Search Documents

By Baokuan Li, Fang Wang

"Comparing with the single electrode in electroslag remelting processes, two series-connected electrodes have the advantage of little inductance, lower power consumption and higher melting rate, which was widely used to produce superalloys and specialty steels. Detailed understanding of the electromagnetic field distribution is essential for both improving ingot quality and saving electric energy. In the present work, a 3D finite element model was developed for the magnetic field, electromagnetic force, current density and Joule heating field of electro slag remelting processes (electrode, slag and ingot) with two series-connected electrodes using Maxwell equation, Lorentz law and Joule law. The results show that the maximum current distribute occur at the middle of electrode, due to the interaction of selfinduced and mutual-induced of two series-connected electrode; associated magnetic flux density on the inner side of electrode increase and the outer decrease; The maximum joule heating is at the interface of slag and electrode. The parameter study shows that if the current frequency is greater than 35Hz, the current density in inner electrode tend to linear distribution; with the increasing of original current, The maximum current density near the wall in electrode will increase linearly; with the increasing of electrode innnersion depth and decrease of slag cap thickness and the maximum of the joule heat in slag will increase.IntroductionElectroslag remelting processes(ESR) are widely used to produce superalloys and specialty steels [l-3l_Two pair, four pair or six pair electrodes in electroslag remelting processes is common in casting large scale ingot, which has the advantage of little inductance, lower power consumption and higher melting rate, comparing to singe electrode. They have the same essence with two electrodes in ESR.Compared to the single electrode ofESR, the other electrode is added which can decrease the reactive resistance and power consumption in the two electrodes of ESR. It is a complicated metallurgy process with a series physical and chemistry phenomenon from the molten of steel to the solidification of ingot [4-71_ These physical and chemistry phenomenon originated the effect of alternating current of high intensity. The rule of the alternating current of high intensity which revealed the law of physical and chemistry phenomenon in ESR is the precondition of improving ingot quality and saving electric energy. Jihe Wei and Yongli Ren[S-9lstudied the distribution of electromagnetic field in single electrode ofESR with Maxwell equation and relative electromagnetic theory. It had the limitation that take the electrode and mold as infinite conductivity. A detail analysis of Electromagnetic fields in ESR had been conducted by Patel A D [JO-llJ using general stream-function formulation. It is difficult to extend to three dimensions which could not be used widely. Daniel V [lZJ and Kharicha A [BJ only analysis the current density associated magnetic flux density field and temperature field without the whole irlformation of electromagnetic field. Maopeng Geng [l4J considered the current density and temperature field of the real and fake electrodes in ESR without skin effect. As to the complication of the two electrodes of ESR, it is rarely reported the electromagnetic field and Joule heating field of the two electrodes in ESR. The rule of effect of electromagnetic and modification of numerical simulation should be studied in depth."

Jan 1, 2011

By D. C. Mahon, P. G. Sagert, M. R. Legeyt

INTRODUCTION Public opinion, over the effect of industrial development on the environment, has required government to institute guidelines for the protection of the environment both during the development of and after the decommissioning of mines. In no other area of mining has this requirement been more consistently applied in recent times than in the development of uranium mines. Uranium mines have been a focal point because of the very real uncertainties associated with the detrimental effects of radionuclides and the possible hazards of radiation. In order to determine if there is an environmental effect caused by a development or the storage of the mine waste as tailings, it is necessary to know what the quality of the environment was prior to the production of the tailings. This is the reason for baseline data programs. It is neither technically nor economically feasible to completely define the environment in any given region. Therefore, judgement decisions must be made prior to the development as to what aspects of the environment are more likely to be affected by the presence of the tailings, and to what degree. These decisions have evolved over a period of time based on information generated from existing facilities, scientific research, and the development of strong public opinions. This process is not static, but evolves with the growth of information and the technological developments which permit greater control of industrial pollution and waste management. A well-designed baseline program will reflect changes in science, technology and public attitude, even in advance of government regulations to enforce policy changes. RATIONALE FOR PREOPERATIONAL BASELINE STUDIES There are three distinct phases to be considered in the construction of an environmental assessment for a uranium mine tailings containment facility. I. Pre-operational 2. Operational 3. Post-operational (decommissioning and long term).

Jan 1, 1980

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multielement ground support system, there is a need to know the support characteristics that the shotcrete contributes to the overall system. To quantify the support provided by the shotcrete, flexural strength tests were conducted with two common, commercially available fiber-reinforced shotcrete (FRS) mixes using the round determinant panel (RDP) test method, ASTM C 1550. A portable RDP test machine developed by NIOSH researchers was used to determine the peak flexural load and residual load capacity for a steel FRS and a synthetic poly FRS that were sprayed using dry mix procedures and equipment. Besides the flexural strength and loading behavior determined from these tests, a method was also developed for measuring the width of cracks exposed on the underside of a shotcrete panel during a RDP test and relating these measurements to residual load values. Quantifying the peak flexural load and residual loads of a shotcrete mix through on site testing at a mine and visually assessing the loading cycle and load-carrying capability of the shotcrete applied to underground workings will improve mine safety by providing a better assessment of the stability of shotcrete supported entries.

Jan 1, 2010

By David E. Van Dillen

INTRODUCTION Current design practices for deep tunnels make extensive use of plasticity solutions by Newmark (1970) and Hendron and Aiyer (1971). These solutions are applicable to a circular tunnel subjected to a hydrostatic stress state in a Mohr-Coulomb plastic medium. The role of rockbolts is introduced into these solutions as a uniform internal pressure equivalent to the yield stress of the rockbolt pattern. The application of these solutions is hampered by their inability to consider the biaxial nature of the in-situ stress field or any surcharged stress, such as due to blast loading. As a means of considering the biaxial stress field, designers have turned to relatively costly alternatives, such as the finite element method. The recent work of Detournay (1983) simultaneously provided two generalizations to the state of the art of the analysis of circular tunnels. Whereas the solution of Newmark applies to nondilatant Mohr-Coulomb materials, and that of Hendron and Aiyer applies to materials having associated flow rules, the solution of Detournay covers materials of arbitrary dilatancy. Secondly, Detournay's solution is valid for biaxial stress states, as long as the problem remains statically determinate (St. John, Detournay, and Fairhurst, 1984). The topic of this paper is an investigation of various alternatives for introducing the effects of rockbolts into simple tunnel design charts developed using Detournay's solution. The study was conducted using the BMINES finite element code, into which rockbolt elements have been added (St. John and Van Dillen, 1983). These rockbolt elements allow for plastic deformation of the bolt, bolt

Jan 1, 1984

By Slechta JJ

The performance of a hydrocyclone treating fine coal has been examined over a wide range of feed and operating conditions.The results were expressed in terms of partition curves from which the water split to the oversize flowstream,the corrected separation size and reduced partition curves were determined-.The following conclusions were obtained. (a) The water split to the oversize flowstream was found to be dependent upon the vortex finder and spigot diameters of the cyclone and the flowrate and solids content of the feed slurry. (b) The corrected separation size was dependent on the solids content of the feed,and the vortex finder and spigot diameters.The hydraulic pressure (or flowrate) of the feed slurry did not have a significant effect.This phenomenon could be explained in terms of crowding of the particles at the Spigot.

Jan 1, 1984

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

By Zhu Tonghao

A method of calculating anti-slide pile, sheet pile, underground diaphragm and structure with anchors etc. is proposeed in the paper. The effect of the various layers of soil, anchors and bracings etc. on laterally loaded structures may be considered in the model. In the analysis the structure is divided into a series of elements. The transfer matrices of both deformation and internal force are established for each element. According to continuous condition neighbouring element should be connected. Thus the deformation and internal force of each element can be found out in conbination with boundary conditions. The method has a wider adaptability and it can be applicable to a great variety of the analysis of interaction between various structure and soil. If parameters in model are selected properly, the computed results would be in good agreement with the measured data.

Jan 1, 1991

By J. T. Crawford

The purpose of this paper is two fold. It will: (1) examine leasing analysis as a project evaluation criterion, and (2) compare the cost of leasing with other methods of financing. The use of leasing has grown extensively in recent years as a method of obtaining equipment. The computer industry has been highly dependent upon leasing from its earliest days to dispurse its equipment to the customer, while airlines and railroads acquire large segments of their aircraft and rolling stock by leasing. Over the last few years the mining industry has leased haulage trucks, bulldozers and other equipment of similar nature.

Jan 1, 1974

By Greg Hendon

Various methods have been used to evaluate the effectiveness of shields in place. The most common method used is static recording of leg pressures by visually examining pressure gauges. In an effort to more closely examine the shield cycle and therefore the shield effectiveness, Jim Walter Resources has implemented a program of monitoring utilizing a polycorder system which is capable of recording convergence and pressure measurements on a continuous basis. This paper will discuss two longwall panels at Jim Walter Resources which have been monitored.

Jan 1, 1990

By Ronaldo Luna, Donald Deardorff

"The use of load and resistance factor design (LRFD) is well documented since the 1960s for structural applications when it was first adopted into the American Concrete Institute Building Code in 1963 and was established for geotechnical applications by the Danish Geotechnical Institute about the same time under the name of Limit State Design (LSD).The Federal Highway Administration required all federally funded projects to use the LRFD method by 2007. Due to this funding requirement, recent LRFD research for geotechnical applications has focused on common bridge foundations (i.e., driven or drilled shafts), resulting in good documentation for design using these methods. Unfortunately, the practicing geotechnical engineer does not intuitively know how to create resistance factors for deep foundations systems that have design methodologies and installation techniques significantly different from driven or drilled shaft foundation systems.Helical anchors typically use semiempirical methods for preliminary capacity design and a torque correlation methodology during installation to verify required capacity. Here we provide basic information on the LRFD methodology for helical anchor design. Additionally, the First- Order Second Moment (FOSM) method is applied to a previous helical anchor study (Hoyt and Clemence 1989) to determine resistance factors for an ultimate tension capacity strength limit state.MethodologyThe concept of the LRFD method is to establish factors for both the load and resistance that account for uncertainties using probability theory. The factors increase the nominal load and/or decrease the nominal resistance such that the probability of failure is an acceptable value. LRFD also accounts for the effects of load combinations (dead, live, seismic, wind, etc.) by determining the probability of the combined occurrence. The general form of the LRFD equation used by American Association of State Highway and Transportation Officials (AASHTO) is:"

Jan 1, 2009

By A. Sadik

The proliferations of media sources and non-profits organizations in Ghana have put the negative impacts of mining on the ?spot?; this has resulted in public outcry about mining. Although, the gold mining industry has responded by implementing several voluntary measures to ensure sustainable mineral development, these critics label such measures as ?green wash?. In this study, a content analysis of newspaper articles of the Ghana Web Database was carried out after the collection of a total of approximately 900 newspaper articles from it. The data were statistically analyzed to chronologically examine the main media view points and the changing perception of mining issues as reported by private and public media. The results showed government, mining industry (Gold), illegal miners and non-profit & community groups as the main media view points and total of twenty-eight related gold mining sustainability issues. The findings of this study could be used by the gold mining companies to improve upon the communications of their unknown sustainable mineral development measures and to design effective communications and education programs for the public.

Jan 1, 2009

By Bernard York

Mine opening stability was investigated by loading model openings to failure. Eight-inch plaster blocks were cast with small uniform section openings passing through the centers. After curing, the models were jacketed and loaded hydrostatically in a closed vessel. Opening size, shape, and orientation were varied to determine how these factors influence opening stability.

Jan 7, 1953

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By D. G. Krige

By use of models based on the South African gold-mining industry, analyses are made of the effects of changes in the mining tax structure on the .State's tax income from potential new mines; also on the percentage of such mines likely. to be proceeded with. The percentage is affected by the correlation between changes in taxation and in the flotation pay limits !or new mines. It is shown that the State stands to gain both directly and indirectly from raising the level of the capital allowance and from its extension to all mines; and that the reduced taxation resulting from a lowering of the discriminatory high tax formula for the gold mines, would, in respect of potential new mines, be compensated for by a significant increase in the percentage of such mines that would be proceeded with.

Jan 1, 1979

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By Richard J. Robbins

This paper is presented with particular reference to the findings of the OECD Advisory Conference on tunneling held last July in Washington D. C. A great deal has been said about the Conference in the past few months, but it may be appropriate to review briefly the background and objectives of the Conference to better understand how the mining community can relate its underground excavation problems to the results of the Conference. OBJECTIVES OF THE OECD CONFERENCE The world demand for tunneling (the term tunneling is used here loosely to include almost all forms of underground excavation) is expected to grow at an in- creasing rate. During the decade of the ?70's, the demand is expected to at least double by comparison with the previous decade. Much of this increase in demand will be due to the rapid growth of urbanization around the world. As urban populations grow larger and denser, the conservation of surface land and the quality of the environment become more important. This aspect of the increasing demand poses a difficult challenge to those who must plan and implement urban development.

Jan 1, 1970