Search Documents

By R. J. Brison, R. D. MacDonald

This chapter is written primarily from the standpoint of development of flotation processes for treatment of specific ores. However, most of the principles and techniques discussed are equally applicable to other forms of applied flotation research such as improvement of procedures in existing plants and development of new reagents or methods without reference to specific ores. Because it is not possible to cover this subject in detail here, much of the material presented is in the form of a guide to the literature, with emphasis on readily available, English language publications. Details are included only if considered to be widely applicable or not readily accessible in the literature. Related subjects which are covered elsewhere in this volume, such as flowsheet design and statistical techniques, are not emphasized in this chapter. The material presented is intended primarily for those familiar with the theory and practice of flotation, but with limited experience in applied flotation research. It may be of value to the experienced investigator as well, by calling to his attention some useful viewpoints or techniques that he may have overlooked. It has often been said that flotation is more of an art than a science. In- deed much of the knowledge of flotation behavior is empirical. However, the unsystematic, artisan approach to flotation problems results only in an ac- cumulation of unrelated data. Like any other physical or chemical process, flotation is amenable to investigation by systematic experimental methods. The experiments should be based, as far as possible, on an understanding of the natural laws that govern the process and on good experimental procedures. SAMPLING OF A DEPOSIT In working out a flotation process for a mineral deposit, no step is more important than that of obtaining a suitable sample or samples. Experimental procedures cannot compensate for the lack of a representative sample. Methods of sampling a deposit have been published elsewhere,l-4 but a few points are of special importance from the standpoint of flotation. First, the sample should be representative of the deposit, not only in respect to chemical composition, but also in respect to mineralogical composition and degree of dissemination of the valuable minerals. To help ensure

Jan 1, 1962

By Henry F. Hebley

THE solid fuel industry, especially that branch represented by bituminous coal, is gradually becoming aware of its ? paramount importance in a world where there is an ever increasing demand for the products of a mechanical age. In practically every process of manufacture, the necessity for energy in some form is being multiplied. Some of that prime energy is derived from water power-hydro-electric schemes, flood control schemes, etc. - but often the electrical energy thus developed is generated at great distances from the load centres, requiring long transmission lines with consequent transformer and transmission losses. A few plants have harnessed the tidal power of the seas and one has harnessed the energy of the wind in a modern manner. All of these schemes are dependent on certain natural geographical, hydrographical, and physical advantages of terrain, as well as an adequate area of consumption of the energy developed. If flood control is the primary object, then power generation is a by-product; and the economics of large capital expenditure on power generating equipment must be considered in that light.

Jan 1, 1945

By Y. Tao

The features of the teeter bed separator and its application in the coarse slime separation of Chengjiao coal preparation plant were discussed. The relationship between the coarse slime separation efficiency by TBS and the particle size were studied, and the influence of using TBS on dense medium consumption and oil consumption were investigated, it increased the clean coal yield and the comprehensive recovery of the whole plant, and brought huge economic benefits to Chengjiao coal preparation plant.

Jan 1, 2011

By Thiann R. Yu, William J. Quesnel

At Kidd Creek, the annual production of 4.5 million tonnes of ore has been achieved primarily with sublevel blasthole stoping. This mining method has allowed underground operations to meet the designed production capacity while maintaining an outstanding safety record. To achieve this goal, rock mechanics principles have been integrated into each facet of mining in the planning stage, in the production stage, and in various stages of ground support. This paper evaluates the two adopted mining sequences based on ground stress patterns, blasting control, ground reinforcement, backfill support, and numerical modelling for stope stability at the mines.

Jan 1, 1984

By Malcolm T. Wane

The subject matter of this paper, "Applied Rock Mechanics?," has its genesis in a recent field trip taken by the author. A more or less standard question asked at the mines visited was "How are you using the principles of Rock Mechanics to assist you in maintaining an efficient, safe, and competitive mining operation?" The question was couched in a number of different forms, but the intent was to determine whether or not a general theory based on reason and the scientific method was applied or whether the alternatives of tradition, intuition, ?common sense', revelation, ?shotgun methods' or authoritarianism were invoked. Perhaps two responses to this query will be illustrative of the general nature of the replies. At operation XYZ an extension to the known ore body has been found. The extension is of large enough size and grade that a mining scheme using load-haul-damp techniques is envisaged. Since this represents a departure from the present mining scheme, questions have arisen regarding pillar sizes, room and entry sizes and possible support requirements. A task force has been set up to expeditiously plan for these things and write the necessary specifications and requirements. The fundamental question was posed to members of this group.

Jan 1, 1971

By Thomas J. Rudolphi

Efficient transport of bulk materials by belt conveyor systems is an important engineering design issue, especially as conveyors become longer and power requirements increase. It is well known within the industry that the parasitic energy loss of a belt conveyor, due to the indentation of the idlers into the belt backing material can be upwards of half the total energy required to drive it on a horizontal flight. Other loss sources includes the rolling resistance of the idlers, belt/roller misalignments, material trampling, frictional and acceleration losses on loading, etc., but energy absorbed by indentation of the belt backing as it passes over each successive idler is the dominant power consuming factor. INDENTATION LOSS MODELS Models to predict the rolling resistance of a cylinder (idler) on a viscoelastic foundation (backing material) have been available for some time. As a contact problem, it is nonlinear (contact length or indentation depth is a dependent on the load and vice versa) in load/deformation response. Rubber backing material is generally assumed to behave as a linear viscoelastic solid, even though it is known that most rubber compounds retain linearity only at very low strains. Because completely general solutions are impossible, practical solutions require simplifying assumptions. Those assumptions relate naturally to two separate pans of any analytical model: I. The deformation model-aspects of the problem relating to the geometry, boundary conditions and kinematics of how the material deforms. 2. The material model-aspects of the problem relating to the material properties, or constitutive relationships, i.e., the stress/strain relationships.

Jan 1, 2008

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By J. W. Merks

Applied statistics provides scores of powerful tests and techniques that are widely used and abused in science and engineering. The variance is the basic measure for variability, precision and risk. The formulas for the variances of the arithmetic mean and the weighted average are derived from the variance of a general function, as defined in probability theory. The requirement of functional or mathematical independence in probability theory translates into the concept of degrees of freedom in applied statistics. Geostatistics is the only variant of statistics in which functional dependence and degrees of freedom are irrelevant. This paper examines whether such basic elements of probability and statistics can be ignored with impunity.

Jan 1, 1998

By J. W. Merks

Applied statistics provides scores of powerful tests and techniques that are widely used and abused in science and engineering. The variance is the basic measure for variability, precision and risk. The formulas for the variances of the arithmetic mean and the weighted average are derived from the variance of a general function, as defined in probability theory. The requirement of functional or mathematical independence in probability theory translates into the concept of degrees of freedom in applied statistics. Geostatistics is the only variant of statistics in which functional dependence and degrees of freedom are irrelevant. This paper examines whether such basic elements of probability and statistics can be ignored with impunity.

Jan 1, 1997

By Mutton B. K

A systematic approach to the collection, presentation and application of structural geology data is employed in the extraction of narrow en echelon Ag-Pb-Zn orebodies by rut and fill stoping at Mount Isa. The aim is to locate, document and predict areas of adverse ground thereby enabling adequate ground support to be installed in advance of production mining. The important structural features are identified and their relevance illustrated by case histories of previous failures. The methods of collection, documentation and application of data are discussed.

Jan 1, 1977

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005

By A. Taylor, J. Shelegey, H. Sullivan, J. Doucet

"Historically, performance at Vale’s Clarabelle Mill was measured by Mill throughput and Mill recovery. After the economic collapse in 2008, a series of reviews were performed to drive improvements in business efficiency. These identified that product quality (e.g., concentrate grade, variability in concentrate grade) had a profound impact on downstream processes and suggested that improved control of these parameters would generate the greatest value for the customer (the Copper Cliff Smelter) and the company (Vale). Consequently, a movement was initiated to transform the Mill operating philosophy to consider customer needs as paramount. Systems and strategies used to drive the transformation are described. In 2011, an unexpected furnace failure resulted in decreased capacity at the Copper Cliff Smelter. In response, a two-stage change in production strategy was developed at Clarabelle. The first stage was to modify the ore blend feeding Clarabelle so that the concentrate grade could be significantly increased with minimal impact on recovery. The second stage was a circuit modification to ensure the elevated concentrate grade could be sustained. Execution of the first stage was complete five days after the failure and the second stage was complete within 10 weeks. Steps involved in each stage are outlined and the overall benefits are presented.INTRODUCTION Clarabelle Mill is located in Copper Cliff, Ontario, Canada (approximately 350 km north of Toronto). The Mill treats copper (Cu) and nickel (Ni) sulphide ores. The primary diluents are pyrrhotite (Po) and non sulphide gangue rock (Rk). The process description of the circuits at Clarabelle is documented in the paper by Taylor, Doucet, Blanchette, Barrette & Lawson (2012) in this Proceedings and will not be repeated. The Mill treats ore containing Cu, Ni and platinum group elements (PGE’s) and produces two concentrates; a Cu concentrate and a bulk Cu/ Ni Concentrate (referred to as nickel concentrate). The Cu concentrate is sold to market while the Ni concentrate is thickened at the Mill and pumped to Vale’s smelter complex in Copper Cliff Ontario for further processing. Since commissioning in 1971, Clarabelle Mill has undergone many circuit changes to suit the changing needs and wants of our customers, both internal and external. The Mill processes ores of varying quality, based on mineralogy and size and until 2009 the Mill daily performance was primarily based on throughput. The second key performance indicator (KPI) of “good” or “bad” performance was quality of the concentrate and third; Mill metal recoveries. There were other plant level KPIs such as flotation feed grind size, slurry densities and mass flows to the separation circuit, but for the most part each day was good or bad depending on how many tons were processed through the Mill."

Jan 1, 2012

By G. L. Mowrey

One of the critical parameters of any automated coal mining system is the ability to only cut coal and not the rock / waste surrounding it. To do this the system must be able to detect where the coal-rock/ waste interface is. The U.S. Bureau of Mines is investigating a new approach to vibrational coal interface detection (CID) by utilizing an adaptive signal discrimination (ASD) system to perform feature extraction and classification of complex vibrational signals. Accelerometers, geophones, and piezoelectric films are mounted on mining machines and/or strata and are used to monitor vibrations produced during mining operations. Selected data are digitized and the ASD system is trained on known types of vibrations (e.g., "cutting coal" and "starting to cut roof"). A signal classifier is then generated which can be used to identify unknown waveforms. The ASD system can be retrained if mining conditions change significantly.

Jan 1, 1990

An atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) on arsenopyrite surface in solutions. AFM images show that the collectors adsorb on arsenopyrite surface in patches at pH 6. Increasing the chemical dosage will increase the adsorption density of the patches on mineral surface. The increased probe-arsenopyrite adhesion measured in PAX solutions at pH 6 is attributed to the adsorption of the patches, suggesting the hydrophobic nature of the patches, which is likely the oily dixanthogen. It is also found that arsenopyrite is reactive in water in the presence of air. At a high pH with the addition of Ca(OH)2 the adsorption of collectors on arsenopyrite is greatly retarded or depressed because the mineral surface is coated by a lot of precipitates, which is hydrophilic in nature as shown by the measured strong repulsive probe-arsenopyrite detachment force. The findings confirm that the flotation behavior of arsenopyrite in xanthate solutions is very similar to that of pyrite.

Feb 27, 2013

By M. Wiber, P. Nicoll

Rio Algom has embarked on a major programme of expansion with the goal of becoming one of the world’s top-performing base-metal mining and metals distribution companies. To assist the company and its operations in achieving its business objectives, we are implementing an environment, health and safety (EHS) management system, built to be compatible with the 14001 model. We recognize that a sustainable development approach for Rio Algom includes outstanding performance in EHS and community responsibility and is essential to earn acceptance within the communities where we operate or wish to locate; raise capital; obtain permits, and operate efficiently. We are committed to triple bottom line accountability, i.e. full consideration of environmental, social and economic concerns in our business decision making.

Jan 1, 2000

By H. Matsuoka, M. Kawata, K. Haga, K. Mitsuhashi, C. Tokoro, A. Shibayama, R. Kawarabuki

"The mineral surface characteristic is important for the flotation because it affects the flotation behavior of the mineral. Conventionally, in the flotation process for Cu sulphide ores, the degree of ore floatabilities varies depending on the mineral phase such as chalcopyrite, bornite, or chalcocite. Therefore, mineral surfaces are treated with activators and depressants to control the floatability of target minerals and obtain high recovery performance. There are lots of flotation reagents which have many effects on ores depending on ore characteristics and conditioning methods. For example, sodium hydrosulphide (NaHS) as activator is known to have the effect of resulfurizing and activating oxidized surface of chalcocite and bornite. On the other hand, NaHS is reported to depress chalcopyrite floatability. In this study, the evaluation of mineral surfaces was conducted to predict flotation behavior. Activation of Cu minerals (chalcocite, bornite, and chalcopyrite) by NaHS was experimented. The three Cu minerals were treated in two steps. Firstly, they were oxidized in the drying oven. Secondly, they were treated with NaHS solution. After each treatment step, each mineral was measured by contact angle apparatus then analyzed by X-ray photoelectron spectroscopy (XPS). The results of surface characteristics after oxidation and NaHS treatment were utilized to accomplish the study’s objective. INTRODUCTIONCopper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are well-known abundant copper-containing minerals. Generally, these minerals are recovered and concentrated via collector flotation. In flotation, the wettability of the mineral surface is an important factor in its recovery. When the surface is hydrophobic, the mineral has high floatability and when the surface is hydrophilic, it has low floatability. Usually, Cu sulfide minerals have high floatability. However when their surfaces are oxidized, their floatability becomes lower in flotation. In this case of surface oxidation occurrence, activators are added before flotation to modify the surface property of the Cu sulfide minerals so that they can be floated at a certain flotation condition. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao et al. (2018) reported that NaHS is often used as sulfurizer for oxidized sulfide minerals (Becker et al., 2014, Clark et al., 2000, Newell et al., 2006, 2007, Newell and Bradshaw, 2007). Although the floatability of Cu sulfide minerals was raised by adding NaHS generally, the results of this flotation study showed that the flotation behaviors of mixed chalcocite, bornite, and chalcopyrite were different. Therefore, it was considered that NaHS works differently for each mineral."

Jan 1, 2018

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

With constantly rising energy costs it is ever more important that we look at ways of im- proving comminution efficiency both in terms of power consumed as well as capital costs required for purchasing and installing equipment. I intend to show that commonly used appli- cation criteria, which is presently accepted for designing crushing and screening plants, need drastic revision if it is to be used to accura- tely design, predict and refine performance in new and existing facilities. Unless we can calculate performance accurately, we cannot minimise capital investment and maximize Profitability.

Jan 1, 1978

Over the last four years, a major collaboration between CSIRO-MIS, UCT and JKMRC has produced two significant advances in the modelling of comminution. The Universal Comminution Model (UCM) uses parametric SPH/DEM studies of comminution and separation devices to calibrate mathematical models which are suitable for industrial use. The Virtual Comminution Machine (VCM) uses the same computationally intensive techniques based on discrete element modelling (DEM) and smoothed particle hydrodynamics (SPH) to directly model any comminution device by combining a CAD file describing the machine design, sophisticated ore characterisation methods and advanced particle scale flow and breakage simulation. The UCM should be useful for process analysis and optimisation of existing equipment and circuits while the VCM should make a major contribution to the evaluation and development of new machines. Progress to date is encouraging with several processes now well described using DEM. This paper also reports on progress towards combining DEM for particles with a realistic slurry model based on SPH for different types of comminution devices. In due course, this combination should allow accurate modelling of particle transport in wet mills to be combined with DEM models.

Jan 1, 2014

Application of microprocessors, programmable logic devices, and other computer-oriented hardware and software on-board large surface mining equipment to optimize availability and productivity, stretch machine life, and protect against catastrophic breakdown has been a goal of heavy-equipment manufacturers for several years. Progress in this direction has not been as rapid as many manufacturers anticipated in the mid-1980s, and, on the other side of the coin, mining industry and machine operator acceptance of such products has not always been enthusiastic. However, the trend toward such development seems undeniable. Large surface mining equipment in the future will doubtless carry more, and not fewer, applications of computers and computer-related products. The intensity of development interest and degree of progress in commercializing such on-board computer and computer-related products on surface mining equipment varies considerably among the manufacturers. Summarized here are the on-board computer-oriented products of three heavy-equipment suppliers-P&H Harnishfeger, Marathon LeTourneau, and Haulpak not a comprehensive survey, but, perhaps indicative of the direction such development is taking.

Jan 1, 1990