Search Documents

By George P. Schivley

When drilling blast holes, with roller cone bits, a phenomenon known as drilling vibration can occur. It is characterized by either axial or lateral modes of periodic motion of the drill pipe; superimposed on the time-average angular motion of the drill pipe provided by the drill rig rotary head and the vertical motion associated with the penetration rate of the tricone bit into the rock being drilled. This periodic motion can be very severe and, if appropriate action is not initiated by the drill rig operator, could lead to structural damage to the drill rig. Ultimately, the occurrence of drilling vibration limits the productivity potential of a rotary drill.

Jan 1, 1997

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By H. Dean

"Mine hoisting machinery, of which wire rope is an essential part, is developing, in Canada as well as in other parts of the North American continent, into highly sophisticated equipment. Heavier payloads are now required to be raised from steadily increasing depths at higher rates of speed and production. These hoisting conditions have, of necessity, brought about a major change in the production of steel roping wires and the wire ropes manufactured from them.Operators and designers of hoisting equipment are requesting a very much more efficient ratio of strength to weight in hoisting ropes, so that heavier loads may be raised from greater depths by ropes which will provide a predeterminable life span on which the operator may depend.The cost of wire rope to the operator is very low indeed, usually less than $0.01 per ton of payload, but the cost of unexpected shutdown periods, due to rope maintenance or change, can be extremely high -particularly in operations where a continuously high rate of production is an absolute necessity. Mine hoist ropes with a higher strength to weight ratio are now being made and used in some areas of Canadian mining, and a general understanding of the performance we may expect from them is required."

Jan 1, 1968

By Milton Gomez, Nico Sutmoller

Low-density cellular concrete (LDCC) was first introduced to the market in the early 1900s and since then has made continuous technological advances. There are two primary types of LDCC: permeable and non-permeable. Both types of cellular concrete offer advantages in different types of geotechnical engineering applications. Because of its unique characteristics of low density, high compressive strength, and high fluidity during placement, LDCC offers an effective solution for a wide variety of engineering applications, and in many cases provides a more cost-effective, labor saving alternative to traditional fill materials. This paper will review the history, characteristics, and technological advances of LDCC, highlighting multiple real-world case studies that showcase the high-performance capabilities of both permeable and non-permeable LDCC.

Dec 1, 2022

By J. W. Rinard

This paper is intended to introduce "non engineers" to one of the more misunderstood pump performance parameters, NPSH (Net Positive Suction Head). This basic presentation and resultant review should provide a practical understanding of NPSH and what its importance is to pump operation and reliability.

Jan 1, 1996

By Paul Worsey, Seokbin Lim

In many high explosive applications, the explosives are covered or clad by a metal. This metal cover may serve a variety of purposes including: 1) to protect and prevent the disturbing or misshaping of the explosive during its transportation, handling and use, 2) in many military applications the cover material itself is used to provide a required effect, for example, the shrapnel from grenades, the metallic liner of shaped charges, and the confinement of explosives so they perform optimally, and, 3) in civilian applications in the use of well perforating shaped charges and linear shaped charges used for the demolition of steel structures such as bridges. For these reasons the interactions between the explosives and their covering materials are of great importance in understanding the performance of these devices.

Jan 1, 2005

By Edgar Bain

SUMMARY THE results of an enquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration 'are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research Laboratories. All the compositions studied contained carbon in amount comparable to commercial alloys.

Jan 3, 1927

The Mineral Resources Act 1989 was assented to on 25th October, 1989 after more than two years of consultation and negotiation between Government, the mining industry and other affected parties particularly the major rural organisations.The legislation proposes major conceptual changes in a number of areas and adopts a totally new approach to the definition of land and the mechanisms available to the mining industry for accessing such land.Unfortunately the passage of the legislation through Parliament coincided with the lead-up to the State election. Ultimately it became an election issue generating much adverse comment in the media particularly from rural and landholder groups. It was obvious that much of this anti-mining propaganda resulted from a lack of understanding of the legislation and the benefits that flow to the majority of landholders as well as the mining industry.It is essential that the contents of the Mineral Resources Act be thoroughly understood by all parties. Only then will all the State's resources be able to be developed in a multiple land use environment.This paper outlines the philosophy behind the new Act and the more important provisions contained therein.

Jan 1, 1990

The brown coal resources of the Latrobe Valley, which include over thirty thousand million tons of coal suitable for open cutting, provide the main source of fuel for the power generation for the State of Victoria. They also provide the basis for the development of a supply of cheap hard fuel for industrial and domestic use, and for the development of the Lurgi process for manufacture of town gas for most of the State. The production of hard char for metallurgical processes and liquid hydro carbons will each, no doubt, play its part in the industrial growth that will be based on these resources.The State Electricity Commission of Victoria, which has been allocated the task of developing these deposits since the early 1920's, is faced with problems of economic selection of deposits for development, and excavation and transport of huge tonnages of coal and overburden-in this year, 19'59, about 12,000',000 tons of brown coal will be won, and over 7,000,000' cu. yd. of overburden will be removed in the four open cuts operated by the Commission; by 1967, eight years from now, the demand will have doubled.This paper deals with the nature and importance of various factors effecting the planning of the development of these resources. It is in essence an introduction to the papers by C. S. Gloe, H. C. G. Rodgers and J. M. Alexander, also being -presented at the Institute conference in Victoria in August, 1959.INTRODUCTIONIt is the intention in this paper to define the factors that come under consideration in the planning and development of the brown coal fields in the Latrobe Valley, whose exploitation by the State Electricity Commission of Victoria was initiated almost 40 years ago. It is proposed to enumerate, and in sorile cases evaluate, the physical and economic criteria that play their part in determining planning for the future.

Jan 1, 1960

By Francis Lucas

A microscope objective of given numerical aperture, whew used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability-the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise whew the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500, µµ and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.65 N. A. are wow an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Köhler and Dr. M. Vow Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 µµ which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 6, 1926

By Matthias Rheinlander

The paper will describe Virtual Design and Construction (VDC) as a tool which will enable us to build a project ?virtually? on a computer before constructing and operating it in the real world. VDC computer models are built, using information from various sources including survey, 3D laser scanning, CAD and GIS to represent the project and its components in a coordinated and consolidated infrastructure model. This model is reviewed and evaluated by, and shared among project teams including owners, con-tractors, designers, engineers, construction managers, stakeholders and operators. It allows teams to fix costly design and construction issues before construction on site. Benefits and lessons learned from global projects will be discussed

By Stefan Swartling, Rudy Lyon, Donald A. Bruce

"Since their first production application in Sweden in 1995, water-powered, down-thehole hammers (WDTH) have been used throughout the world in many different drilling applications, total lines, over 25 million lineal meters of drill hole. This paper reviews the history and principles of down-the-hole drilling (DTH) in general with both air and water, before focusing on the details of WDTH hammers. A summary of the numerous and considerable advantages of WDTH drilling is provided, with particular emphasis on their superior productivity, smaller deviation, applicability in sensitive/urban conditions, environmental protection and much reduced energy requirements.HISTORICAL PERSPECTIVE ON PRODUCTION DRILLING METHODSAir-flushed drilling with top hammers began in the mining industry in Sweden in 1873, while down-the-hole (DTH) drills, again with air flush (and activation) became operational in 1950. During that same time interval, Simon Ingersoll had patented the first steam-powered, top hammer rock drill to provide higher productivity in blast hole drilling. It is well known that water, as an activating, flushing and cooling medium, has many significant advantages over the use of air. However, it was not until 1973 that top hammer systems (either air or hydraulically activated) for larger rigs were adapted to the use of water flush, typically via “under the head” swivels.The concept of a water-powered, down-the-hammer (WDTH) had been explored prior to G. Drill acquiring the original patent from Atlas Copco in 1988. LKAB, a huge underground mining company owned by the Swedish Government and providing about 90% of the European Union’s iron ore, purchased G. Drill in 1991 and encouraged the commercial development of the WDTH. The first full-scale WDTH production works were carried out for LKAB in 1995, since when over 25 million lineal meters of drilling have been recorded in both underground and surface applications.In 2001, G-Drill was renamed Wassara, which today still holds the worldwide patents for WDTH technology. Regarding North American usage, the first significant application was by Advanced Construction Techniques (ACT) Ltd. during the test grouting program conducted for the U.S. Army Corps of Engineers at McCook Reservoir, Chicago, in 2002. Since then, WDTH has become the tool of choice for specialty drilling and grouting contractors on dams and other major structures throughout the U.S."

Jan 1, 2015

By O’Brian. Daniel T.

Ore reserve determinations supporting property appraisals and economic analyses leading to investment decisions typically require many repetitive calculations. Computers have become well-accepted tools for accomplishing these computations, and are partly responsible for the development of new evaluation methods during the last decade. Excellent descriptions of manual ore reserve may be compared with current computer reserve methods1,2 in North America2 and South Africa3. A comparison indicates that computers are used in two cases: a) when a cost savings can be achieved by the simple conversion of a manual method to a computer processed equivalent, and b) when the quantity of data and ore reserve estimation purpose justifies adoption of a complex ore reserve computational method not feasible on a manual basis. Ore reserve computations essentially consist of using sample data and a mathematical method to arrive at an estimated geometry, tonnage, and grade for a mineral deposit. The mineral deposit is then subdivided, if necessary, into ore and waste components. This separation is based on economic factors which may be explicitly introduced in the computation or incorporated in a numerical cutoff grade4. Computer methods for accomplishing these tasks are presented in three papers. "The Use of Contour Surfaces as Predictive Models for Ore Values" discusses the requirements for a satisfactory value prediction model and the importance of considering auto -covariance. A weighted moving average method is described and compared to other mathematical surface development methods. In the second paper, "The Applications and Limitations of Computer Techniques in the Evaluation of Hypothermal Tin Lodes," particular problems encountered in estimating geometrically erratic economic deposits with a low valuable mineral content are documented. Economics and probabilistic concepts are introduced, allowing a comparison of risk and speculative value for a deposit. Economic considerations are integrated with ore estimation techniques in the third paper, "Method of Calculation of the Iron Ore Reserves in the Lorraine Deposit." The prediction model

Jan 1, 1969

By Harrison R. Cooper

Computer process analysis and control techniques are overcoming major hurdles to acceptance in the mineral industry. With the growing list of new advances characteristic of a rapidly maturing discipline, management of the companies on the leading edge are keenly aware of the advantages of using computer methods in process applications. Significant advancement is already evident in such technical areas as operations research, mathematical modeling, statistical methods, and computer-based procedural techniques. The early advances during the past decade are already documented in prior symposium proceedings of this series. Thus, the currently active areas of the advancing technology are emphasized here. This section deals with applications in pyrometallurgical and kiln processes. The two sections which follow deal with concentrating operations from two points of view: 1) mathematical modeling, and 2) on-line control. In the metallurgical field, emphasis on developing effective process computer applications for the steel industry began in the late 1950's. Simulation techniques also received substantial attention. The steel industry was soon joined by the cement industry in the development of computer methods for process applications. Computers were in use for feed-material blending and kiln control in the early 1960's. Computer development in other pyro processes, such as aluminum reduction and glass-making, also marked significant advances by the mid 1960's. Aluminum smelter potline control is a nearly universal application at this point, and the development of glass furnace computer process control represented a recent important technical advance in digital control techniques. Steel Hot strip rolling was the earliest significant process computer application in the metallurgical industry. Computer control of rolling mill operations is now a steel mill standard component, particularly in plants newly placed into production. 1, 2 Initial computer installations principally carried out procedural routines in setting mill clearances for production lot control. Recent developments are leading toward feedback control based on mathematical model techniques. 3

Jan 1, 1969

By David B. Morris, Paul I. Eimon

Computer-assisted data storage and retrieval in the geosciences is coming of age. A growing awareness of the need of the geological and mining community for effective access to existing data has triggered studies and development programs on many levels; governments, professional societies, industrial concerns, and the academic world are all active in this field. Developments in the past decade in computer hardware and software lend hope to the geoscientist searching for a means of expediting the flow of data. The new concern of the earth sciences coming together with the blossoming child of technology, computing, has led to serious study of the geoscience information problem. Active system development is under way in several areas. The papers presented at this Symposium effectively sample the spectrum of present day activity in machine-based geologic data storage and retrieval. These papers show the reader where the action is in this field today. Both long-range studies and plans and operational systems are discussed. Several studies and research efforts have been undertaken on a national or international scale. Robinson discusses the activity of the international geological community in these Proceedings. He speaks from a position of authority as Chairman of the International Union of Geological Sciences' Committee on Storage, Automatic Processing and Retrieval of Geological Data. A study of a "coordinated information program for geological scientists in the United States" documented by Smith, et al.1 proposes a "long-range information program ... responsive to the entire geosciences community . . . (to) draw on the best of large-scale information systems technology." The European geologic community is embarked on project Geosemantica 70, started at the Ecole Nationale Superieure des Mines de Paris. Dixon discusses some results of this work in a following paper. The Canadian study of geological data storage and retrieval on a national scale is reported in a volume edited by Brisbin and Ediger.2 The Canadian report presents detailed recommendations for recording and coding geologic data for automatic process-

Jan 1, 1969

By Harrison R. Cooper

This section will outline procedural, statistical, and model applications developed for specific problem solving and for specific applications in beneficiation processes. Iron Ore Processing Introduction of taconite as a basic raw material in the iron ore industry took place with application of high order technical resources for process development and engineering. This investment of resources encouraged computer utilization to maximize efficient use of capital. From this recognition, process control computers have been installed for operations use in the major taconite plants of the iron range. One of these installations, the Minntac Division of U. S. Steel at Mountain Iron, Minnesota, is described in the paper by Chase in these proceedings. Other computer techniques used in taconite processing are outlined by Tuttle, Ahlquist and Carlson, representing Erie Mining. In this volume Tuttle, et al. describe statistical methods for development of information in taconite beneficiation. Statistical methods used in iron ore processing are described by Volin in treating flotation data as outlined in prior proceedings of the symposia and in other publications. 1,2,3 Industrial Minerals The use of linear programming for feed blending at the Carlsbad operation of International Minerals and Chemicals was outlined by Nunnekoven in 1963.4 Subsequent application of this procedure at the Kingston phosphate operation in Florida was described by Loper. Continued development led to installation of an on-line computer in the Kingston plant which reached operational status in 1967.6,7,8 Application of an on-line computer to industrial mineral production accomplished at Kingston is regarded as a milestone in computer use development. Following this achievement, the Cominco potash beneficiation plant near Saskastoon in Canada was automated by installation of an on- line computer programmed to carry out direct digital control functions to effectively operate the plant by process computer. The procedures used in the Cominco operation are described by Madge in this volume. Development of a mathematical model

Jan 1, 1969

By R. V. Ramani

In a 1985 seminar, we were told that overoptimism abounds in Artificial Intelligence (AI), that A1 is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity.(e.g: machine or program) to be intelligent. According to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way. The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and software along with new insights into the ways in which we store knowledge and use it for problem solving has enhanced the potential for the creation of intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confined by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.

Jan 1, 1989

By R. V. Ramani

It is common knowledge that there is an endless stream of possibilities, proposals, and projects - each representing a demand on available capital - for improving the mining company's performance measure. It is true that these proposals go through an increasingly stringent evaluation process as they move up the echelons of management for approval. Therefore, there is every reason to expect that a proposal or project accepted for deployment will make a substantial contribution to the organization's performance. The reality, too often, is otherwise. Castle (1985) reveals some significant insights into the difficulties in predicting the performances in the mining industry. A sample of eighteen mining ventures, which have been developed over the years, was selected by Castle to illustrate the problems. The actual performances were compared with the original projection. The sample encompasses both surface and underground mines, a large number of commodities, and a wide geographic distribution. The experiences in these mining projects were analyzed through answers to four specific questions.

Jan 1, 1989

By R. V. Ramani

"In a 1985 seminar, we were told that over-optimism abounds in Artificial Intelligence (AI), that AI is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity (e.g. machine or program) to be intelligent. According .to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way.The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and .software along with new insights into the ways in· which we store knowledge and use it for problem solving has enhanced the potential for the creation ~f intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confirmed by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.AI applications are categorized into several distinct areas such as Natural Language Processing, Speech Recognition and Synthesis, Expert Systems, Robotics, Machine Vision, etc. Of these practical realizations, Expert Systems (ES) has the greatest potential for meeting the decision-making needs of the manager in the ever-growing complex scoio-technical systems. Prof. Feigenbaum, an expert and leader on expert systems, has defined Expert System as"" ... an intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for their solution. Knowledge necessary to perform at such a level, plus the inference procedures used, can be thought of as a model of the expertise of the best practitioners of the field."""

Jan 1, 1989

By Daniel T. O’Brian

Mineral exploration activities are benefiting from new interpretive techniques which have become economically practical with computers. Government agencies, educational institutions, and industry have each contributed research and development efforts for improving the mathematical analysis and graphical display of exploration data, resulting in operational aids not foreseeable a decade ago. Progress has been worldwide and is expanding rapidly. Books 1-10 are supplementing the periodic literature, at least one abstracting service is now active, 11 and an association has recently been formed to encourage and publicize advances in this field. 12 With the diversity of applications, only partial coverage of the subject can be made at any single symposium. Four of the six papers in this section report on the current state-of-the-art in selected areas of interest: graphics, time-sharing, mathematics, and economic analysis. The remaining two papers are descriptions of advanced statistical techniques for gaining additional information during exploration, and illustrate methods which will become more commonly applied in the future. "Computer Graphics: A New Tool for Exploration and Mining" describes the use of a computer and accessory equipment as an information retrieval device, graphically merging and displaying pertinent information for visual inspection and interpretation. This is a rapid means of studying information which has been pre-stored in a form accessible to the computer. Time-sharing is a means of achieving a comparable rapid response when calculations are being performed. The paper, "Some Applications of Time-Sharing in Mining Geophysics," describes the experience of one company using a time-sharing facility for geophysical computations. Another paper on this subject, stressing mining applications, has recently been published. 13

Jan 1, 1969