Search Documents

By Bailey S, Avraamides J, Jayasekera S

The anodic dissolution of iron from three different Western Australian reduced ilmenites was investigated using the carbon paste electrode technique. A characteristic current-potential diagram, called a cyclic voltammogram (CV), was obtained for each of the reduced ilmenites. The shape of the CV measured for all three reduced ilmenites was strongly time dependent. The effect of electrolyte composition and temperature on the CV of one reduced ilmenite was also investigated. The results suggest that the initial surface of iron in reduced ilmenite is slow to dissolve and that chloride ions and higher temperatures accelerate the dissolution of this initial surface layer. However, after removal of this layer, the dissolution rate was essentially independent of the electrolyte composition and the temperature.

Jan 1, 1996

By B. M. Larsen, K. Heindlhofer

THIS paper describes a relatively simple electrical apparatus that, through the close analogy between the flow of heat and of electricity, enables one to solve quickly and with satisfactory accuracy many complex problems in heat flow. This device, developed in 1935, has proved especially useful in the solution of certain practical problems relating to the design and efficiency of regenerators for an open-hearth furnace or coke oven, yielding within a few hours information that would take weeks or even months to acquire by mathematical1.2 or experimental3 methods of comparable accuracy. Its description now is prompted by growing interest in such analogues, as shown by several recent papers.4.5 The analogy between flow of heat and of electricity appears to have been recognized first by Maxwell who, in his famous Treatise on Electricity and Magnetism (1881) says: The analogy between the theory of the conduction of electricity and that of the conduction of heat is at first sight almost complete. If we can take two systems geometrically similar, and such that the conductivity. for heat at any part of the first is proportional to the conductivity for electricity at-the corresponding part of the second, and if we also make the temperature of any part of the first proportional to the electric potential at the corresponding point of the second, then the flow of heat across any area of the first will be proportional to the flow of electricity across the corresponding area of the second. .. Thus, in the illustration we have given, in which flow of electricity corresponds to flow of heat, the electric potential to temperature, electricity tends to flow from places of high to places of low potential, exactly as heat tends to flow from places of high to places of low. temperature He noted, however, that this analogy is restricted: ... there is, however, one remarkable difference between the phenomena of electricity and those of heat. Suspend a conducting body within a closed conducting vessel by a silk thread, and charge the vessel with electricity. The potential of the vessel and of all within it will be instantly raised, but however long and however powerfully the vessel be electrified, and whether the body within be allowed to come in contact with the vessel, or not, no signs of electrification will appear within the vessel, nor will the body within show any electrical effect when taken out. But if the vessel is raised to a high temperature, the body within will rise to the same temperature, but only after a considerable time, and if it is then taken out it will be found hot, and will remain so till it has continued to emit heat for some time. The difference between the phenomena consists in the fact that bodies are capable of absorbing and emitting heat, whereas they have no corresponding property with respect to electricity. According to this statement the application of the analogy would be limited to problems of steady flow that do not involve heat-capacity effects. In spite of this

Jan 1, 1945

By Bert C. Morrison

In 1961. American Smelting and Refining Company was conducting exploration for lead in southeastern Missouri using several geophysical methods. Electrical methods were used in almost every hole drilled during this period. These methods met with only limited success, with one exception. This paper deals with that exception: An Electrical Potential Method used at a single hole to indicate direction to better mineralization. This method was notably successful in the program.

Jan 1, 1970

By Frank Armstrong

ALL the mining machinery of the Penn Iron Mining Co. has been operated by electric power for several years and when another shovel for stockpile loading was required the advantages of an electric shovel were naturally considered. After considerable study, serious objections suggested themselves the use of a shovel operated directly by electrical apparatus by reason of the complicated control, severe service on the motors FIG. 1.-ELECTRO-HYDRAULIC SHOVEL FIG:. 2-THE SHOVEL AS IT WAS OPERATED CINDER CONSTRUCTION. THE FIRST YEAR. and the heavy surges of current required from the line. It was finally decided to construct an electro-hydraulic shovel using water under pressure to perform all the necessary operations except that of propelling, for which a separate motor was best suited. A car body with boom, dipper handle and dipper of late design, but without any of the steam machinery, was purchased. A motor-driven centrifugal pump, a pressure tank, an air tank, a small air compressor and water cylinders with plungers, pistons and valves, were installed in place of the; steam equipment. Fig. 1 shows this shovel under construction and Fig. 2 shows it as it was operated during the first year, the summer of 1914. The large tank at the back of the car, in Fig. 1, carried air under

Jan 2, 1916

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

By J. Mirza, E. Nicol, J. Lipkowski

Gold passivation in thiosulfate leaching media is a major barrier to its implementation. Addition of Cu (II) into the leaching solution has shown to aid in gold dissolution, but the mechanism by which it acts, and its role in the passive layer, remains unknown. Surface Enhanced Raman Spectroscopy (SERS), in tandem with linear sweep voltammetry, were employed to determine the dependence of leaching currents on mass transport and for fingerprint identification of sulfur species on the surface of gold. SERS leaching experiments were performed using gold nanorod electrodes that showed increased stability compared to other SERS active surfaces.

Jan 1, 2011

By Y L. Ma, M Chen, W Bruckard

With the extensive exploitation and gradual depletion of high-grade copper reserves, the mining industry is paying more and more attention to the hydrometallurgical extraction of copper from lowgrade and arsenic bearing copper ores. Hydrometallurgical processing, such as heap leaching, column leaching and bioleaching, provide a viable alternative to the traditional pyrometallurgy due to its harmony with the environment, moderate capital investment, and low operating costs. However, the slow leaching kinetics of enargite (Cu3AsS4) and chalcopyrite (CuFeS2) remain problematic for commercial leaching practice. The formation mechanism and the nature of the passivating layers during leaching is still a matter of debate in hydrometallurgical research. In this study, the dissolution mechanism of enargite and chalcopyrite in sulfuric acid solution was investigated using a range of electrochemical and spectroscopic analysis methods. Electrochemical oxidation of enargite demonstrated an obvious passivation region from 500 to 750 mV (Ag/AgCl). The formed passivation film was found a n-type semiconductor behaviour, which is different from the original enargite with a p-type behaviour. The results of X-ray photoelectron spectroscopy (XPS) suggested that a nonstoichiometric film Cu(3−x)As(1−y)S4 (x>>y) accumulated on the electrode surface, which accounted for the obvious decrease in current density in the passive potential region. For chalcopyrite, three important potentials of 550, 680 and 730 mV which are related to the formation and dissolution of passivation film were observed based on the cyclic voltammetry (CV) and potentiodynamic polarisation. Raman and X-ray absorption near edge structure (XANES) spectra studies of the chalcopyrite electrodes after being treated under these three potentials indicated a metal-deficient sulfide of Cu1−xFe1−yS2 (y>>x) might be responsible for the passivation phenomenon. Hence, it is concluded that the passivation of enargite and chalcopyrite are similar which are caused by metaldeficient sulfide surfaces although the compositions of the metal-deficient sulfide are different.

Aug 24, 2022

By Ignacio González, Marcos Monroy, Valerie Bertrand, Roel Cruz

Results of an electrochemical study using carbon paste electrodes of pyrite and pyrrhotite samples suggest that the mineralogical impurities associated with these minerals are the determinant factor on their reactivity under alteration systems. These results were supported by mineralogical and leachate chemistry data from leach cell tests run on these samples. Pyrite reactivity decreases in the presence of associated impurities due to a galvanic effect whereas pyrrhotite reactivity appears to be controlled by the formation of a passivating layer, which overcome impurities effect. Electrochemical responses of sulfide-bearing samples provided valuable information on the prediction of ARD generation.

Jan 1, 2000

By Tadao Nagai, Masao Sato

Electrochemical measurements have been carried out in an auto- clave to investigate the electrochemistry of hydrogen precipitation of nickel from acetate buffered solution. After having previously obtained the rate equation for this reaction we have now made a concentrated effort to explain the rate equation electrochemically. A saturated NaC1-type Ag/AgC1 reference electrode has been improved so that it can be used in an autoclave. Polarization curves for the reaction, [H2=2H+ + 2e,] on nickel electrode were measured in solutions free from nickel ions at 185°C, and the parallel curves were obtained by changing PH2 and pH for normal and reverse reactions, respectively. Polarization curves in nickel solutions were complex, probably because the potential of hydrogen electrode is close to that of nickel and of the nickel surface altered during polarization. Then the nickel electrode potential and the reaction rate were measured simultaneously during pressure reduction at various hydrogen pressures and at various nickel concentrations. The reaction rates in terms of current density were plotted to obtain the local polarization curves for reactions Ni2+ + 2e ? Ni and H2 ?2H+ + 2e. The anodic and cathodic local polarization curves exhibit potential dependency. Therefore it is likely that the pres- sure reduction can be regarded as a coupled electrodes reaction.

Jan 1, 1973

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc's open circuit anode potential."

Jan 1, 1990

By M. J. U. T. Van Wijngaarden

SYNOPSIS The corrosion characteristics of a new steel, 14Cr, which is a modification of the well-known 3CR12, in aqueous sulphate solution were studied through polarization diagrams and a computer analysis based on the polarization¬resistance technique. It was found that the corrosion rate of 14Cr steel is independent of pH for pH values above 6, but, below a pH value of 4, the corrosion rate increases sharply with decreasing pH. In air-saturated solutions of neutral and mildly alkaline pH, the corrosion rate is approximately 60 µm per year. The 14Cr steel shows a twentyfold improvement in corrosion resistance over that of 3CR12 in sulphate solutions at pH 2,0. This is considered to be due to the beneficial effect of its higher chromium and nickel contents.

Jan 1, 1985

By Q. Zhang

The flotation behavior of jamesonite was investigated with ethyl xanthate as a collector. It has been shown that jamesonite has good floatability from pH 2 to pH 12, and relatively poor floata-bility at pH>12. The flotation of jamesonite was also dependent on pulp potential at certain pH val-ues. The potential-pH range for jamesonite flotation was established. The FTIR spectroscopy analy-sis and XPS measurement showed that the major adsorption product of ethyl xanthate on jamesonite was lead ethyl xanthate and antimony ethyl xanthate. The intensity of the FTIR signals of metal ethyl xanthate adsorbed on jamesonite and the flotation response of jamesonite were correlated with pulp potentials.

Jan 1, 2014

By J. G. Peacey, G. Csicsovszki

The target of this study was to clarify the role of lead on the dissolution of gold in the (NH4)2S2O3-Cu leaching system via chronopotentiometry, linear sweep voltammetry and chronoamperometry. It was found that the dissolution of gold was significantly increased with lead concentration up to 10 mg/1 Pb in the system of 0.1 M (NH4)2S2O3 and 50 mg/1 Cu. \/oltammograms suggested that the anodic dissolution of gold was virtually independent of lead concentration in the range of 1-10 mg/1 in 0.1 M (NH4)2S2O3 solution while in solutions containing copper as well, addition of lead increased the anodic dissolution of gold.

Jan 1, 2011

By M. J. Nicol

An electrochemical investigation of the dissolution of copper, nickel, and copper-nickel alloys in ammonium carbonate solutions by M. J. NICOL, Ph.D., B.Sc. (Hons.) (Wits.) (Visitor) The dissolution of copper and nickel in ammonium carbonate solution was studied by techniques involving electrohemical anodic dissolution and ring-disc electrodes. The rate of oxidation of both copper and nickel by copper (11) was shown to be controlled mainly by diffusion to the surface. Variations in rate with changes in copper (11) concentration, agitation, pH, ammonia concentration, temperature, and copper (I) concentration were investigated and rationalized in terms of their effects on the electrochemical half-reactions involved. Evidence was found for the passivation of nickel and nickel-copper alloys of more than 50 per cent nickel.

Jan 6, 1975

By L Dzinza, K C. Corin, M Tadie

The recycling of process water comes with increased electrolyte concentrations that affect water quality, which may in turn affect the flotation performance of valuable minerals (Hirajima et al, 2016). Electrolytes such as Ca2+, SO4 2- , Mg2+ and S2O3 2- have been surmised to have an impact on the action of flotation reagents such as collectors (Ikumapayi et al, 2012). Xanthate collectors are known to play a significant role in imparting hydrophobicity on mineral surfaces to enhance their flotation. The interaction between minerals and xanthates is well known to be electrochemical in nature. Such redox processes may be elucidated by electrochemical techniques. Since the mechanisms involving the interactions between electrolytes in process water with sulfide minerals and the subsequent adsorption kinetics of collectors are not well understood, this study therefore aims to provide fundamental knowledge to unpack the mechanisms involved when electrolytes interact with Platinum Group Minerals (PGMs) and how these interactions may affect xanthate adsorption. The interaction of sodium iso-butyl xanthate (SIBX) in the presence of electrolytes at increasing ionic strength was investigated by rest potential measurements, to explain the impact of electrolytes on the adsorption of SIBX on PGMs in the flotation process. Rest potential measurements for PdTe2 and PdS were conducted in an air saturated 0.05 M di-sodium tetraborate decahydrate solution, in the absence and presence of SIBX and electrolytes. It was found that the existence of sulfide and telluride on palladium affects the mechanisms in which electrolytes interact with Pd mineral surfaces. An increase in the ionic strength of Na2S2O3, CaCl2 and MgCl2, increased the interaction between the salts and PdS, thus decreasing the extent to which SIBX interacted with PdS. An increase in ionic strength for Na2S2O3 increased the interaction between Na2S2O3 and PdTe2 and therefore decreased the extent to which SIBX interacted with PdTe2. Other salts investigated in this study increased the rate of oxidation of PdTe2 with an increase in ionic strength thereby enhancing the interaction of SIBX and PdTe2. This study has shown that mineral type, electrolyte type and concentration all have an impact on the mechanisms that result in the adsorption of SIBX on PGMs.

Aug 24, 2022

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By P. E. Richardson, N. P. Finkelstein, Z. Chen

The large band gap and insulating properties of sphalerite have limited the application of standard electrochemical techniques for studying its reactions with flotation reagents. This problem has been overcome by developing electrodes that rely on the surface conductance produced when sphalerite is activated with copper or other heavy metals. A brief exposure of the mineral in copper sulfate solutions results in electrodes that exhibit significant electrochemical activity characteristic of copper sulfides. Voltammetry studies conducted on sphalerite activated in 10-4 M CuS04, solutions at pH 4.6 provide information on both the amount and the nature of the activation product(s). It is shown that copper activation is strongly dependent on the electrochemical potential applied during activation. Activation at potentials increasingly negative of the rest potential causes a progressive increase in the amount of copper on the surface; activation at potentials positive of the rest potential decreases the amount of copper on the surface. The results indicate that both the kinetics of copper uptake and, possibly, the chemical composition (stoichiometry) of the activation product are controlled by the electrochemical potential.

Jan 1, 1995

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By Z. M. Zheng

Cyclic voltammetry, potential step, and ac impedance techniques were applied to study the electrochemical reaction of arsenopyrite in chloride solutions. The relationship between anodic current density and time in potential step measurements indicates that the oxidation of arsenopyrite is irreversible. The results of the constant potential coulometry show that the stoichiometric factor of the total electron involved in the overall reaction is 14. It is proposed that the dissolution of arsenopyrite is retarded by coverage of sulfur produced in the reaction as an intermediate product. The measured results of ac impedance strongly support the proposition. The proposed reaction mechanism also explains satisfactorily the charging current density and Tafel slopes measured in potential step measurements.

Jan 1, 1995

By Gerhard Derge

THE chemical and physical properties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use, These processes are carried out at high temperatures and involve such complex chemical systems that fundamental scientific knowledge of the properties and behavior of these slags is inadequate. Various hypotheses have been proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenck1 and the recent papers of Chipman and co-authors.2-5 Another proposal is that these compounds dissociate by completes or partial ionization, the evidence for which has been reviewed by Martin and Derge.7 Whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: I, Studies of solidified slag samples by X-ray diffraction, petrography, and similar methods that can be used at room temperature, The correlation of this information with the high-temperature properties of the molten slag is uncertain, 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature, However, even these data present problems of interpretation because they require a complete knowledge of the metal phase, 3, Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret, Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information, The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems CaO-SiO2 and CaO-A1203-Si02 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1946