MTBE and that the longer the OFF time is the better the MTBE removal.

Jan 1, 2008

By P. D. Morrell

Jetbelt is the trade name for the air supported belt conveyor. It does not use troughing rollers. Jetbelt conveyors support the conveyor belt on a thin film of air. The belt rides in a steel trough which has small holes equally spaced along the bottom of the trough. Air comes through the holes under the belt, thereby supporting the belt. The air pressure is provided by a single centrifugal blower that creates very low pressure, between 249 Pa and747 Pa [10" and 30" water column], depending upon the tonnage being conveyed. The volume of air required ranges between .001415 m3/S and .00283 m3/S [3 and 6 CFM] per lineal foot of conveyor. Therefore, depending on tonnage being conveyed, a 304.8m[1000'] conveyor might require as little as 1.415m3/S [3000 CFM] or as much as 2.83m3/S [6000 CFM.]. (See Figure 1) Horsepower requirements can be less than troughing idler conveyors and considerably less than some other forms of bulk conveying. Savings are most significant in horizontal and down hill (regenerative) conveyor designs. Horsepower to lift material, of course, does not change.

Jan 1, 1984

By Paul Grisley

Air-supported belt conveyors-conveying systems that replace troughing idlers with a film of air-were a revolutionary concept when introduced in the 1970s. But high installation and operating costs limited their application. Now, system refinements have led to successful applications, even under the challenging conditions of mines and process plants. In this presentation the author will discuss the latest developments in the engineering of these systems, including the ability to retrofit existing transfer points with modular air conveyor components. Air conveyor applications and limitations in mineral-handling operations will also be examined.

Jan 1, 2002

Air tabling of zircon-rich non-conductor products containing quartz enables most of the fine quartz present to be rejected without a markedloss of zircon. The coarser quartz in the air table feed can be separated from the zircon by screening one or more air table products, the oversize products containing most of the quartz and little of the zircon. Air tabling, with or without screening, is more efficient than wet tabling alone for the removal of fine quartz, but not for the removal of coarse quartz. Practically all of the quartz can be separated from the zircon by using wet tabling in conjunction with hydraulic classification, or by using air tabling in conjunction with dry launder treatment, in which a degree of sizing takes place that is advantageous for subsequent air tabling.INTRODUCTIONBack-dune and inland beach sand deposits usually contain fine wind-blown quartz, and neither spiral nor wet table concentration, alone or in conjunction, makes a clean separation of heavy minerals from quartz. Many rutile plants recover rutile and zircon from a low-quartz, wet-table concentrates by means of magnetic and electrostatic separation; some rutile and zircon are lost in the table tailings. Other rutile plants, and two of the ilmenite plants in Western Australia, recover rutile or ilmenite respectively, from a spiral concentrate containing several per cent of quartz, and then subject the non-conductor product to an additionalgravity concentration process to separate the zircon from the quartz. Some zircon is lost in the additional gravity process, but all of the rutile or ilmenite in the spiral concentrate is, or should be, recovered as high-grade concentrate. The higher recovery of rutile or ilmenite by this treatment method is offset by the expense of drying part of the feed twice, as a wet process is usually used to separate the quartz...

Jan 1, 1962

By Veliko Kertikov

Complicated processes of heat exchange and evaporation, leading to changes in the temperature and humidity of the ventilating air flow, take place during the driving of headings. In the case when virgin rock temperature is high, the increase in air temperature and humidity is significant. This causes a deterioration of climatic conditions in the headings. Procedures for predicting the changes in air temperature and humidity are discussed, together with appropriate calculations and computer programmes. Predicted results for example scenarios are used as a background for the selection of approaches and means to improve the climatic conditions in a dead-end heading using auxiliary ventilation.

Jan 1, 1997

By Gale F. Hoffnagle

INTRODUCTION On November 15, 1990, President Bush signed the Clean Air Act Amendments of 1990. These Amendments cover many aspects of air pollution control. The provisions which seek to control emissions of "air toxics" may, however, be the most far-reaching and will potentially have the greatest effect on American industry. The Administration has estimated that by the year 2005 industry will be spending $6.7 billion per year on air toxics control. Meanwhile, the Business Round Table has estimated that the price will be far higher, up to $62 billion per year, depending on how EPA and the States implement the program. BASIC REQUIREMENTS Any "major" source of emissions of 189 air toxics will be required to install "MACT." The translation of this statement requires some definitions: •MAJOR SOURCE - A facility (a contiguous property under single ownership and control) which has actual emissions of 10 tons or more per year of any single one of the air toxics or 25 tons per year of any combination of air toxics. •AIR TOXICS - Congress has provided a list of the 189 chemicals on this list. Those that may be important to the mining industry are shown on Table 1. This list can be changed by petition or by EPA. •MACT - Maximum Achievable Control Technology is to be defined by EPA for each industrial source category. EPA says there are about 400 categories. The Act defines MACT as: "the average emission limit achieved by the best performing 12% of the existing sources ... for categories with 30 sources or more" or, "the average emission limitation achieved by the best performing 5 sources in the category." TABLE 1 SELECTED AIR TOXICS FROM CLEAN AIR ACT LIST IMPORTANT TO MINING INDUSTRY Antimony Compounds Arsenic compounds (inorganic including arsenic)' Beryllium Compounds' Cadmium Compounds Chromium Compounds Colbalt Compounds Cyanide Compounds (dissociation compounds) Lead Compounds' Manganese Compounds Mercury Compounds' Fine Mineral Fibers Nickel Compounds Radionuclides (including radon)1 Selenium Compounds 1Previously listed under NESHAP 2The Administration may not list elemental lead as a hazardous air pollutant.

Jan 1, 1991

By Felix Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36' W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Teguci-galpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced.

Jan 1, 1940

By Felix B. Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36’ W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Tegucigalpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced. The nearest site for an airport was two miles north of the mine. The necessary grading was done by a small track-type tractor with a wheeled grader, which was brought in overland. Six weeks was required for bring-

Jan 1, 1940

By F. H. Wheeler

CONSIDERING the nature of this audience, I perhaps, in addressing you on the subject of air transportation as related to the mining industry, should speak with tongue in check or at least with some reservation. I know full well that many of you, veterans in the great mineral development in Canada, are perhaps more conversant with the overall aviation picture than I, for aviation to you has been the means to an end, and in many instances has been part and ?parcel in the success of your particular projects, in the form of the initial means of transport. I feel, however, that we in this room today have somewhat parallel geographic interests - yours in relation to what is in the ground, mine in the air - and also in the forests and in the streams - aviation, hunting, and fishing - things which have occupied my attention practically all my adult years. In the light of what has gone. before, and in view of present developments, I think you will agree with me when I say that I do not think there could be a more intriguing pursuit than playing a hand in rolling back Canada's tremendous northern frontiers, even if, at this stage, we have made but slight impression on the untold opportunities which lie in our wide-spread, undeveloped areas.

Jan 1, 1956

By H. S. Chiang, S. S. Peng

"SummaryAir velocity distribution surveys on four mechanized longwall faces are presented and discussed. Although there are discernible patterns in the velocity distribution, there are wide differences in distribution in the cases examined. This can be attributed to differences in mining and face geometry. An important factor is air leakage into the goaf.IntroductionOver the past two years several intensive air velocity surveys have been carried out in West Virginia coal mines as part of a programme aimed at understanding dust transport mechanisms on mechanized longwall faces. These are presented here and some of the patterns of velocity distribution are discussed.Ventilation survey methodologyThe air velocity vector consists of three mutually perpendicular subvectors; the vertical subvector is directed toward the roof, one of the horizontal subvectors is parallel to the coal face and the other pointing to the gob. The air velocity which was measured in this paper is the horizontal subvector parallel to the coal face.To record the velocity distributions at the longwall faces, the surveying stations and the surveying points were established as follows.(1) The first station usually was set at the third support from the headentry T-junction. Within the first few supports, the air coming from the intake airway encounters a sharp right-angle turn at the T-junction, and forms a turbulent region close to the coal face. The intake air in this region is also influenced by the motors that drive the face conveyer. But when the air reaches the different. But for the same face the number was the same. The main air-travelling area was divided into six to 12 equally sized sub-areas, and each surveying point was situated approximately at the centre of the sub-area.The velocity survey was carried out by two persons, one reading the meter and the other taking down the readings. A complete survey at one station took about 5-8 min. Usually, the dimension of the cross-sectional area was measured during that time.A third person used the smoke tubes to observe the following: (I) the air movement patterns at different locations; (2) the extent and the direction of the air leakage; and (3) the machines' influence on the main airflow. At the same time he observed and recorded the roof conditions and the compactness of the roof-caving in the gob."

Mar 1, 1989

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982

[ ]

Jan 1, 1938

By Austin Whillier

INTRODUCTION Use of air-cooling or refrigeration equipment in underground mines is needed when conventional ventila¬tion techniques do not maintain acceptable environ¬mental temperatures in working areas. Because refrig¬eration can be very expensive, it should be implemented only after all possible and practical steps have been taken to eliminate or reduce heat sources in the mine. As an example, to prevent the main ventilation fans from contributing heat to mine air, they should be located in the air return and not in the air intake. It is particularly important to prevent any direct contact between hot water and ventilation air, especially in mines which encounter large flows of hot fissure water. Any water hotter than the prevailing wet-bulb temperature of the ambient air must be removed by pipes located as close as possible to the water source. This hot water must not be allowed free contact with the incoming ventilation air at any time during the water's passage out of the mine. Although insulation of the pipes carrying the hot water is seldom necessary, direct contact between the air and the water must be prevented so the warm water cannot evaporate. REVIEW OF COOLING PRACTICES Spot Coolers vs. Centralized Refrigeration To eliminate a few specific hot places in an otherwise cool mine, it is possible to use devices known as "spot coolers." A typical spot cooler that uses chilled water is shown in Fig. 1. These devices consist of self-contained refrigeration units that are often mounted on rail cars for haulage to hot spots. The cooling capacities of such spot coolers usually are limited to about 100 kW or 30 "refrigeration tons." A refrigeration ton represents a cooling rate that produces 1.0 st of ice in 24 hr; that is a cooling rate of 3.517 kW (200 Btu per min). Typically, the electric-power consumption to drive the compressor motor of the refrigeration plant in mines is 1.0 kW per refrigeration ton, corresponding to a coefficient of per¬formance of about 3.5. The principal difference between spot coolers and centralized refrigeration plants is the method of re¬jecting heat from the refrigeration system. Centralized refrigeration plants always discharge heat into the reject or return airflow of the mine; often that is the primary influence in selecting the location for the underground refrigeration plant. Heat from spot coolers usually is rejected into drain water or into air that is not flowing to the location requiring the cooling. As a result, spot coolers remove heat from troublesome hot spots in the mine, injecting that heat-plus the electrical energy used by the cooling unit itself-into other working areas where the ambient conditions are cooler. In effect, this is "robbing Peter to pay Paul." In deep, extensive mines, spot coolers usually pro¬vide only temporary and, over the long term, expensive solutions to localized cooling problems. Centralized re¬frigeration plants are preferred for such mines, with cooling distributed throughout the mine as required. Fig. 2 illustrates a typical underground centralized re¬frigeration plant. Centralized plants lend themselves to improved maintenance at reduced costs while offering the economy of size. Refrigeration plants of larger unit sizes have considerably lower initial costs than smaller unit sizes. The remainder of this chapter is devoted to large refrigeration plants, with no further consideration of spot coolers. Cost of Refrigeration Total Cost: The total cost of refrigeration amounts to about $200/kW of cooling per year (1981 US $). This total cost breaks down into approximately three equal parts: 1) Financial charges, which include the interest and amortization on the capital cost of the initial installation, and the cost of necessary underground excavations. 2) Operating and maintenance costs which include the cost of the electric power to drive the refrigeration plant's compressors. 3) Distribution costs which include costs for pump¬ing, insulated piping, and air-to-water heat exchangers. The local cost of electric power, the number of operating months per year, and the method of refrigera¬tion distribution all contribute to the actual costs in¬curred in a given application. However, the variations usually are limited to no more than ±30% of the $200/ kW per year total cost figure. Cost Per Ton: Refrigeration cost per ton of mineral production can be calculated if the annual production tonnage from the refrigerated section of the mine is known. In most cases, this cost will be less than $1 .00/t. However, in deep mines with high rock temperatures, such as those found in South Africa, the total cost of refrigeration can increase to several dollars per ton of broken rock. Distribution In deep extensive mines, distributing refrigeration often accounts for about half the total cooling costs. As a result, careful consideration and planning must be

Jan 1, 1982

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By N. T. Moxon, D. Mead, S. B. Richardson

A laboratory and theoretical study of air decks was carried out to assess the effects of the size and location of air-decks on fragmentation. The degree of fragmentation was found to depend on both factors. As the size of the air-deck increases the degree of fragmentation is reduced relative to a full column charge. However, the reduction is relatively small until a critical size is exceeded. The critical size depends on the strength and structure of the surrounding material. A critical air-deck length of 30-35% of the original explosive column was determined for the model materials used in the study. A theoretical explanation of the results was derived based on pressure decay rate relationships. The location of the air-deck also influences fragmentation. The interaction and oscillation of the two shock fronts from the top and bottom charges mean that mid-column air-decks produce better fragmentation for the same air-deck length and explosive loading as top-column or bottom-column air-decks.

Jan 4, 1993

By P. Pal Roy, R. B. Singh

"This paper focuses on a number of interesting results to establish the theory and principle of air-deck blasting. It also gives the mechanism of breakage that takes place in air-deck blasting under varying charge load conditions. With these aspects in mind, the mine management can implement this up-coming technology to enhance safety and higher productivity. IntroductionThe method of air-decking has become an increasingly popular technique in production and presplit blasting. In the blasthole, an explosive column is combined with an airchamber. The main aim of the technique is to control breakage through effective distribution of explosive energy and thereby enhance uniform rock fragmentation. An air column lowers the initial pressure of the explosive products and simultaneously increases the time of interaction for the detonation front with the surrounding rock, which enhances rock breakage.To study air-deck blasting, CMRI initially conducted experiments using indigenously developed, low-cost wooden spacers of different sizes and strengths. Air-deck blasting was first tried using these spacers in 1993 at Jambad OCP, ECL and Chasnalla OCP, IISCO. The experiments were extended in 1994 at Bermo Mine, DVC. The results were subsequently published by Pal Roy et al., in 1995. It is worth mentioning that the performance of air-deck blasting during this period was only compared with conventional blasting practices without going into detail of the theory behind the process."

Jan 1, 2001

By F. Urekar, R. B. Pankhurst

"Air spaces and air gaps in an explosives column are known to allow greater distribution and cushioning of explosive energy from the rock mass. This energy distribution is enhanced if the explosives ' gases can be confined in the borehole for as long as possible by plugging and stemming above the air space.Power Plug is an inflatable plug which can seal a borehole at any point to separate the stemming from an air gap and explosive toe load.IntroductionThis paper will discussion-going work by C-I -L Inc. and operators of two open pit mines to study the results of using Power Plugs:I. Pit wall stability - the authors have found the Power Plug effective for wall control blasting in open pit mines.2. Selective mining of coal seams - the authors work shows the Power Plug allows mining selective coal seams by predrilling underseam waste wedges.Pit Wall StabilityWall stability in an open pit mine is essential for safety. Good wall stability can be achieved with wall control blasting techniques which cushion the effect s of the explosives charge by decoupling the charges from the borehole wall. The usual method of decoupling a charge in a large-diameter rotary borehole is to load the explosives in tubes (Fig .I) . We now believe the air deck system is effective in sea ling a borehole above the explosive charge to create an air deck within the borehole which will cushion the blast.In a linear decoupled charge, an air annulus surrounds the explosives charge and cushions the effects of detonation genera ted gases on the pit wall. In an air deck, i.e. with the hole plugged at the collar, the gases genera ted by an explosive toe load are sealed in the empty borehole column. After a period of time, these trapped gases produce radial cracking between holes along the entire length of the borehole.It is common practice to employ de coupled explosive charge columns in the borehole to limit blast damage to surrounding rock. The exact mechanism of energy transfer in such blasts, however, is not well understood. Interruption of the continuous explosive column in a borehole by means of stemming, or air decks, may also be viewed as another form of decoupled blast. Decoupling of the explosive charge from the borehole wall affects both explosive energy release and explosion pressure developed in the borehole."

Jan 1, 1988

By C. R. Woodcock, J. S. Mason

In almost any situation where particulate or granular bulk solids have to be conveyed, whether for a distance of a few metres or for many hundreds of metres, a pneumatic conveying system may be considered. Conveying by pipeline is convenient and clean, but running costs may be substantial because of the heavy air consumption and the trend has therefore been towards dense-phase transport in which the ratio of conveyed solids to conveying air is kept high. This paper concentrates on air-float conveying, which can be regarded as an extreme form of dense-phase conveying where the bulk solid is fluidised in a channel and then caused to flow, either by inclining the channel or creating a pressure gradient along 'it. Various designs of air-float conveyor for upward, horizontal and down- ward transport of powders are discussed, with special emphasis on the latter case. In situations where a continuous downward slope can be provided, the combination of air-fluidisation and gravity flow results in a conveying system that, for many kinds of bulk particulate solid, would be hard to better in terms of convenience, reliability and economy. The paper is concluded with a discussion of design features and performance of practical air-gravity conveyors, involving the handling of various bulk particulate solids, both in research and in full-scale industria1 applications.

Jan 1, 1980

By S. F. Shaw

The Seminole field was first drilled in 1913. During the next 10 years other attempts were made to discover oil in this field, but without encouragement until March, 1926, when the Indian Territory Illuminating Oil Co. completed NO. 1 Dyer in the Hunton lime for 1100 bbl. On July 16, 1926, the Independent-Garland interests discovered oil in the Wilcox formation when No. 1 T. Fixico came in at 4055 ft. and on Sept. 9, 1926, production reached a peak of 8040 bbl. On Aug. 1, 1927, the daily production of the pools making up the Seminole district amounted to slightly over 500,000 bbl., practically all of which was coming from the Wilcox formation. The Hunton formation has not been very productive of oil, but has maintained a fairly high gas pressure; this formation has been encountered at from 3800 to 4200 ft., below which there is about 100 ft. of Sylvan shale. The shale is underlain by 75 ft. of Viola limestone in a few places in which formation oil has been encountered. Below the Viola lies the upper Simpson formation in which is found the Wilcox sand. The depth of the Wilcox in the Seminole field varies from 3900 to 4500 ft., and initial production has reached as much as 12,000 bbl. The gravity of the oil is about 41° Be. The general practice is to set 6 5/8 -in. casing above the Wilcox and drill in, though in several cases 5 3/16-in. casing has been set for the oil string, and in a few instances, casing as small as 4 3/4 in. has been employed. Production Statistics Production for the Seminole district for the various months since its discovery is shown in Table 1.

Jan 1, 1928