Search Documents

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By W Russell

The Hercudet Non-Electric Delay Blasting Cap System provides a means of achieving greater flexibility in the use of delays, using totally enclosed gas detonation circuits which eliminate the concussive effects of detonating cord trunklines in the confinement of access tunnels beneath pillars of ore. This is an account of one such pillar blast.

Jan 1, 1985

By J. S. De Lury

The metalliferous areas of Manitoba have been described in more or less detail. Since the descriptions were written some new prospects have come to light and considerable mining development has taken place in two or three localities. No attempt will be made in this paper to give an account of recent activities or to describe the several areas in detail. In a general way, geological conditions are similar in all metalliferous areas of the province, a similarity that invites a discussion of the prospects as a whole, the features that are common to all deposits and the reasons for their uniformity. Modern theories of metallogenesis have a direct bearing on such a discussion and an effort will be made to show their application.

Jan 1, 1925

By M. Yavuz

Decision Making (DM) can be defined as a selection process of the best one among the alternatives sets in order to obtain goal, and mostly has an uncertain situation [7]. Every mining engineer is subjected to a number of mining DM problems in daily mining operations. In reality, all stages of mining have its own DM problems. Most of time, engineers do not use scientific methods for DM problems. These problems can mostly be solved by the engineers according to their past experiences and practical studies. Mining engineers often use their intuition in DM process. Experience and intuition have been central to DM because of the frequent lack of quantitative data including geology, grade distribution and ground condition, as well as environmental, social and economic factors [8]. In decision process, linguistic variables become in question and decision makers may not know how these variables are computed [9]. So, the DM process may be qualitative, quantitative or combination of the two. The problem structuring and analysis process is conceptualized in Figure 1 [8]. The qualitative analysis is based primarily on the judgment, knowledge and experience of an expert (or team of experts). In a quantitative analysis, the focus is on facts and the data associated with a problem and a mathematical formulation that encompasses the objectives, variables and constraints of the particular problem. The quantitative analysis has traditionally been the subject of operation research and management science [8].

Jan 1, 2008

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

Conventional hand drawn isopach maps of the cover of the Bulli Seam are too eomplex for use in the delineation of large domains of similar cover. Isopach maps prepared from trend surfaces fitted to the cover data are much simpler in form and so provide a convenient method of delineating broad domains of similar cover.

Jan 1, 1968

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989

By Venkata S. Vutukuri

Assuming a number of discrete leakage paths and treating the airflow through leaky duct line as a series-parallel combination of airflows along the duct and through leakage paths, exact solutions for auxiliary ventilation problems can be obtained. A computer program "SEGMENT'' has been written to solve problems using this method. However, most of the investigators have treated the duct lines with a uniformly distributed leakage and many have derived formulas assuming various boundary conditions and levels of simplification for the design of a simple auxiliary ventilation system An appraisal of accuracy of the various formulas has been conducted using the results from the program "SEGMENT' as benchmark and the formulas which give accurate results have been identified. The ranges of application for all the formulas have also been determined for 5 %error.

Jan 1, 1993

The Bureau of Mines, through its Minerals Availability Program (MAP), investigates the mineral supply potential of the United States and market economy countries (MEC's) for a number of minerals considered essential to the U.S. industrial base. Major activities include identification of important mines and mineral deposits, estimation of their mineral resources and production costs, and availability and sensitivity analyses. Products include data print-outs of geological and engineering information, discounted- cash-flow rate of return (DCFROR) analyses of individual mining operations, commodity availability appraisals, and analytic services to Government agencies. These products are used in assessing the mineral supply position of the United States: in setting priorities for research aimed at reducing production costs and minimizing adverse environ- mental impacts and regulatory compliance costs of mining and mineral processing operations; and in formulating and evaluating Government policies that affect minerals. Bureau MAP data and analyses have been provided to the executive and legislative branches to aid in consideration of trade, tax, and stockpile policy issues. A study of the economic potential of selected seabed mineral resources supports the regulatory responsibilities of the Department of the Interior in the U.S. Exclusive Economic Zone. Analytic studies of mineral project viability, industry competitiveness, and import dependencies were also undertaken for, or in cooperation with, U.S. and foreign government agencies, industry and trade organizations, and international lending institutions.

Jan 1, 1987

By R. A. Hemstock

AREAS in which the surface de-posits consist of organic material -known in some parts of Canada as muskeg and in Europe, more generally, as peat lands -have long been some of the least rewarding of lands of the north temperature zone. Even in such countries as Great Britain, Holland, and Denmark where a good deal of incentive exists to develop all available land, the use of peat land has been negligible except as a source of fuel. Only recently have efforts shown promise in re-claiming these lands for farming or for forestry. Russia has large areas of peat and use is made of it for power generation. The Russian people have also ?developed a variety of machines for handling peat, which would indicate that they are well ahead of the Wes tern World in their technical and physical ability to solve some of the problems. Certainly in Canada, where there are over 500,000 square miles of muskeg, the economic aspects of this problem are important. This is especially true in considering the shifting emphasis to northern development. Not only is muskeg in possession of great stretches of terrain, thereby rendering it useless for agricultural purposes, but it is apparently moving into forested areas and reducing their productivity. In addition, it lies as a great barrier to movement in the search for and development of such natural resources as petroleum, natural gas and minerals generally. This situation has long been recognized in Canada but only recently have organized efforts been made to study the problems and search out ways of overcoming them.

Jan 1, 1958

By Manish Uttarwar, Rajendra Yerpude

India is the third largest producer of coal and the fourth largest in terms of coal reserves in the world. However, new research quite ironically projects that despite the continuing growth in domestic coal production, the country’s exploding economic growth will position it to be the biggest coal importer by 2020. India’s inability to meet the domestic coal demand is mainly attributed to low rate of production, increasing stripping ratio, non use of appropriate technology etc. of coal mining operations here. Presently Indian surface mines which have to shoulder the onerous responsibility of augmenting the coal extraction rate at an even brisker pace are mulling bigger, better and more efficient operations ensuring commensurate rise in stripping work as well. This mammoth task can be accomplished only by deploying smart technologies. In this perspective, cast blasting of overburden emerges on the horizon as a promising alternative for enhancement of the production and productivity of Indian open-pit coal mines.

Jan 1, 2009

By A. J. Miller, G. R. Brophy

THE Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Grossmann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al .4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be expected that similar results would be obtained. Crafts and Lamont, in their second paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater5 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann's factors underevaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. [ ] More recently W. Steven6 has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were

Jan 1, 1945

The coking coal produced by Utah Development Company in the Bowen Basin is processed by a dual system of dense media cyclones for the 30mm x 0.5mm feed and flotation for 0.5 x 0mm material. The basic metallurgy of these processes will be presented with emphasis on the operational characteristics which are peculiar to coal. Potential areas for process improvement by the application of more sophisticated control systems will also be discussed.

Jan 1, 1978

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By J St George

Much of AucklandÆs transport infrastructure has been developed on surface with little or no consideration of underground options. Current and planned transportation routes are now facing high costs due to land values and increasing environmental resistance to surface development. The option of utilising underground space becomes a feasible investment decision for these links as well as being the only option to develop the rail network within the inner city area. Transportation tunnels offer a quieter, more energy efficient means of getting around with minimal impacts on the surface environment. One of the major impediments to tunnelling is the high construction cost, which is partly related to the risks of encountering unexpected ground conditions and/or the possibility of causing surface ground deformations which could damage structures. The geology of Auckland has had substantial investigation through various studies and projects. The sediments of the East Coast Bays Formation (ECBF) underlie most of the Auckland urban area. It is classified as a soft rock and is a suitable material to tunnel through using either a tunnel boring machine or a roadheader. This paper reviews the limited amount of tunnelling completed in the urban Auckland area, together with the international advancements that have been made in the tunnelling industry. From the known features of the local geology and the problems encountered historically, the likely risks of tunnelling in Auckland are presented and ways in which those risks could be reduced and managed, are discussed. In addition, contractual arrangements between client and contractor are assessed with respect to complicated projects (such as tunnelling), so that the risks can be managed to create efficient infrastructure routes with reduced costs.

Jan 1, 2008

By Massacci P

A review has been made of the studies focusing on methods for the description of grain -size distribution after breakage and, separa- tely, of the degree of liberation of the miner- al species making up the various grain-size classes of comminution products. The purpose of the study has been to de- velop an overall model of the phenomenon which, owing to the very effect of comminution, leads to the formation of grains that are generally of mixed composition. A calculation procedure has thus been de- veloped for the liberation function taken as the assessment of the distribution of mix com- ponents in the products obtained after a commi- nution process. The aim is to identify a func- tion which may, to a certain extent, simulate the variation of the grade-recovery function of an ore in relation to its degree of comminu- tion. The numerical model thus obtained has been tested out on results obtained experimentally.

Jan 1, 1986

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

By S. K. Sahoo, S. K. Sharma, A. Yadav, B. Behera, G. S. P. Singh

A field representative modeling of the gob behavior is critical for the understanding of the associated mechanics of strata behavior in longwall workings. The findings of theoretical models and laboratory tests on the simulated gob material have shown the strain hardening behavior of the gob material. The double-yield material model, which is a built-in constitutive model in FLAC3D, has significant potential to simulate the gob compaction process as it represents materials which undergo irreversible compaction in addition to shear yielding. Apart from this, several researchers have attempted using modified elastic model or applied nodal force in reaction to the strain in the gob area as per the well-known theoretical relations to meet this requirement. Although these models can simulate the mechanical response of the gob for subcritical and critical extraction widths, they do not apply to supercritical extraction width as the gob stress may exceed the in situ stress level in such cases. For overcoming these limitations, a standard approach has been developed and validated in this paper, which can be used for simulating the gob behavior in supercritical longwall workings as well. The complete study is divided into two stages wherein the laboratory scale compression test on the simulated gob material has been numerically replicated to develop preliminary confidence followed by a parametric study of the double-yield constitutive parameters for a rational estimation of their values in different conditions. The calibrated model has been used for verifying its results by plane strain modeling of two different longwall workings, using well-established empirical and analytical findings and field observations. The approach suggested in this study can be used for the efficient modeling of the gob behavior of longwall panels under varying geo-mining conditions without compromising the accuracy of the numerical model. The meticulously validated model can be helpful in rational estimation of stress redistributions around the gob area apart from load transfer on the barrier pillar.

By S. K. Sahoo, S. K. Sharma, A. Yadav, B. Behera, G. S. P. Singh

A field representative modeling of the gob behavior is critical for the understanding of the associated mechanics of strata behavior in longwall workings. The findings of theoretical models and laboratory tests on the simulated gob material have shown the strain hardening behavior of the gob material. The double-yield material model, which is a built-in constitutive model in FLAC3D, has significant potential to simulate the gob compaction process as it represents materials which undergo irreversible compaction in addition to shear yielding. Apart from this, several researchers have attempted using modified elastic model or applied nodal force in reaction to the strain in the gob area as per the well-known theoretical relations to meet this requirement. Although these models can simulate the mechanical response of the gob for subcritical and critical extraction widths, they do not apply to supercritical extraction width as the gob stress may exceed the in situ stress level in such cases. For overcoming these limitations, a standard approach has been developed and validated in this paper, which can be used for simulating the gob behavior in supercritical longwall workings as well. The complete study is divided into two stages wherein the laboratory scale compression test on the simulated gob material has been numerically replicated to develop preliminary confidence followed by a parametric study of the double-yield constitutive parameters for a rational estimation of their values in different conditions. The calibrated model has been used for verifying its results by plane strain modeling of two different longwall workings, using well-established empirical and analytical findings and field observations. The approach suggested in this study can be used for the efficient modeling of the gob behavior of longwall panels under varying geo-mining conditions without compromising the accuracy of the numerical model. The meticulously validated model can be helpful in rational estimation of stress redistributions around the gob area apart from load transfer on the barrier pillar.